KD2002-DC10A Printheads Thick film thermal printhead (8 dots / mm) KD2002-DC10A The KD2002-DC10A is a 24 V standard thick film thermal printhead with a printing speed up to 6 inches / s that has been developed mainly for label printer use. zApplications High speed label printer High speed bar code printer High speed ticket printer Various high speed terminal printers zFeatures 1) Newly developed thick-film fast response thermal element is employed for this series and 6 inches / s or 150 mm / s is possible without thermal history control. It is possible to print 10 inches / s or 250 mm / s if external thermal history control is used. 2) 150km life realized by attributing durable new protection film. 3) New partial glaze construction makes it compatible with the thermal transfer application. zExternal dimensions (Unit : mm) 6.1±0.4 (5) 65 (4.5) Ma x.φ 20 (3) Max.45 Max.36 DOT #448 56 (EFFECTIVE PRINT WIDTH) DOT #1 #2 #20 #4 #1 Max.10 Max.5.5 17.8±0.2 7.3±0.3 15.3±0.3 (20.8) 25±0.5 #19 #1 CONNECTOR A CONNECTOR B 3-M3 (EFFECTIVE DEPTH 3) φ3H10 LENGTH 4 DOT #448 0±0.2 (EFFECTIVE DEPTH 3) 55.5±0.3 55±0.3 28±0.3 56±0.3 φ3H10 (EFFECTIVE DEPTH 3) 1/3 KD2002-DC10A Printheads zEquivalent circuit DOT #448 VH DOT #1 VSF GND L/S #448 #193 #192 #1 VDD STB2 STB1 N.C. LATCH REGISTER /LAT CLK SHIFT REGISTER SHIFT REGISTER DI2 DO2 DI1 DO1 TM THERMISTOR 30kΩ B: 3950K TM CONNECTOR VSF : Usually VSF and VH are connected. When measuring R value of Heatelement , VSF and VH should be separated. DI No. DOT No. STB No. DOT No. DI1 1 to 192 STB1 1 to 192 DI2 193 to 448 STB2 193 to 448 Fig. 1 zPin assignments CONNECTOR A CONNECTOR B No. Circuit No. Circuit No. Circuit 1 GND 11 TM 1 VH 2 VSF 12 TM 2 VH 3 GND 13 DI1 3 GND 4 VDD 14 DO1 4 GND 5 STB2 15 N.C. 6 CLK 16 N.C. 7 DI2 17 N.C. 8 DO2 18 N.C. 9 STB1 19 N.C. 10 LAT 20 N.C. 2/3 KD2002-DC10A Printheads zTiming chart tw CLK CLOCK(CLK) t setup DI t hold DI DATA IN(DI) High : BLACK Low : WHITE td DO DATA OUT(DO) High : BLACK Low : WHITE t setup LAT t hold LAT LATCH(LAT) High : HOLD Low : THROUGH tw LAT t setup STB STROBE(STB) tdo tdo DRIVER OUT Fig.2 zCharacteristics Parameter Symbol Typical Unit Effective printing width − 56 mm Dot pitch − 0.125 mm − 448 dots Rave 650 Ω Total dot number Average resistance value Applied voltage VH 24 V Applied power PO 0.82 W / dot Print cycle SLT 0.82 ms Maximum number of dots energized simultaneously − 448 dots Maximum clock frequency MHz − 12 Maximum roller diameter − φ20.0 Running life / pulse life − 150 / (1×108) km / pulses Operating temperature − 5 to 45 °C mm 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1