SE3003-DC90A Tentative Printhead Under development High speed thermal printhead (300 dots / inch) SE3003-DC90A High speed, high quality, and high durability are achieved by using step free structure with high performance partial glaze and highly conductive overcoat layer. SE300*-DC90A series are lined up which can accommodate with all types of barcode labeling printers from Direct to Thermal Transfer, normal to high speed (over 300mm/s). zApplications Barcode printers Label printers Packaging printers ATM Ticket printers Scale printers zFeatures 1) ROHM new technology “STEP FREE” structure will provide, high corrosion resistance, better resistance against scratching damage, high efficiency. 2) Standard glazed components to accommodate thick paper. 3) High speed clock to facilitate external heat history control. 4) Using a hard conductive film as a protective film on the heating element offers excellent resistance to electrostatic damage. zExternal dimensions (Unit : mm) 7.3±0.3 MAX.12 φ3 H10 Length 4 Effective Depth 3 #20 #6 20.656±0.2 (36) MAX.5 #2 (25) 20±0.3 17.8±0.2 DOT No.1 MIN.4.3 (3.5) MAX.48 (4.344) 40±0.3 6±0.5 25±0.5 MAX.φ20 DOT No.1 90±0.5 81.312 φ 3 H10 Effective Depth 3 #1 M3 Effective Depth 3 TYPE OF PRINTHEAD CONNECTOR:A #1 CONNECTOR:B #19 Note: No heat history control function inside the thermal printhead. External heat history control is required for high speed printing. 1/3 SE3003-DC90A Tentative Printhead Under development zEquivalent circuit DOT#1 DOT #960 VH 220µF 35V GND BEO STB2 STB1 LAT LATCH DI 2 DI 1 CLK VDD GND TM TM DI No. DOT No. STB No. DOT No. DI 2 960 to 449 STB2 960 to 449 DI 1 448 to STB1 448 to 1 1 2/3 SE3003-DC90A Tentative Printhead Under development zPin assignments HIROSE JST No. Circuit No. Circuit No. Circuit 1 VDD 2 BEO 1 VH 3 GND 4 DI2 2 VH 5 N.C. 6 CLK 3 VH 7 LAT 8 GND 4 GND 9 GND 10 DI1 5 GND 11 N.C. 12 GND 6 GND 13 VDD 14 STB2 15 STB1 16 TM 17 TM 18 SENS1 19 SENS2 20 SENS3 zCharacteristics Parameter Symbol Typical Unit Effective printing width − 81.3 mm Dot pitch − 0.0847 mm Total dot number − 960 dots Rave 850 Ω VH 24 V Average resistance value Applied voltage Applied power PO 0.61 W / dot SLT 0.42 ms Maximum number of dots energized simultaneously − 960 dots Maximum clock frequency − 10 MHz Maximum roller diameter − φ 20 mm Running life / pulse life − 150 / 108 km / pulses Operating temperature − 5 to 45 °C Print cycle 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1