R&E International A Subsidiary of Microchip Technology Inc. RE46C108 Piezoelectric Horn Driver and Voltage Regulator Product Specification General Description Features The RE46C108 is a piezoelectric horn driver with a voltage regulator that can operate at 3.3V or 5V. It is intended for applications requiring a 9V horn driver with a low voltage logic supply. The horn feedback control pin is designed for use with selfoscillating piezoelectric horn but can also be used in direct drive applications. • • • • • Applications Smoke detectors CO Detectors Personal Security Products Electronic Toys Low Quiescent Current Low Horn Driver Ron Voltage Regulation to 3.3V or 5V Available in DIP and SOIC packaging Available in Standard Packaging or RoHS Compliant Pb Free Packaging Pin Configuration REGSEL 1 8 HRNEN VDD HORNS REGOUT HORNB FEED VSS Absolute maximum ratings Supply Voltage Vdd ........………………………………….......-.5V to +14V Input voltage Range Vin ...…………………………………..... -.3V to VDD+.3V, except FEED FEED Input Voltage Range Vinf …………………………...… -10V to +22V Input Current Iin ..............…………………………………..... 10mA, except FEED Operating Temperature .......………………………………….. -40 to 85°C Continuous Output Current (HornS, HornB) .……………….. 30mA Continuous Output Current (REGOUT) .…………………….. 55mA Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and operation at these conditions for extended periods may affect device reliability. This product utilizes CMOS technology with static protection; however proper ESD prevention procedures should be used when handling this product. Damage can occur when exposed to extremely high static electrical charges © 2009 Microchip Technology Inc. DS22165A-page 1 RE46C108 Piezoelectric Horn Driver and Voltage Regulator Product Specification R&E International A Subsidiary of Microchip Technology Inc. Electrical Characteristics at TA = 25°C, VDD = 9V, Vss = 0V (unless otherwise noted). Parameter Supply Voltage Standby Supply Current Input Leakage Input Voltage Low Input Voltage High Output Low Voltage Output High Voltage Regulator Voltage Line Regulation Load Regulation Brown-Out Threshold Voltage *See note #1 Brown-Out Pull Down Current Regout Overvoltage Clamp *See note #2 Test Pin Test Conditions Min Limits Typ Max Vdd Operating 6.0 9.0 Vdd Hrnen=Vss; No Loads Hrnen,Resel Vin=Vdd or Vss FEED Feed = +22V FEED Feed = -10V -100 20 -50 Horns or Hornb Regout Regout Regout Vdd Regout Regout uA 100 nA 50 uA uA 1.0 2.3 Iout=16mA; Vdd=9V Vdd=7.2V V V 0.3 8.5 6.3 4.75 3.10 V 4 -15 Hrnen, Regsel Hrnen, Regsel Horns or Hornb 13.8 Units Iout=-16mA; Vdd=9V Vdd=7.2V Iout<50mA; Regsel=Vdd Iout<50mA; Regsel=Vss TA=-40 to 85°C See note #3 6V<Vdd<12V; No load 0mA<Iout<20mA Regsel=Vdd or Vss Falling edge of Vdd Vdd=4.5V; Regout=2V 4.5 30 100 5.0 15 25 Regsel=Vdd; Iout > 1mA Regsel=Vss; Iout > 1mA 5.5 3.7 6.0 4.0 0.5 0.9 V V 5.25 3.50 V V V V 5.5 mV mV V 8.7 5.0 3.3 mA 6.5 4.3 V V Notes: 1/ The brown-out threshold voltage is the Vdd voltage at which the regulator will be disabled and Regout will be pulled to Vss. 2/ In normal operation, the regulator will provide high-side current of up to 20mA, but current sinking capability is typically under 1uA. The overvoltage clamp is intended to limit the voltage at Regout when it is pulled up by an external source. 3/ The limits shown are 100% tested at 25C only. Test limits are guard-banded based on temperature characterization to guarantee compliance at temperature extremes. © 2009 Microchip Technology Inc. DS22165A-page 2 RE46C108 Piezoelectric Horn Driver and Voltage Regulator Product Specification R&E International A Subsidiary of Microchip Technology Inc. Typical Application Functional Block Diagram VDD 2 REGSEL 1 Bandgap Reference 3 REGOUT 4 FEED Output Adjust Clamp & Shutdown Circuit HRNEN 8 VSS 5 © 2009 Microchip Technology Inc. 7 6 HORNS HORNB DS22165A-page 3 RE46C108 Piezoelectric Horn Driver and Voltage Regulator Product Specification R&E International A Subsidiary of Microchip Technology Inc. Trademarks Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC, SmartShunt and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, nanoWatt XLP, PICkit, PICDEM, 32 logo, PowerCal, PowerInfo, PICDEM.net, PICtail, PIC PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2009 Microchip Technology Inc. DS22165A-page 4