TAR8D01K TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT SILICON MONOLITHIC TAR8D01K Dual Low-Dropout Regulator TAR8D01K is a bipolar type 2-output power supply with a control pin. ON and OFF can be switched using the control pin. Features • Include 2-LDO regulators. (2.5V, 2.8V) • Output power supply can be independent control. • Overtemperature/overcurrent protection. • Very small 8-pin package. Weight: 0.01 g (typ.) Pin Assigment (top view) VOUT (A) VIN 8 7 VOUT (B) CONT (B) 6 5 VOUT (A) = 2.5 V VOUT (B) = 2.8 V 1 2 3 4 NOISE (A) NOISE (B) CONT (A) GND Marking 8D01 Overtemperature protection and overcurrent protection function are not necessary of operating ratings below the absolute maximum ratings. Do not use device under conditions in which their absolute maximum ratings will be exceeded. 1 2007-11-01 TAR8D01K Absolute Maximum Ratings (Ta = 25°C) Characteristics Supply Voltage Symbol Rating Unit VIN 15 V 100 mA Output Current (VOUT (A) ) IOUT (A) Output Current (VOUT (B) ) IOUT (B) 200 (Note 1) 400 (Note 2) Power Dissipation PD Operation Temp Range Topr −40~85 °C Storage Temp Range Tstg −55~150 °C Note: mW Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Unit Rating 2 Note 2: Mounted on a glass epoxy circuit board of 30 mm × 30 mm Pad dimansion of 70 mm Electrical Characteristics (unless otherwise specified, VIN = VOUT (B) + 1 V, IOUT = 30 mA, CIN = 1 μF, COUT = 10 μF, CNOISE = 0.01 μF, Tj = 25°C) 2.5 V output Characteristics (VOUT (A)) Characteristics Symbol Test Condition Output Voltage VOUT IOUT = 30 mA Dropout Voltage VIN-VOUT IOUT = 30 mA Input Voltatge VIN Min Typ Max Unit 2.43 2.5 2.57 V 120 180 VOUT + 0.18 V ⎯ 15 V Load Regulation Reg･load IOUT = 0 mA~30 mA ⎯ 2 12 mV Line Reguration Reg･line VIN = 3.8 V~15.0 V ⎯ 3 15 mV Temp. Coeffcient TCVO Ta = −40°C~85°C ⎯ 100 ⎯ ppm/°C ⎯ 70 ⎯ dB ⎯ 30 ⎯ μVrms Min Typ Max Unit 2.73 2.8 2.87 V Ripple Rejection R.R IOUT = 10 mA, f = 1 kHz, VRipple = 500 mVp-p, Ta = 25°C Output Noise Voltage VNO IOUT = 10 mA, 10 Hz < =f< = 10 kHz, Ta = 25°C 2.8 V output Characteristics (VOUT (B) ) Characteristics Symbol Test Condition Output Voltage VOUT IOUT = 30 mA Dropout Voltage VIN-VOUT IOUT = 30 mA Input Voltatge VIN 120 180 VOUT + 0.18 V ⎯ 15 V Load Regulation Reg･load IOUT = 0 mA~30 mA ⎯ 2 12 mV Line Reguration Reg･line VIN = 3.8 V~15.0 V ⎯ 3 15 mV Temp. Coeffcient TCVO Ta = −40°C~85°C ⎯ 100 ⎯ ppm/°C ⎯ 70 ⎯ dB ⎯ 30 ⎯ μVrms Ripple Rejection R.R IOUT = 10 mA, f = 1 kHz, VRipple = 500 mVp-p, Ta = 25°C Output Noise Voltage VNO IOUT = 10 mA, 10 Hz < =f< = 10 kHz, Ta = 25°C 2 2007-11-01 TAR8D01K Common Characteristics Characteristics Stand-by Current Symbol Min Typ Max Unit VCT = 0 V ⎯ ⎯ 1 μA IB1 IOUT (A) = 0 mA, IOUT (B) = 0 mA ⎯ 350 700 μA IB2 IOUT (A) = 30 mA, IOUT (B) = 30 mA ⎯ 850 1800 μA IB (OFF) Quiescent Current Test Condition Control Voltage (ON) VCT (ON) ⎯ 1.5 ⎯ VIN V Control Voltage (OFF) VCT (OFF) ⎯ ⎯ ⎯ 0.4 V Control Input Current ICT ⎯ ⎯ 15 μA VCT = 1.5 V (output ON) 3 2007-11-01 TAR8D01K Application Note・ Recommended Application circuit 10 μF 8 7 2 6 3 5 Control level A-channel B-channel HIGH ON ON LOW OFF OFF 4 0.01 μF 1 0.01 μF VOUT (B) COUT (B) VIN 1 μF 10 μF VOUT (A) NOISE (A) NOISE (B) CONT (A) GND The noise capacitor should be connected to NOISE pin to GND for stable operation. The recommended value is higher than 0.0047μF. The figure above shows commended configuration for using a point regulator. Insert a capacitor for stable input/output operation. If the control function is not to be used, Toshiba recommended that the control pin be connected to the VCC pin. ・ 4 2007-11-01 TAR8D01K Ripple Rejection TAR8D01K feature a circuit with an excellent ripple rejection characteristic. Because the circuit also features an excellent output fluctuation characteristic for sudden supply voltage drops, the circuit is ideal for in the RF blocks incorporated in all mobile telephones. Ripple Rejection − f Input Transient Responce VOUT(A) 80 Ripple Rejection (dB) 70 Input Voltage 10 μF 60 50 3.1 V 2.2 μF 40 2.8 V 1 μF 20 10 0 10 100 Output voltage 2.5 V 30 VIN = 4.0 V, CNOISE = 0.01 μF, Ta = 25°C, CIN = 1 μF, CIN = 1 μF, Vripple = 500 mVp−p, Iout = 10 mA, Ta = 25°C Cout = 10 μF, CNOISE = 0.01 μF, VIN: 3.1 V → 2.8 V, Iout = 30 mA 1k 10 k Frequency f 100 k 300 k 0 1 2 3 (Hz) 4 5 6 time t (ms) 7 8 9 10 Input Transient Responce VOUT(B) Input Voltage 3.4 V 3.1 V Output voltage 2.8 V Ta = 25°C, CIN = 1 μF, Cout = 10 μF, CNOISE = 0.01 μF, VIN: 3.4 V → 3.1 V, Iout = 30 mA 0 1 2 3 4 5 6 time t (ms) 7 8 9 10 NOISE Pin TAR8D01K device incorporate a NOISE pin to reduce output noise voltage. Inserting a capacitor between the NOISE pin and GND reduces output noise. To ensure stable operation, insert a capacitor of 0.0047 μF or more between the NOISE pin and GND. CNOISE − VN 60 Output noise voltage VN (μV) CIN = 1 μF, Cout = 10 μF, Iout = 10 mA, Ta = 25°C 50 40 30 20 10 0 0.001 μ 0.01 μ NOISE capacitance 0.1 μ CNOISE 1.0 μ (F) 5 2007-11-01 TAR8D01K VOUT(B) – VIN VOUT(A) – VIN IOUT = 1 mA, CIN = 1 μF, COUT = 10 μF, 4 3 2 1 0 0 5 10 Input voltage IOUT = 1 mA, CIN = 1 μF, COUT = 10 μF, CNOISE = 0.01 μF Pulse width = 1 ms (V) CNOISE = 0.01 μF VOUT 5 6 Output voltage Output voltage VOUT (V) 6 VIN 5 4 3 2 1 0 0 15 5 VN – f VIN 15 (V) PD – Ta 500 VIN = VOUT + 1 V, IOUT = 10 mA, CIN = 1 μF, (mW) COUT = 10 μF, CNOISE = 0.01 μF, 10 Hz < f < 100 kHz, Ta = 25°C 400 PD 1 Power dissipation VN (μV/√ Hz ) 10 Input voltage (V) 10 Output noise voltage Pulse width = 1 ms 0.1 0.01 300 200 Circuit board material: grass epoxy. Circuit board dimension: 30 mm × 30 mm Pad area: 70 mm2 (t = 0.8mm) 100 −40 0 40 0.001 10 100 1k Frequency f 10 k Ambient temperature 100 k 80 Ta 120 (°C) (Hz) 6 2007-11-01 TAR8D01K Package Dimensions Weight: 0.01 g (Typ.) 7 2007-11-01 TAR8D01K RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 8 2007-11-01