ROHM NF3004

NF3004-WA30A
Printhead
Under development
High speed thermal printhead
(with thermal historical control)
NF3004-WA30A
NF-WA30 series are the thermal printheads developed for high-speed / high-resolution printing for the market of bar-code
printer & scale-printer, based on “step-free” structure. These printheads realize ultra-highspeed printing with long life &
high reliability.
zApplications
Barcode printer
Label printer
Packaging printer
Ticket printer
Scale printer
ATM
zFeatures
1) High dot reproducibility with step-free structure.
2) High-hardness protect cote type “W-coat” is employed with 150km abrasion life-time.
3) Even without history-control, high-speed printing more than 300mm / s can be achieved at 300dpi with clear print
image. With history-control, 500mm / s printing is also possible at 300dpi.
1/4
NF3004-WA30A
Printhead
Under development
zExternal dimensions (Unit : mm)
DOT No.1
124±0.5
6±0.5
108.416
Ma
x.φ
MAX.51
20
(3.5)
(7.792)
Max.4.5
Max.11
#2
#1
Type of PRINTHEAD
#20
CONNECTOR:A
#19
#6
#1
CONNECTOR:B
3-M3
Effective Depth 3
100±0.2
17.8±0.2
14.208±0.3
40±0.3
80±0.3
(21.3)
2.8±0.2
31.0±0.5
(43)
φ 3 H10
Effective Depth 3
7.3±0.3
10±0.2
φ 3 H10 Length 4
Effective Depth 3
DOT No.1
2/4
NF3004-WA30A
Printhead
Under development
zEquivalent circuit
DOT #1280
VH (COM)
DOT #1
220µF
35V
GND
0.1µF
50V
VDD (+5)
/ STB2
/ STB1
BEO
/ RESET
LATCH REGISTER
SHIFT
REGISTER
SHIFT
REGISTER
CLK (CP)
DI2
DI1
/ LOAD
START
TO EACH IC
INC
SEL2
SEL1
TM
TM
THERMISTOR
30kΩ B: 3950K
DI, STB DIVISION DOT No. CORRESPONDENCE
DI No.
DOT No.
/ STB No.
DI2
1280 to 641
/ STB2
DI1
640 to
DOT No.
1280 to 641
/ STB1
1
640 to
1
zPin assignments
CONNECTOR : A
CONNECTOR : B
No.
Circuit
No.
Circuit
No.
Circuit
No.
Circuit
1
VDD
2
BEO
1
VH (COM)
2
VH (COM)
3
GND
4
DI2
3
VH (COM)
4
GND
5
5
GND
6
GND
GND
6
CLK (CP)
7
/LOAD
8
START
9
INC
10
DI1
11
SEL2
12
SEL1
13
/RESET
14
/STB2
15
/STB1
16
TM
17
TM
18
SENS1
19
SENS2
20
SENS3
3/4
NF3004-WA30A
Printhead
Under development
zCharacteristics
Parameter
Symbol
Typical
Unit
−
108.416
mm
Dot pitch
−
0.0847
mm
Total dot number
−
1280
dots
Rave
850
Ω
VH
24
V
Effective printing width
Average resistance value
Applied voltage
PO
0.57
W/dot
SLT
0.28
ms
Maximum number of dots energized simultaneously
−
1280
dots
Maximum clock frequency
−
8
MHz
Maximum roller diameter
−
φ20
Running life / pulse life
−
150/(1×10 )
km/pulses
Operating temperature
−
5 to 45
°C
Applied power
Print cycle
mm
8
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1