2SK2963 TOSHIBA Field Effect Transistor Silicon N Channel MOS Type (L2-π-MOS V) 2SK2963 DC-DC Converter, Relay Drive and Motor Drive Applications • 4 V gate drive • Low drain-source ON resistance: RDS (ON) = 0.5 Ω (typ.) • High forward transfer admittance: |Yfs| = 1.2 S (typ.) Unit: mm • Low leakage current: IDSS = 100 μA (max) (VDS = 100 V) • Enhancement-mode: Vth = 0.8 to 2.0 V (VDS = 10 V, ID = 1 mA) Absolute Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit Drain-source voltage VDSS 100 V Drain-gate voltage (RGS = 20 kΩ) VDGR 100 V Gate-source voltage VGSS ±20 V (Note 1) ID 1 Pulse (Note 1) IDP 3 PD 0.5 W (Note 2) PD 1.5 W Single pulse avalanche energy (Note 3) EAS 137 mJ Avalanche current IAR 1 A Repetitive avalanche energy (Note 4) EAR 0.05 mJ Channel temperature Tch 150 °C Storage temperature range Tstg −55 to 150 °C DC Drain current Drain power dissipation Drain power dissipation A JEDEC ⎯ JEITA ⎯ TOSHIBA 2-5K1B Weight: 0.05 g (typ.) Note 1: Please use devices on condition that the channel temperature is below 150°C. Note 2: Mounted on ceramic substrate (25.4 mm × 25.4 mm × 0.8 mm) Note 3: VDD = 25 V, Tch = 25°C (initial), L = 221 mH, RG = 25 Ω, IAR = 1 A Note 4: Repetitive rating: pulse width limited by maximum junction temperature. Note 5: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). This transistor is an electrostatic sensitive device. Please handle with caution. Thermal Characteristics Characteristics Thermal resistance, channel to ambient Symbol Max Unit Rth (ch-a) 250 °C/W 1 2007-03-16 2SK2963 Marking Z B (The two digits represent the part number.) Electrical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Gate leakage current IGSS VGS = ±16 V, VDS = 0 V ⎯ ⎯ ±10 μA Drain cut-off current IDSS VDS = 100 V, VGS = 0 V ⎯ ⎯ 100 μA Drain-source breakdown voltage Gate threshold voltage V (BR) DSS ID = 10 mA, VGS = 0 V 100 ⎯ ⎯ V Vth VDS = 10 V, ID = 1 mA 0.8 ⎯ 2.0 V VGS = 4 V, ID = 0.5 A ⎯ 0.65 0.95 VGS = 10 V, ID = 0.5 A ⎯ 0.5 0.7 Ω Drain-source ON resistance RDS (ON) Forward transfer admittance |Yfs| VDS = 10 V, ID = 0.5 A 0.6 1.2 ⎯ S Input capacitance Ciss VDS = 10 V, VGS = 0 V, f = 1 MHz ⎯ 140 ⎯ pF Reverse transfer capacitance Crss VDS = 10 V, VGS = 0 V, f = 1 MHz ⎯ 20 ⎯ pF Output capacitance Coss VDS = 10 V, VGS = 0 V, f = 1 MHz ⎯ 45 ⎯ pF ⎯ 8 ⎯ ⎯ 13 ⎯ ⎯ 45 ⎯ Turn-on time tr ton 50 Ω Switching time Fall time ID = 0.5 A 10 V VGS 0V tf VOUT RL = 50 Ω Rise time VDD ∼ − 50 V ns toff Duty ≤ 1%, tw = 10 μs ⎯ 175 ⎯ Total gate charge (gate-source plus gate-drain) Qg VDD ∼ − 80 V, VGS = 10 V, ID = 1 A ⎯ 6.3 ⎯ nC Gate-source charge Qgs VDD ∼ − 80 V, VGS = 10 V, ID = 1 A ⎯ 4.3 ⎯ nC Qgd VDD ∼ − 80 V, VGS = 10 V, ID = 1 A ⎯ 2 ⎯ nC Turn-off time Gate-drain (“miller”) charge Source-Drain Ratings and Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Continuous drain reverse current (Note 1) IDR ⎯ ⎯ ⎯ 1 A Pulse drain reverse current IDRP ⎯ ⎯ ⎯ 3 A Forward voltage (diode) VDSF IDR = 1 A, VGS = 0 V ⎯ ⎯ −1.5 V Reverse recovery time trr IDR = 1 A, VGS = 0 V, dIDR/dt = 50 A/μs ⎯ 80 ⎯ ns Reverse recovery charge Qrr IDR = 1 A, VGS = 0 V, dIDR/dt = 50 A/μs ⎯ 140 ⎯ μC (Note 1) 2 2007-03-16 2SK2963 3 2007-03-16 2SK2963 4 2007-03-16 2SK2963 5 2007-03-16 2SK2963 RESTRICTIONS ON PRODUCT USE 20070701-EN • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 6 2007-03-16