S29WSxxxN MirrorBit™ Flash Family S29WS256N, S29WS128N, S29WS064N 256/128/64 Megabit (16/8/4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory Data Sheet PRELIMINARY General Description The Spansion S29WS256/128/064N are MirrorbitTM Flash products fabricated on 110 nm process technology. These burst mode Flash devices are capable of performing simultaneous read and write operations with zero latency on two separate banks using separate data and address pins. They operate up to 80 MHz and use a single VCC of 1.7–1.95 volts that makes them ideal for today’s demanding wireless applications requiring higher density, better performance and lowered power consumption. Distinctive Characteristics Single 1.8 V read/program/erase (1.70–1.95 V) Command set compatible with JEDEC standards 110 nm MirrorBit™ Technology Simultaneous Read/Write operation with zero latency Hardware (WP#) protection of top and bottom sectors Dual boot sector configuration (top and bottom) 32-word Write Buffer Sixteen-bank architecture consisting of 16/8/4 Mbit for WS256N/128N/064N, respectively Offered Packages Four 16 Kword sectors at both top and bottom of memory array — WS064N: 80-ball FBGA (7 mm x 9 mm) — WS256N/128N: 84-ball FBGA (8 mm x 11.6 mm) Low VCC write inhibit Persistent and Password methods of Advanced Sector Protection 254/126/62 64 Kword sectors (WS256N/128N/ 064N) Programmable burst read modes — Linear for 32, 16 or 8 words linear read with or without wrap-around — Continuous sequential read mode Write operation status bits indicate program and erase operation completion Suspend and Resume commands for Program and Erase operations Unlock Bypass program command to reduce programming time SecSi™ (Secured Silicon) Sector region consisting of 128 words each for factory and customer 20-year data retention (typical) Cycling Endurance: 100,000 cycles per sector (typical) Synchronous or Asynchronous program operation, independent of burst control register settings ACC input pin to reduce factory programming time Support for Common Flash Interface (CFI) Industrial Temperature range (contact factory) RDY output indicates data available to system Performance Characteristics Read Access Times Current Consumption (typical values) Speed Option (MHz) 80 Max. Synch. Latency, ns (tIACC) 66 54 Continuous Burst Read @ 66 MHz 35 mA Simultaneous Operation (asynchronous) 50 mA 69 69 69 Max. Synch. Burst Access, ns (tBACC) 9 11.2 13.5 Max. Asynch. Access Time, ns (tACC) 70 70 Max CE# Access Time, ns (tCE) 70 Max OE# Access Time, ns (tOE) 11.2 Program (asynchronous) 19 mA 70 Erase (asynchronous) 19 mA 70 70 Standby Mode (asynchronous) 20 µA 11.2 13.5 Typical Program & Erase Times Single Word Programming 40 µs Effective Write Buffer Programming (VCC) Per Word 9.4 µs Effective Write Buffer Programming (VACC) Per Word Publication Number S29WSxxxN_00 Revision F 6 µs Sector Erase (16 Kword Sector) 150 ms Sector Erase (64 Kword Sector) 600 ms Amendment 0 Issue Date October 29, 2004 P r e l i m i n a r y Table of Contents 1. Ordering Information . . . . . . . . . . . . . . . . . . . . . .5 2. Input/Output Descriptions & Logic Symbol . . . .6 3. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4. Physical Dimensions/Connection Diagrams . . . .8 4.1 Related Documents ........................................................................ 8 4.2 Special Handling Instructions for FBGA Package ................. 8 4.3 MCP Look-ahead Connection Diagram ................................. 13 5. Additional Resources . . . . . . . . . . . . . . . . . . . . . 15 6. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . 16 6.1 Memory Map .................................................................................... 16 7. Device Operations . . . . . . . . . . . . . . . . . . . . . . . 19 7.1 Device Operation Table ............................................................... 19 7.2 Asynchronous Read ...................................................................... 19 7.3 Synchronous (Burst) Read Mode & Configuration Register ........................................................................20 7.3.1 Continuous Burst Read Mode .......................................... 24 7.3.2 8-, 16-, 32-Word Linear Burst Read with Wrap Around ....................................................................... 25 7.3.3 8-, 16-, 32-Word Linear Burst without Wrap Around ................................................................ 25 7.3.4 Configuration Register ....................................................... 25 7.4 Autoselect ....................................................................................... 26 7.5 Program/Erase Operations ........................................................ 29 7.5.1. Single Word Programming ................................................ 29 7.5.2 Write Buffer Programming ................................................ 31 7.5.3 Sector Erase ........................................................................... 34 7.5.4 Chip Erase Command Sequence ..................................... 38 7.5.5 Erase Suspend/Erase Resume Commands ................... 38 7.5.6 Program Suspend/Program Resume Commands ....... 39 7.5.7 Accelerated Program/Chip Erase ...................................40 7.5.8 Unlock Bypass ........................................................................ 41 7.5.9 Write Operation Status ..................................................... 42 7.6 Simultaneous Read/Write ..........................................................48 7.7 Writing Commands/Command Sequences ..........................48 7.8 Handshaking ...................................................................................48 7.9 Hardware Reset ............................................................................ 49 7.10 Software Reset ............................................................................. 49 8. Advanced Sector Protection/Unprotection . . . 51 8.1 Lock Register .................................................................................. 52 8.2 Persistent Protection Bits .......................................................... 52 8.3 Dynamic Protection Bits .............................................................53 8.4 Persistent Protection Bit Lock Bit ...........................................53 2 8.5 Password Protection Method ...................................................54 8.6 Advanced Sector Protection Software Examples ...............56 8.7 Hardware Data Protection Methods ......................................56 8.7.1. WP# Method .........................................................................56 8.7.2 ACC Method .........................................................................56 8.7.3 Low VCC Write Inhibit .......................................................57 8.7.4 Write Pulse “Glitch Protection” .....................................57 8.7.5 Power-Up Write Inhibit .....................................................57 9. Power Conservation Modes . . . . . . . . . . . . . . . 58 9.1 Standby Mode ................................................................................. 58 9.2 Automatic Sleep Mode ............................................................... 58 9.3 Hardware RESET# Input Operation ...................................... 58 9.4 Output Disable (OE#) ................................................................ 58 10. SecSiTM (Secured Silicon) Sector Flash Memory Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 10.1 Factory SecSiTM Sector .................................................................59 10.2 Customer SecSiTM Sector .......................................................... 60 10.3 SecSiTM Sector Entry and SecSi Sector Exit Command Sequences .......................................................................... 60 11. Electrical Specifications . . . . . . . . . . . . . . . . . . 62 11.1 Absolute Maximum Ratings ....................................................... 62 11.2 Operating Ranges ..........................................................................63 11.3 Test Conditions .............................................................................63 11.4 Key to Switching Waveforms ................................................. 64 11.5 Switching Waveforms ................................................................. 64 11.6 VCC Power-up .............................................................................. 64 11.7 DC Characteristics (CMOS Compatible) .............................65 11.8 AC Characteristics ...................................................................... 66 11.8.1. CLK Characterization ....................................................... 66 11.8.2 Synchronous/Burst Read ...................................................67 11.8.3 Timing Diagrams ................................................................. 68 11.8.4 AC Characteristics—Asynchronous Read ................. 70 11.8.5 Hardware Reset (RESET#) ..............................................72 11.8.6 Erase/Program Timing ........................................................73 11.8.7 Erase and Programming Performance ...........................83 11.8.8 BGA Ball Capacitance ....................................................... 84 12. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 12.1 Common Flash Memory Interface ..........................................88 13. Commonly Used Terms . . . . . . . . . . . . . . . . . . 92 14. Revisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00F0 October 29, 2004 P r e l i m i n a r y List of Figures Figure 4.2. VBH084—84-ball Fine-Pitch Ball Grid Array (FBGA) 8 x 11.6 mm MCP Compatible Package .......................................................... 10 Figure 4.3. 80-ball Fine-Pitch Ball Grid Array (S29WS064N) .................................................................................................................... 11 Figure 4.4. TLC080—80-ball Fine-Pitch Ball Grid Array (FBGA) 7 x 9 mm MCP Compatible Package ............................................................... 12 Figure 4.5. MCP Look-ahead Diagram ................................................................................................................................................... 14 Figure 7.2. Synchronous Read ............................................................................................................................................................. 24 Figure 7.19. Single Word Program....................................................................................................................................................... 30 Figure 7.22. Write Buffer Programming Operation ................................................................................................................................. 34 Figure 7.24. Sector Erase Operation.................................................................................................................................................... 37 Figure 7.33. Write Operation Status Flowchart ...................................................................................................................................... 44 Figure 8.2. Lock Register Program Algorithm ......................................................................................................................................... 55 Figure 11.2. Maximum Positive Overshoot Waveform.............................................................................................................................. 62 Figure 11.3. Test Setup ...................................................................................................................................................................... 63 Figure 11.4. Input Waveforms and Measurement Levels.......................................................................................................................... 64 Figure 11.5. VCC Power-up Diagram ..................................................................................................................................................... 64 Figure 11.6. CLK Characterization ........................................................................................................................................................ 66 Figure 11.7. CLK Synchronous Burst Mode Read .................................................................................................................................... 68 Figure 11.8. 8-word Linear Burst with Wrap Around ............................................................................................................................... 69 Figure 11.9. 8-word Linear Burst without Wrap Around ........................................................................................................................... 69 Figure 11.10. Linear Burst with RDY Set One Cycle Before Data ............................................................................................................... 70 Figure 11.11. Asynchronous Mode Read................................................................................................................................................ 71 Figure 11.12. Reset Timings................................................................................................................................................................ 72 Figure 11.2. Chip/Sector Erase Operation Timings: WE# Latched Addresses ............................................................................................. 74 Figure 11.13. Asynchronous Program Operation Timings: WE# Latched Addresses ..................................................................................... 75 Figure 11.14. Synchronous Program Operation Timings: CLK Latched Addresses ........................................................................................ 76 Figure 11.15. Accelerated Unlock Bypass Programming Timing ................................................................................................................ 77 Figure 11.16. Data# Polling Timings (During Embedded Algorithm) .......................................................................................................... 77 Figure 11.17. Toggle Bit Timings (During Embedded Algorithm) ............................................................................................................... 78 Figure 11.18. Synchronous Data Polling Timings/Toggle Bit Timings ......................................................................................................... 78 Figure 11.19. DQ2 vs. DQ6 ................................................................................................................................................................. 79 Figure 11.20. Latency with Boundary Crossing when Frequency > 66 MHz................................................................................................. 79 Figure 11.21. Latency with Boundary Crossing into Program/Erase Bank ................................................................................................... 80 Figure 11.22. Example of Wait States Insertion ..................................................................................................................................... 81 Figure 11.23. Back-to-Back Read/Write Cycle Timings ............................................................................................................................ 82 October 29, 2004 S29WSxxxN_00_F0 S29WSxxxN MirrorBit™ Flash Family 3 P r e l i m i n a r y List of Tables Read Access Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Current Consumption (typical values) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Typical Program & Erase Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Table 2.1. Input/Output Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Table 6.1. S29WS256N Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 6.2. S29WS128N Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 6.3. S29WS064N Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 7.4. Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 7.5. Address Latency for x Wait States (≤ 80 MHz, WS256N only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Table 7.6. Address Latency for 6 Wait States (≤ 80 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Table 7.7. Address Latency for 5 Wait States (≤ 68 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Table 7.8. Address Latency for 4 Wait States (≤ 54 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Table 7.9. Address Latency for 3 Wait States (≤ 40 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Table 7.10. Address/Boundary Crossing Latency for 6 Wait States (≤ 80 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 7.11. Address/Boundary Crossing Latency for 5 Wait States (≤ 68 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 7.12. Address/Boundary Crossing Latency for 4 Wait States (≤ 54 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 7.13. Address/Boundary Crossing Latency for 3 Wait States (≤ 40 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 7.14. Burst Address Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Table 7.15. Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 7.16. Autoselect Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 7.17. Autoselect Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 7.18. Autoselect Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Table 7.20. Single Word Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Table 7.21. Write Buffer Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 7.23. Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table 7.25. Chip Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Table 7.26. Erase Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Table 7.27. Erase Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Table 7.28. Program Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Table 7.29. Program Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Table 7.30. Unlock Bypass Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Table 7.31. Unlock Bypass Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Table 7.32. Unlock Bypass Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Table 7.34. DQ6 and DQ2 Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Table 7.35. Write Operation Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Table 7.36. Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Table 8.1. Lock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Table 8.2. Sector Protection Schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Table 10.1. SecSiTM Sector Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Table 10.2. SecSi Sector Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Table 10.3. SecSi Sector Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Table 10.4. SecSi Sector Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Table 11.1. Test Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Table 12.1. Memory Array Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Table 12.2. Sector Protection Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 Table 12.3. CFI Query Identification String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Table 12.4. System Interface String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Table 12.5. Device Geometry Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Table 12.6. Primary Vendor-Specific Extended Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 4 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 1 Ordering Information The ordering part number is formed by a valid combination of the following: S29WS 256 N 0S BA W 01 0 PACKING TYPE 0 = Tray (standard; see note 1) 2 = 7-inch Tape and Reel 3 = 13-inch Tape and Reel MODEL NUMBER (Note 3) (Package Ball Count, Package Dimensions, DYB Protect/Unprotect After Power-up) 01 = 84-ball, 8 x 11.6 mm, DYB Unprotect 11 = 80-ball, 7 x 9 mm, DYB Protect TEMPERATURE RANGE (Note 3) W = Wireless (–25°C to +85°C) I = Industrial (–40°C to +85°C, contact factory for availability) PACKAGE TYPE AND MATERIAL BA = Very Thin Fine-Pitch BGA, Lead (Pb)-free Compliant Package BF = Very Thin Fine-Pitch BGA, Lead (Pb)-free Package SPEED OPTION (BURST FREQUENCY) 0S = 80 MHz 0P = 66 MHz 0L = 54 MHz PROCESS TECHNOLOGY N = 110 nm MirrorBit™ Technology FLASH DENSITY 256 = 256 Mb 128 = 128 Mb 064 = 64 Mb DEVICE FAMILY S29WS = 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory S29WSxxxN Valid Combinations (Notes 1, 2, 3) Base Ordering Part Number Speed Option Package Type, Material, & Temperature Range Model Number S29WS256N S29WS128N 0S, 0P, 0L BAW (Lead (Pb)-free Compliant), BFW (Lead (Pb)-free) S29WS064N Notes: 1. Type 0 is standard. Specify other options as required. 2. BGA package marking omits leading “S29” and packing type designator from ordering part number. 3. For 1.5 VIO option, other boot options, or industrial temperature range, contact your local sales office. October 29, 2004 S29WSxxxN_00_F0 Packing Type VIO Range DYB Power Up State 01 Unprotect 11 Protect 01 11 0, 2, 3 (Note 1) 1.70–1.95 V Unprotect Package Type (Note 2) 8 mm x 11.6 mm 84-ball MCP-Compatible Protect 01 Unprotect 11 Protect 7 mm x 9 mm 80-ball MCP-Compatible Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to confirm availability of specific valid combinations and to check on newly released combinations. S29WSxxxN MirrorBit™ Flash Family 5 P r e l i m i n a r y 2 Input/Output Descriptions & Logic Symbol Table identifies the input and output package connections provided on the device. Table 2.1. Input/Output Descriptions Symbol Type A23–A0 Input DQ15–DQ0 I/O CE# Input Chip Enable. Asynchronous relative to CLK. OE# Input Output Enable. Asynchronous relative to CLK. WE# Input VCC Supply VIO Input VSS I/O NC No Connect RDY Output CLK Input AVD# Input Description Address lines for WS256N (A22-A0 for WS128 and A21-A0 for WS064N). Data input/output. Write Enable. Device Power Supply. VersatileIO Input. Should be tied to VCC. Ground. Not connected internally. Ready. Indicates when valid burst data is ready to be read. Clock Input. In burst mode, after the initial word is output, subsequent active edges of CLK increment the internal address counter. Should be at VIL or VIH while in asynchronous mode. Address Valid. Indicates to device that the valid address is present on the address inputs. When low during asynchronous mode, indicates valid address; when low during burst mode, causes starting address to be latched at the next active clock edge. When high, device ignores address inputs. 6 RESET# Input Hardware Reset. Low = device resets and returns to reading array data. WP# Input Write Protect. At VIL, disables program and erase functions in the four outermost sectors. Should be at VIH for all other conditions. ACC Input Acceleration Input. At VHH, accelerates programming; automatically places device in unlock bypass mode. At VIL, disables all program and erase functions. Should be at VIH for all other conditions. RFU Reserved Reserved for future use (see MCP look-ahead pinout for use with MCP). S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 3 Block Diagram DQ15–DQ0 VCC VSS VIO RDY Buffer RDY Input/Output Buffers Erase Voltage Generator State Control Command Register PGM Voltage Generator Chip Enable Output Enable Logic CE# OE# VCC Detector AVD# CLK Burst State Control Timer Burst Address Counter Address Latch WE# RESET# WP# ACC Data Latch Y-Decoder Y-Gating X-Decoder Cell Matrix Amax–A0* * WS256N: A23-A0 WS128N: A22-A0 WS064N: A21-A0 Figure 3.1. October 29, 2004 S29WSxxxN_00_F0 S29WSxxxN Block Diagram S29WSxxxN MirrorBit™ Flash Family 7 P r e l i m i n a r y 4 Physical Dimensions/Connection Diagrams This section shows the I/O designations and package specifications for the S29WSxxxN. 4.1 Related Documents The following documents contain information relating to the S29WSxxxN devices. Click on the title or go to www.amd.com/flash (click on Technical Documentation) or www.fujitsu.com to download the PDF file, or request a copy from your sales office. Migration to the S29WS256N Family Application Note Considerations for X-ray Inspection of Surface-Mounted Flash Integrated Circuits 4.2 Special Handling Instructions for FBGA Package Special handling is required for Flash Memory products in FBGA packages. Flash memory devices in FBGA packages may be damaged if exposed to ultrasonic cleaning methods. The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. 8 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 84-Ball Fine-Pitch Ball Grid Array, 256 & 128 Mb (Top View, Balls Facing Down, MCP Compatible) A10 A1 NC Ball F6 is RFU on 128 Mb device. B2 B3 B4 B5 B6 B7 B8 B9 AVD# RFU CLK RFU RFU RFU RFU RFU C2 C3 C4 C5 C6 C7 C8 C9 WP# A7 RFU ACC WE# A8 A11 RFU D2 D3 D4 D5 D6 D7 D8 D9 A3 A6 RFU RESET# RFU A19 A12 A15 E2 E3 E4 E5 E6 E7 E8 E9 A2 A5 A18 RDY A20 A9 A13 A21 F2 F3 F4 F5 F6 F7 F8 F9 A1 A4 A17 RFU A23 A10 A14 A22 G2 G3 G4 G5 G6 G7 G8 G9 A0 VSS DQ1 RFU RFU DQ6 RFU A16 H2 H3 H4 H5 H6 H7 H8 H9 CE#f1 OE# DQ9 DQ3 DQ4 DQ13 DQ15 RFU J2 J3 J4 J5 J6 J7 J8 RFU DQ0 DQ10 VCC RFU DQ12 DQ7 VSS K2 K3 K4 K5 K6 K7 K8 K9 RFU DQ8 DQ2 DQ11 RFU DQ5 DQ14 RFU L2 L3 L4 L5 L6 L7 L8 L9 RFU RFU RFU VCC RFU RFU RFU RFU NC J9 M1 M10 NC NC Figure 4.1. October 29, 2004 S29WSxxxN_00_F0 84-ball Fine-Pitch Ball Grid Array (S29WS256N, S29WS128N) S29WSxxxN MirrorBit™ Flash Family 9 P r e l i m i n a r y VBH084—84-ball Fine-Pitch Ball Grid Array, 8 x 11.6 mm 0.05 C (2X) D D1 A e 10 9 e 7 8 SE 7 6 E1 E 5 4 3 2 1 M A1 CORNER INDEX MARK L K B 10 H G F E D SD 6 0.05 C (2X) J C B A A1 CORNER 7 NXφb φ 0.08 M C TOP VIEW φ 0.15 M C A B BOTTOM VIEW 0.10 C A2 A A1 C 0.08 C SEATING PLANE SIDE VIEW NOTES: PACKAGE VBH 084 JEDEC 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. N/A 2. ALL DIMENSIONS ARE IN MILLIMETERS. 11.60 mm x 8.00 mm NOM PACKAGE SYMBOL MIN NOM MAX A --- --- 1.00 A1 0.18 --- --- A2 0.62 --- 0.76 3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT AS NOTED). NOTE OVERALL THICKNESS BALL HEIGHT 11.60 BSC. BODY SIZE E 8.00 BSC. BODY SIZE D1 8.80 BSC. BALL FOOTPRINT BALL FOOTPRINT E1 7.20 BSC. MD 12 ROW MATRIX SIZE D DIRECTION ME 10 ROW MATRIX SIZE E DIRECTION N 84 TOTAL BALL COUNT 0.33 --- 0.43 BALL DIAMETER e 0.80 BSC. BALL PITCH SD / SE 0.40 BSC. SOLDER BALL PLACEMENT (A2-A9, B10-L10, M2-M9, B1-L1) DEPOPULATED SOLDER BALLS e REPRESENTS THE SOLDER BALL GRID PITCH. 5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE "D" DIRECTION. SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE "E" DIRECTION. BODY THICKNESS D φb 4. N IS THE TOTAL NUMBER OF SOLDER BALLS. 6 DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 7 SD AND SE ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW. WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW PARALLEL TO THE D OR E DIMENSION, RESPECTIVELY, SD OR SE = 0.000. WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, SD OR SE = e/2 8. NOT USED. 9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS. 10 A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK MARK, METALLIZED MARK INDENTATION OR OTHER MEANS. 3339 \ 16-038.25b Note: BSC is an ANSI standard for Basic Space Centering Figure 4.2. 10 VBH084—84-ball Fine-Pitch Ball Grid Array (FBGA) 8 x 11.6 mm MCP Compatible Package S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 80-ball Fine-Pitch Ball Grid Array, 64 Mb (Top View, Balls Facing Down, MCP Compatible) A1 A2 A3 A4 A5 A6 A7 A8 AVD# RFU CLK RFU RFU RFU RFU RFU B1 B2 B3 B4 B5 B6 B7 B8 WP# A7 RFU ACC WE# A8 A11 RFU C1 C2 C3 C4 C5 C6 C7 C8 A3 A6 RFU RESET# RFU A19 A12 A15 D1 D2 D3 D4 D5 D6 D7 D8 A2 A5 A18 RDY A20 A9 A13 A21 E1 E2 E3 E4 E5 E6 E7 E8 A1 A4 A17 RFU RFU A10 A14 RFU F1 F2 F3 F4 F5 F6 F7 F8 A0 VSS DQ1 RFU RFU DQ6 RFU A16 G1 G2 G3 G4 G5 G6 G7 G8 CE#f1 OE# DQ9 DQ3 DQ4 DQ13 DQ15 RFU H1 H2 H3 H4 H5 H6 H7 H8 RFU DQ0 DQ10 VCC RFU DQ12 DQ7 VSS J1 J2 J3 J4 J5 J6 J7 J8 RFU DQ8 DQ2 DQ11 RFU DQ5 DQ14 RFU K1 K2 K3 K4 K5 K6 K7 K8 RFU RFU RFU VCC RFU RFU RFU RFU Figure 4.3. October 29, 2004 S29WSxxxN_00_F0 80-ball Fine-Pitch Ball Grid Array (S29WS064N) S29WSxxxN MirrorBit™ Flash Family 11 P r e l i m i n a r y TLC080—80-ball Fine-Pitch Ball Grid Array, 7 x 9 mm D1 A D eD 0.15 C (2X) 8 7 SE 7 6 5 E E1 4 3 eE 2 1 K INDEX MARK PIN A1 CORNER J H B 10 TOP VIEW G F E D C B A PIN A1 CORNER 7 SD 0.15 C (2X) BOTTOM VIEW 0.20 C A A2 A1 C 0.08 C SIDE VIEW 6 b 80X 0.15 0.08 M C A B M C NOTES: PACKAGE TLC 080 JEDEC N/A DxE 9.00 mm x 7.00 mm PACKAGE SYMBOL MIN NOM MAX A --- --- 1.20 A1 0.17 --- --- A2 0.81 --- 0.97 NOTE PROFILE 9.00 BSC. BODY SIZE 7.00 BSC. BODY SIZE D1 7.20 BSC. MATRIX FOOTPRINT E1 5.60 BSC. MATRIX FOOTPRINT MD 10 MATRIX SIZE D DIRECTION ME 8 MATRIX SIZE E DIRECTION n 80 0.40 2. ALL DIMENSIONS ARE IN MILLIMETERS. 3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010. 4. e REPRESENTS THE SOLDER BALL GRID PITCH. 5. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE "D" DIRECTION. BALL HEIGHT E 0.35 DIMENSIONING AND TOLERANCING METHODS PER ASME Y14.5M-1994. SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE "E" DIRECTION. BODY THICKNESS D φb 1. n IS THE NUMBER OF POPULTED SOLDER BALL POSITIONS FOR MATRIX SIZE MD X ME. 6 DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 7 SD AND SE ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW. BALL COUNT 0.45 WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW SD OR SE = 0.000. BALL DIAMETER eE 0.80 BSC. BALL PITCH eD 0.80 BSC BALL PITCH SD / SE 0.40 BSC. SOLDER BALL PLACEMENT DEPOPULATED SOLDER BALLS WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, SD OR SE = e/2 8. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS. 9. N/A 10 A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK MARK, METALLIZED MARK INDENTATION OR OTHER MEANS. 3430 \ 16-038.22 \ 10.15.04 Note: BSC is an ANSI standard for Basic Space Centering Figure 4.4. 12 TLC080—80-ball Fine-Pitch Ball Grid Array (FBGA) 7 x 9 mm MCP Compatible Package S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 4.3 MCP Look-ahead Connection Diagram Figure 4.5 shows a migration path from the S29WSxxxN to higher densities and the option to include additional die within a single package. Spansion LLC provides this standard lookahead connection diagram that supports NOR Flash and SRAM densities up to 4 Gigabits NOR Flash and pSRAM densities up to 4 Gigabits NOR Flash and pSRAM and data storage densities up to 4 Gigabits The following multi-chip package (MCP) data sheet(s) are based on the S29WSxxxN. Refer to these documents for input/output descriptions for each product: Publication Number S71WS256_512NC0. The physical package outline may vary between connection diagrams and densities. The connection diagram for any MCP, however, will be a subset of the pinout in Figure 4.5. In some cases, outrigger balls may exist in locations outside the grid shown. These outrigger balls are reserved; do not connect them to any other signal. For further information about the MCP look-ahead pinout, refer to the Design-In Scalable Wireless Solutions with Spansion Products application note, available on the web or through an AMD or Fujitsu sales office. October 29, 2004 S29WSxxxN_00_F0 S29WSxxxN MirrorBit™ Flash Family 13 P r e l i m i n a r y Legend: 96-ball Fine-Pitch Ball Grid Array (Top View, Balls Facing Down) A9 A10 NC NC B2 B9 B10 NC NC NC A1 A2 NC NC B1 NC Shared or NC (not connected) Data-storage Only C2 C3 C4 C5 C6 C7 C8 C9 AVD# VSSds CLK CE#f2 D2 D3 D4 D5 D6 D7 D8 D9 WP# A7 LB#s WP/ACC WE# A8 A11 CE1#ds VCCds RESET#ds CLKds RY/BY#ds E2 E3 E4 E5 E6 E7 E8 E9 A3 A6 UB#s RESET#f CE2s1 A19 A12 A15 F2 F3 F4 A2 A5 A18 F5 F6 F7 F8 F9 RDY A20 A9 A13 A21 G2 G3 G4 G5 G6 G7 G8 G9 A1 A4 A17 CE1#s2 A23 A10 A14 A22 H2 H3 H4 H5 H6 H7 H8 H9 A0 VSS DQ1 VCCs2 CE2s2 DQ6 A24 A16 J2 J3 J4 J5 J6 J7 J8 J2 CE#f1 OE# DQ9 DQ3 DQ4 DQ13 DQ15 CREs Flash Shared Only 1st Flash Only 2nd Flash Only 1st RAM Only 2nd RAM Only K2 K3 K4 K5 K6 K7 K8 K9 CE1#s1 DQ0 DQ10 VCCf VCCs1 DQ12 DQ7 VSS L2 L4 L4 L5 L6 L7 L8 L9 DQ8 DQ2 DQ11 A25 DQ5 VCCnds DoC Only DQ14 LOCK or WP#/ACCds M2 M3 M4 M5 M6 M7 M8 M9 A27 A26 VSSnds VCCf CE2#ds VCCQs1 NC or VCCQds DNU NC or ds N1 N2 N9 N10 NC NC NC NC P1 P2 P9 P10 NC NC NC NC Figure 4.5. 14 RAM Shared Only MCP Look-ahead Diagram S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 5 Additional Resources Visit www.amd.com and www.fujitsu.com to obtain the following related documents: Application Notes Using the Operation Status Bits in AMD Devices Understanding Burst Mode Flash Memory Devices Simultaneous Read/Write vs. Erase Suspend/Resume MirrorBit™ Flash Memory Write Buffer Programming and Page Buffer Read Design-In Scalable Wireless Solutions with Spansion Products Common Flash Interface Version 1.4 Vendor Specific Extensions Specification Bulletins Contact your local sales office for details. Drivers and Software Support Spansion low-level drivers Enhanced Flash drivers Flash file system CAD Modeling Support VHDL and Verilog IBIS ORCAD Technical Support Contact your local sales office or contact Spansion LLC directly for additional technical support: Email US and Canada: [email protected] Asia Pacific: [email protected] Europe, Middle East, and Africa Japan: http://edevice.fujitsu.com/jp/support/tech/#b7 Frequently Asked Questions (FAQ) http://ask.amd.com/ http://edevice.fujitsu.com/jp/support/tech/#b7 Phone US: (408) 749-5703 Japan (03) 5322-3324 Spansion LLC Locations 915 DeGuigne Drive, P.O. Box 3453 Sunnyvale, CA 94088-3453, USA Telephone: 408-962-2500 or 1-866-SPANSION Spansion Japan Limited 4-33-4 Nishi Shinjuku, Shinjuku-ku Tokyo, 160-0023 Telephone: +81-3-5302-2200 Facsimile: +81-3-5302-2674 http://www.spansion.com October 29, 2004 S29WSxxxN_00_F0 15 P r e l i m i n a r y 6 Product Overview The S29WSxxxN family consists of 256, 128 and 64Mbit, 1.8 volts-only, simultaneous read/ write burst mode Flash device optimized for today’s wireless designs that demand a large storage array, rich functionality, and low power consumption. These devices are organized in 16, 8 or 4 Mwords of 16 bits each and are capable of continuous, synchronous (burst) read or linear read (8-, 16-, or 32-word aligned group) with or without wrap around. These products also offer single word programming or a 32-word buffer for programming with program/ erase and suspend functionality. Additional features include: Advanced Sector Protection methods for protecting sectors as required 256 words of secured silicon (SecSi™) area for storing customer and factory secured information. The SecSi Sector is One Time Programmable and Protectable (OTTP). 6.1 Memory Map The S29WS256/128/064N Mbit devices consist of 16 banks organized as shown in Tables 6.1– 6.3. Table 6.1. Bank Size 2 MB Sector Count 4 Sector Size (KB) 32 Bank 0 S29WS256N Sector & Memory Address Map Sector/ Sector Range Address Range SA000 000000h–003FFFh SA001 004000h–007FFFh SA002 008000h–00BFFFh SA003 00C000h–00FFFFh 15 128 SA004 to SA018 010000h–01FFFFh to 0F0000h–0FFFFFh 2 MB 16 128 1 SA019 to SA034 100000h–10FFFFh to 1F0000h–1FFFFFh 2 MB 16 128 2 SA035 to SA050 200000h–20FFFFh to 2F0000h–2FFFFFh 2 MB 16 128 3 SA051 to SA066 300000h–30FFFFh to 3F0000h–3FFFFFh 2 MB 16 128 4 SA067 to SA082 400000h–40FFFFh to 4F0000h–4FFFFFh 2 MB 16 128 5 SA083 to SA098 500000h–50FFFFh to 5F0000h–5FFFFFh 2 MB 16 128 6 SA099 to SA114 600000h–60FFFFh to 6F0000h–6FFFFFh 2 MB 16 128 7 SA115 to SA130 700000h–70FFFFh to 7F0000h–7FFFFFh 2 MB 16 128 8 SA131 to SA146 800000h–80FFFFh to 8F0000h–8FFFFFh 2 MB 16 128 9 SA147 to SA162 900000h–90FFFFh to 9F0000h–9FFFFFh 2 MB 16 128 10 SA163 to SA178 A00000h–A0FFFFh to AF0000h–AFFFFFh 2 MB 16 128 11 SA179 to SA194 B00000h–B0FFFFh to BF0000h–BFFFFFh 2 MB 16 128 12 SA195 to SA210 C00000h–C0FFFFh to CF0000h–CFFFFFh 2 MB 16 128 13 SA211 to SA226 D00000h–D0FFFFh to DF0000h–DFFFFFh 2 MB 16 128 14 SA227 to SA242 E00000h–E0FFFFh to EF0000h–EFFFFFh 15 128 SA243 to SA257 F00000h–F0FFFFh to FE0000h–FEFFFFh SA258 FF0000h–FF3FFFh 2 MB 4 32 15 SA259 FF4000h–FF7FFFh SA260 FF8000h–FFBFFFh SA261 FFC000h–FFFFFFh Notes Contains four smaller sectors at bottom of addressable memory. All 128 KB sectors. Pattern for sector address range is xx0000h–xxFFFFh. (see note) Contains four smaller sectors at top of addressable memory. Note: This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA005–SA017) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 KB sectors have the pattern xx00000h–xxFFFFh. 16 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Table 6.2. Bank Size Sector Count Sector Size (KB) Bank 32 1 MB 4 32 32 0 32 S29WS128N Sector & Memory Address Map Sector/ Sector Range Address Range SA000 000000h–003FFFh SA001 004000h–007FFFh SA002 008000h–00BFFFh SA003 00C000h–00FFFFh SA004 to SA010 010000h–01FFFFh to 070000h–07FFFFh 7 128 1 MB 8 128 1 SA011 to SA018 080000h–08FFFFh to 0F0000h–0FFFFFh 1 MB 8 128 2 SA019 to SA026 100000h–10FFFFh to 170000h–17FFFFh 1 MB 8 128 3 SA027 to SA034 180000h–18FFFFh to 1F0000h–1FFFFFh 1 MB 8 128 4 SA035 to SA042 200000h–20FFFFh to 270000h–27FFFFh 1 MB 8 128 5 SA043 to SA050 280000h–28FFFFh to 2F0000h–2FFFFFh 1 MB 8 128 6 SA051 to SA058 300000h–30FFFFh to 370000h–37FFFFh 1 MB 8 128 7 SA059 to SA066 380000h–38FFFFh to 3F0000h–3FFFFFh 1 MB 8 128 8 SA067 to SA074 400000h–40FFFFh to 470000h–47FFFFh 1 MB 8 128 9 SA075 to SA082 480000h–48FFFFh to 4F0000h–4FFFFFh 1 MB 8 128 10 SA083 to SA090 500000h–50FFFFh to 570000h–57FFFFh 1 MB 8 128 11 SA091 to SA098 580000h–58FFFFh to 5F0000h–5FFFFFh 1 MB 8 128 12 SA099 to SA106 600000h–60FFFFh to 670000h–67FFFFh 1 MB 8 128 13 SA107 to SA114 680000h–68FFFFh to 6F0000h–6FFFFFh 1 MB 8 128 14 SA115 to SA122 700000h–70FFFFh to 770000h–77FFFFh 7 128 SA123 to SA129 780000h–78FFFFh to 7E0000h–7EFFFFh 32 SA130 7F0000h–7F3FFFh SA131 7F4000h–7F7FFFh 32 SA132 7F8000h–7FBFFFh 32 SA133 7FC000h–7FFFFFh 1 MB 4 32 15 Notes Contains four smaller sectors at bottom of addressable memory. All 128 KB sectors. Pattern for sector address range is xx0000h–xxFFFFh. (see note) Contains four smaller sectors at top of addressable memory. Note: This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA005–SA009) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 KB sectors have the pattern xx00000h–xxFFFFh. October 29, 2004 S29WSxxxN_00_F0 17 P r e l i m i n a r y Table 6.3. Bank Size Sector Count 4 Sector Size (KB) Bank 32 0 0.5 MB 3 128 S29WS064N Sector & Memory Address Map Sector/ Sector Range Address Range SA000 000000h–003FFFh SA001 004000h–007FFFh SA002 008000h–00BFFFh SA003 00C000h–00FFFFh SA004 010000h–01FFFFh SA005 020000h–02FFFFh SA006 030000h–03FFFFh 0.5 MB 4 128 1 SA007–SA010 040000h–04FFFFh to 070000h–07FFFFh 0.5 MB 4 128 2 SA011–SA014 080000h–08FFFFh to 0B0000h–0BFFFFh 0.5 MB 4 128 3 SA015–SA018 0C0000h–0CFFFFh to 0F0000h–0FFFFFh 0.5 MB 4 128 4 SA019–SA022 100000h–10FFFFh to 130000h–13FFFFh 0.5 MB 4 128 5 SA023–SA026 140000h–14FFFFh to 170000h–17FFFFh 0.5 MB 4 128 6 SA027–SA030 180000h–18FFFFh to 1B0000h–1BFFFFh 0.5 MB 4 128 7 SA031–SA034 1C0000h–1CFFFFh to 1F0000h–1FFFFFh 0.5 MB 4 128 8 SA035–SA038 200000h–20FFFFh to 230000h–23FFFFh 0.5 MB 4 128 9 SA039–SA042 240000h–24FFFFh to 270000h–27FFFFh 0.5 MB 4 128 10 SA043–SA046 280000h–28FFFFh to 2B0000h–2BFFFFh 0.5 MB 4 128 11 SA047–SA050 2C0000h–2CFFFFh to 2F0000h–2FFFFFh 0.5 MB 4 128 12 SA051–SA054 300000h–30FFFFh to 330000h–33FFFFh 0.5 MB 4 128 13 SA055–SA058 340000h–34FFFFh to 370000h–37FFFFh 0.5 MB 4 128 14 SA059–SA062 380000h–38FFFFh to 3B0000h–3BFFFFh 3 128 15 0.5 MB 4 32 SA063 3C0000h–3CFFFFh SA064 3D0000h–3DFFFFh SA065 3E0000h–3EFFFFh SA066 3F0000h–3F3FFFh SA067 3F4000h–3F7FFFh SA068 3F8000h–3FBFFFh SA069 3FC000h–3FFFFFh Notes Contains four smaller sectors at bottom of addressable memory. All 128 KB sectors. Pattern for sector address range is xx0000h–xxFFFFh. (see note) Contains four smaller sectors at top of addressable memory. Note: This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA008–SA009) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 KB sectors have the pattern xx00000h–xxFFFFh. 18 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 7 Device Operations This section describes the read, program, erase, simultaneous read/write operations, handshaking, and reset features of the Flash devices. Operations are initiated by writing specific commands or a sequence with specific address and data patterns into the command registers (see Tables 12.1 and 12.2). The command register itself does not occupy any addressable memory location; rather, it is composed of latches that store the commands, along with the address and data information needed to execute the command. The contents of the register serve as input to the internal state machine and the state machine outputs dictate the function of the device. Writing incorrect address and data values or writing them in an improper sequence may place the device in an unknown state, in which case the system must write the reset command to return the device to the reading array data mode. 7.1 Device Operation Table The device must be setup appropriately for each operation. Table 7.4 describes the required state of each control pin for any particular operation. Table 7.4. Operation Device Operations CE# OE# WE# Addresses DQ15–0 RESET# CLK AVD# Asynchronous Read - Addresses Latched L L H Addr In Data Out H X Asynchronous Read - Addresses Steady State L L H Addr In Data Out H X L Asynchronous Write L H L Addr In I/O H X L Synchronous Write L H L Addr In I/O H Standby (CE#) H X X X HIGH Z H X X Hardware Reset X X X X HIGH Z L X X Load Starting Burst Address L X H Addr In X H Advance Burst to next address with appropriate Data presented on the Data Bus L L H X Burst Data Out H H Terminate current Burst read cycle H X H X HIGH Z H X Terminate current Burst read cycle via RESET# X X H X HIGH Z L Terminate current Burst read cycle and start new Burst read cycle L X H Addr In I/O H Burst Read Operations (Synchronous) X X Legend: L = Logic 0, H = Logic 1, X = Don’t Care, I/O = Input/Output. 7.2 Asynchronous Read All memories require access time to output array data. In an asynchronous read operation, data is read from one memory location at a time. Addresses are presented to the device in random order, and the propagation delay through the device causes the data on its outputs to arrive asynchronously with the address on its inputs. The device defaults to reading array data asynchronously after device power-up or hardware reset. To read data from the memory array, the system must first assert a valid address on Amax–A0, while driving AVD# and CE# to VIL. WE# should remain at VIH. The rising edge of AVD# latches the address and data will appear on DQ15–DQ0 after address access time (tACC), which is equal to the delay from stable addresses to valid output data. The chip enable October 29, 2004 S29WSxxxN_00_F0 19 P r e l i m i n a r y access time (tCE) is the delay from the stable CE# to valid data at the outputs. The output enable access time (tOE) is the delay from the falling edge of OE# to valid data at the output. 7.3 Synchronous (Burst) Read Mode & Configuration Register When a series of adjacent addresses needs to be read from the device (in order from lowest to highest address), the synchronous (or burst read) mode can be used to significantly reduce the overall time needed for the device to output array data. After an initial access time required for the data from the first address location, subsequent data is output synchronized to a clock input provided by the system. The device offers both continuous and linear methods of burst read operation, which are discussed in subsections 7.3.1 and 7.3.2, and 7.3.3. Since the device defaults to asynchronous read mode after power-up or a hardware reset, the configuration register must be set to enable the burst read mode. Other Configuration Register settings include the number of wait states to insert before the initial word (tIACC) of each burst access, the burst mode in which to operate, and when RDY will indicate data is ready to be read. Prior to entering the burst mode, the system should first determine the configuration register settings (and read the current register settings if desired via the Read Configuration Register command sequence), and then write the configuration register command sequence. See Section 7.3.4, Configuration Register, and Table 12.1, Memory Array Commands for further details. Power-up/ Hardware Reset Asynchronous Read Mode Only Set Burst Mode Configuration Register Command for Synchronous Mode (CR15 = 0) Set Burst Mode Configuration Register Command for Asynchronous Mode (CR15 = 1) Synchronous Read Mode Only Figure 7.1. Synchronous/Asynchronous State Diagram The device outputs the initial word subject to the following operational conditions: tIACC specification: the time from the rising edge of the first clock cycle after addresses are latched to valid data on the device outputs. configuration register setting CR13–CR11: the total number of clock cycles (wait states) that occur before valid data appears on the device outputs. The effect is that tIACC is lengthened. 20 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y The device outputs subsequent words tBACC after the active edge of each successive clock cycle, which also increments the internal address counter. The device outputs burst data at this rate subject to the following operational conditions: starting address: whether the address is divisible by four (where A[1:0] is 00). A divisible-by-four address incurs the least number of additional wait states that occur after the initial word. The number of additional wait states required increases for burst operations in which the starting address is one, two, or three locations above the divisible-by-four address (i.e., where A[1:0] is 01, 10, or 11). boundary crossing: a physical aspect of the device that exists every 128 words, starting at address 00007Fh. Higher operational speeds require one additional wait state. Refer to Tables 7.10–7.13 for details. Figure 11.20 shows the effects of boundary crossings at higher frequencies. clock frequency: the speed at which the device is expected to burst data. Higher speeds require additional wait states after the initial word for proper operation. Tables 7.7–7.13 show the effects of frequency on burst operation. In all cases, with or without latency, the RDY output indicates when the next data is available to be read. Table 7.5 shows the latency that occurs in the S29WS256N device when (x indicates the recommended number of wait states for various operating frequencies, as shown in Table 7.15, configuration register bits CR13-CR11). Tables 7.7–7.9 show the effects of various combinations of the starting address, operating frequency, and wait state setting (configuration register bits CR13–CR11) for the S29WS128N and S29WS064N devices. Tables 7.10–7.13 includes the wait state that occurs when crossing the internal boundary. Table 7.5. Address Latency for x Wait States (≤ 80 MHz, WS256N only) Word Wait States 0 x ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 x ws D1 D2 D3 1 ws D4 D5 D6 D7 D8 2 x ws D2 D3 1 ws 1 ws D4 D5 D6 D7 D8 3 x ws D3 1 ws 1 ws 1 ws D4 D5 D6 D7 D8 Table 7.6. Cycle Address Latency for 6 Wait States (≤ 80 MHz) Word Wait States 0 6 ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 6 ws D1 D2 D3 1 ws D4 D5 D6 D7 D8 2 6 ws D2 D3 1 ws 1 ws D4 D5 D6 D7 D8 3 6 ws D3 1 ws 1 ws 1 ws D4 D5 D6 D7 D8 Table 7.7. Cycle Address Latency for 5 Wait States (≤ 68 MHz) Word Wait States 0 5 ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 5 ws D1 D2 D3 D4 D5 D6 D7 D8 D9 2 5 ws D2 D3 1 ws D4 D5 D6 D7 D8 D9 3 5 ws D3 1 ws 1 ws D4 D5 D6 D7 D8 D9 October 29, 2004 S29WSxxxN_00_F0 Cycle 21 P r e l i m i n a r y Table 7.8. Word Wait States 0 4 ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 4 ws D1 D2 D3 D4 D5 D6 D7 D8 D9 2 4 ws D2 D3 D4 D5 D6 D7 D8 D9 D10 3 4 ws D3 1 ws D4 D5 D6 D7 D8 D9 D10 Table 7.9. Cycle Address Latency for 3 Wait States (≤ 40 MHz) Word Wait States 0 3 ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 3 ws D1 D2 D3 D4 D5 D6 D7 D8 D9 2 3 ws D2 D3 D4 D5 D6 D7 D8 D9 D10 3 3 ws D3 D4 D5 D6 D7 D8 D9 D10 D11 Table 7.10. Cycle Address/Boundary Crossing Latency for 6 Wait States (≤ 80 MHz) Word Wait States 0 6 ws D0 D1 D2 D3 1 ws D4 D5 D6 D7 1 6 ws D1 D2 D3 1 ws 1 ws D4 D5 D6 D7 2 6 ws D2 D3 1 ws 1 ws 1 ws D4 D5 D6 D7 3 6 ws D3 1 ws 1 ws 1 ws 1 ws D4 D5 D6 D7 Table 7.11. Cycle Address/Boundary Crossing Latency for 5 Wait States (≤ 68 MHz) Word Wait States 0 5 ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 5 ws D1 D2 D3 1 ws D4 D5 D6 D7 D8 2 5 ws D2 D3 1 ws 1 ws D4 D5 D6 D7 D8 3 5 ws D3 1 ws 1 ws 1 ws D4 D5 D6 D7 D8 Table 7.12. Cycle Address/Boundary Crossing Latency for 4 Wait States (≤ 54 MHz) Word Wait States 0 4 ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 4 ws D1 D2 D3 D4 D5 D6 D7 D8 D9 2 4 ws D2 D3 1 ws D4 D5 D6 D7 D8 D9 3 4 ws D3 1 ws 1 ws D4 D5 D6 D7 D8 D9 Table 7.13. 22 Address Latency for 4 Wait States (≤ 54 MHz) Cycle Address/Boundary Crossing Latency for 3 Wait States (≤ 40 MHz) Word Wait States Cycle 0 3 ws D0 D1 D2 D3 D4 D5 D6 D7 D8 1 3 ws D1 D2 D3 D4 D5 D6 D7 D8 D9 2 3 ws D2 D3 D4 D5 D6 D7 D8 D9 D10 3 3 ws D3 1 ws D4 D5 D6 D7 D8 D9 D10 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Write Set Configuration Register Command and Settings: Address 555h, Data D0h Address X00h, Data CR Load Initial Address Address = RA Wait tIACC + Programmable Wait State Setting Read Initial Data RD = DQ[15:0] Wait X Clocks: Additional Latency Due to Starting Address, Clock Frequency, and Boundary Crossing Unlock Cycle 1 Unlock Cycle 2 Command Cycle CR = Configuration Register Bits CR15-CR0 RA = Read Address CR13-CR11 sets initial access time (from address latched to valid data) from 2 to 7 clock cycles RD = Read Data See Tables 7.6–7.13 to determine total number of clocks required for X. Read Next Data RD = DQ[15:0] Delay X Clocks Yes Crossing Boundary? No End of Data? Yes Completed Figure 7.2. Synchronous Read 7.3.1 Continuous Burst Read Mode In the continuous burst read mode, the device outputs sequential burst data from the starting address given and then wrap around to address 000000h when it reaches the highest addressable memory location. The burst read mode will continue until the system drives CE# high, RESET# low, or AVD# low in conjunction with a new address. If the address being read crosses a 128-word line boundary and the subsequent word line is not programming or erasing, additional latency cycles are required as shown in Tables 7.10– 7.13. If the address crosses a bank boundary while the subsequent bank is programming or erasing, the device will provide read status information and the clock will be ignored. Upon completion of status read or program or erase operation, the host can restart a burst read operation using a new address and AVD# pulse. October 29, 2004 S29WSxxxN_00_F0 23 P r e l i m i n a r y 7.3.2 8-, 16-, 32-Word Linear Burst Read with Wrap Around In a linear burst read operation, a fixed number of words (8, 16, or 32 words) are read from consecutive addresses that are determined by the group within which the starting address falls. The groups are sized according to the number of words read in a single burst sequence for a given mode (see Table 7.14). For example, if the starting address in the 8-word mode is 3Ch, the address range to be read would be 38-3Fh, and the burst sequence would be 3C-3D-3E-3F-38-39-3A-3Bh. Thus, the device outputs all words in that burst address group until all word are read, regardless of where the starting address occurs in the address group, and then terminates the burst read. In a similar fashion, the 16-word and 32-word Linear Wrap modes begin their burst sequence on the starting address written to the device, then wrap back to the first address in the selected address group. Note that in this mode the address pointer does not cross the boundary that occurs every 128 words; thus, no wait states are inserted (except during the initial access). Table 7.14. 7.3.3 Burst Address Groups Mode Group Size Group Address Ranges 8-word 8 words 0-7h, 8-Fh, 10-17h,... 16-word 16 words 0-Fh, 10-1Fh, 20-2Fh,... 32-word 32 words 00-1Fh, 20-3Fh, 40-5Fh,... 8-, 16-, 32-Word Linear Burst without Wrap Around If wrap around is not enabled for linear burst read operations, the 8-word, 16-word, or 32word burst will execute up to the maximum memory address of the selected number of words. The burst will stop after 8, 16, or 32 addresses and will not wrap around to the first address of the selected group. For example, if the starting address in the 8- word mode is 3Ch, the address range to be read would be 39-40h, and the burst sequence would be 3C-3D-3E-3F-40-41-42-43h if wrap around is not enabled. The next address to be read will require a new address and AVD# pulse. Note that in this burst read mode, the address pointer may cross the boundary that occurs every 128 words. 7.3.4 Configuration Register The configuration register sets various operational features, most of which are associated with burst mode. Upon power-up or hardware reset, the device defaults to the asynchronous read mode, and the configuration register settings are in their default state. The host system should determine the proper settings for the entire configuration register, and then execute the Set Configuration Register command sequence, before attempting burst operations. The configuration register is not reset after deasserting CE#. The Configuration Register can also be read using a command sequence (see Table 12.1). The following list describes the register settings. 24 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Table 7.15. CR Bit Function CR15 Set Device Read Mode CR14 Boundary Crossing Configuration Register Settings (Binary) 0 = Synchronous Read (Burst Mode) Enabled 1 = Asynchronous Read Mode (default) Enabled 0 = No extra boundary crossing latency 1 = With extra boundary crossing latency (default) Must be set to “1” at higher operating frequencies. See Tables 7.10–7.13. 000 = Data valid on 2nd active CLK edge after addresses latched 001 = Data valid on 3rd active CLK edge after addresses latched 010 = Data valid on 4th active CLK edge after addresses latched (recommended for 54 MHz) 011 = Data valid on 5th active CLK edge after addresses latched (recommended for 66 MHz) 100 = Data valid on 6th active CLK edge after addresses latched (recommended for 80 MHz) 101 = Data valid on 7th active CLK edge after addresses latched (default) 110 = Reserved 111 = Reserved Inserts wait states before initial data is available. Setting greater number of wait states before initial data reduces latency after initial data. See Tables 7.6–7.13. CR13 CR12 CR11 Programmable Wait State CR10 RDY Polarity CR9 Reserved CR8 RDY CR7 Reserved 1 = default CR6 Reserved 1 = default CR5 Reserved 0 = default CR4 Reserved 0 = default CR3 Burst Wrap Around CR2 CR1 CR0 Burst Length 0 = RDY signal active low 1 = RDY signal active high (default) 1 = default 0 = RDY active one clock cycle before data 1 = RDY active with data (default) When CR13-CR11 are set to 000, RDY will be active with data regardless of CR8 setting. 0 = No Wrap Around Burst 1 = Wrap Around Burst (default) 000 = Continuous (default) 010 = 8-Word Linear Burst 011 = 16-Word Linear Burst 100 = 32-Word Linear Burst (All other bit settings are reserved) Note: Configuration Register will be in the default state upon power-up or hardware reset. Reading the Configuration Table. The configuration register can be read with a four-cycle command sequence. See Table 12.1 for sequence details. Once the data has been read from the configuration register, a software reset command is required to set the device into the correct state. 7.4 Autoselect The Autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output from the internal register (separate from the memory array) on DQ15-DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. The Autoselect codes can also be accessed in-system. When verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Tables 7.17 to 7.16). The remaining address bits are don't care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ15-DQ0. The Autoselect codes can also be accessed in-system through the command register. Note that if a Bank Address (BA) on the four uppermost address bits is asserted during the third write cycle of the Autoselect command, the host system can read Autoselect data from that bank and then immediately read array data from the other bank, without exiting the Autoselect mode. October 29, 2004 S29WSxxxN_00_F0 25 P r e l i m i n a r y To access the Autoselect codes, the host system must issue the Autoselect command. The Autoselect command sequence may be written to an address within a bank that is either in the read or erase-suspend-read mode. The Autoselect command may not be written while the device is actively programming or erasing in the other bank. Autoselect does not support simultaneous operations or burst mode. The system must write the reset command to return to the read mode (or erase-suspendread mode if the bank was previously in Erase Suspend). See Table 12.1 for command sequence details. Table 7.16. Description Autoselect Addresses Address Read Data Manufacturer ID (BA) + 00h 0001h Device ID, Word 1 (BA) + 01h 227Eh Device ID, Word 2 (BA) + 0Eh 2230 (WS256N) 2231 (WS128N) 2232 (WS064N) Device ID, Word 3 (BA) + 0Fh 2200 DQ15 - DQ8 = Reserved DQ7 (Factory Lock Bit): 1 = Locked, 0 = Not Locked DQ6 (Customer Lock Bit): 1 = Locked, 0 = Not Locked DQ5 (Handshake Bit): 1 = Reserved, 0 = Standard Handshake Indicator Bits (See Note) (BA) + 03h DQ4, DQ3 (WP# Protection Boot Code): 00 = WP# Protects both Top Boot and Bottom Boot Sectors. 01, 10, 11 = Reserved DQ2 = Reserved DQ1 (DYB Power up State [Lock Register DQ4]): 1 = Unlocked (user option), 0 = Locked (default) DQ0 (PPB Eraseability [Lock Register DQ3]): 1 = Erase allowed, 0 = Erase disabled Sector Block Lock/ Unlock (SA) + 02h 0001h = Locked, 0000h = Unlocked Note: For WS128N and WS064, DQ1 and DQ0 will be reserved. Software Functions and Sample Code Table 7.17. Autoselect Entry (LLD Function = lld_AutoselectEntryCmd) 26 Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write BAxAAAh BAx555h 0x00AAh Unlock Cycle 2 Write BAx555h BAx2AAh 0x0055h Autoselect Command Write BAxAAAh BAx555h 0x0090h S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Table 7.18. Autoselect Exit (LLD Function = lld_AutoselectExitCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write base + XXXh base + XXXh 0x00F0h Notes: 1. Any offset within the device will work. 2. BA = Bank Address. The bank address is required. 3. base = base address. The following is a C source code example of using the autoselect function to read the manufacturer ID. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Here is an example of Autoselect mode (getting manufacturer ID) */ /* Define UINT16 example: typedef unsigned short UINT16; */ UINT16 manuf_id; /* Auto Select Entry */ *( (UINT16 *)bank_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)bank_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)bank_addr + 0x555 ) = 0x0090; /* write autoselect command */ /* multiple reads can be performed after entry */ manuf_id = *( (UINT16 *)bank_addr + 0x000 ); /* read manuf. id */ /* Autoselect exit */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* exit autoselect (write reset command) */ October 29, 2004 S29WSxxxN_00_F0 27 P r e l i m i n a r y 7.5 Program/Erase Operations These devices are capable of several modes of programming and or erase operations which are described in details during the following sections. However, prior to any programming and or erase operation, devices must be setup appropriately as outlined in Table 6.4. During a synchronous write operation, to write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive AVD# and CE# to VIL, and OE# to VIH when providing an address to the device, and drive WE# and CE# to VIL, and OE# to VIH when writing commands or data. During an asynchronous write operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing an address, command, and data. Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st rising edge of WE# or CE#. Note the following: When the Embedded Program algorithm is complete, the device then returns to the read mode. The system can determine the status of the program operation by using DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits. A “0” cannot be programmed back to a “1.” Attempting to do so will cause the device to set DQ5 = 1 (halting any further operation and requiring a reset command). A succeeding read will show that the data is still “0.” Only erase operations can convert a “0” to a “1.” Any commands written to the device during the Embedded Program Algorithm are ignored except the Program Suspend command. SecSi Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress. A hardware reset immediately terminates the program operation and the program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries for single word programming operation. Programming to the same word address multiple times without intervening erases is limited. For such application requirements, please contact your local Spansion representative. 7.5.1. Single Word Programming Single word programming mode is the simplest method of programming. In this mode, four Flash command write cycles are used to program an individual Flash address. The data for this programming operation could be 8-, 16- or 32-bits wide. While this method is supported by all Spansion devices, in general it is not recommended for devices that support Write Buffer Programming. See Table 12.1 for the required bus cycles and Figure 7.19 for the flowchart. When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits. During programming, any command (except the Suspend Program command) is ignored. The SecSi Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress. 28 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y A hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Programming to the same address multiple times continuously (for example, “walking” a bit within a word) for an extended period is not recommended. For more information, contact your local sales office. Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Program Command: Address 555h, Data A0h Setup Command Program Address (PA), Program Data (PD) Program Data to Address: PA, PD Perform Polling Algorithm (see Write Operation Status flowchart) Polling Status = Busy? Yes No Yes Polling Status = Done? No PASS. Device is in read mode. Figure 7.19. October 29, 2004 S29WSxxxN_00_F0 Error condition (Exceeded Timing Limits) FAIL. Issue reset command to return to read array mode. Single Word Program 29 P r e l i m i n a r y Software Functions and Sample Code Table 7.20. Single Word Program (LLD Function = lld_ProgramCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Base + AAAh Base + 555h 00AAh Unlock Cycle 2 Write Base + 554h Base + 2AAh 0055h Program Setup Write Base + AAAh Base + 555h 00A0h Program Write Word Address Word Address Data Word Note: Base = Base Address. The following is a C source code example of using the single word program function. Refer to t he S pans io n Lo w Lev el Driver U s er ’s Gu ide ( avail able on www.am d.c o m a nd www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program Command */ *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)pa ) /* Poll for program completion */ = = = = 0x00AA; 0x0055; 0x00A0; data; /* /* /* /* write write write write unlock cycle 1 unlock cycle 2 program setup command data to be programmed */ */ */ */ 7.5.2 Write Buffer Programming Write Buffer Programming allows the system to write a maximum of 32 words in one programming operation. This results in a faster effective word programming time than the standard “word” programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming will occur. At this point, the system writes the number of “word locations minus 1” that will be loaded into the page buffer at the Sector Address in which programming will occur. This tells the device how many write buffer addresses will be loaded with data and therefore when to expect the “Program Buffer to Flash” confirm command. The number of locations to program cannot exceed the size of the write buffer or the operation will abort. (Number loaded = the number of locations to program minus 1. For example, if the system will program 6 address locations, then 05h should be written to the device.) The system then writes the starting address/data combination. This starting address is the first address/data pair to be programmed, and selects the “write-buffer-page” address. All subsequent address/data pairs must fall within the elected-write-buffer-page. The “write-buffer-page” is selected by using the addresses AMAX - A5. The “write-buffer-page” addresses must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple “write-buffer-pages.” This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected “write-buffer-page”, the operation will ABORT.) After writing the Starting Address/Data pair, the system then writes the remaining address/ data pairs into the write buffer. Note that if a Write Buffer address location is loaded multiple times, the “address/data pair” counter will be decremented for every data load operation. Also, the last data loaded at a location before the “Program Buffer to Flash” confirm command will be programmed into the 30 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y device. It is the software's responsibility to comprehend ramifications of loading a write-buffer location more than once. The counter decrements for each data load operation, NOT for each unique write-buffer-address location. Once the specified number of write buffer locations have been loaded, the system must then write the “Program Buffer to Flash” command at the Sector Address. Any other address/data write combinations will abort the Write Buffer Programming operation. The device will then “go busy.” The Data Bar polling techniques should be used while monitoring the last address location loaded into the write buffer. This eliminates the need to store an address in memory because the system can load the last address location, issue the program confirm command at the last loaded address location, and then data bar poll at that same address. DQ7, DQ6, DQ5, DQ2, and DQ1 should be monitored to determine the device status during Write Buffer Programming. The write-buffer “embedded” programming operation can be suspended using the standard suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device will return to READ mode. The Write Buffer Programming Sequence is ABORTED under any of the following conditions: Load a value that is greater than the page buffer size during the “Number of Locations to Program” step. Write to an address in a sector different than the one specified during the Write-BufferLoad command. Write an Address/Data pair to a different write-buffer-page than the one selected by the “Starting Address” during the “write buffer data loading” stage of the operation. Write data other than the “Confirm Command” after the specified number of “data load” cycles. The ABORT condition is indicated by DQ1 = 1, DQ7 = DATA# (for the “last address location loaded”), DQ6 = TOGGLE, DQ5 = 0. This indicates that the Write Buffer Programming Operation was ABORTED. A “Write-to-Buffer-Abort reset” command sequence is required when using the write buffer Programming features in Unlock Bypass mode. Note that the SecSITM sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Write buffer programming is allowed in any sequence of memory (or address) locations. These flash devices are capable of handling multiple write buffer programming operations on the same write buffer address range without intervening erases. However, programming the same word address multiple times without intervening erases requires a modified programming method. Please contact your local SpansionTM representative for details. Use of the write buffer is strongly recommended for programming when multiple words are to be programmed. Write buffer programming is approximately eight times faster than programming one word at a time. October 29, 2004 S29WSxxxN_00_F0 31 P r e l i m i n a r y Software Functions and Sample Code Table 7.21. Write Buffer Program (LLD Functions Used = lld_WriteToBufferCmd, lld_ProgramBufferToFlashCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write Base + AAAh Base + 555h 00AAh 2 Unlock Write Base + 554h Base + 2AAh 0055h 3 Write Buffer Load Command Write Program Address 0025h 4 Write Word Count Write Program Address Word Count (N–1)h Number of words (N) loaded into the write buffer can be from 1 to 32 words. 5 to 36 Load Buffer Word N Write Program Address, Word N Word N Last Write Buffer to Flash Write Sector Address 0029h Notes: 1. Base = Base Address. 2. Last = Last cycle of write buffer program operation; depending on number of words written, the total number of cycles may be from 6 to 37. 3. For maximum efficiency, it is recommended that the write buffer be loaded with the highest number of words (N words) possible. The following is a C source code example of using the write buffer program function. Refer to t he S pans io n Lo w Lev el Driver U s er ’s Gu ide ( avail able on www.am d.c o m a nd www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Write Buffer Programming Command */ /* NOTES: Write buffer programming limited to 16 words. */ /* All addresses to be written to the flash in */ /* one operation must be within the same flash */ /* page. A flash page begins at addresses */ /* evenly divisible by 0x20. */ UINT16 *src = source_of_data; /* address of source data */ UINT16 *dst = destination_of_data; /* flash destination address */ UINT16 wc = words_to_program -1; /* word count (minus 1) */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)sector_address ) = 0x0025; /* write write buffer load command */ *( (UINT16 *)sector_address ) = wc; /* write word count (minus 1) */ loop: *dst = *src; /* ALL dst MUST BE SAME PAGE */ /* write source data to destination */ dst++; /* increment destination pointer */ src++; /* increment source pointer */ if (wc == 0) goto confirm /* done when word count equals zero */ wc--; /* decrement word count */ goto loop; /* do it again */ confirm: *( (UINT16 *)sector_address ) = 0x0029; /* write confirm command */ /* poll for completion */ /* Example: Write Buffer Abort Reset */ *( (UINT16 *)addr + 0x555 ) = 0x00AA; *( (UINT16 *)addr + 0x2AA ) = 0x0055; *( (UINT16 *)addr + 0x555 ) = 0x00F0; 32 /* write unlock cycle 1 /* write unlock cycle 2 /* write buffer abort reset */ */ */ S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Issue Write Buffer Load Command: Address 555h, Data 25h Load Word Count to Program Program Data to Address: SA = wc wc = number of words – 1 Yes Confirm command: SA 29h wc = 0? No Wait 4 µs Write Next Word, Decrement wc: PA data , wc = wc – 1 No Write Buffer Abort Desired? Perform Polling Algorithm (see Write Operation Status flowchart) Yes Write to a Different Sector Address to Cause Write Buffer Abort Polling Status = Done? Yes No No Yes Write Buffer Abort? Error? Yes No RESET. Issue Write Buffer Abort Reset Command Figure 7.22. FAIL. Issue reset command to return to read array mode. PASS. Device is in read mode. Write Buffer Programming Operation 7.5.3 Sector Erase The sector erase function erases one or more sectors in the memory array. (See Table 12.1, Memory Array Commands; and Figure 7.24, Sector Erase Operation.) The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of no less than tSEA occurs. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of October 29, 2004 S29WSxxxN_00_F0 33 P r e l i m i n a r y sectors may be from one sector to all sectors. The time between these additional cycles must be less than tSEA. Any sector erase address and command following the exceeded time-out (tSEA) may or may not be accepted. Any command other than Sector Erase or Erase Suspend during the time-out period resets that bank to the read mode. The system can monitor DQ3 to determine if the sector erase timer has timed out (See the “DQ3: Sector Erase Timer” section.) The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the bank returns to reading array data and addresses are no longer latched. Note that while the Embedded Erase operation is in progress, the system can read data from the non-erasing banks. The system can determine the status of the erase operation by reading DQ7 or DQ6/DQ2 in the erasing bank. Refer to “Write Operation Status” for information on these status bits. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once that bank has returned to reading array data, to ensure data integrity. Figure 7.24 illustrates the algorithm for the erase operation. Refer to the “Erase/Program Operations” section for parameters and timing diagrams. 34 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Software Functions and Sample Code Table 7.23. Sector Erase (LLD Function = lld_SectorEraseCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write Base + AAAh Base + 555h 00AAh 2 Unlock Write Base + 554h Base + 2AAh 0055h 3 Setup Command Write Base + AAAh Base + 555h 0080h 4 Unlock Write Base + AAAh Base + 555h 00AAh 5 Unlock Write Base + 554h Base + 2AAh 0055h 6 Sector Erase Command Write Sector Address Sector Address 0030h Unlimited additional sectors may be selected for erase; command(s) must be written within tSEA. The following is a C source code example of using the sector erase function. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Sector Erase Command *( (UINT16 *)base_addr + 0x555 *( (UINT16 *)base_addr + 0x2AA *( (UINT16 *)base_addr + 0x555 *( (UINT16 *)base_addr + 0x555 *( (UINT16 *)base_addr + 0x2AA *( (UINT16 *)sector_address ) October 29, 2004 S29WSxxxN_00_F0 */ ) = ) = ) = ) = ) = = 0x00AA; 0x0055; 0x0080; 0x00AA; 0x0055; 0x0030; /* /* /* /* /* /* write write write write write write unlock cycle 1 */ unlock cycle 2 */ setup command */ additional unlock cycle 1 */ additional unlock cycle 2 */ sector erase command */ 35 P r e l i m i n a r y Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Sector Erase Cycles: Address 555h, Data 80h Address 555h, Data AAh Address 2AAh, Data 55h Sector Address, Data 30h Command Cycle 1 Command Cycle 2 Command Cycle 3 Specify first sector for erasure Select Additional Sectors? No Yes Write Additional Sector Addresses • Each additional cycle must be written within tSEA timeout • Timeout resets after each additional cycle is written • The host system may monitor DQ3 or wait tSEA to ensure acceptance of erase commands No Yes Poll DQ3. DQ3 = 1? Last Sector Selected? • No limit on number of sectors • Commands other than Erase Suspend or selecting additional sectors for erasure during timeout reset device to reading array data No Yes Wait 4 µs Perform Write Operation Status Algorithm (see Figure 7.33) Yes Status may be obtained by reading DQ7, DQ6 and/or DQ2. Done? No DQ5 = 1? No Error condition (Exceeded Timing Limits) Yes PASS. Device returns to reading array. FAIL. Write reset command to return to reading array. Notes: 1. 2. See Table 12.1 for erase command sequence. See the section on DQ3 for information on the sector erase timeout. Figure 7.24. 36 Sector Erase Operation S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 7.5.4 Chip Erase Command Sequence Chip erase is a six-bus cycle operation as indicated by Table 12.1. These commands invoke the Embedded Erase algorithm, which does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. The “Command Definition” section in the appendix shows the address and data requirements for the chip erase command sequence. When the Embedded Erase algorithm is complete, that bank returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7 or DQ6/DQ2. Refer to “Write Operation Status” for information on these status bits. Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once that bank has returned to reading array data, to ensure data integrity. Software Functions and Sample Code Table 7.25. Chip Erase (LLD Function = lld_ChipEraseCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write Base + AAAh Base + 555h 00AAh 2 Unlock Write Base + 554h Base + 2AAh 0055h 3 Setup Command Write Base + AAAh Base + 555h 0080h 4 Unlock Write Base + AAAh Base + 555h 00AAh 5 Unlock Write Base + 554h Base + 2AAh 0055h 6 Chip Erase Command Write Base + AAAh Base + 555h 0010h The following is a C source code example of using the chip erase function. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Chip Erase Command */ /* Note: Cannot be suspended */ *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x000 ) = = = = = = 0x00AA; 0x0055; 0x0080; 0x00AA; 0x0055; 0x0010; /* /* /* /* /* /* write write write write write write unlock cycle 1 */ unlock cycle 2 */ setup command */ additional unlock cycle 1 */ additional unlock cycle 2 */ chip erase command */ 7.5.5 Erase Suspend/Erase Resume Commands The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. The bank address is required when writing this command. This command is valid only during the sector erase operation, including the minimum tSEA time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of tESL (erase suspend latency) to suspend the erase operation. How- October 29, 2004 S29WSxxxN_00_F0 37 P r e l i m i n a r y ever, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation has been suspended, the bank enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7-DQ0. The system can use DQ7, or DQ6, and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to Table 7.35 for information on these status bits. After an erase-suspended program operation is complete, the bank returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. In the erase-suspend-read mode, the system can also issue the Autoselect command sequence. Refer to the “Write Buffer Programming Operation” section and the “Autoselect Command Sequence” section for details. To resume the sector erase operation, the system must write the Erase Resume command. The bank address of the erase-suspended bank is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. Software Functions and Sample Code Table 7.26. Erase Suspend (LLD Function = lld_EraseSuspendCmd) Cycle Operation Byte Address Word Address Data 1 Write Bank Address Bank Address 00B0h The following is a C source code example of using the erase suspend function. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase suspend command */ *( (UINT16 *)bank_addr + 0x000 ) = 0x00B0; /* write suspend command Table 7.27. */ Erase Resume (LLD Function = lld_EraseResumeCmd) Cycle Operation Byte Address Word Address Data 1 Write Bank Address Bank Address 0030h The following is a C source code example of using the erase resume function. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase resume command */ *( (UINT16 *)bank_addr + 0x000 ) = 0x0030; /* write resume command /* The flash needs adequate time in the resume state */ */ 7.5.6 Program Suspend/Program Resume Commands The Program Suspend command allows the system to interrupt an embedded programming operation or a “Write to Buffer” programming operation so that data can read from any nonsuspended sector. When the Program Suspend command is written during a programming process, the device halts the programming operation within tPSL (program suspend latency) 38 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y and updates the status bits. Addresses are “don't-cares” when writing the Program Suspend command. After the programming operation has been suspended, the system can read array data from any non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the SecSi Sector area, then user must use the proper command sequences to enter and exit this region. The system may also write the Autoselect command sequence when the device is in Program Suspend mode. The device allows reading Autoselect codes in the suspended sectors, since the codes are not stored in the memory array. When the device exits the Autoselect mode, the device reverts to Program Suspend mode, and is ready for another valid operation. See “Autoselect Command Sequence” for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See “Write Operation Status” for more information. The system must write the Program Resume command (address bits are “don't care”) to exit the Program Suspend mode and continue the programming operation. Further writes of the Program Resume command are ignored. Another Program Suspend command can be written after the device has resumed programming. Software Functions and Sample Code Table 7.28. Program Suspend (LLD Function = lld_ProgramSuspendCmd) Cycle Operation Byte Address Word Address Data 1 Write Bank Address Bank Address 00B0h The following is a C source code example of using the program suspend function. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program suspend command */ *( (UINT16 *)base_addr + 0x000 ) = 0x00B0; Table 7.29. /* write suspend command */ Program Resume (LLD Function = lld_ProgramResumeCmd) Cycle Operation Byte Address Word Address Data 1 Write Bank Address Bank Address 0030h The following is a C source code example of using the program resume function. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program resume command */ *( (UINT16 *)base_addr + 0x000 ) = 0x0030; /* write resume command */ 7.5.7 Accelerated Program/Chip Erase Accelerated single word programming, write buffer programming, sector erase, and chip erase operations are enabled through the ACC function. This method is faster than the standard chip program and erase command sequences. October 29, 2004 S29WSxxxN_00_F0 39 P r e l i m i n a r y The accelerated chip program and erase functions must not be used more than 10 times per sector. In addition, accelerated chip program and erase should be performed at room temperature (25°C ±10°C). If the system asserts VHH on this input, the device automatically enters the aforementioned Unlock Bypass mode and uses the higher voltage on the input to reduce the time required for program and erase operations. The system can then use the Write Buffer Load command sequence provided by the Unlock Bypass mode. Note that if a “Write-to-Buffer-Abort Reset” is required while in Unlock Bypass mode, the full 3-cycle RESET command sequence must be used to reset the device. Removing VHH from the ACC input, upon completion of the embedded program or erase operation, returns the device to normal operation. Sectors must be unlocked prior to raising ACC to VHH. The ACC pin must not be at VHH for operations other than accelerated programming and accelerated chip erase, or device damage may result. The ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. tACC locks all sector if set to VIL; tACC should be set to VIH for all other conditions. 7.5.8 Unlock Bypass The device features an Unlock Bypass mode to facilitate faster word programming. Once the device enters the Unlock Bypass mode, only two write cycles are required to program data, instead of the normal four cycles. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. The “Command Definition Summary” section shows the requirements for the unlock bypass command sequences. During the unlock bypass mode, only the Read, Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the twocycle unlock bypass reset command sequence. The first cycle must contain the bank address and the data 90h. The second cycle need only contain the data 00h. The bank then returns to the read mode. Software Functions and Sample Code The following are C source code examples of using the unlock bypass entry, program, and exit functions. Refer to the Spansion Low Level Driver User’s Guide (available soon on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. Table 7.30. Unlock Bypass Entry (LLD Function = lld_UnlockBypassEntryCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write Base + AAAh Base + 555h 00AAh 2 Unlock Write Base + 554h Base + 2AAh 0055h 3 Entry Command Write Base + AAAh Base + 555h 0020h /* Example: Unlock Bypass Entry Command */ *( (UINT16 *)bank_addr + 0x555 ) = 0x00AA; /* write unlock *( (UINT16 *)bank_addr + 0x2AA ) = 0x0055; /* write unlock *( (UINT16 *)bank_addr + 0x555 ) = 0x0020; /* write unlock /* At this point, programming only takes two write cycles. /* Once you enter Unlock Bypass Mode, do a series of like /* operations (programming or sector erase) and then exit /* Unlock Bypass Mode before beginning a different type of /* operations. 40 cycle 1 cycle 2 bypass command */ */ */ */ */ */ */ */ S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Table 7.31. Unlock Bypass Program (LLD Function = lld_UnlockBypassProgramCmd) Cycle Description Operation Byte Address Word Address Data 1 Program Setup Command Write Base + xxxh Base +xxxh 00A0h 2 Program Command Write Program Address Program Address Program Data /* Example: Unlock Bypass Program Command */ /* Do while in Unlock Bypass Entry Mode! */ *( (UINT16 *)bank_addr + 0x555 ) = 0x00A0; *( (UINT16 *)pa ) = data; /* Poll until done or error. */ /* If done and more to program, */ /* do above two cycles again. */ Table 7.32. /* write program setup command /* write data to be programmed */ */ Unlock Bypass Reset (LLD Function = lld_UnlockBypassResetCmd) Cycle Description Operation Byte Address Word Address Data 1 Reset Cycle 1 Write Base + xxxh Base +xxxh 0090h 2 Reset Cycle 2 Write Base + xxxh Base +xxxh 0000h /* Example: Unlock Bypass Exit Command */ *( (UINT16 *)base_addr + 0x000 ) = 0x0090; *( (UINT16 *)base_addr + 0x000 ) = 0x0000; 7.5.9 Write Operation Status The device provides several bits to determine the status of a program or erase operation. The following subsections describe the function of DQ1, DQ2, DQ3, DQ5, DQ6, and DQ7. DQ7: Data# Polling. The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether a bank is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. Note that the Data# Polling is valid only for the last word being programmed in the write-buffer-page during Write Buffer Programming. Reading Data# Polling status on any word other than the last word to be programmed in the write-buffer-page will return false status information. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# polling on DQ7 is active for approximately tPSP, then that bank returns to the read mode. During the Embedded Erase Algorithm, Data# polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the bank enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately tASP, then the bank returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ6-DQ0 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the October 29, 2004 S29WSxxxN_00_F0 41 P r e l i m i n a r y system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid data, the data outputs on DQ6DQ0 may be still invalid. Valid data on DQ7-D00 will appear on successive read cycles. See the following for more information: Table 7.35, Write Operation Status, shows the outputs for Data# Polling on DQ7. Figure 7.33, Write Operation Status Flowchart, shows the D a t a # P o l l i n g a l g o r i t h m ; a n d F i g u r e 1 1 . 1 6 , D a t a # Po l l i n g T i m i n g s (During Embedded Algorithm), shows the Data# Polling timing diagram. 42 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y START Read 1 (Note 6) YES Erase Operation Complete DQ7=valid data? NO Read 1 DQ5=1? YES YES Read 2 Read3= valid data? NO NO Read 3 Read 2 YES Program Operation Failed Write Buffer Programming? YES NO Programming Operation? Read 3 NO Device BUSY, Re-Poll (Note 3) (Note 1) (Note 4) (Note 1) YES DQ6 toggling? DQ6 toggling? TIMEOUT NO YES DEVICE ERROR NO Read3 DQ1=1? (Note 2) NO (Note 5) YES Device BUSY, Re-Poll DQ2 toggling? YES NO Read 2 Device BUSY, Re-Poll Erase Operation Complete Read 3 Read3 DQ1=1 AND DQ7 ≠ Valid Data? YES Device in Erase/Suspend Mode Write Buffer Operation Failed NO Notes: 1. DQ6 is toggling if Read2 DQ6 does not equal Read3 DQ6. 2. DQ2 is toggling if Read2 DQ2 does not equal Read3 DQ2. 3. May be due to an attempt to program a 0 to 1. Use the RESET command to exit operation. 4. Write buffer error if DQ1 of last read =1. 5. Invalid state, use RESET command to exit operation. 6. Valid data is the data that is intended to be programmed or all 1's for an erase operation. 7. Data polling algorithm valid for all operations except advanced sector protection. Device BUSY, Re-Poll Figure 7.33. October 29, 2004 S29WSxxxN_00_F0 Write Operation Status Flowchart 43 P r e l i m i n a r y DQ6: Toggle Bit I . Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address in the same bank, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. When the operation is complete, DQ6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately tASP [all sectors protected toggle time], then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling). If a program address falls within a protected sector, DQ6 toggles for approximately tPAP after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program Algorithm is complete. See the following for additional information: Figure 7.33, Write Operation Status Flowchart; Figure 11.17, Toggle Bit Timings (During Embedded Algorithm), and Tables 7.34 and 7.35. Toggle Bit I on DQ6 requires either OE# or CE# to be de-asserted and reasserted to show the change in state. DQ2: Toggle Bit II . The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 7.34 to compare outputs for DQ2 and DQ6. See the following for additional information: Figure 7.33, the “DQ6: Toggle Bit I” section, and Figures 11.16–11.19. 44 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Table 7.34. DQ6 and DQ2 Indications If device is and the system reads then DQ6 and DQ2 programming, at any address, toggles, does not toggle. at an address within a sector selected for erasure, toggles, also toggles. at an address within sectors not selected for erasure, toggles, does not toggle. at an address within a sector selected for erasure, does not toggle, toggles. at an address within sectors not selected for erasure, returns array data, returns array data. The system can read from any sector not selected for erasure. at any address, toggles, is not applicable. actively erasing, erase suspended, programming in erase suspend Reading Toggle Bits DQ6/DQ2. Whenever the system initially begins reading toggle bit sta- tus, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erases operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erases operation. If it is still toggling, the device did not complete the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation. Refer to Figure 7.33 for more details. DQ5: Exceeded Timing Limits. DQ5 indicates whether the program or erase time has ex- ceeded a specified internal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase cycle was not successfully completed. The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was previously programmed to “0.” Only an erase operation can change a “0” back to a “1.” Under this condition, the device halts the operation, and when the timing limit has been exceeded, DQ5 produces a “1.”Under both these conditions, the system must write the reset command to return to the read mode (or to the erase-suspend-read mode if a bank was previously in the erase-suspend-program mode). DQ3: Sector Erase Timeout State Indicator. After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be assumed to be less than tSEA, the system need not monitor DQ3. See Sector Erase Command Sequence for more details. October 29, 2004 S29WSxxxN_00_F0 45 P r e l i m i n a r y After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device will accept additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each sub-sequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 7.35 shows the status of DQ3 relative to the other status bits. DQ1: Write to Buffer Abort. DQ1 indicates whether a Write to Buffer operation was aborted. Under these conditions DQ1 produces a “1”. The system must issue the Write to Buffer Abort Reset command sequence to return the device to reading array data. See Write Buffer Programming Operation for more details. Table 7.35. DQ7 (Note 2) DQ6 DQ5 (Note 1) DQ3 DQ2 (Note 2) DQ1 (Note 4) DQ7# Toggle 0 N/A No toggle 0 0 Toggle 0 1 Toggle N/A INVALID INVALID INVALID INVALID INVALID INVALID (Not Allowed) (Not Allowed) (Not Allowed) (Not Allowed) (Not Allowed) (Not Allowed) Data Data Data Data Data Data 1 No toggle 0 N/A Toggle N/A Data Data Data Data Data Data Erase-Suspend-Program DQ7# Toggle 0 N/A N/A N/A BUSY State DQ7# Toggle 0 N/A N/A 0 Exceeded Timing Limits DQ7# Toggle 1 N/A N/A 0 ABORT State DQ7# Toggle 0 N/A N/A 1 Status Standard Mode Embedded Program Algorithm Program Suspend Mode (Note 3) Reading within Program Suspended Sector Erase Suspend Mode Write to Buffer (Note 5) Write Operation Status Embedded Erase Algorithm Reading within Non-Program Suspended Sector Erase-SuspendRead Erase Suspended Sector Non-Erase Suspended Sector Notes: 1. 2. 3. 4. 5. 46 DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. Refer to the section on DQ5 for more information. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. Data are invalid for addresses in a Program Suspended sector. DQ1 indicates the Write to Buffer ABORT status during Write Buffer Programming operations. The data-bar polling algorithm should be used for Write Buffer Programming operations. Note that DQ7# during Write Buffer Programming indicates the data-bar for DQ7 data for the LAST LOADED WRITE-BUFFER ADDRESS location. S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 7.6 Simultaneous Read/Write The simultaneous read/write feature allows the host system to read data from one bank of memory while programming or erasing another bank of memory. An erase operation may also be suspended to read from or program another location within the same bank (except the sector being erased). Figure 11.23, Back-to-Back Read/Write Cycle Timings, shows how read and write cycles may be initiated for simultaneous operation with zero latency. Refer to the DC Characteristics (CMOS Compatible) table for read-while-program and read-while-erase current specification. 7.7 Writing Commands/Command Sequences When the device is configured for Asynchronous read, only Asynchronous write operations are allowed, and CLK is ignored. When in the Synchronous read mode configuration, the device is able to perform both Asynchronous and Synchronous write operations. CLK and AVD# induced address latches are supported in the Synchronous programming mode. During a synchronous write operation, to write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive AVD# and CE# to VIL, and OE# to VIH when providing an address to the device, and drive WE# and CE# to VIL, and OE# to VIH when writing commands or data. During an asynchronous write operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing an address, command, and data. Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st rising edge of WE# or CE#. An erase operation can erase one sector, multiple sectors, or the entire device. Tables 6.1–6.3 indicate the address space that each sector occupies. The device address space is divided into sixteen banks: Banks 1 through 14 contain only 64 Kword sectors, while Banks 0 and 15 contain both 16 Kword boot sectors in addition to 64 Kword sectors. A “bank address” is the set of address bits required to uniquely select a bank. Similarly, a “sector address” is the address bits required to uniquely select a sector. ICC2 in “DC Characteristics” represents the active current specification for the write mode. “AC Characteristics-Synchronous” and “AC Characteristics-Asynchronous” contain timing specification tables and timing diagrams for write operations. 7.8 Handshaking The handshaking feature allows the host system to detect when data is ready to be read by simply monitoring the RDY (Ready) pin, which is a dedicated output and controlled by CE#. When the device is configured to operate in synchronous mode, and OE# is low (active), the initial word of burst data becomes available after either the falling or rising edge of the RDY pin (depending on the setting for bit 10 in the Configuration Register). It is recommended that the host system set CR13–CR11 in the Configuration Register to the appropriate number of wait states to ensure optimal burst mode operation (see Table 7.15, Configuration Register). Bit 8 in the Configuration Register allows the host to specify whether RDY is active at the same time that data is ready, or one cycle before data is ready. October 29, 2004 S29WSxxxN_00_F0 47 P r e l i m i n a r y 7.9 Hardware Reset The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all outputs, resets the configuration register, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. To ensure data integrity the operation that was interrupted should be reinitiated once the device is ready to accept another command sequence. When RESET# is held at VSS, the device draws CMOS standby current (ICC4). If RESET# is held at VIL, but not at VSS, the standby current will be greater. RESET# may be tied to the system reset circuitry which enables the system to read the bootup firmware from the Flash memory upon a system reset. See Figures 11.5 and 11.12 for timing diagrams. 7.10 Software Reset Software reset is part of the command set (see Table 12.1) that also returns the device to array read mode and must be used for the following conditions: 1. to exit Autoselect mode 2. when DQ5 goes high during write status operation that indicates program or erase cycle was not successfully completed 3. exit sector lock/unlock operation. 4. to return to erase-suspend-read mode if the device was previously in Erase Suspend mode. 5. after any aborted operations Software Functions and Sample Code Table 7.36. Reset (LLD Function = lld_ResetCmd) Cycle Operation Byte Address Word Address Data Reset Command Write Base + xxxh Base + xxxh 00F0h Note: Base = Base Address. The following is a C source code example of using the reset function. Refer to the Spansion Low Level Driver User’s Guide (available on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: Reset (software reset of Flash state machine) */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; The following are additional points to consider when using the reset command: This command resets the banks to the read and address bits are ignored. Reset commands are ignored once erasure has begun until the operation is complete. Once programming begins, the device ignores reset commands until the operation is complete The reset command may be written between the cycles in a program command sequence before programming begins (prior to the third cycle). This resets the bank to which the system was writing to the read mode. 48 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y If the program command sequence is written to a bank that is in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. The reset command may be also written during an Autoselect command sequence. If a bank has entered the Autoselect mode while in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. If DQ1 goes high during a Write Buffer Programming operation, the system must write the "Write to Buffer Abort Reset" command sequence to RESET the device to reading array data. The standard RESET command will not work during this condition. To exit the unlock bypass mode, the system must issue a two-cycle unlock bypass reset command sequence [see command table for details]. October 29, 2004 S29WSxxxN_00_F0 49 P r e l i m i n a r y 8 Advanced Sector Protection/Unprotection The Advanced Sector Protection/Unprotection feature disables or enables programming or erase operations in any or all sectors and can be implemented through software and/or hardware methods, which are independent of each other. This section describes the various methods of protecting data stored in the memory array. An overview of these methods in shown in Figure 8.1. Hardware Methods Software Methods Lock Register (One Time Programmable) ACC = VIL (All sectors locked) Password Method Persistent Method (DQ2) (DQ1) WP# = VIL (All boot sectors locked) 64-bit Password (One Time Protect) 1,2,3 PPB Lock Bit 0 = PPBs Locked Memory Array Persistent Protection Bit (PPB)4,5 Sector 0 PPB 0 DYB 0 Sector 1 PPB 1 DYB 1 Sector 2 PPB 2 DYB 2 Sector N-2 PPB N-2 DYB N-2 Sector N-1 PPB N-1 DYB N-1 Sector N3 PPB N DYB N 3. N = Highest Address Sector. Figure 8.1. 50 1 = PPBs Unlocked 1. Bit is volatile, and defaults to “1” on reset. 2. Programming to “0” locks all PPBs to their current state. 3. Once programmed to “0”, requires hardware reset to unlock. 4. 0 = Sector Protected, 1 = Sector Unprotected. 5. PPBs programmed individually, but cleared collectively Dynamic Protection Bit (PPB)6,7,8 6. 0 = Sector Protected, 1 = Sector Unprotected. 7. Protect effective only if PPB Lock Bit is unlocked and corresponding PPB is “1” (unprotected). 8. Volatile Bits: defaults to user choice upon power-up (see ordering options). Advanced Sector Protection/Unprotection S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 8.1 Lock Register As shipped from the factory, all devices default to the persistent mode when power is applied, and all sectors are unprotected, unless otherwise chosen through the DYB ordering option (see Ordering Information). The device programmer or host system must then choose which sector protection method to use. Programming (setting to “0”) any one of the following two one-time programmable, non-volatile bits locks the part permanently in that mode: Lock Register Persistent Protection Mode Lock Bit (DQ1) Lock Register Password Protection Mode Lock Bit (DQ2) Table 8.1. Lock Register Device DQ15-05 DQ4 DQ3 DQ2 DQ1 DQ0 S29WS256N 1 1 1 Password Protection Mode Lock Bit Persistent Protection Mode Lock Bit Customer SecSi Sector Protection Bit Password Protection Mode Lock Bit Persistent Protection Mode Lock Bit SecSi Sector Protection Bit DYB Lock Boot Bit S29WS128N/ S29WS064N Undefined 0 = sectors power up protected 1 = sectors power up unprotected PPB One-Time Programmable Bit 0 = All PPB erase command disabled 1 = All PPB Erase command enabled For programming lock register bits refer to Table 12.2. Notes 1. If the password mode is chosen, the password must be programmed before setting the corresponding lock register bit. 2. After the Lock Register Bits Command Set Entry command sequence is written, reads and writes for Bank 0 are disabled, while reads from other banks are allowed until exiting this mode. 3. If both lock bits are selected to be programmed (to zeros) at the same time, the operation will abort. 4. Once the Password Mode Lock Bit is programmed, the Persistent Mode Lock Bit is permanently disabled, and no changes to the protection scheme are allowed. Similarly, if the Persistent Mode Lock Bit is programmed, the Password Mode is permanently disabled. After selecting a sector protection method, each sector can operate in any of the following three states: 1. Constantly locked. The selected sectors are protected and can not be reprogrammed unless PPB lock bit is cleared via a password, hardware reset, or power cycle. 2. Dynamically locked. The selected sectors are protected and can be altered via software commands. 3. Unlocked. The sectors are unprotected and can be erased and/or programmed. These states are controlled by the bit types described in Sections 8.2–8.6. 8.2 Persistent Protection Bits The Persistent Protection Bits are unique and nonvolatile for each sector and have the same endurances as the Flash memory. Preprogramming and verification prior to erasure are handled by the device, and therefore do not require system monitoring. Notes 1. Each PPB is individually programmed and all are erased in parallel. 2. Entry command disables reads and writes for the bank selected. 3. Reads within that bank will return the PPB status for that sector. 4. Reads from other banks are allowed while writes are not allowed. October 29, 2004 S29WSxxxN_00_F0 51 P r e l i m i n a r y 5. All Reads must be performed using the Asynchronous mode. 6. The specific sector address (A23-A14 WS256N, A22-A14 WS128N, A21-A14 WS064N) are written at the same time as the program command. 7. If the PPB Lock Bit is set, the PPB Program or erase command will not execute and will time-out without programming or erasing the PPB. 8. There are no means for individually erasing a specific PPB and no specific sector address is required for this operation. 9. Exit command must be issued after the execution which resets the device to read mode and re-enables reads and writes for Bank 0 10. The programming state of the PPB for a given sector can be verified by writing a PPB Status Read Command to the device as described by the flow chart below. 8.3 Dynamic Protection Bits Dynamic Protection Bits are volatile and unique for each sector and can be individually modified. DYBs only control the protection scheme for unprotected sectors that have their PPBs cleared (erased to “1”). By issuing the DYB Set or Clear command sequences, the DYBs will be set (programmed to “0”) or cleared (erased to “1”), thus placing each sector in the protected or unprotected state respectively. This feature allows software to easily protect sectors against inadvertent changes yet does not prevent the easy removal of protection when changes are needed. Notes 1. The DYBs can be set (programmed to “0”) or cleared (erased to “1”) as often as needed. When the parts are first shipped, the PPBs are cleared (erased to “1”) and upon power up or reset, the DYBs can be set or cleared depending upon the ordering option chosen. 2. If the option to clear the DYBs after power up is chosen, (erased to “1”), then the sectors may be modified depending upon the PPB state of that sector (see Table 8.2). 3. The sectors would be in the protected state If the option to set the DYBs after power up is chosen (programmed to “0”). 4. It is possible to have sectors that are persistently locked with sectors that are left in the dynamic state. 5. The DYB Set or Clear commands for the dynamic sectors signify protected or unprotectedstate of the sectors respectively. However, if there is a need to change the status of the persistently locked sectors, a few more steps are required. First, the PPB Lock Bit must be cleared by either putting the device through a power-cycle, or hardware reset. The PPBs can then be changed to reflect the desired settings. Setting the PPB Lock Bit once again will lock the PPBs, and the device operates normally again. 6. To achieve the best protection, it is recommended to execute the PPB Lock Bit Set command early in the boot code and protect the boot code by holding WP# = VIL. Note that the PPB and DYB bits have the same function when ACC = VHH as they do when ACC =VIH. 8.4 Persistent Protection Bit Lock Bit The Persistent Protection Bit Lock Bit is a global volatile bit for all sectors. When set (programmed to “0”), this bit locks all PPB and when cleared (programmed to “1”), unlocks each sector. There is only one PPB Lock Bit per device. Notes 52 1. No software command sequence unlocks this bit unless the device is in the password protection mode; only a hardware reset or a power-up clears this bit. 2. The PPB Lock Bit must be set (programmed to “0”) only after all PPBs are configured to the desired settings. S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 8.5 Password Protection Method The Password Protection Method allows an even higher level of security than the Persistent Sector Protection Mode by requiring a 64 bit password for unlocking the device PPB Lock Bit. In addition to this password requirement, after power up and reset, the PPB Lock Bit is set “0” to maintain the password mode of operation. Successful execution of the Password Unlock command by entering the entire password clears the PPB Lock Bit, allowing for sector PPBs modifications. Notes 1. There is no special addressing order required for programming the password. Once the Password is written and verified, the Password Mode Locking Bit must be set in order to prevent access. 2. The Password Program Command is only capable of programming “0”s. Programming a “1” after a cell is programmed as a “0” results in a time-out with the cell as a “0”. 3. The password is all “1”s when shipped from the factory. 4. All 64-bit password combinations are valid as a password. 5. There is no means to verify what the password is after it is set. 6. The Password Mode Lock Bit, once set, prevents reading the 64-bit password on the data bus and further password programming. 7. The Password Mode Lock Bit is not erasable. 8. The lower two address bits (A1–A0) are valid during the Password Read, Password Program, and Password Unlock. 9. The exact password must be entered in order for the unlocking function to occur. 10. The Password Unlock command cannot be issued any faster than 1 µs at a time to prevent a hacker from running through all the 64-bit combinations in an attempt to correctly match a password. 11. Approximately 1 µs is required for unlocking the device after the valid 64-bit password is given to the device. 12. Password verification is only allowed during the password programming operation. 13. All further commands to the password region are disabled and all operations are ignored. 14. If the password is lost after setting the Password Mode Lock Bit, there is no way to clear the PPB Lock Bit. 15. Entry command sequence must be issued prior to any of any operation and it disables reads and writes for Bank 0. Reads and writes for other banks excluding Bank 0 are allowed. 16. If the user attempts to program or erase a protected sector, the device ignores the command and returns to read mode. 17. A program or erase command to a protected sector enables status polling and returns to read mode without having modified the contents of the protected sector. 18. The programming of the DYB, PPB, and PPB Lock for a given sector can be verified by writing individual status read commands DYB Status, PPB Status, and PPB Lock Status to the device. October 29, 2004 S29WSxxxN_00_F0 53 P r e l i m i n a r y Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Enter Lock Register Command: Address 555h, Data 40h XXXh = Address don’t care Program Lock Register Data Address XXXh, Data A0h Address 77h*, Data PD * Not on future devices Program Data (PD): See text for Lock Register definitions Caution: Lock data may only be progammed once. Wait 4 µs Perform Polling Algorithm (see Write Operation Status flowchart) Yes Done? No DQ5 = 1? No Error condition (Exceeded Timing Limits) Yes PASS. Write Lock Register Exit Command: Address XXXh, Data 90h Address XXXh, Data 00h Device returns to reading array. Figure 8.2. 54 FAIL. Write rest command to return to reading array. Lock Register Program Algorithm S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 8.6 Advanced Sector Protection Software Examples Table 8.2. Unique Device PPB Lock Bit 0 = locked 1 = unlocked Sector Protection Schemes Sector PPB 0 = protected 1 = unprotected Sector DYB 0 = protected 1 = unprotected Sector Protection Status Any Sector 0 0 x Protected through PPB Any Sector 0 0 x Protected through PPB Any Sector 0 1 1 Unprotected Any Sector 0 1 0 Protected through DYB Any Sector 1 0 x Protected through PPB Any Sector 1 0 x Protected through PPB Any Sector 1 1 0 Protected through DYB Any Sector 1 1 1 Unprotected Table 8.2 contains all possible combinations of the DYB, PPB, and PPB Lock Bit relating to the status of the sector. In summary, if the PPB Lock Bit is locked (set to “0”), no changes to the PPBs are allowed. The PPB Lock Bit can only be unlocked (reset to “1”) through a hardware reset or power cycle. See also Figure 8.1 for an overview of the Advanced Sector Protection feature. 8.7 Hardware Data Protection Methods The device offers two main types of data protection at the sector level via hardware control: When WP# is at VIL, the four outermost sectors are locked (device specific). When ACC is at VIL, all sectors are locked. There are additional methods by which intended or accidental erasure of any sectors can be prevented via hardware means. The following subsections describes these methods: 8.7.1. WP# Method The Write Protect feature provides a hardware method of protecting the four outermost sectors. This function is provided by the WP# pin and overrides the previously discussed Sector Protection/Unprotection method. If the system asserts VIL on the WP# pin, the device disables program and erase functions in the “outermost” boot sectors. The outermost boot sectors are the sectors containing both the lower and upper set of sectors in a dual-boot-configured device. If the system asserts VIH on the WP# pin, the device reverts to whether the boot sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these sectors depends on whether they were last protected or unprotected. Note that the WP# pin must not be left floating or unconnected as inconsistent behavior of the device may result. The WP# pin must be held stable during a command sequence execution 8.7.2 ACC Method This method is similar to above, except it protects all sectors. Once ACC input is set to VIL, all program and erase functions are disabled and hence all sectors are protected. October 29, 2004 S29WSxxxN_00_F0 55 P r e l i m i n a r y 8.7.3 Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to reading array data. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control inputs to prevent unintentional writes when VCC is greater than VLKO. 8.7.4 Write Pulse “Glitch Protection” Noise pulses of less than 3 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. 8.7.5 Power-Up Write Inhibit If WE# = CE# = RESET# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. 56 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y October 29, 2004 S29WSxxxN_00_F0 57 P r e l i m i n a r y 9 Power Conservation Modes 9.1 Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# inputs are both held at VCC ± 0.2 V. The device requires standard access time (tCE) for read access, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. I CC3 in “DC Characteristics” represents the standby current specification 9.2 Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption while in asynchronous mode. the device automatically enables this mode when addresses remain stable for tACC + 20 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. While in synchronous mode, the automatic sleep mode is disabled. Note that a new burst operation is required to provide new data. ICC6 in “DC Characteristics” represents the automatic sleep mode current specification. 9.3 Hardware RESET# Input Operation The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all outputs, resets the configuration register, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence to ensure data integrity. When RESET# is held at VSS ± 0.2 V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS ± 0.2 V, the standby current will be greater. RESET# may be tied to the system reset circuitry and thus, a system reset would also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. 9.4 Output Disable (OE#) When the OE# input is at VIH, output from the device is disabled. The outputs are placed in the high impedance state. 58 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 10 SecSiTM (Secured Silicon) Sector Flash Memory Region The SecSi (Secured Silicon) Sector provides an extra Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The SecSi Sector is 256 words in length that consists of 128 words for factory data and 128 words for customersecured areas. All SecSi reads outside of the 256-word address range will return invalid data. The Factory Indicator Bit, DQ7, (at Autoselect address 03h) is used to indicate whether or not the Factory SecSi Sector is locked when shipped from the factory. The Customer Indicator Bit (DQ6) is used to indicate whether or not the Customer SecSi Sector is locked when shipped from the factory. Please note the following general conditions: While SecSi Sector access is enabled, simultaneous operations are allowed except for Bank 0. On power-up, or following a hardware reset, the device reverts to sending commands to the normal address space. Reads can be performed in the Asynchronous or Synchronous mode. Burst mode reads within SecSi Sector will wrap from address FFh back to address 00h. Reads outside of sector 0 will return memory array data. Continuous burst read past the maximum address is undefined. Sector 0 is remapped from memory array to SecSi Sector array. Once the SecSi Sector Entry Command is issued, the SecSi Sector Exit command must be issued to exit SecSi Sector Mode. The SecSi Sector is not accessible when the device is executing an Embedded Program or Embedded Erase algorithm. Table 10.1. Sector Customer Factory SecSiTM Sector Addresses Sector Size 128 words 128 words Address Range 000080h-0000FFh 000000h-00007Fh 10.1 Factory SecSiTM Sector The Factory SecSi Sector is always protected when shipped from the factory and has the Factory Indicator Bit (DQ7) permanently set to a “1”. This prevents cloning of a factory locked part and ensures the security of the ESN and customer code once the product is shipped to the field. These devices are available pre programmed with one of the following: A random, 8 Word secure ESN only within the Factory SecSi Sector Customer code within the Customer SecSi Sector through the SpansionTM programming service. Both a random, secure ESN and customer code through the Spansion programming service. Customers may opt to have their code programmed through the Spansion programming services. Spansion programs the customer's code, with or without the random ESN. The devices are then shipped from the Spansion factory with the Factory SecSi Sector and Customer SecSi Sector permanently locked. Contact your local representative for details on using Spansion programming services. October 29, 2004 S29WSxxxN_00_F0 59 P r e l i m i n a r y 10.2 Customer SecSiTM Sector The Customer SecSi Sector is typically shipped unprotected (DQ6 set to “0”), allowing customers to utilize that sector in any manner they choose. If the security feature is not required, the Customer SecSi Sector can be treated as an additional Flash memory space. Please note the following: Once the Customer SecSi Sector area is protected, the Customer Indicator Bit will be permanently set to “1.” The Customer SecSi Sector can be read any number of times, but can be programmed and locked only once. The Customer SecSi Sector lock must be used with caution as once locked, there is no procedure available for unlocking the Customer SecSi Sector area and none of the bits in the Customer SecSi Sector memory space can be modified in any way. The accelerated programming (ACC) and unlock bypass functions are not available when programming the Customer SecSi Sector, but reading in Banks 1 through 15 is available. Once the Customer SecSi Sector is locked and verified, the system must write the Exit SecSi Sector Region command sequence which return the device to the memory array at sector 0. 10.3 SecSiTM Sector Entry and SecSi Sector Exit Command Sequences The system can access the SecSi Sector region by issuing the three-cycle Enter SecSi Sector command sequence. The device continues to access the SecSi Sector region until the system issues the four-cycle Exit SecSi Sector command sequence. See Command Definition Table [SecSiTM Sector Command Table, Appendix Table 12.1 for address and data requirements for both command sequences. The SecSi Sector Entry Command allows the following commands to be executed Read customer and factory SecSi areas Program the customer SecSi Sector After the system has written the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by sector SA0 within the memory array. This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or until power is removed from the device. Software Functions and Sample Code The following are C functions and source code examples of using the SecSi Sector Entry, Program, and exit commands. Refer to the Spansion Low Level Driver User’s Guide (available soon on www.amd.com and www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. Table 10.2. SecSi Sector Entry (LLD Function = lld_SecSiSectorEntryCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Base + AAAh Base + 555h 00AAh Unlock Cycle 2 Write Base + 554h Base + 2AAh 0055h Entry Cycle Write Base + AAAh Base + 555h 0088h Note: Base = Base Address. /* Example: SecSi Sector Entry Command */ 60 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; *( (UINT16 *)base_addr + 0x555 ) = 0x0088; Table 10.3. /* write unlock cycle 1 /* write unlock cycle 2 /* write Secsi Sector Entry Cmd */ */ */ SecSi Sector Program (LLD Function = lld_ProgramCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Base + AAAh Base + 555h 00AAh Unlock Cycle 2 Write Base + 554h Base + 2AAh 0055h Program Setup Write Base + AAAh Base + 555h 00A0h Program Write Word Address Word Address Data Word Note: Base = Base Address. /* Once in the SecSi Sector mode, you program */ /* words using the programming algorithm. */ Table 10.4. SecSi Sector Entry (LLD Function = lld_SecSiSectorExitCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Base + AAAh Base + 555h 00AAh Unlock Cycle 2 Write Base + 554h Base + 2AAh 0055h Exit Cycle Write Base + AAAh Base + 555h 0090h Note: Base = Base Address. /* Example: SecSi Sector *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr October 29, 2004 S29WSxxxN_00_F0 Exit Command */ + 0x555 ) = 0x00AA; + 0x2AA ) = 0x0055; + 0x555 ) = 0x0090; + 0x000 ) = 0x0000; /* /* /* /* write write write write unlock cycle unlock cycle SecSi Sector SecSi Sector 1 2 Exit cycle 3 Exit cycle 4 */ */ */ */ 61 P r e l i m i n a r y 11 Electrical Specifications 11.1 Absolute Maximum Ratings Storage Temperature Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +150°C Ambient Temperature with Power Applied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +125°C Voltage with Respect to Ground: All Inputs and I/Os except as noted below (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VIO + 0.5 V VCC (Note 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +2.5 V VIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +2.5 V ACC (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +9.5 V Output Short Circuit Current (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA Notes: 1. Minimum DC voltage on input or I/Os is –0.5 V. During voltage transitions, inputs or I/Os may undershoot VSS to –2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC voltage on input or I/Os is VCC + 0.5 V. During voltage transitions outputs may overshoot to VCC + 2.0 V for periods up to 20 ns. See Figure 11.2. 2. Minimum DC input voltage on pin ACC is -0.5V. During voltage transitions, ACC may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC voltage on pin ACC is +9.5 V, which may overshoot to 10.5 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. 4. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. 20 ns 20 ns 20 ns VCC +2.0 V VCC +0.5 V +0.8 V –0.5 V –2.0 V 1.0 V 20 ns Figure 11.1. 62 Maximum Negative Overshoot Waveform 20 ns Figure 11.2. 20 ns Maximum Positive Overshoot Waveform S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 11.2 Operating Ranges Wireless (W) Devices Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25°C to +85°C Industrial (I) Devices Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C Supply Voltages VCC Supply Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +1.70 V to +1.95 V VIO Supply Voltages: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Contact local sales office for VIO = 1.35 to +1.70 V.) +1.70 V to +1.95 V Notes: Operating ranges define those limits between which the functionality of the device is guaranteed. 11.3 Test Conditions Device Under Test CL Figure 11.3. Table 11.1. Test Specifications Test Condition All Speed Options Unit Output Load Capacitance, CL (including jig capacitance) 30 pF Input Rise and Fall Times Input Pulse Levels October 29, 2004 S29WSxxxN_00_F0 Test Setup 3.0 @ 54, 66 MHz 2.5 @ 80 MHz ns 0.0–VIO V Input timing measurement reference levels VIO/2 V Output timing measurement reference levels VIO/2 V 63 P r e l i m i n a r y 11.4 Key to Switching Waveforms WAVEFORM INPUTS OUTPUTS Steady Changing from H to L Changing from L to H Don’t Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is High Impedance State (High Z) 11.5 Switching Waveforms VIO All Inputs and Outputs Input VIO/2 Measurement Level VIO/2 Output 0.0 V Figure 11.4. Input Waveforms and Measurement Levels 11.6 VCC Power-up Parameter Description Test Setup Speed Unit tVCS VCC Setup Time Min 1 ms Notes: 1. VCC >= VIO - 100mV and VCC ramp rate is > 1V / 100µs 2. VCC ramp rate <1V / 100µs, a Hardware Reset will be required. tVCS VCC VIO RESET# Figure 11.5. 64 VCC Power-up Diagram S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 11.7 DC Characteristics (CMOS Compatible) Parameter Max Unit ILI Input Load Current Description (Notes) VIN = VSS to VCC, VCC = VCCmax Test Conditions (Notes 1, 2, 9) ±1 µA ILO Output Leakage Current (3) VOUT = VSS to VCC, VCC = VCCmax ±1 µA CE# = VIL, OE# = VIH, WE# = VIH, burst length = 8 CE# = VIL, OE# = VIH, WE# = VIH, burst length = 16 ICCB VCC Active burst Read Current CE# = VIL, OE# = VIH, WE# = VIH, burst length = 32 CE# = VIL, OE# = VIH, WE# = VIH, burst length = Continuous IIO1 VIO Non-active Output Min Typ 54 MHz 27 54 mA 66 MHz 28 60 mA 80 MHz 30 66 mA 54 MHz 28 48 mA 66 MHz 30 54 mA 80 MHz 32 60 mA 54 MHz 29 42 mA 66 MHz 32 48 mA 80 MHz 34 54 mA 54 MHz 32 36 mA 66 MHz 35 42 mA 80 MHz 38 48 mA 20 30 µA 10 MHz 27 36 mA 5 MHz 13 18 mA 1 MHz 3 4 mA OE# = VIH VCC Active Asynchronous Read Current (4) CE# = VIL, OE# = VIH, WE# = VIH ICC2 VCC Active Write Current (5) CE# = VIL, OE# = VIH, ACC = VIH VACC 1 5 µA VCC 19 52.5 mA ICC3 VCC Standby Current (6, 7) CE# = RESET# = VCC ± 0.2 V VACC 1 5 µA VCC 20 40 µA ICC4 VCC Reset Current (7) RESET# = VIL, CLK = VIL 70 150 µA ICC5 VCC Active Current (Read While Write) (7) CE# = VIL, OE# = VIH, ACC = VIH 50 60 mA ICC6 VCC Sleep Current (7) CE# = VIL, OE# = VIH 2 40 µA IACC CE# = VIL, OE# = VIH, Accelerated Program Current (8) V ACC = 9.5 V 6 20 mA 20 mA ICC1 VACC 14 VCC VIL Input Low Voltage VIO = 1.8 V –0.5 0.4 V VIH Input High Voltage VIO = 1.8 V VIO – 0.4 VIO + 0.4 V 0.1 V VOL Output Low Voltage IOL = 100 µA, VCC = VCC min = VIO VOH Output High Voltage IOH = –100 µA, VCC = VCC min = VIO VHH Voltage for Accelerated Program 8.5 9.5 V VLKO Low VCC Lock-out Voltage 1.0 1.4 V VIO – 0.1 V Notes: 1. Maximum ICC specifications are tested with VCC = VCCmax. 2. VCC= VIO. 3. CE# must be set high when measuring the RDY pin. 4. The ICC current listed is typically less than 3 mA/MHz, with OE# at VIH. 5. ICC active while Embedded Erase or Embedded Program is in progress. 6. Device enters automatic sleep mode when addresses are stable for tACC + 20 ns. Typical sleep mode current is equal to ICC3. 7. VIH = VCC ± 0.2 V and VIL > –0.1 V. 8. Total current during accelerated programming is the sum of VACC and VCC currents. 9. VACC = VHH on ACC input. October 29, 2004 S29WSxxxN_00_F0 65 P r e l i m i n a r y 11.8 AC Characteristics 11.8.1. CLK Characterization Parameter Description 54 MHz 66 MHz 80 MHz Unit fCLK CLK Frequency Max 54 66 80 MHz tCLK CLK Period Min 18.5 15.1 12.5 ns tCH CLK High Time tCL CLK Low Time Min 7.4 6.1 5.0 ns tCR CLK Rise Time tCF CLK Fall Time Max 3 3 2.5 ns tCLK tCH CLK tCF tCR Figure 11.6. 66 tCL CLK Characterization S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 11.8.2 Synchronous/Burst Read Parameter JEDEC Standard Description 54 MHz 66 MHz 80 MHz 69 Unit tIACC Latency Max ns tBACC Burst Access Time Valid Clock to Output Delay Max 13.5 tACS Address Setup Time to CLK (Note 1) Min 5 4 ns tACH Address Hold Time from CLK (Note 1) Min 7 6 ns tBDH Data Hold Time from Next Clock Cycle Min 4 3 ns tCR Chip Enable to RDY Valid Max 13.5 tOE Output Enable to Output Valid Max 13.5 tCEZ Chip Enable to High Z (Note 2) Max 10 ns tOEZ Output Enable to High Z (Note 2) Max 10 ns tCES CE# Setup Time to CLK Min 4 ns tRDYS RDY Setup Time to CLK Min 5 4 3.5 ns tRACC Ready Access Time from CLK Max 13.5 11.2 9 ns tCAS CE# Setup Time to AVD# Min 0 ns tAVC AVD# Low to CLK Min 4 ns tAVD AVD# Pulse Min 8 ns tAOE AVD Low to OE# Low Max 38.4 ns 11.2 9 11.2 9 11.2 ns ns ns Notes: 1. Addresses are latched on the first rising edge of CLK. 2. Not 100% tested. October 29, 2004 S29WSxxxN_00_F0 67 P r e l i m i n a r y 11.8.3 Timing Diagrams 5 cycles for initial access shown. tCES tCEZ 18.5 ns typ. (54 MHz) CE# 1 2 3 4 5 6 7 CLK tAVC AVD# tAVD tACS Addresses Aa tBACC tACH Hi-Z Data (n) tIACC Da tAOE Da + 1 Da + 2 Da + 3 Da + n tOEZ tBDH OE# tOE RDY (n) tRACC Hi-Z Hi-Z tCR tRDYS Hi-Z Data (n + 1) Da RDY (n + 1) Da + 1 Da + 2 Da + 2 Da + n Hi-Z Hi-Z Hi-Z Data (n + 2) Da RDY (n + 2) Da + 1 Da + 1 Da + 1 Da + n Hi-Z Hi-Z Hi-Z Data (n + 3) Da RDY (n + 3) Da Da Da Hi-Z Da + n Hi-Z Notes: 1. Figure shows total number of wait states set to five cycles. The total number of wait states can be programmed from two cycles to seven cycles. 2. If any burst address occurs at “address + 1”, “address + 2”, or “address + 3”, additional clock delay cycles are inserted, and are indicated by RDY. 3. The device is in synchronous mode. Figure 11.7. 68 CLK Synchronous Burst Mode Read S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 7 cycles for initial access shown. tCES CE# 1 2 3 4 5 6 7 CLK tAVC AVD# tAVD tACS Addresses Ac tBACC tACH Data tIACC DC DE DD DF DB D8 tBDH tAOE OE# tCR RDY tRACC tRACC tOE Hi-Z tRDYS Notes: 1. 2. 3. 4. Figure shows total number of wait states set to seven cycles. The total number of wait states can be programmed from two cycles to seven cycles. If any burst address occurs at “address + 1”, “address + 2”, or “address + 3”, additional clock delay cycles are inserted, and are indicated by RDY. The device is in synchronous mode with wrap around. D8–DF in data waveform indicate the order of data within a given 8-word address range, from lowest to highest. Starting address in figure is the 4th address in range (0-F). Figure 11.8. tCES 8-word Linear Burst with Wrap Around 7 cycles for initial access shown. CE# 1 2 3 4 5 6 7 CLK tAVC AVD# tAVD tACS Addresses Ac tBACC tACH Data tIACC tAOE DC DD DE DF D10 D13 tBDH OE# tCR RDY tOE tRACC tRACC Hi-Z tRDYS Notes: 1. 2. 3. 4. Figure shows total number of wait states set to seven cycles. The total number of wait states can be programmed from two cycles to seven cycles. Clock is set for active rising edge. If any burst address occurs at “address + 1”, “address + 2”, or “address + 3”, additional clock delay cycles are inserted, and are indicated by RDY. The device is in asynchronous mode with out wrap around. DC–D13 in data waveform indicate the order of data within a given 8-word address range, from lowest to highest. Starting address in figure is the 1st address in range (c-13). Figure 11.9. October 29, 2004 S29WSxxxN_00_F0 8-word Linear Burst without Wrap Around 69 P r e l i m i n a r y tCES tCEZ 6 wait cycles for initial access shown. CE# 1 2 3 4 5 6 CLK tAVC AVD# tAVD tACS Addresses Aa tBACC tACH Hi-Z Data tIACC Da Da+2 Da+3 Da + n tOEZ tRACC OE# tCR RDY Da+1 tBDH tAOE tOE Hi-Z Hi-Z tRDYS Notes: 1. Figure assumes 6 wait states for initial access and synchronous read. 2. The Set Configuration Register command sequence has been written with CR8=0; device will output RDY one cycle before valid data. Figure 11.10. Linear Burst with RDY Set One Cycle Before Data 11.8.4 AC Characteristics—Asynchronous Read Parameter JEDEC Standard Description 54 MHz 80 MHz 66 MHz Unit tCE Access Time from CE# Low Max 70 ns tACC Asynchronous Access Time Max 70 ns tAVDP AVD# Low Time Min 8 ns tAAVDS Address Setup Time to Rising Edge of AVD# Min 4 ns tAAVDH Address Hold Time from Rising Edge of AVD# Min 7 6 ns tOE Output Enable to Output Valid Max 13.5 11.2 ns tOEH Output Enable Hold Time tOEZ tCAS Read Min 0 ns Toggle and Data# Polling Min 10 ns Output Enable to High Z (see Note) Max 10 ns CE# Setup Time to AVD# Min 0 ns Note: Not 100% tested. 70 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y CE# tOE OE# tOEH WE# tCE tOEZ Data Valid RD tACC RA Addresses tAAVDH tCAS AVD# tAVDP tAAVDS Note: RA = Read Address, RD = Read Data. Figure 11.11. October 29, 2004 S29WSxxxN_00_F0 Asynchronous Mode Read 71 P r e l i m i n a r y 11.8.5 Hardware Reset (RESET#) Parameter JEDEC Std. Description All Speed Options Unit tRP RESET# Pulse Width Min 30 µs tRH Reset High Time Before Read (See Note) Min 200 ns Note: Not 100% tested. CE#, OE# tRH RESET# tRP Figure 11.12. 72 Reset Timings S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 11.8.6 Erase/Program Timing Parameter JEDEC Standard tAVAV tWC tAVWL tWLAX tAS tAH Description 54 MHz Write Cycle Time (Note 1) Address Setup Time (Notes 2, 3) Address Hold Time (Notes 2, 3) Min Synchronous Asynchronous Synchronous Asynchronous Min tAVDP AVD# Low Time Min tDS Data Setup Time Min tWHDX tDH Data Hold Time Min tGHWL tGHWL 80 MHz Unit 70 ns 5 ns 0 ns 9 Min tDVWH 66 MHz ns 20 8 45 ns 20 0 ns ns Read Recovery Time Before Write Min 0 ns tCAS CE# Setup Time to AVD# Min 0 ns tWHEH tCH CE# Hold Time Min 0 ns tWLWH tWP Write Pulse Width Min 30 ns tWHWL tWPH Write Pulse Width High Min 20 ns tSR/W Latency Between Read and Write Operations Min 0 ns tVID VACC Rise and Fall Time Min 500 ns tVIDS VACC Setup Time (During Accelerated Programming) Min 1 µs tVCS VCC Setup Time Min 50 µs tCS CE# Setup Time to WE# Min 5 ns tAVSW AVD# Setup Time to WE# Min 5 ns tAVHW AVD# Hold Time to WE# Min 5 ns tAVSC AVD# Setup Time to CLK Min 5 ns tAVHC AVD# Hold Time to CLK Min 5 ns tCSW Clock Setup Time to WE# Min 5 ns tWEP Noise Pulse Margin on WE# Max 3 ns tSEA Sector Erase Accept Time-out Max 50 µs tESL Erase Suspend Latency Max 20 µs tPSL Program Suspend Latency Max 20 µs tASP Toggle Time During Sector Protection Typ 100 µs tPSP Toggle Time During Programming Within a Protected Sector Typ 1 µs tELWL Notes: 1. 2. 3. 4. 5. Not 100% tested. Asynchronous read mode allows Asynchronous program operation only. Synchronous read mode allows both Asynchronous and Synchronous program operation. In asynchronous program operation timing, addresses are latched on the falling edge of WE#. In synchronous program operation timing, addresses are latched on the rising edge of CLK. See the “Erase and Programming Performance” section for more information. Does not include the preprogramming time. October 29, 2004 S29WSxxxN_00_F0 73 P r e l i m i n a r y Erase Command Sequence (last two cycles) VIH Read Status Data CLK VIL tAVDP AVD# tAH tAS Addresses 555h for chip erase Data VA SA 2AAh 55h VA 10h for chip erase In Progress 30h Complete tDS tDH CE# tCH OE# tWP WE# tCS tVCS tWHWH2 tWPH tWC VCC Figure 11.2. 74 Chip/Sector Erase Operation Timings: WE# Latched Addresses S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Program Command Sequence (last two cycles) Read Status Data VIH CLK VIL tAVSW tAVHW tAVDP AVD tAS tAH Addresses 555h VA PA Data A0h VA In Progress PD Complete tDS tCAS tDH CE# tCH OE# tWP WE# tWHWH1 tCS tWPH tWC tVCS VCC Notes: 1. PA = Program Address, PD = Program Data, VA = Valid Address for reading status bits. 2. “In progress” and “complete” refer to status of program operation. 3. A23–A14 for the WS256N (A22–A14 for the WS128N, A21–A14 for the WS064N) are don’t care during command sequence unlock cycles. 4. CLK can be either VIL or VIH. 5. The Asynchronous programming operation is independent of the Set Device Read Mode bit in the Configuration Register. Figure 11.13. October 29, 2004 S29WSxxxN_00_F0 Asynchronous Program Operation Timings: WE# Latched Addresses 75 P r e l i m i n a r y Program Command Sequence (last two cycles) Read Status Data tAVCH CLK tAS tAH tAVSC AVD tAVDP Addresses VA PA 555h Data In Progress PD A0h VA Complete tDS tDH tCAS CE# OE# tCH tCSW tWP WE# tWHWH1 tWPH tWC tVCS VCC Notes: 1. PA = Program Address, PD = Program Data, VA = Valid Address for reading status bits. 2. “In progress” and “complete” refer to status of program operation. 3. A23–A14 for the WS256N (A22–A14 for the WS128N, A21–A14 for the WS064N) are don’t care during command sequence unlock cycles. 4. Addresses are latched on the first rising edge of CLK. 5. Either CE# or AVD# is required to go from low to high in between programming command sequences. 6. The Synchronous programming operation is dependent of the Set Device Read Mode bit in the Configuration Register. The Configuration Register must be set to the Synchronous Read Mode. Figure 11.14. 76 Synchronous Program Operation Timings: CLK Latched Addresses S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y CE# AVD# WE# Addresses PA Data Don't Care OE# tVIDS ACC A0h Don't Care PD Don't Care VID tVID VIL or VIH Note: Use setup and hold times from conventional program operation. Figure 11.15. Accelerated Unlock Bypass Programming Timing AVD# tCEZ tCE CE# tCH tOEZ tOE OE# tOEH WE# tACC Addresses VA High Z VA High Z Status Data Data Status Data Notes: 1. 2. Status reads in figure are shown as asynchronous. VA = Valid Address. Two read cycles are required to determine status. When the Embedded Algorithm operation is complete, and Data# Polling will output true data. Figure 11.16. October 29, 2004 S29WSxxxN_00_F0 Data# Polling Timings (During Embedded Algorithm) 77 P r e l i m i n a r y AVD# tCEZ tCE CE# tCH tOEZ tOE OE# tOEH WE# tACC Addresses VA High Z VA High Z Data Status Data Status Data Notes: 1. 2. Status reads in figure are shown as asynchronous. VA = Valid Address. Two read cycles are required to determine status. When the Embedded Algorithm operation is complete, the toggle bits will stop toggling. Figure 11.17. Toggle Bit Timings (During Embedded Algorithm) CE# CLK AVD# Addresses VA VA OE# tIACC tIACC Data Status Data Status Data RDY Notes: 1. 2. 3. The timings are similar to synchronous read timings. VA = Valid Address. Two read cycles are required to determine status. When the Embedded Algorithm operation is complete, the toggle bits will stop toggling. RDY is active with data (D8 = 1 in the Configuration Register). When D8 = 0 in the Configuration Register, RDY is active one clock cycle before data. Figure 11.18. 78 Synchronous Data Polling Timings/Toggle Bit Timings S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Enter Embedded Erasing Erase Suspend Erase WE# Enter Erase Suspend Program Erase Suspend Read Erase Resume Erase Suspend Program Erase Complete Erase Erase Suspend Read DQ6 DQ2 Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6. Figure 11.19. DQ2 vs. DQ6 Address boundary occurs every 128 words, beginning at address 00007Fh: (0000FFh, 00017Fh, etc.) Address 000000h is also a boundary crossing. C124 C125 C126 7C 7D 7E C127 C127 C128 C129 7F 7F 80 81 C130 C131 CLK Address (hex) AVD# 83 (stays high) tRACC tRACC RDY(1) latency tRACC RDY(2) tRACC latency Data OE#, CE# 82 D124 D125 D126 D127 D128 D129 D130 (stays low) Notes: 1. 2. 3. 4. 5. RDY(1) active with data (D8 = 1 in the Configuration Register). RDY(2) active one clock cycle before data (D8 = 0 in the Configuration Register). Cxx indicates the clock that triggers Dxx on the outputs; for example, C60 triggers D60. Figure shows the device not crossing a bank in the process of performing an erase or program. RDY will not go low and no additional wait states will be required if the Burst frequency is <=66 MHz and the Boundary Crossing bit (D14) in the Configuration Register is set to 0 Figure 11.20. October 29, 2004 S29WSxxxN_00_F0 Latency with Boundary Crossing when Frequency > 66 MHz 79 P r e l i m i n a r y Address boundary occurs every 128 words, beginning at address 00007Fh: (0000FFh, 00017Fh, etc.) Address 000000h is also a boundary crossing. C124 C125 C126 7C 7D 7E C127 C127 CLK Address (hex) AVD# 7F 7F (stays high) tRACC tRACC RDY(1) latency tRACC RDY(2) latency Data OE#, CE# tRACC D124 D125 D126 D127 Read Status (stays low) Notes: 1. 2. 3. 4. 5. RDY(1) active with data (D8 = 1 in the Configuration Register). RDY(2) active one clock cycle before data (D8 = 0 in the Configuration Register). Cxx indicates the clock that triggers Dxx on the outputs; for example, C60 triggers D60. Figure shows the device crossing a bank in the process of performing an erase or program. RDY will not go low and no additional wait states will be required if the Burst frequency is < 66 MHz and the Boundary Crossing bit (D14) in the Configuration Register is set to 0. Figure 11.21. 80 Latency with Boundary Crossing into Program/Erase Bank S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Data D0 D1 Rising edge of next clock cycle following last wait state triggers next burst data AVD# total number of clock cycles following addresses being latched OE# 1 2 3 0 1 4 5 6 7 3 4 5 CLK 2 number of clock cycles programmed Wait State Configuration Register Setup: D13, D13, D13, D13, D13, D13, D13, D13, D12, D12, D12, D12, D12, D12, D12, D12, D11 D11 D11 D11 D11 D11 D11 D11 = = = = = = = = “111” “110” “101” “100” “011” “010” “001” “000” ⇒ Reserved ⇒ Reserved ⇒ 5 programmed, 7 total ⇒ 4 programmed, 6 total ⇒ 3 programmed, 5 total ⇒ 2 programmed, 4 total ⇒ 1 programmed, 3 total ⇒ 0 programmed, 2 total Note: Figure assumes address D0 is not at an address boundary, and wait state is set to “101”. Figure 11.22. October 29, 2004 S29WSxxxN_00_F0 Example of Wait States Insertion 81 P r e l i m i n a r y Last Cycle in Program or Sector Erase Command Sequence Read status (at least two cycles) in same bank and/or array data from other bank tWC tRC Begin another write or program command sequence tRC tWC CE# OE# tOE tOEH tGHWL WE# tWPH Data tWP tDS tOEZ tACC tOEH tDH RD RD PD/30h AAh tSR/W Addresses PA/SA RA RA 555h tAS AVD# tAH Note: Breakpoints in waveforms indicate that system may alternately read array data from the “non-busy bank” while checking the status of the program or erase operation in the “busy” bank. The system should read status twice to ensure valid information. Figure 11.23. 82 Back-to-Back Read/Write Cycle Timings S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 11.8.7 Erase and Programming Performance Parameter Sector Erase Time Typ (Note 1) Max (Note 2) 64 Kword VCC 0.6 3.5 16 Kword VCC <0.15 2 153.6 (WS256N) 308 (WS256N) 154 (WS128N) 78 (WS064N) VCC 39.3 (WS064N) Chip Erase Time 130.6 (WS256N) 33.4 (WS064N) VCC 40 400 ACC 24 240 Effective Word Programming Time utilizing Program Write Buffer VCC 9.4 94 ACC 6 60 Total 32-Word Buffer Programming Time VCC 300 3000 ACC 192 1920 157.3 (WS256N) 39.3 (WS064N) 314.6 (WS256N) 157.3 (WS128N) 78.6 (WS064N) 100.7 (WS256N) 50.3 (WS128N) 25.2 (WS064N) 201.3 (WS256N) 100.7 (WS128N) 50.3 (WS064N) VCC Chip Programming Time (Note 3) ACC 65.8 (WS128N) 78.6 (WS128N) Comments s s 262 (WS256N) 132 (WS128N) 66 (WS064N) ACC Single Word Programming Time (Note 8) 77.4 (WS128N) Unit Excludes 00h programming prior to erasure (Note 4) µs µs µs s Excludes system level overhead (Note 5) Notes: 1. Typical program and erase times assume the following conditions: 25°C, 1.8 V VCC, 10,000 cycles; checkerboard data pattern. 2. Under worst case conditions of 90°C, VCC = 1.70 V, 100,000 cycles. 3. Typical chip programming time is considerably less than the maximum chip programming time listed, and is based on single word programming. 4. In the pre-programming step of the Embedded Erase algorithm, all words are programmed to 00h before erasure. 5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See the Appendix for further information on command definitions. 6. Contact the local sales office for minimum cycling endurance values in specific applications and operating conditions. 7. Refer to Application Note “Erase Suspend/Resume Timing” for more details. 8. Word programming specification is based upon a single word programming operation not utilizing the write buffer. October 29, 2004 S29WSxxxN_00_F0 83 P r e l i m i n a r y 11.8.8 BGA Ball Capacitance Parameter Symbol Parameter Description Test Setup Typ. Max Unit CIN Input Capacitance VIN = 0 5.3 6.3 pF COUT Output Capacitance VOUT = 0 5.8 6.8 pF CIN2 Control Pin Capacitance VIN = 0 6.3 7.3 pF Notes: 1. Sampled, not 100% tested. 2. Test conditions TA = 25°C; f = 1.0 MHz. 84 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 12 Appendix This section contains information relating to software control or interfacing with the Flash device. For additional information and assistance regarding software, see the Additional Resources section on page 15, or explore the Web at www.amd.com and www.fujitsu.com. October 29, 2004 S29WSxxxN_00_F0 85 Autoselect (8) Command Sequence (Notes) Asynchronous Read (6) Reset (7) Manufacturer ID Device ID (9) Cycles P r e l i m i n a r y 1 1 4 6 Table 12.1. Memory Array Commands First Addr Data RA RD XXX F0 555 AA 555 AA Second Addr Data Bus Cycles (Notes 1–5) Third Fourth Addr Data Addr Data 2AA 2AA 55 55 [BA]555 [BA]555 90 90 [BA]X00 [BA]X01 0001 227E Data BA+X0F 2200 PD WC PA PD WBL PD 555 555 AA AA 2AA 2AA 55 55 555 SA 10 30 X00 X00 CR CR 88 A0 PA PD 90 XXX 00 555 AA 2AA 55 [BA]555 90 [BA]X03 Data Program Write to Buffer (11) Program Buffer to Flash Write to Buffer Abort Reset (12) Chip Erase Sector Erase Erase/Program Suspend (13) Erase/Program Resume (14) Set Configuration Register (18) Read Configuration Register CFI Query (15) Entry Program (16) CFI (16) 4 6 1 3 6 6 1 1 4 4 1 3 2 1 555 555 SA 555 555 555 BA BA 555 555 [BA]555 555 XXX XXX AA AA 29 AA AA AA B0 30 AA AA 98 AA A0 98 2AA 2AA 55 55 555 PA A0 25 PA PA 2AA 2AA 2AA 55 55 55 555 555 555 F0 80 80 2AA 2AA 55 55 555 555 D0 C6 2AA PA 55 PD 555 20 Reset 2 XXX 90 XXX 00 Entry Program (17) Read (17) 3 4 1 555 555 00 AA AA Data 2AA 2AA 55 55 555 555 Exit (17) 4 555 AA 2AA 55 555 SecSi Sector Unlock Bypass Mode 4 Notes: 1. See Table 6.4 for description of bus operations. 2. All values are in hexadecimal. 3. Shaded cells indicate read cycles. 4. Address and data bits not specified in table, legend, or notes are don’t cares (each hex digit implies 4 bits of data). 5. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. The system must write the reset command to return the device to reading array data. 6. No unlock or command cycles required when bank is reading array data. 7. Reset command is required to return to reading array data (or to the erase-suspend-read mode if previously in Erase Suspend) when a bank is in the autoselect mode, or if DQ5 goes high (while the bank is providing status information) or performing sector lock/unlock. 8. The system must provide the bank address. See Autoselect section for more information. 9. Data in cycle 5 is 2230 (WS256N), 2232 (WS064N), or 2231 (WS128N). 10. See Table 7.16 for indicator bit values. 86 Sixth Addr Data BA+X0E Indicator Bits (10) Legend: X = Don’t care. RA = Read Address. RD = Read Data. PA = Program Address. Addresses latch on the rising edge of the AVD# pulse or active edge of CLK, whichever occurs first. PD = Program Data. Data latches on the rising edge of WE# or CE# pulse, whichever occurs first. Fifth Addr Data SA = Sector Address. WS256N = A23–A14; WS128N = A22–A14; WS064N = A21–A14. BA = Bank Address. WS256N = A23–A20; WS128N = A22–A20; WS064N = A21–A18. CR = Configuration Register data bits D15–D0. WBL = Write Buffer Location. Address must be within the same write buffer page as PA. WC = Word Count. Number of write buffer locations to load minus 1. 11. Total number of cycles in the command sequence is determined by the number of words written to the write buffer. The number of cycles in the command sequence is 37 for full page programming (32 words). Less than 32 word programming is not recommended. 12. Command sequence resets device for next command after writeto-buffer operation. 13. System may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation, and requires the bank address. 14. Erase Resume command is valid only during the Erase Suspend mode, and requires the bank address. 15. Command is valid when device is ready to read array data or when device is in autoselect mode. Address will equal 55h on all future devices, but 555h for WS256N/128N/064N. 16. Requires Entry command sequence prior to execution. Unlock Bypass Reset command is required to return to reading array data. 17. Requires Entry command sequence prior to execution. SecSi Sector Exit Reset command is required to exit this mode; device may otherwise be placed in an unknown state. 18. Requires reset command to configure the Configuration Register. S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Command Sequence (Notes) Command Set Entry (5) Lock Program (6) Register Read (6) Bits Command Set Exit (7) Command Set Entry (5) Program [0-3] (8) Password Read (9) Protection Unlock Command Set Exit (7) Command Set Entry (5) PPB Program (10) Non-Volatile Sector All PPB Erase (10, 11) Protection (PPB) PPB Status Read Command Set Exit (7) Global Command Set Entry (5) Volatile Sector PPB Lock Bit Set Protection PPB Lock Bit Status Read Freeze Command Set Exit (7) (PPB Lock) Volatile Sector Protection (DYB) Command Set Entry (5) DYB Set DYB Clear DYB Status Read Command Set Exit (7) Cycles Table 12.2. 3 2 1 2 3 2 4 7 2 3 2 2 1 2 3 2 1 First Addr Data 555 AA XX A0 77 data XX 90 555 AA XX A0 0...00 PWD0 00 25 XX 90 555 AA XX A0 XX 80 SA RD(0) XX 90 555 AA XX A0 BA RD(0) Sector Protection Commands XX 00 2AA 55 555 60 00 PWD[0-3] 0...01 PWD1 0...02 PWD2 00 03 00 PWD0 XX 00 2AA 55 [BA]555 C0 SA 00 00 30 XX 2AA XX 00 55 00 2 XX 90 XX 00 3 2 2 1 2 555 XX XX SA XX AA A0 A0 RD(0) 90 2AA SA SA 55 00 01 XX 00 Legend: X = Don’t care. RA = Address of the memory location to be read. PD(0) = SecSi Sector Lock Bit. PD(0), or bit[0]. PD(1) = Persistent Protection Mode Lock Bit. PD(1), or bit[1], must be set to ‘0’ for protection while PD(2), bit[2] must be left as ‘1’. PD(2) = Password Protection Mode Lock Bit. PD(2), or bit[2], must be set to ‘0’ for protection while PD(1), bit[1] must be left as ‘1’. PD(3) = Protection Mode OTP Bit. PD(3) or bit[3]. SA = Sector Address. WS256N = A23–A14; WS128N = A22–A14; WS064N = A21–A14. Notes: 1. All values are in hexadecimal. 2. Shaded cells indicate read cycles. 3. Address and data bits not specified in table, legend, or notes are don’t cares (each hex digit implies 4 bits of data). 4. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. The system must write the reset command to return the device to reading array data. 5. Entry commands are required to enter a specific mode to enable instructions only available within that mode. October 29, 2004 S29WSxxxN_00_F0 Bus Cycles (Notes 1–4) Third Fourth Fifth Addr Data Addr Data Addr Data 555 40 Second Addr Data 2AA 55 77 data [BA]555 50 [BA]555 E0 0...03 PWD3 01 PWD1 02 PWD2 Sixth Addr Data 03 PWD3 Seventh Addr Data 00 29 BA = Bank Address. WS256N = A23–A20; WS128N = A22–A20; WS064N = A21–A18. PWD3–PWD0 = Password Data. PD3–PD0 present four 16 bit combinations that represent the 64-bit Password PWA = Password Address. Address bits A1 and A0 are used to select each 16-bit portion of the 64-bit entity. PWD = Password Data. RD(0), RD(1), RD(2) = DQ0, DQ1, or DQ2 protection indicator bit. If protected, DQ0, DQ1, or DQ2 = 0. If unprotected, DQ0, DQ1, DQ2 = 1. 6. 7. If both the Persistent Protection Mode Locking Bit and the Password Protection Mode Locking Bit are set at the same time, the command operation will abort and return the device to the default Persistent Sector Protection Mode during 2nd bus cycle. Note that on all future devices, addresses will equal 00h, but are currently 77h for WS256N, WS128N, and WS064N. See Tables 8.1 and 8.2 for explanation of lock bits. Exit command must be issued to reset the device into read mode; device may otherwise be placed in an unknown state. 8. Entire two bus-cycle sequence must be entered for each portion of the password. 9. Full address range is required for reading password. 10. See Figure 8.2 for details. 11. “All PPB Erase” command will pre-program all PPBs before erasure to prevent over-erasure. 87 P r e l i m i n a r y 12.1 Common Flash Memory Interface The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified soft-ware algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and back-ward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address (BA)555h any time the device is ready to read array data. The system can read CFI information at the addresses given in Tables 12.3–12.6) within that bank. All reads outside of the CFI address range, within the bank, will return non-valid data. Reads from other banks are allowed, writes are not. To terminate reading CFI data, the system must write the reset command. The following is a C source code example of using the CFI Entry and Exit functions. Refer to t he S pans io n Lo w Lev el Driver U s er ’s Gu ide ( avail able on www.am d.c o m a nd www.fujitsu.com) for general information on Spansion Flash memory software development guidelines. /* Example: CFI Entry command */ *( (UINT16 *)bank_addr + 0x555 ) = 0x0098; /* write CFI entry command */ /* Example: CFI Exit command */ *( (UINT16 *)bank_addr + 0x000 ) = 0x00F0; /* write cfi exit command */ For further information, please refer to the CFI Specification (see JEDEC publications JEP137A and JESD68.01and CFI Publication 100). Please contact your sales office for copies of these documents. Table 12.3. 88 CFI Query Identification String Addresses Data 10h 11h 12h 0051h 0052h 0059h Description Query Unique ASCII string “QRY” 13h 14h 0002h 0000h Primary OEM Command Set 15h 16h 0040h 0000h Address for Primary Extended Table 17h 18h 0000h 0000h Alternate OEM Command Set (00h = none exists) 19h 1Ah 0000h 0000h Address for Alternate OEM Extended Table (00h = none exists) S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Table 12.4. Addresses System Interface String Data Description 1Bh 0017h VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Ch 0019h VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Dh 0000h VPP Min. voltage (00h = no VPP pin present) 1Eh 0000h VPP Max. voltage (00h = no VPP pin present) 1Fh 0006h Typical timeout per single byte/word write 2N µs 20h 0009h Typical timeout for Min. size buffer write 2N µs (00h = not supported) 21h 000Ah Typical timeout per individual block erase 2N ms 22h 0000h Typical timeout for full chip erase 2N ms (00h = not supported) 23h 0004h Max. timeout for byte/word write 2N times typical 24h 0004h Max. timeout for buffer write 2N times typical 25h 0003h Max. timeout per individual block erase 2N times typical 26h 0000h Max. timeout for full chip erase 2N times typical (00h = not supported) Table 12.5. Device Geometry Definition Addresses Data 27h 0019h (WS256N) 0018h (WS128N) 0017h (WS064N) 28h 29h 0001h 0000h Flash Device Interface description (refer to CFI publication 100) 2Ah 2Bh 0006h 0000h Max. number of bytes in multi-byte write = 2N (00h = not supported) 2Ch 0003h Number of Erase Block Regions within device 2Dh 2Eh 2Fh 30h 0003h 0000h 0080h 0000h Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) 31h 00FDh (WS256N) 007Dh (WS128N) 003Dh (WS064N) 32h 33h 34h 0000h 0000h 0002h 35h 36h 37h 38h 0003h 0000h 0080h 0000h Erase Block Region 3 Information 39h 3Ah 3Bh 3Ch 0000h 0000h 0000h 0000h Erase Block Region 4 Information October 29, 2004 S29WSxxxN_00_F0 Description Device Size = 2N byte Erase Block Region 2 Information 89 P r e l i m i n a r y Table 12.6. Primary Vendor-Specific Extended Query Addresses Data Description 40h 41h 42h 0050h 0052h 0049h Query-unique ASCII string “PRI” 43h 0031h Major version number, ASCII 44h 0034h Minor version number, ASCII 45h 0100h Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Silicon Technology (Bits 5-2) 0100 = 0.11 µm 90 46h 0002h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write 47h 0001h Sector Protect 0 = Not Supported, X = Number of sectors in per group 48h 0000h Sector Temporary Unprotect 00 = Not Supported, 01 = Supported 49h 0008h Sector Protect/Unprotect scheme 08 = Advanced Sector Protection 4Ah 00F3h (WS256N) 006Fh (WS128N) 0037h (WS064N) 4Bh 0001h Burst Mode Type 00 = Not Supported, 01 = Supported 4Ch 0000h Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page, 04 = 16 Word Page 4Dh 0085h 4Eh 0095h 4Fh 0001h 50h 0001h 51h 0001h 52h 0007h SecSi Sector (Customer OTP Area) Size 2N bytes 53h 0014h Hardware Reset Low Time-out during an embedded algorithm to read mode Maximum 2N ns 54h 0014h Hardware Reset Low Time-out not during an embedded algorithm to read mode Maximum 2N ns 55h 0005h Erase Suspend Time-out Maximum 2N ns 56h 0005h Program Suspend Time-out Maximum 2N ns 57h 0010h Bank Organization: X = Number of banks 58h 0013h (WS256N) 000Bh (WS128N) 0007h (WS064N) Simultaneous Operation Number of Sectors in all banks except boot bank ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Top/Bottom Boot Sector Flag 0001h = Dual Boot Device Program Suspend. 00h = not supported Unlock Bypass 00 = Not Supported, 01=Supported Bank 0 Region Information. X = Number of sectors in bank S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Table 12.6. Primary Vendor-Specific Extended Query (Continued) Addresses Data 59h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 1 Region Information. X = Number of sectors in bank 5Ah 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 2 Region Information. X = Number of sectors in bank 5Bh 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 3 Region Information. X = Number of sectors in bank 5Ch 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 4 Region Information. X = Number of sectors in bank 5Dh 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 5 Region Information. X = Number of sectors in bank 5Eh 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 6 Region Information. X = Number of sectors in bank 5Fh 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 7 Region Information. X = Number of sectors in bank 60h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 8 Region Information. X = Number of sectors in bank 61h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 9 Region Information. X = Number of sectors in bank 62h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 10 Region Information. X = Number of sectors in bank 63h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 11 Region Information. X = Number of sectors in bank 64h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 12 Region Information. X = Number of sectors in bank 65h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 13 Region Information. X = Number of sectors in bank 66h 0010h (WS256N) 0008h (WS128N) 0004h (WS064N) Bank 14 Region Information. X = Number of sectors in bank 67h 0013h (WS256N) 000Bh (WS128N) 0007h (WS064N) Bank 15 Region Information. X = Number of sectors in bank October 29, 2004 S29WSxxxN_00_F0 Description 91 P r e l i m i n a r y 13 Commonly Used Terms Term Definition ACC ACCelerate. A special purpose input signal which allows for faster programming or erase operation when raised to a specified voltage above VCC. In some devices ACC may protect all sectors when at a low voltage. Amax Most significant bit of the address input [A23 for 256Mbit, A22 for128Mbit, A21 for 64Mbit] Amin Least significant bit of the address input signals (A0 for all devices in this document). Asynchronous Operation where signal relationships are based only on propagation delays and are unrelated to synchronous control (clock) signal. Autoselect Read mode for obtaining manufacturer and device information as well as sector protection status. Bank Section of the memory array consisting of multiple consecutive sectors. A read operation in one bank, can be independent of a program or erase operation in a different bank for devices that offer simultaneous read and write feature. Boot sector Smaller size sectors located at the top and or bottom of Flash device address space. The smaller sector size allows for finer granularity control of erase and protection for code or parameters used to initiate system operation after power-on or reset. Boundary Location at the beginning or end of series of memory locations. Burst Read See synchronous read. Byte 8 bits CFI Common Flash Interface. A Flash memory industry standard specification [JEDEC 137A and JESD68.01] designed to allow a system to interrogate the Flash to determine its size, type and other performance parameters. Clear Zero (Logic Low Level) Configuration Register Special purpose register which must be programmed to enable synchronous read mode Continuous Read Synchronous method of burst read whereby the device will read continuously until it is stopped by the host, or it has reached the highest address of the memory array, after which the read address wraps around to the lowest memory array address Erase Returns bits of a Flash memory array to their default state of a logical One (High Level). Erase Suspend/Erase Resume Halts an erase operation to allow reading or programming in any sector that is not selected for erasure BGA Ball Grid Array package. Spansion LLC offers two variations: Fortified Ball Grid Array and Fine-pitch Ball Grid Array. See the specific package drawing or connection diagram for further details. Linear Read Synchronous (burst) read operation in which 8, 16, or 32 words of sequential data with or without wraparound before requiring a new initial address. MCP Multi-Chip Package. A method of combining integrated circuits in a single package by “stacking” multiple die of the same or different devices. Memory Array The programmable area of the product available for data storage. MirrorBit™ Technology Spansion™ trademarked technology for storing multiple bits of data in the same transistor. 92 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y Term Definition Page Group of words that may be accessed more rapidly as a group than if the words were accessed individually. Page Read Asynchronous read operation of several words in which the first word of the group takes a longer initial access time and subsequent words in the group take less “page” access time to be read. Different words in the group are accessed by changing only the least significant address lines. Password Protection Sector protection method which uses a programmable password, in addition to the Persistent Protection method, for protection of sectors in the Flash memory device. Persistent Protection Sector protection method that uses commands and only the standard core voltage supply to control protection of sectors in the Flash memory device. This method replaces a prior technique of requiring a 12V supply to control the protection method. Program Stores data into a Flash memory by selectively clearing bits of the memory array in order to leave a data pattern of “ones” and “zeros”. Program Suspend/Program Resume Halts a programming operation to read data from any location that is not selected for programming or erase. Read Host bus cycle that causes the Flash to output data onto the data bus. Registers Dynamic storage bits for holding device control information or tracking the status of an operation. SecSi™ Secured Silicon. An area consisting of 256 bytes in which any word may be programmed once, and the entire area may be protected once from any future programming. Information in this area may be programmed at the factory or by the user. Once programmed and protected there is no way to change the secured information. This area is often used to store a software readable identification such as a serial number. Sector Protection Use of one or more control bits per sector to indicate whether each sector may be programmed or erased. If the Protection bit for a sector is set the embedded algorithms for program or erase will ignore program or erase commands related to that sector. Sector An Area of the memory array in which all bits must be erased together by an erase operation. Simultaneous Operation Mode of operation in which a host system may issue a program or erase command to one bank, that embedded algorithm operation may then proceed while the host immediately follows the embedded algorithm command with reading from another bank. Reading may continue concurrently in any bank other than the one executing the embedded algorithm operation. Synchronous Operation Operation that progresses only when a timing signal, known as a clock, transitions between logic levels (that is, at a clock edge). VersatileIO™ (VIO) Separate power supply or voltage reference signal that allows the host system to set the voltage levels that the device generates at its data outputs and the voltages tolerated at its data inputs. Unlock Bypass Mode that facilitates faster program times by reducing the number of command bus cycles required to issue a write operation command. In this mode the initial two “Unlock” write cycles, of the usual 4 cycle Program command, are not required – reducing all Program commands to two bus cycles while in this mode. Word Two contiguous bytes (16 bits) located at an even byte boundary. A double word is two contiguous words located on a two word boundary. A quad word is four contiguous words located on a four word boundary. October 29, 2004 S29WSxxxN_00_F0 93 P r e l i m i n a r y Term Definition Wraparound Special burst read mode where the read address “wraps” or returns back to the lowest address boundary in the selected range of words, after reading the last Byte or Word in the range, e.g. for a 4 word range of 0 to 3, a read beginning at word 2 would read words in the sequence 2, 3, 0, 1. Write Interchangeable term for a program/erase operation where the content of a register and or memory location is being altered. The term write is often associated with “writing command cycles” to enter or exit a particular mode of operation. Write Buffer Multi-word area in which multiple words may be programmed as a single operation. A Write Buffer may be 16 to 32 words long and is located on a 16 or 32 word boundary respectively. Write Buffer Programming Method of writing multiple words, up to the maximum size of the Write Buffer, in one operation. Using Write Buffer Programming will result in ≥ 8 times faster programming time than by using single word at a time programming commands. Write Operation Status Allows the host system to determine the status of a program or erase operation by reading several special purpose register bits. 94 S29WSxxxN_00_F0 October 29, 2004 P r e l i m i n a r y 14 Revisions Revision F (October 29, 2004) Data sheet completely revised. Changed arrangement of sections; edited explanatory text, added flowcharts. This document supersedes Revision E+1, issued August 9, 2004; only the changes specified for Revision F in this section affect the document or device. All other device specifications remain the same as presented in Revision E+1. Deleted product selector guide. 11.8.2, Synchronous/Burst Read Deleted tAAS and tAAH from table. Modified Note 1. Table 12.4, System Interface String Changed data at address 23h from 0003h to 0004h. Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor device has an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks and Notice The contents of this document are subject to change without notice.This document may contain information on a SpansionTM product under development by Spansion LLC. Spansion LLC reserves the right to change or discontinue work on any product without notice. The information in this document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion LLC assumes no liability for any damages of any kind arising out of the use of the information in this document. Copyright © 2004 Spansion LLC. All rights reserved. SpansionTM, the SpansionTM logo, MirrorBit, combinations thereof, and ExpressFlash are trademarks of Spansion LLC. Other company and product names used in this publication are for identification purposes only and may be trademarks of their respective companies. October 29, 2004 S29WSxxxN_00_F0 95