Features • Fast Read Access Time – 120 ns • Automatic Page Write Operation • • • • • • • • • • • – Internal Address and Data Latches for 128 Bytes – Internal Control Timer Fast Write Cycle Time – Page Write Cycle Time – 10 ms Maximum – 1 to 128-byte Page Write Operation Low Power Dissipation – 50 mA Active Current – 10 mA CMOS Standby Current Hardware and Software Data Protection DATA Polling for End of Write Detection High Reliability CMOS Technology – Endurance: 5.104 Read Cycles – Data Retention: 10 Years Operating Range: 4.5V to 5.5V, -55 to +125°C CMOS and TTL Compatible Inputs and Outputs No Single Event Latch-up below a LET Threshold of 80 MeV/mg/cm2 Tested up to a Total Dose of (according to MIL STD 883 Method 1019): – 10 kRads (Si) Read-only Mode when Biased – 30 kRads (Si) Read-only Mode when Unbiased JEDEC Approved byte-Wide Pinout 435 Mils Wide 32-Pin Flat Pack Package AT28C010-12DK Mil Space 1-megabit (128K x 8) Paged Parallel EEPROMs AT28C010-12DK Description The AT28C010-12DK is a high-performance Electrically Erasable and Programmable Read-Only Memory. Its one megabit of memory is organized as 131,072 words by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 120 ns with power dissipation of just 275 mW. When the device is deselected, the CMOS standby current is less than 10 mA. Preliminary The AT28C010-12DK is accessed like a Static RAM for the read or write cycle without the need for external components. The device contains a 128-byte page register to allow writing of up to 128 bytes simultaneously. During a write cycle, the address and 1 to 128 bytes of data are internally latched, freeing the address and data bus for other operations. Following the initiation of a write cycle, the device will automatically write the latched data using an internal control timer. The end of a write cycle can be detected by DATA POLLING of I/O7. Once the end of a write cycle has been detected a new access for a read or write can begin. Atmel's 28C010 has additional features to ensure high quality in manufacturing. The device utilizes internal error correction for extended endurance and improved data retention characteristics. An optional software data protection mechanism is available to guard against inadvertent writes. The device also includes an extra 128 bytes of EEPROM for device identification or tracking. Rev. 4259D–AERO–10/09 1 Pin Configuration Pin Name Function A0 - A16 Addresses CE Chip Enable OE Output Enable WE Write Enable I/O0 - I/O7 Data Inputs/Outputs NC No Connect FLATPACK Top View A16 A15 A12 A7 A6 NC A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC NC WE A14 A13 A8 A9 A11 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 Block Diagram 2 AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK Device Operation • READ: The AT28C010-12DK is accessed like a Static RAM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state when either CE or OE is high. This dual-line control gives designers flexibility in preventing bus contention in their system. • BYTE WRITE: A low pulse on the WE or CE input with CE or WE low (respectively) and OE high initiates a write cycle. The address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by the first rising edge of CE or WE. Once a byte write has been started it will automatically time itself to completion. Once a programming operation has been initiated and for the duration of tWC, a read operation will effectively be a polling operation. • PAGE WRITE: The page write operation of the AT28C010-12DK allows 1 to 128 bytes of data to be written into the device during a single internal programming period. A page write operation is initiated in the same manner as a byte write; the first byte written can then be followed by 1 to 127 additional bytes. Each successive byte must be written within 150 μs (tBLC) of the previous byte. If the tBLC limit is exceeded the AT28C010-12DK will cease accepting data and commence the internal programming operation. All bytes during a page write operation must reside on the same page as defined by the state of the A7 - A16 inputs. For each WE high to low transition during the page write operation, A7 - A16 must be the same. • The A0 to A6 inputs are used to specify which bytes within the page are to be written. The bytes may be loaded in any order and may be altered within the same load period. Only bytes which are specified for writing will be written; unnecessary cycling of other bytes within the page does not occur. • DATA POLLING: The AT28C010-12DK features DATA Polling to indicate the end of a write cycle. During a byte or page write cycle an attempted read of the last byte written will result in the complement of the written data to be presented on I/O7. Once the write cycle has been completed, true data is valid on all outputs, and the next write cycle may begin. DATA Polling may begin at anytime during the write cycle. • TOGGLE BIT: In addition to DATA Polling the AT28C010-12DK provides another method for determining the end of a write cycle. During the write operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero. Once the write has completed, I/O6 will stop toggling and valid data will be read. Reading the toggle bit may begin at any time during the write cycle. • DATA PROTECTION: If precautions are not taken, inadvertent writes may occur during transitions of the host system power supply. Atmel has incorporated both hardware and software features that will protect the memory against inadvertent writes. For more information see the application note: http://www.atmel.com/dyn/resources/prod_documents/DOC0544.PDF • HARDWARE PROTECTION: Hardware features protect against inadvertent writes to the AT28C010-12DK in the following ways: (a) VDD sense – if VDD is below 3.8V (typical) the write function is inhibited; (b) VDD power-on delay – once VDD has reached 3.8V the device will automatically time out 5 ms (typical) before allowing a write: (c) write inhibit - holding any one of OE low, CE high or WE high inhibits write cycles; (d) noise filter - pulses of less than 15 ns (typical) on the WE or CE inputs will not initiate a write cycle. SOFTWARE DATA PROTECTION: A software controlled data protection feature has been implemented on the AT28C010-12DK. When enabled, the software data protection (SDP), will prevent inadvertent writes. The SDP feature may be enabled 3 4259D–AERO–10/09 or disabled by the user; the AT28C010-12DK is shipped from Atmel with SDP disabled. • SDP is enabled by the host system issuing a series of three write commands; three specific bytes of data are written to three specific addresses (refer to Software Data Protection Algorithm). After writing the 3-byte command sequence and after tWC the entire AT28C010-12DK will be protected against inadvertent write operations. It should be noted, that once protected the host may still perform a byte or page write to the AT28C010-12DK. This is done by preceding the data to be written by the same 3-byte command sequence used to enable SDP. • Once set, SDP will remain active unless the disable command sequence is issued. Power transitions do not disable SDP and SDP will protect the AT28C010-12DK during power-up and power-down conditions. All command sequences must conform to the page write timing specifications. The data in the enable and disable command sequences is not written to the device and the memory addresses used in the sequence may be written with data in either a byte or page write operation. • After setting SDP, any attempt to write to the device without the 3-byte command sequence will start the internal write timers. No data will be written to the device; however, for the duration of tWC, read operations will effectively be polling operations. • DEVICE IDENTIFICATION: An extra 128 bytes of EEPROM memory are available to the user for device identification. By raising A9 to 12V ± 0.5V and using address locations 1FF80H to 1FFFFH the bytes may be written to or read from in the same manner as the regular memory array. • OPTIONAL CHIP ERASE MODE: The entire device can be erased using a 6-byte software code. Please see Software Chip Erase application note for details. DC and AC Operating Range AT28C010-12DK-12 Operating Temperature (Case) VDD Power Supply 4 -55°C to +125°C 5V ± 10% AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK Operating Modes Mode CE OE WE I/O Read VIL VIL VIH DOUT Write(1) VIL VIH VIL DIN Standby VIH X X High Z Write Inhibit X X VIH Write Inhibit VIH X X High Z Write Inhibit X VIL X DOUT or High Z Write Inhibit VIL VIL VIL No operation Software Chip Clear VIL VIH VIL DIN Software Write Protect VIL VIH VIL DIN High Voltage Chip Clear VIL VH VIL VIH Output Disable X VIH X High Z DOUT or High Z VIH = High Logic, “1” state, VIL = Low Logic “0” state. X = logic “don’t care” state, High Z = high impedance state. VH = Chip clear voltage, DOUT = Data out, and DIN = Data in. Notes: 1. Refer to AC Programming Waveforms 5 4259D–AERO–10/09 Electrical Characteristics Absolute Maximum Ratings* Temperature Under Bias................................ -55°C to +125°C *NOTICE: Storage Temperature ..................................... -65°C to +150°C All Input Voltages (including NC Pins) with Respect to Ground ...................................-0.6V to +6.25V All Output Voltages with Respect to Ground .............................-0.6V to VDD + 0.6V Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on OE and A9 with Respect to Ground ...................................-0.6V to +13.5V DC Characteristics 6 Symbol Parameter Condition Min Max Units IIL , IIH Low Level Input Current VIN = 0V to VDD +1V -10 10 μA IOZL , IOZH Output Leakage Current VI/O = 0V to VDD -10 10 μA ICC3 VDD Standby Current CMOS CE = VDD - 0.3V to VDD + 1V 10 mA ICC2 VDD Standby Current TTL CE = 2.0V to VDD + 1V 10 mA ICC1 VDD Active Current f = 5 MHz; IOUT = 0 mA 50 mA VIL Input Low Voltage 0.8 V VIH Input High Voltage VOL Output Low Voltage IOL = 2.1 mA VOH1 Output High Voltage IOH = -400 μA 2.4 V VOH2 Output High Voltage CMOS IOH = -100 μA; VDD = 4.5V 4,2 V 2.0 V 0.45 V AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK AC Read Characteristics AC Read Waveforms(1)(2)(3)(4) ADDRESS ADDRESS VALID ADDRESS VALID CE TAVQV TELQV OE TELQVPH TELQV TOLQV TOLQV TEHQZ TAVQV OUTPUT Notes: HIGH Z TEHQZ TAXQX OUTPUT VALID TAVQV HIGH Z TAXQX OUTPUT VALID 1. CE may be delayed up to TAVQV - TELQV after the address transition without impact on TAVQV. 2. OE may be delayed up to TELQV - TOLQV after the falling edge of CE without impact on TELQV or by TAVQV - TOLQV after an address change without impact in TAVQV. 3. TEHQZ is specified from OE or CE wichever occurs first (CL = 5 pF). 4. This parameter is characterized and is not 100% tested. 5. If CE is de-asserted, it must remain de-asserted for at least 50ns during read operations otherwise incorrect data may be read. 7 4259D–AERO–10/09 Input Test Waveforms and Measurement Level Output Test Load Pin Capacitance f = 1 MHz, T = 25°C(1) Symbol Typ Max Units Conditions CIN 4 10 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 1. This parameter is 100% characterized and is not 100% tested. AC Write Characteristics 8 Symbol Parameter Min Max Units TAVEL, TAVWL, TOHWL, TOHEL, Address, OE Set-up Time 0 ns TELAX, TWLAX Address Hold Time 50 ns TWLEL, TELWL Chip Select Set-up Time 0 ns TEHWH, TWHEH Chip Select Hold Time 0 ns TELEH, TWLWHI Write Pulse Width (WE or CE) 100 ns TDVEH, TDVWH Data Set-up Time 50 ns TEHDX, TWHDX, TWHOL, TEHOL Data, OE Hold Time 0 ns TWPH Write Pulse Width High 50 ns AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK AC Write Waveforms WE Controlled TOHWL TAVWL TWHOL TWLAX TWHEH TELWL TWPH TWLWH1 TDVWH TWHDX CE Controlled TOHEL TAVEL EHOL TELAX EHWH TWLEL TWPH TELEH TDVEH TEHDX 9 4259D–AERO–10/09 Page Mode Characteristics Symbol Parameter TWHWL1 Write Cycle Time TAVWL, TOHWL Address Set-up Time, OE Set up time 0 ns TWLAX Address Hold Time 50 ns TDVWH Data Set-up Time 50 ns Data Hold Time, OE Hold time 0 ns 100 ns TWHDX, TWHOL Min TWLWH1 Write Pulse Width TWHWL2 Byte Load Cycle Time TWPH Write Pulse Width High Max Units 10 ms 150 50 μs ns Page Mode Write Waveforms (1)(2) TWPH TWLWH1 TAVWL TWLAX TWHWL2 TWHDX TDVWH TWHWL1 Notes: 10 1. A7 through A16 must specify the page address during each high to low transition of WE (or CE). 2. OE must be high only when WE and CE are both low. AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK Chip Erase Waveforms tS = 5 msec (min.) tW = tH = 10 msec (min.) VH = 12.0V ± 0.5V Software Data Figure 1. Protection Enable Algorithm(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED(2) LOAD DATA XX TO ANY ADDRESS(3) LOAD LAST BYTE TO LAST ADDRESS Notes: ENTER DATA PROTECT STATE 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Write Protect state will be activated at end of write even if no other data is loaded. 3. 1 to 128 bytes of data are loaded. 11 4259D–AERO–10/09 Figure 2. Protection Disable Algorithm(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 80 TO ADDRESS 5555 LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 20 TO ADDRESS 5555 EXIT DATA PROTECT STATE(3) LOAD DATA XX TO ANY ADDRESS(4) LOAD LAST BYTE TO LAST ADDRESS Notes: 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Write Protect state will be activated at end of write even if no other data is loaded. 3. Write Protect state will be deactivated at end of write period even if no other data if loaded. 4. 1 to 128 bytes of data are loaded. 12 AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK Software Protected Program Cycle Waveform(1)(2)(3) TWLWH1 TWPH TWHWL2 TAVWL TWLAX TDVWH TWHDX TWHWL1 Notes: 1. A0 - A14 must conform to the addressing sequence for the first 3 bytes as shown above. 2. After the command sequence has been issued and a page write operation follows, the page address inputs (A7 - A16) must be the same for each high to low transition of WE (or CE). 3. OE must be high only when WE and CE are both low. 13 4259D–AERO–10/09 Data Polling Characteristics(1) Symbol Parameter Min TWHDX Data Hold Time 10 ns TWHOL OE Hold Time 10 ns (2) TOLQV OE Access Time tWR Write Recovery Time Notes: Typ Max Units ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See AC Read Characteristics. Data Polling Waveforms TWHOL TWHDX 14 TOLQV AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK Toggle Bit Characteristics(1) Symbol Parameter TWHDX Data Hold Time TWHOL OE Hold Time Min Max OE Access Time TOEHP OE High Pulse TWR Write Recovery Time Units 10 ns 10 ns (2) TOLQV Notes: Typ ns 150 ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See AC Read Characteristics. Toggle Bit Waveforms(1)(2)(3) TWHOL TWHDX Notes: TOEHP TOLQV 1. Toggling either OE or CE or both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any addres location may be used but the address should not vary. 15 4259D–AERO–10/09 Ordering Information tACC (ns) ICC (mA) Active Ordering Code Package Standby AT28C010-12DK-E 120 50 10 AT28C010-12DK-MQ AT28C010-12DK-SV 16 Packing Engineering Samples FP32.4 Military Level B Space Level B AT28C010-12DK 4259D–AERO–10/09 AT28C010-12DK Packaging Information FP32.435 32F, 32-Lead, Non-Windowed, Ceramic Bottom Brazed Flat Package (Flatpack) Dimensions in Inches and Millimeters MIL-STD-1835 F-18 CONFIG B JEDEC OUTLINE MO-115 17 4259D–AERO–10/09 Document Revision History Changes from Rev. C to Rev. D 18 1. Page 7 updated to be in compliance with military version of the datasheet which implements a condition on the CE Pulse High Time to avoid bad output data when a very fast read enable is used by application. AT28C010-12DK 4259D–AERO–10/09 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 e-mail [email protected] Web Site http://www.atmel.com Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2005. All rights reserved. Atmel®, logo and combinations thereof, are registered trademarks, and Everywhere You Are® are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4259D–AERO–10/09 xM