AMD AM29LV128ML103RPCI

Am29LV128MH/L
Data Sheet
July 2003
The following document specifies Spansion memory products that are now offered by both Advanced
Micro Devices and Fujitsu. Although the document is marked with the name of the company that originally developed the specification, these products will be offered to customers of both AMD and
Fujitsu.
Continuity of Specifications
There is no change to this datasheet as a result of offering the device as a Spansion product. Any
changes that have been made are the result of normal datasheet improvement and are noted in the
document revision summary, where supported. Future routine revisions will occur when appropriate,
and changes will be noted in a revision summary.
Continuity of Ordering Part Numbers
AMD and Fujitsu continue to support existing part numbers beginning with “Am” and “MBM”. To order
these products, please use only the Ordering Part Numbers listed in this document.
For More Information
Please contact your local AMD or Fujitsu sales office for additional information about Spansion
memory solutions.
Publication Number 25270 Revision C
Amendment +2 Issue Date September 9, 2003
THIS PAGE LEFT INTENTIONALLY BLANK.
DATASHEET
Am29LV128MH/L
128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit™ 3.0 Volt-only
Uniform Sector Flash Memory with VersatileI/O™ Control
DISTINCTIVE CHARACTERISTICS
ARCHITECTURAL ADVANTAGES
■ Single power supply operation
— 3 volt read, erase, and program operations
■ VersatileI/O™ control
— Device generates data output voltages and tolerates
data input voltages on the CE# and DQ
inputs/outputs as determined by the voltage on the
VIO pin; operates from 1.65 to 3.6 V
■ Manufactured on 0.23 µm MirrorBit process
technology
■ SecSi™ (Secured Silicon) Sector region
— 128-word/256-byte sector for permanent, secure
identification through an 8-word/16-byte random
Electronic Serial Number, accessible through a
command sequence
— May be programmed and locked at the factory or by
the customer
■ Flexible sector architecture
— Two hundred fifty-six 32 Kword (64 Kbyte) sectors
■ Compatibility with JEDEC standards
— Provides pinout and software compatibility for
single-power supply flash, and superior inadvertent
write protection
■ Minimum 100,000 erase cycle guarantee per sector
■ 20-year data retention at 125°C
PERFORMANCE CHARACTERISTICS
■ High performance
— 90 ns access time
— 25 ns page read times
— 0.5 s typical sector erase time
— 15 s typical effective write buffer word programming
time: 16-word/32-byte write buffer reduces overall
programming time for multiple-word updates
— 4-word/8-byte page read buffer
— 16-word/32-byte write buffer
■ Low power consumption (typical values at 3.0 V, 5
MHz)
— 13 mA typical active read current
— 50 mA typical erase/program current
— 1 µA typical standby mode current
■ Package options
— 56-pin TSOP
— 64-ball Fortified BGA
SOFTWARE & HARDWARE FEATURES
■ Software features
— Program Suspend & Resume: read other sectors
before programming operation is completed
— Erase Suspend & Resume: read/program other
sectors before an erase operation is completed
— Data# polling & toggle bits provide status
— Unlock Bypass Program command reduces overall
multiple-word or byte programming time
— CFI (Common Flash Interface) compliant: allows host
system to identify and accommodate multiple flash
devices
■ Hardware features
— Sector Group Protection: hardware-level method of
preventing write operations within a sector group
— Temporary Sector Group Unprotect: VID-level method
of changing code in locked sector groups
— WP#/ACC input accelerates programming time
(when high voltage is applied) for greater throughput
during system production. Protects first or last sector
regardless of sector protection settings
— Hardware reset input (RESET#) resets device
— Ready/Busy# output (RY/BY#) detects program or
erase cycle completion
This Data Sheet states AMD’s current technical specifications regarding the Products described herein. This Data
Sheet may be revised by subsequent versions or modifications due to changes in technical specifications.
Publication# 25270 Rev: C Amendment/2
Issue Date: September 9, 2003
Refer to AMD’s Website (www.amd.com) for the latest information.
D A T A S H E E T
GENERAL DESCRIPTION
The Am29LV128MH/L is a 128 Mbit, 3.0 volt single
power supply flash memory devices organized as
8,388,608 words or 16,777,216 bytes. The device has
a 16-bit wide data bus that can also function as an
8-bit wide data bus by using the BYTE# input. The device can be programmed either in the host system or
in standard EPROM programmers.
An access time of 90, 100, 110, or 120 ns is available.
Note that each access time has a specific operating
voltage range (VCC) and an I/O voltage range (VIO), as
specified in the Product Selector Guide and the Ordering Information sections. The device is offered in a
56-pin TSOP, 64-ball Fortified BGA. Each device has
separate chip enable (CE#), write enable (WE#) and
output enable (OE#) controls.
Each device requires only a single 3.0 volt power
supply for both read and write functions. In addition to
a V CC input, a high-voltage accelerated program
(WP#/ACC) input provides shorter programming times
through increased current. This feature is intended to
facilitate factory throughput during system production,
but may also be used in the field if desired.
The device is entirely command set compatible with
the JEDEC single-power-supply Flash standard.
Commands are written to the device using standard
microprocessor write timing. Write cycles also internally latch addresses and data needed for the programming and erase operations.
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting
the data contents of other sectors. The device is fully
erased when shipped from the factory.
Device programming and erasure are initiated through
command sequences. Once a program or erase operation has begun, the host system need only poll the
DQ7 (Data# Polling) or DQ6 (toggle) status bits or
monitor the Ready/Busy# (RY/BY#) output to determine whether the operation is complete. To facilitate
programming, an Unlock Bypass mode reduces command sequence overhead by requiring only two write
cycles to program data instead of four.
The VersatileI/O™ (VIO) control allows the host system to set the voltage levels that the device generates
and tolerates on the CE# control input and DQ I/Os to
the same voltage level that is asserted on the VIO pin.
Refer to the Ordering Information section for valid VIO
options.
Hardware data protection measures include a low
V CC detector that automatically inhibits write operations during power transitions. The hardware sector
group protection feature disables both program and
erase operations in any combination of sector groups
of memory. This can be achieved in-system or via programming equipment.
The Erase Suspend/Erase Resume feature allows
the host system to pause an erase operation in a given
sector to read or program any other sector and then
complete the erase operation. The Program Suspend/Program Resume feature enables the host system to pause a program operation in a given sector to
read any other sector and then complete the program
operation.
The hardware RESET# pin terminates any operation
in progress and resets the device, after which it is then
ready for a new operation. The RESET# pin may be
tied to the system reset circuitry. A system reset would
thus also reset the device, enabling the host system to
read boot-up firmware from the Flash memory device.
The device reduces power consumption in the
standby mode when it detects specific voltage levels
on CE# and RESET#, or when addresses have been
stable for a specified period of time.
The SecSi ™ (Secured Silicon) Sector provides a
128-word/256-byte area for code or data that can be
permanently protected. Once this sector is protected,
no further changes within the sector can occur.
The Write Protect (WP#/ACC) feature protects the
first or last sector by asserting a logic low on the WP#
pin.
AMD MirrorBit flash technology combines years of
Flash memory manufacturing experience to produce
the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a
sector simultaneously via hot-hole assisted erase. The
data is programmed using hot electron injection.
RELATED DOCUMENTS
For a comprehensive information on MirrorBit products, including migration information, data sheets, application notes, and software drivers, please see
www.amd.com → Flash Memory → Product Information→MirrorBit→Flash Information→Technical Documentation. The following is a partial list of documents
closely related to this product:
2
MirrorBit™ Flash Memory Write Buffer Programming
and Page Buffer Read
Implementing a Common Layout for AMD MirrorBit
and Intel StrataFlash Memory Devices
Migrating from Single-byte to Three-byte Device IDs
Am29LV256M, 256 Mbit MirrorBit Flash device
(in 64-ball, 18 x 12 mm Fortified BGA package)
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
TABLE OF CONTENTS
Product Selector Guide . . . . . . . . . . . . . . . . . . . . .
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . .
Pin Description. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . . .
Device Bus Operations . . . . . . . . . . . . . . . . . . . . .
4
4
5
7
7
8
9
Table 1. Device Bus Operations ....................................................... 9
Word/Byte Configuration .......................................................... 9
VersatileIO™ (VIO) Control ....................................................... 9
Requirements for Reading Array Data ................................... 10
Page Mode Read ............................................................................10
Writing Commands/Command Sequences ............................ 10
Write Buffer .....................................................................................10
Accelerated Program Operation ......................................................10
Autoselect Functions .......................................................................10
Standby Mode ........................................................................ 10
Automatic Sleep Mode ........................................................... 11
RESET#: Hardware Reset Pin ............................................... 11
Output Disable Mode .............................................................. 11
Table 2. Sector Address Table........................................................ 12
Autoselect Mode ..................................................................... 18
Erase Suspend/Erase Resume Commands ........................... 33
Command Definitions ............................................................. 34
Table 10. Command Definitions (x16 Mode, BYTE# = VIH) ........... 34
Table 11. Command Definitions (x8 Mode, BYTE# = VIL).............. 35
Write Operation Status . . . . . . . . . . . . . . . . . . . . . 36
DQ7: Data# Polling ................................................................. 36
Figure 8. Data# Polling Algorithm .................................................. 36
RY/BY#: Ready/Busy# ............................................................ 37
DQ6: Toggle Bit I .................................................................... 37
Figure 9. Toggle Bit Algorithm ........................................................ 38
DQ2: Toggle Bit II ................................................................... 38
Reading Toggle Bits DQ6/DQ2 ............................................... 38
DQ5: Exceeded Timing Limits ................................................ 39
DQ3: Sector Erase Timer ....................................................... 39
DQ1: Write-to-Buffer Abort ..................................................... 39
Table 12. Write Operation Status................................................... 40
Absolute Maximum Ratings. . . . . . . . . . . . . . . . . 41
Figure 10. Maximum Negative Overshoot Waveform ................... 41
Figure 11. Maximum Positive Overshoot Waveform ..................... 41
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 41
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 42
Test Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Sector Group Protection and Unprotection ............................. 19
Figure 12. Test Setup .................................................................... 43
Table 13. Test Specifications ......................................................... 43
Table 4. Sector Group Protection/Unprotection Address Table ..... 19
Key to Switching Waveforms. . . . . . . . . . . . . . . . 43
Table 3. Autoselect Codes, (High Voltage Method) ....................... 18
Write Protect (WP#) ................................................................ 20
Temporary Sector Group Unprotect ....................................... 20
Figure 1. Temporary Sector Group Unprotect Operation ................20
Figure 2. In-System Sector Group Protect/Unprotect Algorithms ...21
SecSi (Secured Silicon) Sector Flash Memory Region .......... 22
Figure 13. Input Waveforms and Measurement Levels ................. 43
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 44
Read-Only Operations ........................................................... 44
Figure 14. Read Operation Timings ............................................... 44
Figure 15. Page Read Timings ...................................................... 45
Table 5. SecSi Sector Contents ...................................................... 22
Figure 3. SecSi Sector Protect Verify ..............................................23
Hardware Reset (RESET#) .................................................... 46
Hardware Data Protection ...................................................... 23
Erase and Program Operations .............................................. 47
Low VCC Write Inhibit .....................................................................23
Write Pulse “Glitch” Protection ........................................................23
Logical Inhibit ..................................................................................23
Power-Up Write Inhibit ....................................................................23
Figure 17. Reset Timings ............................................................... 48
Figure 18. Program Operation Timings .......................................... 49
Figure 19. Accelerated Program Timing Diagram .......................... 49
Figure 20. Chip/Sector Erase Operation Timings .......................... 50
Figure 21. Data# Polling Timings (During Embedded Algorithms) . 51
Figure 22. Toggle Bit Timings (During Embedded Algorithms) ...... 52
Figure 23. DQ2 vs. DQ6 ................................................................. 52
Common Flash Memory Interface (CFI) . . . . . . . 23
Table 6. CFI Query Identification String ..........................................24
Table 7. System Interface String..................................................... 24
Table 8. Device Geometry Definition ..............................................25
Table 9. Primary Vendor-Specific Extended Query ........................26
Command Definitions . . . . . . . . . . . . . . . . . . . . . 27
Reading Array Data ................................................................ 27
Reset Command ..................................................................... 27
Autoselect Command Sequence ............................................ 27
Enter SecSi Sector/Exit SecSi Sector Command Sequence .. 28
Word/Byte Program Command Sequence ............................. 28
Unlock Bypass Command Sequence ..............................................28
Write Buffer Programming ...............................................................28
Accelerated Program ......................................................................29
Figure 4. Write Buffer Programming Operation ...............................30
Figure 5. Program Operation ..........................................................31
Program Suspend/Program Resume Command Sequence ... 31
Figure 6. Program Suspend/Program Resume ...............................32
Chip Erase Command Sequence ........................................... 32
Sector Erase Command Sequence ........................................ 32
Figure 16. Reset Timings ............................................................... 46
Temporary Sector Group Unprotect ....................................... 53
Figure 24. Temporary Sector Group Unprotect Timing Diagram ... 53
Figure 25. Sector Group Protect and Unprotect Timing Diagram .. 54
Alternate CE# Controlled Erase and Program Operations ..... 55
Figure 26. Alternate CE# Controlled Write (Erase/Program)
Operation Timings .......................................................................... 56
Latchup Characteristics . . . . . . . . . . . . . . . . . . . . 56
Erase And Programming Performance. . . . . . . . 57
TSOP Pin and BGA Package Capacitance . . . . . 58
Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 59
TS056/TSR056—56-Pin Standard/Reverse Thin Small Outline
Package (TSOP) ..................................................................... 59
LAA064—64-Ball Fortified Ball Grid Array
13 x 11 mm Package .............................................................. 60
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 7. Erase Operation ...............................................................33
September 9, 2003
Am29LV128MH/L
3
D A T A S H E E T
PRODUCT SELECTOR GUIDE
Part Number
Speed/
Voltage
Option
Regulated Voltage Range
VCC = 3.0–3.6 V
Am29LV128MH/L
103R
113R
93R
VIO = 3.0–3.6 V VIO = 2.7–3.6 V VIO = 1.65–3.6 V
113
(Note 2)
VIO = 1.65–3.6 V
103
(Note 2)
VIO = 2.7–3.6 V
Full Voltage Range
VCC = 2.7–3.6 V
123R
VIO = 1.65–3.6 V
123
(Note 2)
VIO = 1.65–3.6 V
Max. Access Time (ns)
90
100
110
120
Max. CE# Access Time (ns)
90
100
110
120
Max. Page access time (tPACC)
25
30
30
40
30
40
Max. OE# Access Time (ns)
25
30
30
40
30
40
Notes:
1.
See “AC Characteristics” for full specifications.
2. Contact factory for availability and ordering information.
BLOCK DIAGRAM
DQ0–DQ15 (A-1)
RY/BY#
VCC
Sector Switches
VSS
VIO
Erase Voltage
Generator
Input/Output
Buffers
RESET#
WE#
WP#/ACC
BYTE#
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
VCC Detector
A22–A0
4
Timer
Address Latch
STB
Am29LV128MH/L
STB
Data
Latch
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
September 9, 2003
D A T A S H E E T
CONNECTION DIAGRAMS
NC
A22
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
A21
WP#/ACC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
NC
NC
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
NC
VIO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
September 9, 2003
56-Pin Standard TSOP
56-Pin Reverse TSOP
Am29LV128MH/L
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
NC
NC
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
NC
VIO
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
NC
A22
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
A21
WP#/ACC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
NC
NC
5
D A T A S H E E T
CONNECTION DIAGRAMS
64- Ball Fortified BGA
Top View, Balls Facing Down
A8
B8
C8
D8
E8
F8
G8
H8
NC
A22
NC
VIO
VSS
NC
NC
NC
A7
B7
C7
D7
E7
F7
G7
H7
A13
A12
A14
A15
A16
A6
B6
C6
D6
E6
F6
G6
H6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
A5
B5
C5
D5
E5
F5
G5
H5
WE#
RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
A4
B4
C4
D4
E4
F4
G4
H4
A18
A20
DQ2
DQ10
DQ11
DQ3
RY/BY# WP#/ACC
BYTE# DQ15/A-1
VSS
A3
B3
C3
D3
E3
F3
G3
H3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A2
B2
C2
D2
E2
F2
G2
H2
A3
A4
A2
A1
A0
CE#
OE#
VSS
A1
B1
C1
D1
E1
F1
G1
H1
NC
NC
NC
NC
NC
VIO
NC
NC
Special Package Handling Instructions
package body is exposed to temperatures above
150°C for prolonged periods of time.
Special handling is required for Flash Memory products
in molded packages (TSOP and BGA). The package
and/or data integrity may be compromised if the
6
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
PIN DESCRIPTION
A22–A0
LOGIC SYMBOL
= 23 Address inputs
23
DQ14–DQ0 = 15 Data inputs/outputs
A22–A0
DQ15/A-1
= DQ15 (Data input/output, word mode),
A-1 (LSB Address input, byte mode)
CE#
CE#
= Chip Enable input
OE#
OE#
= Output Enable input
WE#
WE#
= Write Enable input
WP#/ACC
WP#/ACC
= Hardware Write Protect input;
Acceleration input
RESET#
RESET#
= Hardware Reset Pin input
BYTE#
= Selects 8-bit or 16-bit mode
RY/BY#
= Ready/Busy output
VCC
= 3.0 volt-only single power supply
(see Product Selector Guide for
speed options and voltage
supply tolerances)
VIO
= Output Buffer power
VSS
= Device Ground
NC
= Pin Not Connected Internally
September 9, 2003
VIO
16 or 8
DQ15–DQ0
(A-1)
RY/BY#
BYTE#
Am29LV128MH/L
7
D A T A S H E E T
ORDERING INFORMATION
Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is
formed by a combination of the following:
Am29LV128MH/L
H
123R
PC
I
TEMPERATURE RANGE
I
= Industrial (–40°C to +85°C)
PACKAGE TYPE
E
= 56-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 056)
F
= 56-Pin Thin Small Outline Package (TSOP) Reverse Pinout (TSR056)
PC = 64-Ball Fortified Ball Grid Array (FBGA),
1.0 mm pitch, 13 x 11 mm package (LAA064)
SPEED OPTION
See Product Selector Guide and Valid Combinations
SECTOR ARCHITECTURE AND SECTOR WRITE PROTECTION (WP# = VIL)
H
= Uniform sector device, highest address sector protected
L
= Uniform sector device, lowest address sector protected
DEVICE NUMBER/DESCRIPTION
Am29LV128MH/L
128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit Uniform Sector Flash Memory with VersatileIO™ Control,
3.0 Volt-only Read, Program, and Erase
Valid Combinations for
TSOP Package
Am29LV128MH93R
Am29LV128ML93R
Am29LV128MH103R
Am29LV128ML103R
Am29LV128MH113R
Am29LV128ML113R
Am29LV128MH123R
Am29LV128ML123R
EI,
FI
Speed
(ns)
VIO
Range
90
3.0–3.6 V
100
2.7–3.6 V
110
1.65–3.6 V
VCC
Range
Order Number
Package Marking
Am29LV128MH93R
Am29LV128ML93R
3.0–3.6 V
120
Valid Combinations for
Fortified BGA Package
Am29LV128MH103R
Am29LV128ML103R
Am29LV128MH113R
Am29LV128ML113R
1.65–3.6 V
Am29LV128MH123R
Am29LV128ML123R
Valid Combinations
L128MH93N
L128ML93N
PCI
L128MH103N
L128ML103N
L128MH113N
L128ML113N
L128MH123N
L128ML123N
VCC
Speed
VIO
Range Range
(ns)
90
3.0–
3.6V
100
2.7–
3.6 V
110
1.65–
3.6 V
120
1.65–
3.6 V
I
3.0–
3.6 V
Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm
availability of specific valid combinations and to check on newly released combinations.
Notes:
1. For 100, 110, and 120 speed option shown in product selector guide, contact AMD for availability and ordering information.
2.
8
To select product with ESN factory-locked into the SecSi Sector: 1) select order number from the valid combinations given above, 2) add designator “N” at the
end of the order number, and 3) modify the speed option indicator as follows [103R = 10R, 113R = 11R, 123R = 12R, 93R, 103, 113, 123 = no change].
Example: Am29LV128MH12RPCIN. For Fortified BGA pacakges, modify the speed option indicator as follows: [103N = 10N, 113N = 11N, 123N = 12N, 93N =
no change]. The designator “N” will also appear at the end of the package marking. Example: L128MH12NIN.
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
DEVICE BUS OPERATIONS
This section describes the requirements and use of
the device bus operations, which are initiated through
the internal command register. The command register
itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information
needed to execute the command. The contents of the
Table 1.
register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the
device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting
output. The following subsections describe each of
these operations in further detail.
Device Bus Operations
DQ8–DQ15
CE#
OE#
WE#
RESET#
WP#
ACC
Addresses
(Note 2)
DQ0–
DQ7
BYTE#
= VIH
Read
L
L
H
H
X
X
AIN
DOUT
DOUT
Write (Program/Erase)
L
H
L
H
(Note 3)
X
AIN
(Note 4) (Note 4)
Accelerated Program
L
H
L
H
(Note 3)
VHH
AIN
(Note 4) (Note 4)
VCC ±
0.3 V
X
X
VCC ±
0.3 V
X
H
X
High-Z
High-Z
High-Z
Output Disable
L
H
H
H
X
X
X
High-Z
High-Z
High-Z
Reset
X
X
X
L
X
X
X
High-Z
High-Z
High-Z
Sector Group Protect
(Note 2)
L
H
L
VID
H
X
SA, A6 =L,
A3=L, A2=L,
A1=H, A0=L
(Note 4)
X
X
Sector Group Unprotect
(Note 2)
L
H
L
VID
H
X
SA, A6=H,
A3=L, A2=L,
A1=H, A0=L
(Note 4)
X
X
Temporary Sector Group
Unprotect
X
X
X
VID
H
X
AIN
Operation
Standby
(Note 4) (Note 4)
BYTE#
= VIL
DQ8–DQ14
= High-Z,
DQ15 = A-1
High-Z
Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector Address,
AIN = Address In, DIN = Data In, DOUT = Data Out
Notes:
1. Addresses are A22:A0 in word mode; A22:A-1 in byte mode. Sector addresses are A22:A15 in both modes.
2. The sector group protect and sector group unprotect functions may also be implemented via programming equipment. See the
“Sector Group Protection and Unprotection” section.
3. If WP# = VIL, the first or last sector remains protected. If WP# = VIH, the first or last sector will be protected or unprotected as
determined by the method described in “Write Protect (WP#)”. All sectors are unprotected when shipped from the factory (The
SecSi Sector may be factory protected depending on version ordered.)
4. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see Figure 2).
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O
pins operate in the byte or word configuration. If the
BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ0–DQ15 are active and controlled by
CE# and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte
configuration, and only data I/O pins DQ0–DQ7 are
active and controlled by CE# and OE#. The data I/O
September 9, 2003
pins DQ8–DQ14 are tri-stated, and the DQ15 pin is
used as an input for the LSB (A-1) address function.
VersatileIO™ (VIO) Control
The VersatileIO™ (VIO) control allows the host system
to set the voltage levels that the device generates and
tolerates on CE# and DQ I/Os to the same voltage
level that is asserted on VIO. See Ordering Information
for VIO options on this device.
Am29LV128MH/L
9
D A T A S H E E T
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output control and gates array data to the output pins. WE#
should remain at VIH.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No command is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid
data on the device data outputs. The device remains
enabled for read access until the command register
contents are altered.
See “Reading Array Data” for more information. Refer
to the AC Read-Only Operations table for timing specifications and to Figure 14 for the timing diagram. Refer
to the DC Characteristics table for the active current
specification on reading array data.
Page Mode Read
The device is capable of fast page mode read and is
compatible with the page mode Mask ROM read operation. This mode provides faster read access speed
for random locations within a page. The page size of
the device is 4 words/8 bytes. The appropriate page is
selected by the higher address bits A(max)–A2. Address bits A1–A0 in word mode (A1–A-1 in byte mode)
determine the specific word within a page. This is an
asynchronous operation; the microprocessor supplies
the specific word location.
The random or initial page access is equal to tACC or
tCE and subsequent page read accesses (as long as
the locations specified by the microprocessor falls
within that page) is equivalent to tPACC. When CE# is
deasserted and reasserted for a subsequent access,
the access time is t ACC or t CE . Fast page mode accesses are obtained by keeping the “read-page addresses” constant and changing the “intra-read page”
addresses.
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the
Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The
“Word/Byte Program Command Sequence” section
has details on programming data to the device using
10
both standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device. Table 2 indicates the address
space that each sector occupies.
Refer to the DC Characteristics table for the active
current specification for the write mode. The AC Characteristics section contains timing specification tables
and timing diagrams for write operations.
Write Buffer
Write Buffer Programming allows the system write to a
maximum of 16 words/32 bytes in one programming
operation. This results in faster effective programming
time than the standard programming algorithms. See
“Write Buffer” for more information.
Accelerated Program Operation
The device offers accelerated program operations
through the ACC function. This is one of two functions
provided by the WP#/ACC pin. This function is primarily intended to allow faster manufacturing throughput
at the factory.
If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass
mode, temporarily unprotects any protected sector
groups, and uses the higher voltage on the pin to reduce the time required for program operations. The
system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device
to normal operation. Note that the WP#/ACC pin must
not be at VHH for operations other than accelerated
programming, or device damage may result. WP# has
an internal pullup; when unconnected, WP# is at VIH.
Autoselect Functions
If the system writes the autoselect command sequence, the device enters the autoselect mode. The
system can then read autoselect codes from the internal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in
this mode. Refer to the Autoselect Mode and Autoselect Command Sequence sections for more information.
Standby Mode
When the system is not reading or writing to the device, it can place the device in the standby mode. In
this mode, current consumption is greatly reduced,
and the outputs are placed in the high impedance
state, independent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at VIO ± 0.3 V.
(Note that this is a more restricted voltage range than
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
VIH.) If CE# and RESET# are held at VIH, but not within
VIO ± 0.3 V, the device will be in the standby mode, but
the standby current will be greater. The device requires standard access time (t CE ) for read access
when the device is in either of these standby modes,
before it is ready to read data.
If the device is deselected during erasure or programming, the device draws active current until the
operation is completed.
Refer to the DC Characteristics table for the standby
current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables
this mode when addresses remain stable for t ACC +
30 ns. The automatic sleep mode is independent of
the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output
data is latched and always available to the system.
Refer to the DC Characteristics table for the automatic
sleep mode current specification.
RESET#: Hardware Reset Pin
SET# pin is driven low for at least a period of tRP, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is
ready to accept another command sequence, to ensure data integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VSS±0.3 V, the device
draws CMOS standby current (ICC4). If RESET# is held
at VIL but not within VSS±0.3 V, the standby current will
be greater.
The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firmware from the Flash memory.
Refer to the AC Characteristics tables for RESET# parameters and to Figure 16 for the timing diagram.
Output Disable Mode
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high
impedance state.
The RESET# pin provides a hardware method of resetting the device to reading array data. When the RE-
September 9, 2003
Am29LV128MH/L
11
D A T A S H E E T
Table 2.
Sector
12
Sector Address Table
A22–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA0
0
0
0
0
0
0
0
0
64/32
000000–00FFFF
000000–007FFF
SA1
0
0
0
0
0
0
0
1
64/32
010000–01FFFF
008000–00FFFF
SA2
0
0
0
0
0
0
1
0
64/32
020000–02FFFF
010000–017FFF
SA3
0
0
0
0
0
0
1
1
64/32
030000–03FFFF
018000–01FFFF
SA4
0
0
0
0
0
1
0
0
64/32
040000–04FFFF
020000–027FFF
SA5
0
0
0
0
0
1
0
1
64/32
050000–05FFFF
028000–02FFFF
SA6
0
0
0
0
0
1
1
0
64/32
060000–06FFFF
030000–037FFF
SA7
0
0
0
0
0
1
1
1
64/32
070000–07FFFF
038000–03FFFF
SA8
0
0
0
0
1
0
0
0
64/32
080000–08FFFF
040000–047FFF
048000–04FFFF
SA9
0
0
0
0
1
0
0
1
64/32
090000–09FFFF
SA10
0
0
0
0
1
0
1
0
64/32
0A0000–0AFFFF
050000–057FFF
SA11
0
0
0
0
1
0
1
1
64/32
0B0000–0BFFFF
058000–05FFFF
SA12
0
0
0
0
1
1
0
0
64/32
0C0000–0CFFFF
060000–067FFF
SA13
0
0
0
0
1
1
0
1
64/32
0D0000–0DFFFF
068000–06FFFF
SA14
0
0
0
0
1
1
1
0
64/32
0E0000–0EFFFF
070000–077FFF
SA15
0
0
0
0
1
1
1
1
64/32
0F0000–0FFFFF
078000–07FFFF
SA16
0
0
0
1
0
0
0
0
64/32
100000–10FFFF
080000–087FFF
SA17
0
0
0
1
0
0
0
1
64/32
110000–11FFFF
088000–08FFFF
SA18
0
0
0
1
0
0
1
0
64/32
120000–12FFFF
090000–097FFF
SA19
0
0
0
1
0
0
1
1
64/32
130000–13FFFF
098000–09FFFF
SA20
0
0
0
1
0
1
0
0
64/32
140000–14FFFF
0A0000–0A7FFF
SA21
0
0
0
1
0
1
0
1
64/32
150000–15FFFF
0A8000–0AFFFF
SA22
0
0
0
1
0
1
1
0
64/32
160000–16FFFF
0B0000–0B7FFF
SA23
0
0
0
1
0
1
1
1
64/32
170000–17FFFF
0B8000–0BFFFF
SA24
0
0
0
1
1
0
0
0
64/32
180000–18FFFF
0C0000–0C7FFF
SA25
0
0
0
1
1
0
0
1
64/32
190000–19FFFF
0C8000–0CFFFF
SA26
0
0
0
1
1
0
1
0
64/32
1A0000–1AFFFF
0D0000–0D7FFF
SA27
0
0
0
1
1
0
1
1
64/32
1B0000–1BFFFF
0D8000–0DFFFF
SA28
0
0
0
1
1
1
0
0
64/32
1C0000–1CFFFF
0E0000–0E7FFF
SA29
0
0
0
1
1
1
0
1
64/32
1D0000–1DFFFF
0E8000–0EFFFF
SA30
0
0
0
1
1
1
1
0
64/32
1E0000–1EFFFF
0F0000–0F7FFF
SA31
0
0
0
1
1
1
1
1
64/32
1F0000–1FFFFF
0F8000–0FFFFF
SA32
0
0
1
0
0
0
0
0
64/32
200000–20FFFF
100000–107FFF
SA33
0
0
1
0
0
0
0
1
64/32
210000–21FFFF
108000–10FFFF
SA34
0
0
1
0
0
0
1
0
64/32
220000–22FFFF
110000–117FFF
SA35
0
0
1
0
0
0
1
1
64/32
230000–23FFFF
118000–11FFFF
SA36
0
0
1
0
0
1
0
0
64/32
240000–24FFFF
120000–127FFF
SA37
0
0
1
0
0
1
0
1
64/32
250000–25FFFF
128000–12FFFF
SA38
0
0
1
0
0
1
1
0
64/32
260000–26FFFF
130000–137FFF
SA39
0
0
1
0
0
1
1
1
64/32
270000–27FFFF
138000–13FFFF
SA40
0
0
1
0
1
0
0
0
64/32
280000–28FFFF
140000–147FFF
SA41
0
0
1
0
1
0
0
1
64/32
290000–29FFFF
148000–14FFFF
SA42
0
0
1
0
1
0
1
0
64/32
2A0000–2AFFFF
150000–157FFF
SA43
0
0
1
0
1
0
1
1
64/32
2B0000–2BFFFF
158000–15FFFF
SA44
0
0
1
0
1
1
0
0
64/32
2C0000–2CFFFF
160000–167FFF
SA45
0
0
1
0
1
1
0
1
64/32
2D0000–2DFFFF
168000–16FFFF
SA46
0
0
1
0
1
1
1
0
64/32
2E0000–2EFFFF
170000–177FFF
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Table 2.
Sector
Sector Address Table (Continued)
A22–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA47
0
0
1
0
1
1
1
1
64/32
2F0000–2FFFFF
178000–17FFFF
SA48
0
0
1
1
0
0
0
0
64/32
300000–30FFFF
180000–187FFF
SA49
0
0
1
1
0
0
0
1
64/32
310000–31FFFF
188000–18FFFF
SA50
0
0
1
1
0
0
1
0
64/32
320000–32FFFF
190000–197FFF
SA51
0
0
1
1
0
0
1
1
64/32
330000–33FFFF
198000–19FFFF
SA52
0
0
1
1
0
1
0
0
64/32
340000–34FFFF
1A0000–1A7FFF
SA53
0
0
1
1
0
1
0
1
64/32
350000–35FFFF
1A8000–1AFFFF
SA54
0
0
1
1
0
1
1
0
64/32
360000–36FFFF
1B0000–1B7FFF
SA55
0
0
1
1
0
1
1
1
64/32
370000–37FFFF
1B8000–1BFFFF
SA56
0
0
1
1
1
0
0
0
64/32
380000–38FFFF
1C0000–1C7FFF
SA57
0
0
1
1
1
0
0
1
64/32
390000–39FFFF
1C8000–1CFFFF
SA58
0
0
1
1
1
0
1
0
64/32
3A0000–3AFFFF
1D0000–1D7FFF
SA59
0
0
1
1
1
0
1
1
64/32
3B0000–3BFFFF
1D8000–1DFFFF
SA60
0
0
1
1
1
1
0
0
64/32
3C0000–3CFFFF
1E0000–1E7FFF
SA61
0
0
1
1
1
1
0
1
64/32
3D0000–3DFFFF
1E8000–1EFFFF
SA62
0
0
1
1
1
1
1
0
64/32
3E0000–3EFFFF
1F0000–1F7FFF
SA63
0
0
1
1
1
1
1
1
64/32
3F0000–3FFFFF
1F8000–1FFFFF
SA64
0
1
0
0
0
0
0
0
64/32
400000–40FFFF
200000–207FFF
SA65
0
1
0
0
0
0
0
1
64/32
410000–41FFFF
208000–20FFFF
SA66
0
1
0
0
0
0
1
0
64/32
420000–42FFFF
210000–217FFF
SA67
0
1
0
0
0
0
1
1
64/32
430000–43FFFF
218000–21FFFF
SA68
0
1
0
0
0
1
0
0
64/32
440000–44FFFF
220000–227FFF
SA69
0
1
0
0
0
1
0
1
64/32
450000–45FFFF
228000–22FFFF
SA70
0
1
0
0
0
1
1
0
64/32
460000–46FFFF
230000–237FFF
SA71
0
1
0
0
0
1
1
1
64/32
470000–47FFFF
238000–23FFFF
SA72
0
1
0
0
1
0
0
0
64/32
480000–48FFFF
240000–247FFF
SA73
0
1
0
0
1
0
0
1
64/32
490000–49FFFF
248000–24FFFF
SA74
0
1
0
0
1
0
1
0
64/32
4A0000–4AFFFF
250000–257FFF
SA75
0
1
0
0
1
0
1
1
64/32
4B0000–4BFFFF
258000–25FFFF
SA76
0
1
0
0
1
1
0
0
64/32
4C0000–4CFFFF
260000–267FFF
SA77
0
1
0
0
1
1
0
1
64/32
4D0000–4DFFFF
268000–26FFFF
SA78
0
1
0
0
1
1
1
0
64/32
4E0000–4EFFFF
270000–277FFF
SA79
0
1
0
0
1
1
1
1
64/32
4F0000–4FFFFF
278000–27FFFF
SA80
0
1
0
1
0
0
0
0
64/32
500000–50FFFF
280000–287FFF
SA81
0
1
0
1
0
0
0
1
64/32
510000–51FFFF
288000–28FFFF
SA82
0
1
0
1
0
0
1
0
64/32
520000–52FFFF
290000–297FFF
SA83
0
1
0
1
0
0
1
1
64/32
530000–53FFFF
298000–29FFFF
SA84
0
1
0
1
0
1
0
0
64/32
540000–54FFFF
2A0000–2A7FFF
SA85
0
1
0
1
0
1
0
1
64/32
550000–55FFFF
2A8000–2AFFFF
SA86
0
1
0
1
0
1
1
0
64/32
560000–56FFFF
2B0000–2B7FFF
SA87
0
1
0
1
0
1
1
1
64/32
570000–57FFFF
2B8000–2BFFFF
SA88
0
1
0
1
1
0
0
0
64/32
580000–58FFFF
2C0000–2C7FFF
SA89
0
1
0
1
1
0
0
1
64/32
590000–59FFFF
2C8000–2CFFFF
SA90
0
1
0
1
1
0
1
0
64/32
5A0000–5AFFFF
2D0000–2D7FFF
SA91
0
1
0
1
1
0
1
1
64/32
5B0000–5BFFFF
2D8000–2DFFFF
SA92
0
1
0
1
1
1
0
0
64/32
5C0000–5CFFFF
2E0000–2E7FFF
SA93
0
1
0
1
1
1
0
1
64/32
5D0000–5DFFFF
2E8000–2EFFFF
SA94
0
1
0
1
1
1
1
0
64/32
5E0000–5EFFFF
2F0000–2F7FFF
September 9, 2003
Am29LV128MH/L
13
D A T A S H E E T
Table 2.
Sector
14
Sector Address Table (Continued)
A22–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA95
0
1
0
1
1
1
1
1
64/32
5F0000–5FFFFF
2F8000–2FFFFF
SA96
0
1
1
0
0
0
0
0
64/32
600000–60FFFF
300000–307FFF
SA97
0
1
1
0
0
0
0
1
64/32
610000–61FFFF
308000–30FFFF
SA98
0
1
1
0
0
0
1
0
64/32
620000–62FFFF
310000–317FFF
SA99
0
1
1
0
0
0
1
1
64/32
630000–63FFFF
318000–31FFFF
SA100
0
1
1
0
0
1
0
0
64/32
640000–64FFFF
320000–327FFF
SA101
0
1
1
0
0
1
0
1
64/32
650000–65FFFF
328000–32FFFF
SA102
0
1
1
0
0
1
1
0
64/32
660000–66FFFF
330000–337FFF
SA103
0
1
1
0
0
1
1
1
64/32
670000–67FFFF
338000–33FFFF
SA104
0
1
1
0
1
0
0
0
64/32
680000–68FFFF
340000–347FFF
SA105
0
1
1
0
1
0
0
1
64/32
690000–69FFFF
348000–34FFFF
SA106
0
1
1
0
1
0
1
0
64/32
6A0000–6AFFFF
350000–357FFF
SA107
0
1
1
0
1
0
1
1
64/32
6B0000–6BFFFF
358000–35FFFF
SA108
0
1
1
0
1
1
0
0
64/32
6C0000–6CFFFF
360000–367FFF
SA109
0
1
1
0
1
1
0
1
64/32
6D0000–6DFFFF
368000–36FFFF
SA110
0
1
1
0
1
1
1
0
64/32
6E0000–6EFFFF
370000–377FFF
SA111
0
1
1
0
1
1
1
1
64/32
6F0000–6FFFFF
378000–37FFFF
SA112
0
1
1
1
0
0
0
0
64/32
700000–70FFFF
380000–387FFF
SA113
0
1
1
1
0
0
0
1
64/32
710000–71FFFF
388000–38FFFF
SA114
0
1
1
1
0
0
1
0
64/32
720000–72FFFF
390000–397FFF
SA115
0
1
1
1
0
0
1
1
64/32
730000–73FFFF
398000–39FFFF
SA116
0
1
1
1
0
1
0
0
64/32
740000–74FFFF
3A0000–3A7FFF
SA117
0
1
1
1
0
1
0
1
64/32
750000–75FFFF
3A8000–3AFFFF
SA118
0
1
1
1
0
1
1
0
64/32
760000–76FFFF
3B0000–3B7FFF
SA119
0
1
1
1
0
1
1
1
64/32
770000–77FFFF
3B8000–3BFFFF
SA120
0
1
1
1
1
0
0
0
64/32
780000–78FFFF
3C0000–3C7FFF
SA121
0
1
1
1
1
0
0
1
64/32
790000–79FFFF
3C8000–3CFFFF
SA122
0
1
1
1
1
0
1
0
64/32
7A0000–7AFFFF
3D0000–3D7FFF
SA123
0
1
1
1
1
0
1
1
64/32
7B0000–7BFFFF
3D8000–3DFFFF
SA124
0
1
1
1
1
1
0
0
64/32
7C0000–7CFFFF
3E0000–3E7FFF
SA125
0
1
1
1
1
1
0
1
64/32
7D0000–7DFFFF
3E8000–3EFFFF
SA126
0
1
1
1
1
1
1
0
64/32
7E0000–7EFFFF
3F0000–3F7FFF
SA127
0
1
1
1
1
1
1
1
64/32
7F0000–7FFFFF
3F8000–3FFFFF
SA128
1
0
0
0
0
0
0
0
64/32
800000–80FFFF
400000–407FFF
SA129
1
0
0
0
0
0
0
1
64/32
810000–81FFFF
408000–40FFFF
SA130
1
0
0
0
0
0
1
0
64/32
820000–82FFFF
410000–417FFF
SA131
1
0
0
0
0
0
1
1
64/32
830000–83FFFF
418000–41FFFF
SA132
1
0
0
0
0
1
0
0
64/32
840000–84FFFF
420000–427FFF
SA133
1
0
0
0
0
1
0
1
64/32
850000–85FFFF
428000–42FFFF
SA134
1
0
0
0
0
1
1
0
64/32
860000–86FFFF
430000–437FFF
SA135
1
0
0
0
0
1
1
1
64/32
870000–87FFFF
438000–43FFFF
SA136
1
0
0
0
1
0
0
0
64/32
880000–88FFFF
440000–447FFF
SA137
1
0
0
0
1
0
0
1
64/32
890000–89FFFF
448000–44FFFF
SA138
1
0
0
0
1
0
1
0
64/32
8A0000–8AFFFF
450000–457FFF
SA139
1
0
0
0
1
0
1
1
64/32
8B0000–8BFFFF
458000–45FFFF
SA140
1
0
0
0
1
1
0
0
64/32
8C0000–8CFFFF
460000–467FFF
SA141
1
0
0
0
1
1
0
1
64/32
8D0000–8DFFFF
468000–46FFFF
SA142
1
0
0
0
1
1
1
0
64/32
8E0000–8EFFFF
470000–477FFF
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Table 2.
Sector
Sector Address Table (Continued)
A22–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA143
1
0
0
0
1
1
1
1
64/32
8F0000–8FFFFF
478000–47FFFF
SA144
1
0
0
1
0
0
0
0
64/32
900000–90FFFF
480000–487FFF
SA145
1
0
0
1
0
0
0
1
64/32
910000–91FFFF
488000–48FFFF
SA146
1
0
0
1
0
0
1
0
64/32
920000–92FFFF
490000–497FFF
SA147
1
0
0
1
0
0
1
1
64/32
930000–93FFFF
498000–49FFFF
SA148
1
0
0
1
0
1
0
0
64/32
940000–94FFFF
4A0000–4A7FFF
SA149
1
0
0
1
0
1
0
1
64/32
950000–95FFFF
4A8000–4AFFFF
SA150
1
0
0
1
0
1
1
0
64/32
960000–96FFFF
4B0000–4B7FFF
SA151
1
0
0
1
0
1
1
1
64/32
970000–97FFFF
4B8000–4BFFFF
SA152
1
0
0
1
1
0
0
0
64/32
980000–98FFFF
4C0000–4C7FFF
SA153
1
0
0
1
1
0
0
1
64/32
990000–99FFFF
4C8000–4CFFFF
SA154
1
0
0
1
1
0
1
0
64/32
9A0000–9AFFFF
4D0000–4D7FFF
SA155
1
0
0
1
1
0
1
1
64/32
9B0000–9BFFFF
4D8000–4DFFFF
SA156
1
0
0
1
1
1
0
0
64/32
9C0000–9CFFFF
4E0000–4E7FFF
SA157
1
0
0
1
1
1
0
1
64/32
9D0000–9DFFFF
4E8000–4EFFFF
SA158
1
0
0
1
1
1
1
0
64/32
9E0000–9EFFFF
4F0000–4F7FFF
SA159
1
0
0
1
1
1
1
1
64/32
9F0000–9FFFFF
4F8000–4FFFFF
SA160
1
0
1
0
0
0
0
0
64/32
A00000–A0FFFF
500000–507FFF
SA161
1
0
1
0
0
0
0
1
64/32
A10000–A1FFFF
508000–50FFFF
SA162
1
0
1
0
0
0
1
0
64/32
A20000–A2FFFF
510000–517FFF
SA163
1
0
1
0
0
0
1
1
64/32
A30000–A3FFFF
518000–51FFFF
SA164
1
0
1
0
0
1
0
0
64/32
A40000–A4FFFF
520000–527FFF
SA165
1
0
1
0
0
1
0
1
64/32
A50000–A5FFFF
528000–52FFFF
SA166
1
0
1
0
0
1
1
0
64/32
A60000–A6FFFF
530000–537FFF
SA167
1
0
1
0
0
1
1
1
64/32
A70000–A7FFFF
538000–53FFFF
SA168
1
0
1
0
1
0
0
0
64/32
A80000–A8FFFF
540000–547FFF
SA169
1
0
1
0
1
0
0
1
64/32
A90000–A9FFFF
548000–54FFFF
SA170
1
0
1
0
1
0
1
0
64/32
AA0000–AAFFFF
550000–557FFF
SA171
1
0
1
0
1
0
1
1
64/32
AB0000–ABFFFF
558000–55FFFF
SA172
1
0
1
0
1
1
0
0
64/32
AC0000–ACFFFF
560000–567FFF
SA173
1
0
1
0
1
1
0
1
64/32
AD0000–ADFFFF
568000–56FFFF
SA174
1
0
1
0
1
1
1
0
64/32
AE0000–AEFFFF
570000–577FFF
SA175
1
0
1
0
1
1
1
1
64/32
AF0000–AFFFFF
578000–57FFFF
SA176
1
0
1
1
0
0
0
0
64/32
B00000–B0FFFF
580000–587FFF
SA177
1
0
1
1
0
0
0
1
64/32
B10000–B1FFFF
588000–58FFFF
SA178
1
0
1
1
0
0
1
0
64/32
B20000–B2FFFF
590000–597FFF
SA179
1
0
1
1
0
0
1
1
64/32
B30000–B3FFFF
598000–59FFFF
SA180
1
0
1
1
0
1
0
0
64/32
B40000–B4FFFF
5A0000–5A7FFF
SA181
1
0
1
1
0
1
0
1
64/32
B50000–B5FFFF
5A8000–5AFFFF
SA182
1
0
1
1
0
1
1
0
64/32
B60000–B6FFFF
5B0000–5B7FFF
SA183
1
0
1
1
0
1
1
1
64/32
B70000–B7FFFF
5B8000–5BFFFF
SA184
1
0
1
1
1
0
0
0
64/32
B80000–B8FFFF
5C0000–5C7FFF
SA185
1
0
1
1
1
0
0
1
64/32
B90000–B9FFFF
5C8000–5CFFFF
SA186
1
0
1
1
1
0
1
0
64/32
BA0000–BAFFFF
5D0000–5D7FFF
SA187
1
0
1
1
1
0
1
1
64/32
BB0000–BBFFFF
5D8000–5DFFFF
SA188
1
0
1
1
1
1
0
0
64/32
BC0000–BCFFFF
5E0000–5E7FFF
SA189
1
0
1
1
1
1
0
1
64/32
BD0000–BDFFFF
5E8000–5EFFFF
SA190
1
0
1
1
1
1
1
0
64/32
BE0000–BEFFFF
5F0000–5F7FFF
September 9, 2003
Am29LV128MH/L
15
D A T A S H E E T
Table 2.
Sector
16
Sector Address Table (Continued)
A22–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA191
1
0
1
1
1
1
1
1
64/32
BF0000–BFFFFF
5F8000–5FFFFF
SA192
1
1
0
0
0
0
0
0
64/32
C00000–C0FFFF
600000–607FFF
SA193
1
1
0
0
0
0
0
1
64/32
C10000–C1FFFF
608000–60FFFF
SA194
1
1
0
0
0
0
1
0
64/32
C20000–C2FFFF
610000–617FFF
SA195
1
1
0
0
0
0
1
1
64/32
C30000–C3FFFF
618000–61FFFF
SA196
1
1
0
0
0
1
0
0
64/32
C40000–C4FFFF
620000–627FFF
SA197
1
1
0
0
0
1
0
1
64/32
C50000–C5FFFF
628000–62FFFF
SA198
1
1
0
0
0
1
1
0
64/32
C60000–C6FFFF
630000–637FFF
SA199
1
1
0
0
0
1
1
1
64/32
C70000–C7FFFF
638000–63FFFF
SA200
1
1
0
0
1
0
0
0
64/32
C80000–C8FFFF
640000–647FFF
SA201
1
1
0
0
1
0
0
1
64/32
C90000–C9FFFF
648000–64FFFF
SA202
1
1
0
0
1
0
1
0
64/32
CA0000–CAFFFF
650000–657FFF
SA203
1
1
0
0
1
0
1
1
64/32
CB0000–CBFFFF
658000–65FFFF
SA204
1
1
0
0
1
1
0
0
64/32
CC0000–CCFFFF
660000–667FFF
SA205
1
1
0
0
1
1
0
1
64/32
CD0000–CDFFFF
668000–66FFFF
SA206
1
1
0
0
1
1
1
0
64/32
CE0000–CEFFFF
670000–677FFF
SA207
1
1
0
0
1
1
1
1
64/32
CF0000–CFFFFF
678000–67FFFF
SA208
1
1
0
1
0
0
0
0
64/32
D00000–D0FFFF
680000–687FFF
SA209
1
1
0
1
0
0
0
1
64/32
D10000–D1FFFF
688000–68FFFF
SA210
1
1
0
1
0
0
1
0
64/32
D20000–D2FFFF
690000–697FFF
SA211
1
1
0
1
0
0
1
1
64/32
D30000–D3FFFF
698000–69FFFF
SA212
1
1
0
1
0
1
0
0
64/32
D40000–D4FFFF
6A0000–6A7FFF
SA213
1
1
0
1
0
1
0
1
64/32
D50000–D5FFFF
6A8000–6AFFFF
SA214
1
1
0
1
0
1
1
0
64/32
D60000–D6FFFF
6B0000–6B7FFF
SA215
1
1
0
1
0
1
1
1
64/32
D70000–D7FFFF
6B8000–6BFFFF
SA216
1
1
0
1
1
0
0
0
64/32
D80000–D8FFFF
6C0000–6C7FFF
SA217
1
1
0
1
1
0
0
1
64/32
D90000–D9FFFF
6C8000–6CFFFF
SA218
1
1
0
1
1
0
1
0
64/32
DA0000–DAFFFF
6D0000–6D7FFF
SA219
1
1
0
1
1
0
1
1
64/32
DB0000–DBFFFF
6D8000–6DFFFF
SA220
1
1
0
1
1
1
0
0
64/32
DC0000–DCFFFF
6E0000–6E7FFF
SA221
1
1
0
1
1
1
0
1
64/32
DD0000–DDFFFF
6E8000–6EFFFF
SA222
1
1
0
1
1
1
1
0
64/32
DE0000–DEFFFF
6F0000–6F7FFF
SA223
1
1
0
1
1
1
1
1
64/32
DF0000–DFFFFF
6F8000–6FFFFF
SA224
1
1
1
0
0
0
0
0
64/32
E00000–E0FFFF
700000–707FFF
SA225
1
1
1
0
0
0
0
1
64/32
E10000–E1FFFF
708000–70FFFF
SA226
1
1
1
0
0
0
1
0
64/32
E20000–E2FFFF
710000–717FFF
SA227
1
1
1
0
0
0
1
1
64/32
E30000–E3FFFF
718000–71FFFF
SA228
1
1
1
0
0
1
0
0
64/32
E40000–E4FFFF
720000–727FFF
SA229
1
1
1
0
0
1
0
1
64/32
E50000–E5FFFF
728000–72FFFF
SA230
1
1
1
0
0
1
1
0
64/32
E60000–E6FFFF
730000–737FFF
SA231
1
1
1
0
0
1
1
1
64/32
E70000–E7FFFF
738000–73FFFF
SA232
1
1
1
0
1
0
0
0
64/32
E80000–E8FFFF
740000–747FFF
SA233
1
1
1
0
1
0
0
1
64/32
E90000–E9FFFF
748000–74FFFF
SA234
1
1
1
0
1
0
1
0
64/32
EA0000–EAFFFF
750000–757FFF
SA235
1
1
1
0
1
0
1
1
64/32
EB0000–EBFFFF
758000–75FFFF
SA236
1
1
1
0
1
1
0
0
64/32
EC0000–ECFFFF
760000–767FFF
SA237
1
1
1
0
1
1
0
1
64/32
ED0000–EDFFFF
768000–76FFFF
SA238
1
1
1
0
1
1
1
0
64/32
EE0000–EEFFFF
770000–777FFF
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Table 2.
Sector
Sector Address Table (Continued)
A22–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA239
1
1
1
0
1
1
1
1
64/32
EF0000–EFFFFF
778000–77FFFF
SA240
1
1
1
1
0
0
0
0
64/32
F00000–F0FFFF
780000–787FFF
SA241
1
1
1
1
0
0
0
1
64/32
F10000–F1FFFF
788000–78FFFF
SA242
1
1
1
1
0
0
1
0
64/32
F20000–F2FFFF
790000–797FFF
SA243
1
1
1
1
0
0
1
1
64/32
F30000–F3FFFF
798000–79FFFF
SA244
1
1
1
1
0
1
0
0
64/32
F40000–F4FFFF
7A0000–7A7FFF
SA245
1
1
1
1
0
1
0
1
64/32
F50000–F5FFFF
7A8000–7AFFFF
SA246
1
1
1
1
0
1
1
0
64/32
F60000–F6FFFF
7B0000–7B7FFF
SA247
1
1
1
1
0
1
1
1
64/32
F70000–F7FFFF
7B8000–7BFFFF
SA248
1
1
1
1
1
0
0
0
64/32
F80000–F8FFFF
7C0000–7C7FFF
SA249
1
1
1
1
1
0
0
1
64/32
F90000–F9FFFF
7C8000–7CFFFF
SA250
1
1
1
1
1
0
1
0
64/32
FA0000–FAFFFF
7D0000–7D7FFF
SA251
1
1
1
1
1
0
1
1
64/32
FB0000–FBFFFF
7D8000–7DFFFF
SA252
1
1
1
1
1
1
0
0
64/32
FC0000–FCFFFF
7E0000–7E7FFF
SA253
1
1
1
1
1
1
0
1
64/32
FD0000–FDFFFF
7E8000–7EFFFF
SA254
1
1
1
1
1
1
1
0
64/32
FE0000–FEFFFF
7F0000–7F7FFF
SA255
1
1
1
1
1
1
1
1
64/32
FF0000–FFFFFF
7F8000–7FFFFF
September 9, 2003
Am29LV128MH/L
17
D A T A S H E E T
Autoselect Mode
In addition, when verifying sector protection, the sector
address must appear on the appropriate highest order
address bits (see Table 2). Table 3 shows the remaining address bits that are don’t care. When all necessary bits have been set as required, the programming
equipment may then read the corresponding identifier
code on DQ7–DQ0.
The autoselect mode provides manufacturer and device identification, and sector group protection verification, through identifier codes output on DQ7–DQ0.
This mode is primarily intended for programming
equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the autoselect codes can also be
accessed in-system through the command register.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in Tables 10 and 11. This
method does not require VID. Refer to the Autoselect
Command Sequence section for more information.
When using programming equipment, the autoselect
mode requires VID on address pin A9. Address pins
A6, A3, A2, A1, and A0 must be as shown in Table 3.
Table 3.
CE#
Manufacturer ID: AMD
L
Device ID
Description
OE# WE#
L
H
Autoselect Codes, (High Voltage Method)
A22 A14
to
to
A15 A10
X
X
A8
to
A7
A6
A5
to
A4
A3
to
A2
A1
A0
VID
X
L
X
L
L
L
00
X
01h
L
L
H
22
X
7Eh
H
H
L
22
X
12h
H
H
H
22
X
00h
Cycle 1
Cycle 2
L
L
H
X
X
DQ8 to DQ15
A9
VID
X
L
X
Cycle 3
BYTE# BYTE#
= VIH
= VIL
DQ7 to DQ0
Sector Group
Protection Verification
L
L
H
SA
X
VID
X
L
X
L
H
L
X
X
01h (protected),
00h (unprotected)
SecSi Sector Indicator
Bit (DQ7), WP#
protects highest
address sector
L
L
H
X
X
VID
X
L
X
L
H
H
X
X
98h (factory locked),
18h (not factory locked)
SecSi Sector Indicator
Bit (DQ7), WP#
protects lowest
address sector
L
L
H
X
X
VID
X
L
X
L
H
H
X
X
88h (factory locked),
08h (not factory locked)
Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.
18
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Sector Group Protection and Unprotection
The hardware sector group protection feature disables
both program and erase operations in any sector
group. The hardware sector group unprotection feature re-enables both program and erase operations in
previously protected sector groups. Sector group protection/unprotection can be implemented via two
methods.
Sector group protection/unprotection requires VID on
the RESET# pin only, and can be implemented either
in-system or via programming equipment. Figure 2
shows the algorithms and Figure 25 shows the timing
diagram. This method uses standard microprocessor
bus cycle timing. For sector group unprotect, all unprotected sector group must first be protected prior to the
first sector group unprotect write cycle.
The device is shipped with all sector groups unprotected. AMD offers the option of programming and protecting sector groups at its factory prior to shipping the
device through AMD’s ExpressFlash™ Service. Contact an AMD representative for details.
It is possible to determine whether a sector group is
protected or unprotected. See the Autoselect Mode
section for details.
Table 4.
Sector Group Protection/Unprotection
Address Table
Sector Group
SA0
A22–A15
00000000
SA1
00000001
SA2
00000010
SA3
00000011
SA4–SA7
000001xx
SA8–SA11
000010xx
SA12–SA15
000011xx
SA16–SA19
000100xx
SA20–SA23
000101xx
SA24–SA27
000110xx
SA28–SA31
000111xx
SA32–SA35
001000xx
SA36–SA39
001001xx
SA40–SA43
001010xx
SA44–SA47
001011xx
SA48–SA51
001100xx
SA52–SA55
001101xx
SA56–SA59
001110xx
SA60–SA63
001111xx
SA64–SA67
010000xx
SA68–SA71
010001xx
SA72–SA75
010010xx
SA76–SA79
010011xx
SA80–SA83
010100xx
September 9, 2003
Am29LV128MH/L
Sector Group
A22–A15
SA84–SA87
010101xx
SA88–SA91
010110xx
SA92–SA95
010111xx
SA96–SA99
011000xx
SA100–SA103
011001xx
SA104–SA107
011010xx
SA108–SA111
011011xx
SA112–SA115
011100xx
SA116–SA119
011101xx
SA120–SA123
011110xx
SA124–SA127
011111xx
SA128–SA131
100000xx
SA132–SA135
100001xx
SA136–SA139
100010xx
SA140–SA143
100011xx
SA144–SA147
100100xx
SA148–SA151
100101xx
SA152–SA155
100110xx
SA156–SA159
100111xx
SA160–SA163
101000xx
SA164–SA167
101001xx
SA168–SA171
101010xx
SA172–SA175
101011xx
SA176–SA179
101100xx
SA180–SA183
101101xx
SA184–SA187
101110xx
SA188–SA191
101111xx
SA192–SA195
110000xx
SA196–SA199
110001xx
SA200–SA203
110010xx
SA204–SA207
110011xx
SA208–SA211
110100xx
SA212–SA215
110101xx
SA216–SA219
110110xx
SA220–SA223
110111xx
SA224–SA227
111000xx
SA228–SA231
111001xx
SA232–SA235
111010xx
SA236–SA239
111011xx
SA240–SA243
111100xx
SA244–SA247
111101xx
SA248–SA251
111110xx
SA252
11111100
SA253
11111101
SA254
11111110
SA255
11111111
19
D A T A S H E E T
Write Protect (WP#)
The Write Protect function provides a hardware
method of protecting the first or last sector group without using VID. Write Protect is one of two functions provided by the WP#/ACC input.
shows the algorithm, and Figure 24 shows the timing
diagrams, for this feature.
START
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the first
or last sector group independently of whether those
sector groups were protected or unprotected using the
method described in “Sector Group Protection and
Unprotection”. Note that if WP#/ACC is at VIL when the
device is in the standby mode, the maximum input
load current is increased. See the table in “DC Characteristics”.
RESET# = VID
(Note 1)
Perform Erase or
Program Operations
If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the first or last sector was previously set to be protected or unprotected using the
method described in “Sector Group Protection and
Unprotection”. Note that WP# has an internal pullup;
when unconnected, WP# is at VIH.
RESET# = VIH
Temporary Sector Group
Unprotect Completed
(Note 2)
Temporary Sector Group Unprotect
This feature allows temporary unprotection of previously protected sector groups to change data in-system. The Sector Group Unprotect mode is activated by
setting the RESET# pin to VID. During this mode, formerly protected sector groups can be programmed or
erased by selecting the sector group addresses. Once
VID is removed from the RESET# pin, all the previously
protected sector groups are protected again. Figure 1
20
Notes:
1. All protected sector groups unprotected (If WP# = VIL,
the first or last sector will remain protected).
2. All previously protected sector groups are protected
once again.
Am29LV128MH/L
Figure 1. Temporary Sector Group
Unprotect Operation
September 9, 2003
D A T A S H E E T
START
START
Protect all sectors:
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector
unprotect address
PLSCNT = 1
RESET# = VID
Wait 1 µs
Temporary Sector
Unprotect Mode
No
PLSCNT = 1
RESET# = VID
Wait 1 µs
No
First Write
Cycle = 60h?
First Write
Cycle = 60h?
Yes
Yes
Set up sector
address
No
All sectors
protected?
Sector Protect:
Write 60h to sector
address with
A6 = 0, A1 = 1,
A0 = 0
Yes
Set up first sector
address
Sector Unprotect:
Write 60h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
Wait 150 µs
Increment
PLSCNT
Temporary Sector
Unprotect Mode
Verify Sector
Protect: Write 40h
to sector address
with A6 = 0,
A1 = 1, A0 = 0
Reset
PLSCNT = 1
Read from
sector address
with A6 = 0,
A1 = 1, A0 = 0
Wait 15 ms
Verify Sector
Unprotect: Write
40h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
Increment
PLSCNT
No
No
PLSCNT
= 25?
Yes
Yes
No
Yes
Device failed
Protect another
sector?
PLSCNT
= 1000?
No
Yes
Remove VID
from RESET#
Device failed
Write reset
command
Sector Group
Protect
Algorithm
Read from
sector address
with A6 = 1,
A1 = 1, A0 = 0
Data = 01h?
Set up
next sector
address
No
Data = 00h?
Yes
Last sector
verified?
No
Yes
Sector Protect
complete
Sector Group
Unprotect
Algorithm
Remove VID
from RESET#
Write reset
command
Sector Unprotect
complete
Figure 2.
September 9, 2003
In-System Sector Group Protect/Unprotect Algorithms
Am29LV128MH/L
21
D A T A S H E E T
SecSi (Secured Silicon) Sector Flash
Memory Region
Customer Lockable: SecSi Sector NOT
Programmed or Protected At the Factory
The SecSi (Secured Silicon) Sector feature provides a
Flash memory region that enables permanent part
identification through an Electronic Serial Number
(ESN). The SecSi Sector is 256 bytes in length, and
uses a SecSi Sector Indicator Bit (DQ7) to indicate
whether or not the SecSi Sector is locked when
shipped from the factory. This bit is permanently set at
the factory and cannot be changed, which prevents
cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field.
Unless otherwise specified, the device is shipped such
that the customer may program and protect the
256-byte SecSi sector.
AMD offers the device with the SecSi Sector either
customer lockable (standard shipping option) or factory locked (contact an AMD sales representative for
ordering information). The customer-lockable version
is shipped with the SecSi Sector unprotected, allowing
customers to program the sector after receiving the
device. The customer-lockable version also has the
SecSi Sector Indicator Bit permanently set to a “0.”
The factory-locked version is always protected when
shipped from the factory, and has the SecSi (Secured
Silicon) Sector Indicator Bit permanently set to a “1.”
Thus, the SecSi Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory locked. Note that the ACC
function and unlock bypass modes are not available
when the SecSi Sector is enabled.
The SecSi sector address space in this device is allocated as follows:
Table 5.
SecSi Sector
Address Range
000000h–000007h
000008h–00007Fh
SecSi Sector Contents
Customer
Lockable
Determined by
customer
ESN Factory
Locked
ExpressFlash
Factory Locked
ESN
ESN or
determined by
customer
Unavailable
Determined by
customer
The system accesses the SecSi Sector through a
command sequence (see “Enter SecSi Sector/Exit
SecSi Sector Command Sequence”). After the system
has written the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by the first sector (SA0).
This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or
until power is removed from the device. On power-up,
or following a hardware reset, the device reverts to
sending commands to sector SA0.
22
The system may program the SecSi Sector using the
write-buffer, accelerated and/or unlock bypass methods, in addition to the standard programming command sequence. See Command Definitions.
Programming and protecting the SecSi Sector must be
used with caution since, once protected, there is no
procedure available for unprotecting the SecSi Sector
area and none of the bits in the SecSi Sector memory
space can be modified in any way.
The SecSi Sector area can be protected using one of
the following procedures:
■ Write the three-cycle Enter SecSi Sector Region
command sequence, and then follow the in-system
sector protect algorithm as shown in Figure 2, except that RESET# may be at either VIH or VID. This
allows in-system protection of the SecSi Sector
without raising any device pin to a high voltage.
Note that this method is only applicable to the SecSi
Sector.
■ To verify the protect/unprotect status of the SecSi
Sector, follow the algorithm shown in Figure 3.
Once the SecSi Sector is programmed, locked and
verified, the system must write the Exit SecSi Sector
Region command sequence to return to reading and
writing within the remainder of the array.
Factory Locked: SecSi Sector Programmed and
Protected At the Factory
In devices with an ESN, the SecSi Sector is protected
when the device is shipped from the factory. The SecSi
Sector cannot be modified in any way. An ESN Factory
Locked device has an 16-byte random ESN at addresses 000000h–000007h. Please contact your local
AMD sales representative for details on ordering ESN
Factory Locked devices.
Customers may opt to have their code programmed by
AMD through the AMD ExpressFlash service (Express
Flash Factory Locked). The devices are then shipped
from AMD’s factory with the SecSi Sector permanently
locked. Contact an AMD representative for details on
using AMD’s ExpressFlash service.
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
caused by spurious system level signals during VCC
power-up and power-down transitions, or from system
noise.
START
RESET# =
VIH or VID
Wait 1 µs
Write 60h to
any address
Write 40h to SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
If data = 00h,
SecSi Sector is
unprotected.
If data = 01h,
SecSi Sector is
protected.
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC
power-up and power-down. The command register
and all internal program/erase circuits are disabled,
and the device resets to the read mode. Subsequent
writes are ignored until VCC is greater than VLKO. The
system must provide the proper signals to the control
pins to prevent unintentional writes when V CC is
greater than VLKO.
Remove VIH or VID
from RESET#
Write reset
command
Write Pulse “Glitch” Protection
Read from SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
Figure 3.
SecSi Sector
Protect Verify
complete
Noise pulses of less than 5 ns (typical) on OE#, CE#
or WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# =
VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,
CE# and WE# must be a logical zero while OE# is a
logical one.
SecSi Sector Protect Verify
Hardware Data Protection
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to Tables 10 and 11
for command definitions). In addition, the following
hardware data protection measures prevent accidental
erasure or programming, which might otherwise be
Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = V IH during power up,
the device does not accept commands on the rising
edge of WE#. The internal state machine is automatically reset to the read mode on power-up.
COMMON FLASH MEMORY INTERFACE (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation
handshake, which allows specific vendor-specified
software algorithms to be used for entire families of
devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and
backward-compatible for the specified flash device
families. Flash vendors can standardize their existing
interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address
55h, any time the device is ready to read array data.
The system can read CFI information at the addresses
given in Tables 6–9. To terminate reading CFI data,
the system must write the reset command.
September 9, 2003
The system can also write the CFI query command
when the device is in the autoselect mode. The device
enters the CFI query mode, and the system can read
CFI data at the addresses given in Tables 6–9. The
system must write the reset command to return the
device to reading array data.
For further information, please refer to the CFI Specification and CFI Publication 100, available via the World
Wide Web at http://www.amd.com/flash/cfi. Alternatively, contact an AMD representative for copies of
these documents.
Am29LV128MH/L
23
D A T A S H E E T
Table 6.
CFI Query Identification String
Addresses (x16)
Data
Description
10h
11h
12h
0051h
0052h
0059h
Query Unique ASCII string “QRY”
13h
14h
0002h
0000h
Primary OEM Command Set
15h
16h
0040h
0000h
Address for Primary Extended Table
17h
18h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
19h
1Ah
0000h
0000h
Address for Alternate OEM Extended Table (00h = none exists)
Table 7.
System Interface String
Addresses (x16)
Data
1Bh
0027h
VCC Min. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Ch
0036h
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Dh
0000h
VPP Min. voltage (00h = no VPP pin present)
1Eh
0000h
VPP Max. voltage (00h = no VPP pin present)
1Fh
0007h
Typical timeout per single byte/word write 2N µs
20h
0007h
Typical timeout for Min. size buffer write 2N µs (00h = not supported)
21h
000Ah
Typical timeout per individual block erase 2N ms
22h
0000h
Typical timeout for full chip erase 2N ms (00h = not supported)
23h
0001h
Max. timeout for byte/word write 2N times typical
24h
0005h
Max. timeout for buffer write 2N times typical
25h
0004h
Max. timeout per individual block erase 2N times typical
26h
0000h
Max. timeout for full chip erase 2N times typical (00h = not supported)
24
Description
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Table 8.
Device Geometry Definition
Addresses (x16)
Data
27h
0018h
Device Size = 2N byte
28h
29h
0002h
0000h
Flash Device Interface description (refer to CFI publication 100)
2Ah
2Bh
0005h
0000h
Max. number of byte in multi-byte write = 2N
(00h = not supported)
2Ch
0001h
Number of Erase Block Regions within device (01h = uniform device, 02h = boot
device)
2Dh
2Eh
2Fh
30h
00FFh
0000h
0000h
0001h
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
31h
32h
33h
34h
0000h
0000h
0000h
0000h
Erase Block Region 2 Information (refer to CFI publication 100)
35h
36h
37h
38h
0000h
0000h
0000h
0000h
Erase Block Region 3 Information (refer to CFI publication 100)
39h
3Ah
3Bh
3Ch
0000h
0000h
0000h
0000h
Erase Block Region 4 Information (refer to CFI publication 100)
September 9, 2003
Description
Am29LV128MH/L
25
D A T A S H E E T
Table 9.
Primary Vendor-Specific Extended Query
Addresses (x16)
Data
Description
40h
41h
42h
0050h
0052h
0049h
Query-unique ASCII string “PRI”
43h
0031h
Major version number, ASCII
44h
0033h
Minor version number, ASCII
45h
0008h
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Process Technology (Bits 7-2) 0010b = 0.23 µm MirrorBit
46h
0002h
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
47h
0001h
Sector Protect
0 = Not Supported, X = Number of sectors in per group
48h
0001h
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
49h
0004h
Sector Protect/Unprotect scheme
04 = 29LV800 mode
4Ah
0000h
Simultaneous Operation
00 = Not Supported, X = Number of Sectors in Bank
4Bh
0000h
Burst Mode Type
00 = Not Supported, 01 = Supported
4Ch
0001h
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
4Dh
00B5h
4Eh
00C5h
4Fh
0004h/
0005h
50h
0001h
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
Top/Bottom Boot Sector Flag
26
00h = Uniform Device without WP# protect, 02h = Bottom Boot Device, 03h = Top
Boot Device, 04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top
WP# protect
Program Suspend
00h = Not Supported, 01h = Supported
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
COMMAND DEFINITIONS
Writing specific address and data commands or sequences into the command register initiates device operations. Tables 10 and 11 defines the valid register
command sequences. Writing incorrect address and
data values or writing them in the improper sequence
may place the device in an unknown state. A reset
command is then required to return the device to reading array data.
All addresses are latched on the falling edge of WE#
or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the AC Characteristics section for timing
diagrams.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is ready to read array data
after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the erase-suspend-read mode, after
which the system can read data from any
non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the
system may once again read array data with the same
exception. See the Erase Suspend/Erase Resume
Commands section for more information.
The system must issue the reset command to return
the device to the read (or erase-suspend-read) mode if
DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See
the next section, Reset Command, for more information.
See also Requirements for Reading Array Data in the
Device Bus Operations section for more information.
The Read-Only Operations table provides the read parameters, and Figure 14 shows the timing diagram.
Reset Command
Writing the reset command resets the device to the
read or erase-suspend-read mode. Address bits are
don’t cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence before
erasing begins. This resets the device to the read
mode. Once erasure begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the device to
September 9, 2003
the read mode. If the program command sequence is
written while the device is in the Erase Suspend mode,
writing the reset command returns the device to the
erase-suspend-read mode. Once programming begins, however, the device ignores reset commands
until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command
must be written to return to the read mode. If the device entered the autoselect mode while in the Erase
Suspend mode, writing the reset command returns the
device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation,
writing the reset command returns the device to the
read mode (or erase-suspend-read mode if the device
was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the
Write-to-Buffer-Abort Reset command sequence to
reset the device for the next operation.
Autoselect Command Sequence
The autoselect command sequence allows the host
system to access the manufacturer and device codes,
and determine whether or not a sector is protected.
Tables 10 and 11 show the address and data requirements. This method is an alternative to that shown in
Table 3, which is intended for PROM programmers
and requires VID on address pin A9. The autoselect
command sequence may be written to an address that
is either in the read or erase-suspend-read mode. The
autoselect command may not be written while the device is actively programming or erasing.
The autoselect command sequence is initiated by first
writing two unlock cycles. This is followed by a third
write cycle that contains the autoselect command. The
device then enters the autoselect mode. The system
may read at any address any number of times without
initiating another autoselect command sequence:
■ A read cycle at address XX00h returns the manufacturer code.
■ Three read cycles at addresses 01h, 0Eh, and 0Fh
return the device code.
■ A read cycle to an address containing a sector address (SA), and the address 02h on A7–A0 in word
mode returns 01h if the sector is protected, or 00h if
it is unprotected.
The system must write the reset command to return to
the read mode (or erase-suspend-read mode if the device was previously in Erase Suspend).
Am29LV128MH/L
27
D A T A S H E E T
Enter SecSi Sector/Exit SecSi Sector
Command Sequence
Unlock Bypass Command Sequence
The SecSi Sector region provides a secured data area
containing an 8-word/16-byte random Electronic Serial
Number (ESN). The system can access the SecSi
Sector region by issuing the three-cycle Enter SecSi
Sector command sequence. The device continues to
access the SecSi Sector region until the system issues the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command sequence
returns the device to normal operation. Tables 10 and
11 show the address and data requirements for both
command sequences. See also “SecSi (Secured Silicon) Sector Flash Memory Region” for further information. Note that the ACC function and unlock bypass
modes are not available when the SecSi Sector is enabled.
Word/Byte Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two
unlock write cycles, followed by the program set-up
command. The program address and data are written
next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further
controls or timings. The device automatically provides
internally generated program pulses and verifies the
programmed cell margin. Tables 10 and 11 show the
address and data requirements for the word program
command sequence.
When the Embedded Program algorithm is complete,
the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using
DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the program
operation. The program command sequence should
be reinitiated once the device has returned to the read
mode, to ensure data integrity. Note that the SecSi
Sector, autoselect, and CFI functions are unavailable
when a program operation is in progress.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed
from “0” back to a “1.” Attempting to do so may
cause the device to set DQ5 = 1, or cause the DQ7
and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the
data is still “0.” Only erase operations can convert a “0”
to a “1.”
28
The unlock bypass feature allows the system to program words to the device faster than using the standard program command sequence. The unlock bypass
command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device
then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is
required to program in this mode. The first cycle in this
sequence contains the unlock bypass program command, A0h; the second cycle contains the program
address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial
two unlock cycles required in the standard program
command sequence, resulting in faster total programming time. Tables 10 and 11 show the requirements
for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands
are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data
90h. The second cycle must contain the data 00h. The
device then returns to the read mode.
Write Buffer Programming
Write Buffer Programming allows the system write to a
maximum of 16 words/32 bytes in one programming
operation. This results in faster effective programming
time than the standard programming algorithms. The
Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed
by a third write cycle containing the Write Buffer Load
command written at the Sector Address in which programming will occur. The fourth cycle writes the sector
address and the number of word locations, minus one,
to be programmed. For example, if the system will program 6 unique address locations, then 05h should be
written to the device. This tells the device how many
write buffer addresses will be loaded with data and
therefore when to expect the Program Buffer to Flash
command. The number of locations to program cannot
exceed the size of the write buffer or the operation will
abort.
The fifth cycle writes the first address location and
data to be programmed. The write-buffer-page is selected by address bits A MAX–A 4 . All subsequent add r e s s / d a t a p a i r s m u s t fa l l w i t h i n t h e
selected-write-buffer-page. The system then writes the
remaining address/data pairs into the write buffer.
Write buffer locations may be loaded in any order.
The write-buffer-page address must be the same for
all address/data pairs loaded into the write buffer.
(This means Write Buffer Programming cannot be performed across multiple write-buffer pages. This also
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts
to load programming data outside of the selected
write-buffer page, the operation will abort.
■ Write an Address/Data pair to a different
write-buffer-page than the one selected by the
Starting Address during the write buffer data loading stage of the operation.
Note that if a Write Buffer address location is loaded
multiple times, the address/data pair counter will be
decremented for every data load operation. The host
s y s t e m m u s t t h e r e fo r e a c c o u n t fo r l o a d i n g a
write-buffer location more than once. The counter decrements for each data load operation, not for each
unique write-buffer-address location. Note also that if
an address location is loaded more than once into the
buffer, the final data loaded for that address will be
programmed.
■ Write data other than the Confirm Command after
the specified number of data load cycles.
Once the specified number of write buffer locations
have been loaded, the system must then write the Program Buffer to Flash command at the sector address.
Any other address and data combination aborts the
Write Buffer Programming operation. The device then
begins programming. Data polling should be used
while monitoring the last address location loaded into
the write buffer. DQ7, DQ6, DQ5, and DQ1 should be
monitored to determine the device status during Write
Buffer Programming.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed
from “0” back to a “1.” Attempting to do so may
cause the device to set DQ5 = 1, or cause the DQ7
and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the
data is still “0.” Only erase operations can convert a “0”
to a “1.”
The write-buffer programming operation can be suspended using the standard program suspend/resume
commands. Upon successful completion of the Write
Buffer Programming operation, the device is ready to
execute the next command.
The device offers accelerated program operations
through the WP#/ACC pin. When the system asserts
VHH on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then
write the two-cycle Unlock Bypass program command
sequence. The device uses the higher voltage on the
WP#/ACC pin to accelerate the operation. Note that
the WP#/ACC pin must not be at V HH for operations
other than accelerated programming, or device damage may result. WP# has an internal pullup; when unconnected, WP# is at VIH.
The Write Buffer Programming Sequence can be
aborted in the following ways:
■ Load a value that is greater than the page buffer
size during the Number of Locations to Program
step.
■ Write to an address in a sector different than the
one specified during the Write-Buffer-Load command.
September 9, 2003
The abort condition is indicated by DQ1 = 1, DQ7 =
DATA# (for the last address location loaded), DQ6 =
toggle, and DQ5=0. A Write-to-Buffer-Abort Reset
command sequence must be written to reset the device for the next operation. Note that the full 3-cycle
Write-to-Buffer-Abort Reset command sequence is required when using Write-Buffer-Programming features
in Unlock Bypass mode.
Accelerated Program
Figure 5 illustrates the algorithm for the program operation. Refer to the Erase and Program Operations
table in the AC Characteristics section for parameters,
and Figure 18 for timing diagrams.
Am29LV128MH/L
29
D A T A S H E E T
Write “Write to Buffer”
command and
Sector Address
Part of “Write to Buffer”
Command Sequence
Write number of addresses
to program minus 1(WC)
and Sector Address
Write first address/data
Yes
WC = 0 ?
No
Write to a different
sector address
Abort Write to
Buffer Operation?
Yes
Write to buffer ABORTED.
Must write “Write-to-buffer
Abort Reset” command
sequence to return
to read mode.
No
(Note 1)
Write next address/data pair
WC = WC - 1
Write program buffer to
flash sector address
Notes:
1.
Read DQ7 - DQ0 at
Last Loaded Address
No
2. DQ7 may change simultaneously with DQ5.
Therefore, DQ7 should be verified.
3. If this flowchart location was reached because
DQ5= “1”, then the device FAILED. If this flowchart
location was reached because DQ1= “1”, then the
Write to Buffer operation was ABORTED. In either
case, the proper reset command must be written
before the device can begin another operation. If
DQ1=1, write the
Write-Buffer-Programming-Abort-Reset
command. if DQ5=1, write the Reset command.
Yes
DQ7 = Data?
No
No
DQ1 = 1?
DQ5 = 1?
Yes
Yes
When Sector Address is specified, any address in
the selected sector is acceptable. However, when
loading Write-Buffer address locations with data, all
addresses must fall within the selected Write-Buffer
Page.
4.
See Tables 10 and 11 for command sequences
required for write buffer programming.
Read DQ7 - DQ0 with
address = Last Loaded
Address
(Note 2)
DQ7 = Data?
Yes
No
(Note 3)
FAIL or ABORT
Figure 4.
30
PASS
Write Buffer Programming Operation
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Program Suspend/Program Resume
Command Sequence
The Program Suspend command allows the system to
interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from
any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the program operation within 15
µs maximum (5 µs typical) and updates the status bits.
Addresses are not required when writing the Program
Suspend command.
START
Write Program
Command Sequence
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
Yes
Increment Address
No
Last Address?
Yes
Programming
Completed
Note: See Tables 10 and 11 for program command
sequence.
Figure 5.
Program Operation
No
After the programming operation has been suspended, the system can read array data from any
non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data
may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from
the SecSi Sector area (One-time Program area), then
user must use the proper command sequences to
enter and exit this region.
The system may also write the autoselect command
sequence when the device is in the Program Suspend
mode. The system can read as many autoselect codes
as required. When the device exits the autoselect
mode, the device reverts to the Program Suspend
mode, and is ready for another valid operation. See
Autoselect Command Sequence for more information.
After the Program Resume command is written, the
device reverts to programming. The system can determine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard program operation. See Write Operation Status for more
information.
The system must write the Program Resume command to exit the Program Suspend mode and continue
the programming operation. The address of the program-suspended sector is required when writing this
command. Further writes of the Resume command
are ignored. Another Program Suspend command can
be written after the device has resume programming.
September 9, 2003
Am29LV128MH/L
31
D A T A S H E E T
When the Embedded Erase algorithm is complete, the
device returns to the read mode and addresses are no
longer latched. The system can determine the status
of the erase operation by using DQ7, DQ6, or DQ2.
Refer to the Write Operation Status section for information on these status bits.
Program Operation
or Write-to-Buffer
Sequence in Progress
Write address/data
XXXh/B0h
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Wait 15 µs
Read data as
required
No
Autoselect and SecSi Sector
read operations are also allowed
Data cannot be read from erase- or
program-suspended sectors
Done
reading?
Yes
Write address/data
XXXh/30h
Program Suspend/Program Resume
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase. The system is not required to provide any controls or timings during these operations. Tables 10 and
11 show the address and data requirements for the
chip erase command sequence.
32
Figure 6 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters,
and Figure 20 section for timing diagrams.
Sector Erase Command Sequence
Write Program Resume
Command Sequence
Device reverts to
operation prior to
Program Suspend
Figure 6.
Any commands written during the chip erase operation
are ignored.However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be
reinitiated once the device has returned to reading
array data, to ensure data integrity. Note that the
SecSi Sector, autoselect, and CFI functions are unavailable when an program operation is in progress.
Sector erase is a six bus cycle operation. The sector
erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and
the sector erase command. Tables 9 & 10 shows the
address and data requirements for the sector erase
command sequence.
The device does not require the system to preprogram
prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for
an all zero data pattern prior to electrical erase. The
system is not required to provide any controls or timings during these operations.
After the command sequence is written, a sector erase
time-out of 50 µs occurs. During the time-out period,
additional sector addresses and sector erase commands may be written. Loading the sector erase buffer
may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time
between these additional cycles must be less than 50
µs, otherwise erasure may begin. Any sector erase address and command following the exceeded time-out
may or may not be accepted. It is recommended that
processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can
be re-enabled after the last Sector Erase command is
written. Any command other than Sector Erase or
Erase Suspend during the time-out period resets
the device to the read mode. The system must rewrite the command sequence and any additional addresses and commands. Note that the SecSi Sector,
autoselect, and CFI functions are unavailable when an
erase operation is in progress.
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3:
Sector Erase Timer.). The time-out begins from the rising edge of the final WE# pulse in the command
sequence.
Erase Suspend/Erase Resume
Commands
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses
are no longer latched. The system can determine the
status of the erase operation by reading DQ7, DQ6, or
DQ2 in the erasing sector. Refer to the Write Operation Status section for information on these status bits.
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read
data from, or program data to, any sector not selected
for erasure. This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The
Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program
algorithm.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands are ignored. However, note that a hardware
reset immediately terminates the erase operation. If
that occurs, the sector erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure data integrity.
When the Erase Suspend command is written during
the sector erase operation, the device requires a typical of 5 µs (maximum of 20 µs) to suspend the erase
operation. However, when the Erase Suspend command is written during the sector erase time-out, the
device immediately terminates the time-out period and
suspends the erase operation.
Figure 6 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters,
and Figure 20 section for timing diagrams.
After the erase operation has been suspended, the
device enters the erase-suspend-read mode. The system can read data from or program data to any sector
not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at
any address within erase-suspended sectors produces status information on DQ7–DQ0. The system
can use DQ7, or DQ6 and DQ2 together, to determine
if a sector is actively erasing or is erase-suspended.
Refer to the Write Operation Status section for information on these status bits.
START
Write Erase
Command Sequence
(Notes 1, 2)
Data Poll to Erasing
Bank from System
No
After an erase-suspended program operation is complete, the device returns to the erase-suspend-read
mode. The system can determine the status of the
program operation using the DQ7 or DQ6 status bits,
just as in the standard word program operation.
Refer to the Write Operation Status section for more
information.
Embedded
Erase
algorithm
in progress
In the erase-suspend-read mode, the system can also
issue the autoselect command sequence. Refer to the
Autoselect Mode and Autoselect Command Sequence
sections for details.
Data = FFh?
To resume the sector erase operation, the system
must write the Erase Resume command. The address
of the erase-suspended sector is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command
can be written after the chip has resumed erasing.
Yes
Erasure Completed
Figure 7.
Erase Operation
Notes:
1. See Tables 10 and 11 for erase command sequence.
2. See the section on DQ3 for information on the sector
erase timer.
September 9, 2003
Am29LV128MH/L
33
D A T A S H E E T
Command Definitions
Table 10.
Read (Note 6)
Autoselect (Note 8)
Reset (Note 7)
Bus Cycles (Notes 2–5)
Cycles
Command
Sequence
(Note 1)
Command Definitions (x16 Mode, BYTE# = VIH)
Addr
Data
1
RA
RD
First
Second
Third
Fourth
Addr
Data
Addr
Data
Addr
Fifth
Data
1
XXX
F0
Manufacturer ID
4
555
AA
2AA
55
555
90
X00
0001
Device ID (Note 9)
4
555
AA
2AA
55
555
90
X01
227E
SecSi™ Sector Factory Protect
(Note 10)
4
555
AA
2AA
55
555
90
X03
(Note 10)
Sector Group Protect Verify
(Note 12)
4
555
AA
2AA
55
555
90
(SA)X02
00/01
Sixth
Addr
Data
Addr
Data
X0E
2212
X0F
2200
PA
PD
WBL
PD
Enter SecSi Sector Region
3
555
AA
2AA
55
555
88
Exit SecSi Sector Region
4
555
AA
2AA
55
555
90
XXX
00
Program
4
555
AA
2AA
55
555
A0
PA
PD
Write to Buffer (Note 11)
3
555
AA
2AA
55
SA
25
SA
WC
Program Buffer to Flash
1
SA
29
Write to Buffer Abort Reset (Note 13)
3
555
AA
2AA
55
555
F0
Unlock Bypass
3
555
AA
2AA
55
555
20
Unlock Bypass Program (Note 14)
2
XXX
A0
PA
PD
Unlock Bypass Reset (Note 15)
2
XXX
90
XXX
00
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Program/Erase Suspend (Note 16)
1
SA
B0
Program/Erase Resume (Note 17)
1
SA
30
CFI Query (Note 18)
1
55
98
Legend:
X = Don’t care
RA = Read Address of the memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address. Addresses latch on the falling edge of the WE#
or CE# pulse, whichever happens later.
PD = Program Data for location PA. Data latches on the rising edge of
WE# or CE# pulse, whichever happens first.
Notes:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
SA = Sector Address of sector to be verified (in autoselect mode) or
erased. Address bits A22–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within the same write
buffer page as PA.
WC = Word Count. Number of write buffer locations to load minus 1.
lowest address sector, the data is 88h for factory locked and 08h
for not factor locked.
3. Except for the read cycle and the fourth cycle of the autoselect
command sequence, all bus cycles are write cycles.
4. Data bits DQ15–DQ8 are don’t care in command sequences,
except for RD, PD, and WC.
5. Unless otherwise noted, address bits A22–A11 are don’t cares.
6. No unlock or command cycles required when device is in read
mode.
7. The Reset command is required to return to the read mode (or to
the erase-suspend-read mode if previously in Erase Suspend)
when the device is in the autoselect mode, or if DQ5 goes high
while the device is providing status information.
8. The fourth cycle of the autoselect command sequence is a read
cycle. Data bits DQ15–DQ8 are don’t care. See the Autoselect
Command Sequence section for more information.
9. The device ID must be read in three cycles.
10. If WP# protects the highest address sector, the data is 98h for
factory locked and 18h for not factory locked. If WP# protects the
11. The total number of cycles in the command sequence is
determined by the number of words written to the write buffer. The
maximum number of cycles in the command sequence is 21.
12. The data is 00h for an unprotected sector and 01h for a protected
sector.
13. Command sequence resets device for next command after
aborted write-to-buffer operation.
14. The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
15. The Unlock Bypass Reset command is required to return to the
read mode when the device is in the unlock bypass mode.
16. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation.
17. The Erase Resume command is valid only during the Erase
Suspend mode.
18. Command is valid when device is ready to read array data or when
device is in autoselect mode.
34
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
Table 11.
Read (Note 6)
Autoselect (Note 8)
Reset (Note 7)
Bus Cycles (Notes 2–5)
Cycles
Command
Sequence
(Note 1)
Command Definitions (x8 Mode, BYTE# = VIL)
Addr
Data
1
RA
RD
First
Second
Third
Fourth
Addr
Data
Addr
Data
Addr
Fifth
Data
1
XXX
F0
Manufacturer ID
4
AAA
AA
555
55
AAA
90
X00
01
Device ID (Note 9)
4
AAA
AA
555
55
AAA
90
X02
7E
SecSi™ Sector Factory Protect
(Note 10)
4
AAA
AA
555
55
AAA
90
X06
(Note 10)
Sector Group Protect Verify
(Note 12)
4
AAA
AA
555
55
AAA
90
(SA)X04
00/01
Sixth
Addr
Data
Addr
Data
X1C
12
X1E
00
PA
PD
WBL
PD
Enter SecSi Sector Region
3
AAA
AA
555
55
AAA
88
Exit SecSi Sector Region
4
AAA
AA
555
55
AAA
90
XXX
00
Program
4
AAA
AA
555
55
AAA
A0
PA
PD
Write to Buffer (Note 11)
3
AAA
AA
555
55
SA
25
SA
BC
Program Buffer to Flash
1
SA
29
Write to Buffer Abort Reset (Note 13)
3
AAA
AA
555
55
AAA
F0
Unlock Bypass
3
AAA
AA
555
55
AAA
20
Unlock Bypass Program (Note 14)
2
XXX
A0
PA
PD
Unlock Bypass Reset (Note 15)
2
XXX
90
XXX
00
Chip Erase
6
AAA
AA
555
55
AAA
80
AAA
AA
555
55
AAA
10
Sector Erase
6
AAA
AA
555
55
AAA
80
AAA
AA
555
55
SA
30
Program/Erase Suspend (Note 16)
1
SA
B0
Program/Erase Resume (Note 17)
1
SA
30
CFI Query (Note 18)
1
AA
98
Legend:
X = Don’t care
RA = Read Address of the memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address. Addresses latch on the falling edge of the WE#
or CE# pulse, whichever happens later.
PD = Program Data for location PA. Data latches on the rising edge of
WE# or CE# pulse, whichever happens first.
Notes:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
SA = Sector Address of sector to be verified (in autoselect mode) or
erased. Address bits A22–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within the same write
buffer page as PA.
BC = Byte Count. Number of write buffer locations to load minus 1.
lowest address sector, the data is 88h for factory locked and 08h
for not factor locked.
3. Except for the read cycle and the fourth cycle of the autoselect
command sequence, all bus cycles are write cycles.
4. Data bits DQ15–DQ8 are don’t care in command sequences,
except for RD and PD.
5. Unless otherwise noted, address bits A22–A11 are don’t cares.
6. No unlock or command cycles required when device is in read
mode.
7. The Reset command is required to return to the read mode (or to
the erase-suspend-read mode if previously in Erase Suspend)
when the device is in the autoselect mode, or if DQ5 goes high
while the device is providing status information.
8. The fourth cycle of the autoselect command sequence is a read
cycle. Data bits DQ15–DQ8 are don’t care. See the Autoselect
Command Sequence section for more information.
9. The device ID must be read in three cycles.
10. If WP# protects the highest address sector, the data is 98h for
factory locked and 18h for not factory locked. If WP# protects the
11. The total number of cycles in the command sequence is
determined by the number of words written to the write buffer. The
maximum number of cycles in the command sequence is 37.
12. The data is 00h for an unprotected sector group and 01h for a
protected sector group.
13. Command sequence resets device for next command after
aborted write-to-buffer operation.
14. The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
15. The Unlock Bypass Reset command is required to return to the
read mode when the device is in the unlock bypass mode.
16. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation.
17. The Erase Resume command is valid only during the Erase
Suspend mode.
18. Command is valid when device is ready to read array data or when
device is in autoselect mode.
September 9, 2003
Am29LV128MH/L
35
D A T A S H E E T
WRITE OPERATION STATUS
The device provides several bits to determine the status of a
program or erase operation: DQ2, DQ3, DQ5, DQ6, and
DQ7. Table 12 and the following subsections describe the
function of these bits. DQ7 and DQ6 each offer a method for
determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to determine
whether an Embedded Program or Erase operation is
in progress or has been completed.
valid data, the data outputs on DQ0–DQ6 may be still
invalid. Valid data on DQ0–DQ7 will appear on successive read cycles.
Table 12 shows the outputs for Data# Polling on DQ7.
Figure 8 shows the Data# Polling algorithm. Figure 21
in the AC Characteristics section shows the Data#
Polling timing diagram.
DQ7: Data# Polling
START
The Data# Polling bit, DQ7, indicates to the host system
whether an Embedded Program or Erase algorithm is in
progress or completed, or whether the device is in Erase
Suspend. Data# Polling is valid after the rising edge of the
final WE# pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to
DQ7. This DQ7 status also applies to programming during
Erase Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to
DQ7. The system must provide the program address to
read valid status information on DQ7. If a program address
falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to the
read mode.
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
No
No
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status information on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the
device returns to the read mode. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected
sector, the status may not be valid.
Just prior to the completion of an Embedded Program
or Erase operation, DQ7 may change asynchronously
with DQ0–DQ6 while Output Enable (OE#) is asserted
low. That is, the device may change from providing
status information to valid data on DQ7. Depending on
when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has completed the program or erase operation and DQ7 has
36
Yes
DQ5 = 1?
Yes
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
Yes
No
FAIL
PASS
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is any sector address
within the sector being erased. During chip erase, a
valid address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
Am29LV128MH/L
Figure 8. Data# Polling Algorithm
September 9, 2003
D A T A S H E E T
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin
which indicates whether an Embedded Algorithm is in
progress or complete. The RY/BY# status is valid after
the rising edge of the final WE# pulse in the command
sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a
pull-up resistor to VCC.
If the output is low (Busy), the device is actively erasing or programming. (This includes programming in
the Erase Suspend mode.) If the output is high
(Ready), the device is in the read mode, the standby
mode, or in the erase-suspend-read mode. Table 12
shows the outputs for RY/BY#.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase
Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final
WE# pulse in the command sequence (prior to the
program or erase operation), and during the sector
erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause
DQ6 to toggle. The system may use either OE# or
CE# to control the read cycles. When the operation is
complete, DQ6 stops toggling.
September 9, 2003
After an erase command sequence is written, if all sectors
selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all
selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected.
The system can use DQ6 and DQ2 together to determine
whether a sector is actively erasing or is erase-suspended.
When the device is actively erasing (that is, the Embedded
Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling.
However, the system must also use DQ2 to determine
which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on
DQ7: Data# Polling).
If a program address falls within a protected sector,
DQ6 toggles for approximately 1 µs after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Program algorithm is complete.
Table 12 shows the outputs for Toggle Bit I on DQ6.
Figure 9 shows the toggle bit algorithm. Figure 22 in
the “AC Characteristics” section shows the toggle bit
timing diagrams. Figure 23 shows the differences between DQ2 and DQ6 in graphical form. See also the
subsection on DQ2: Toggle Bit II.
Am29LV128MH/L
37
D A T A S H E E T
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit
II is valid after the rising edge of the final WE# pulse in
the command sequence.
START
Read DQ7–DQ0
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish
whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the
device is actively erasing, or is in Erase Suspend, but
cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and
mode information. Refer to Table 12 to compare outputs for DQ2 and DQ6.
Read DQ7–DQ0
Toggle Bit
= Toggle?
No
Yes
No
Figure 9 shows the toggle bit algorithm in flowchart
form, and the section “DQ2: Toggle Bit II” explains the
algorithm. See also the RY/BY#: Ready/Busy# subsection. Figure 22 shows the toggle bit timing diagram.
Figure 23 shows the differences between DQ2 and
DQ6 in graphical form.
DQ5 = 1?
Yes
Read DQ7–DQ0
Twice
Toggle Bit
= Toggle?
Reading Toggle Bits DQ6/DQ2
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Note: The system should recheck the toggle bit even if
DQ5 = “1” because the toggle bit may stop toggling as DQ5
changes to “1.” See the subsections on DQ6 and DQ2 for
more information.
Figure 9.
Toggle Bit Algorithm
Refer to Figure 9 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically,
the system would note and store the value of the toggle bit after the first read. After the second read, the
system would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device
has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the device did not completed the operation successfully, and
the system must write the reset command to return to
reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor
the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform
38
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
other system tasks. In this case, the system must start
at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 9).
DQ5: Exceeded Timing Limits
DQ5 indic ates whether the program, erase, or
write-to-buffer time has exceeded a specified internal
pulse count limit. Under these conditions DQ5 produces a
“1,” indicating that the program or erase cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries
to program a “1” to a location that was previously programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the
device halts the operation, and when the timing limit
has been exceeded, DQ5 produces a “1.”
In all these cases, the system must write the reset
command to return the device to the reading the array
(or to erase-suspend-read if the device was previously
in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out
also applies after each additional sector erase com-
September 9, 2003
mand. When the time-out period is complete, DQ3
switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be
assumed to be less than 50 µs, the system need not
monitor DQ3. See also the Sector Erase Command
Sequence section.
After the sector erase command is written, the system
should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the
device will accept additional sector erase commands.
To ensure the command has been accepted, the system software should check the status of DQ3 prior to
and following each subsequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 12 shows the status of DQ3 relative to the other
status bits.
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation
was aborted. Under these conditions DQ1 produces a
“1”.
The
system
must
issue
the
Write-to-Buffer-Abort-Reset command sequence to return the device to reading array data. See Write Buffer
Programming section for more details.
Am29LV128MH/L
39
D A T A S H E E T
Table 12.
Standard
Mode
Program
Suspend
Mode
Erase
Suspend
Mode
Write-toBuffer
Status
Embedded Program Algorithm
Embedded Erase Algorithm
Program-Suspended
ProgramSector
Suspend
Non-Program
Read
Suspended Sector
Erase-Suspended
EraseSector
Suspend
Non-Erase Suspended
Read
Sector
Erase-Suspend-Program
(Embedded Program)
Busy (Note 3)
Abort (Note 4)
Write Operation Status
DQ7
(Note 2)
DQ7#
0
1
DQ6
Toggle
Toggle
No toggle
DQ5
(Note 1)
0
0
DQ3
N/A
1
DQ2
(Note 2)
No toggle
Toggle
DQ1
0
N/A
RY/BY#
0
0
Invalid (not allowed)
1
Data
1
0
N/A
Toggle
N/A
Data
1
1
DQ7#
Toggle
0
N/A
N/A
N/A
0
DQ7#
DQ7#
Toggle
Toggle
0
0
N/A
N/A
N/A
N/A
0
1
0
0
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the
maximum timing limits. Refer to the section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location.
4. DQ1 switches to ‘1’ when the device has aborted the write-to-buffer operation.
40
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature
with Power Applied. . . . . . . . . . . . . . –65°C to +125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . .–0.5 V to +4.0 V
20 ns
20 ns
+0.8 V
–0.5 V
–2.0 V
VIO . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +4.0 V
20 ns
A9, OE#, ACC, and RESET#
(Note 2) . . . . . . . . . . . . . . . . . . . .–0.5 V to +12.5 V
Figure 10. Maximum Negative
Overshoot Waveform
All other pins (Note 1) . . . . . . –0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V.
During voltage transitions, input or I/O pins may
overshoot V SS to –2.0 V for periods of up to 20 ns.
Maximum DC voltage on input or I/O pins is VCC +0.5 V.
See Figure 10. During voltage transitions, input or I/O
pins may overshoot to VCC +2.0 V for periods up to 20 ns.
See Figure 11.
2. Minimum DC input voltage on pins A9, OE#, ACC, and
RESET# is –0.5 V. During voltage transitions, A9, OE#,
ACC, and RESET# may overshoot V SS to –2.0 V for
periods of up to 20 ns. See Figure 10. Maximum DC
input voltage on pin A9, OE#, ACC, and RESET# is
+12.5 V which may overshoot to +14.0 V for periods up
to 20 ns.
20 ns
VCC
+2.0 V
VCC
+0.5 V
2.0 V
20 ns
20 ns
Figure 11. Maximum Positive
Overshoot Waveform
3. No more than one output may be shorted to ground at a
time. Duration of the short circuit should not be greater
than one second.
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device reliability.
OPERATING RANGES
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . . . . . . –40°C to +85°C
Supply Voltages
VCC (regulated voltage range) . . . . . . . . . . . . . . . . 3.0–3.6 V
VCC (full voltage range) . . . . . . . . . . . . . . . . . . . . . 2.7–3.6 V
VIO (Note 2) . . . . . . . . . . . . . . . . . . . . . . 1.65–3.6 V (Note 3)
Notes:
1. Operating ranges define those limits between which the
functionality of the device is guaranteed.
2. See Ordering Information section for valid VCC/VIO range
combinations. The I/Os will not operate at 3V when VIO =
1.8V.
3. 100R parts have a VIO range from 2.7–3.6 V.
September 9, 2003
Am29LV128MH/L
41
D A T A S H E E T
DC CHARACTERISTICS
CMOS Compatible
Parameter
Symbol
Parameter Description
(Notes)
Test Conditions
Min
ILI
Input Load Current (1)
VIN = VSS to VCC,
VCC = VCC max
ILIT
A9, ACC Input Load Current
VCC = VCC max; A9 = 12.5 V
ILO
Output Leakage Current
VOUT = VSS to VCC,
VCC = VCC max
ILR
Reset Leakage Current
VCC = VCC max; RESET# = 12.5 V
ICC1
VCC Active Read Current
(2, 3)
CE# = VIL, OE# = VIH,
ICC2
VCC Initial Page Read Current (2, 3) CE# = VIL, OE# = VIH
ICC3
VCC Intra-Page Read Current (2, 3)
CE# = VIL, OE# = VIH
ICC4
VCC Active Write Current (3, 4)
ICC5
Typ
Max
Unit
±1.0
µA
35
µA
±1.0
µA
35
µA
5 MHz
3
34
1 MHz
13
43
1 MHz
4
50
10 MHz
40
80
10 MHz
3
20
33 MHz
6
40
mA
CE# = VIL, OE# = VIH
50
60
mA
VCC Standby Current (3)
CE#, RESET# = VCC ± 0.3 V, WP# = VIH
1
5
µA
ICC6
VCC Reset Current (3)
RESET# = VSS ± 0.3 V, WP# = VIH
1
5
µA
ICC7
Automatic Sleep Mode (3, 5)
VIH = VCC ± 0.3 V; VIL = VSS ± 0.3 V,
WP# = VIH
1
5
µA
VIL1
Input Low Voltage 1(6, 7)
–0.5
0.8
V
VIH1
Input High Voltage 1 (6, 7)
1.9
VCC +
0.5
V
VIL2
Input Low Voltage 2 (6, 8)
–0.5
0.3 x VIO
V
VIH2
Input High Voltage 2 (6, 8)
1.9
VIO + 0.5
V
VHH
Voltage for ACC Program
Acceleration
VCC = 2.7–3.6 V
11.5
12.5
V
VID
Voltage for Autoselect and
Temporary Sector Unprotect
VCC = 2.7–3.6 V
11.5
12.5
V
VOL
Output Low Voltage (10)
IOL = 4.0 mA, VCC = VCC min = VIO
0.15 x
VIO
V
VOH1
VOH2
VLKO
Output High Voltage
mA
mA
IOH = –2.0 mA, VCC = VCC min = VIO
0.85 VIO
V
IOH = –100 µA, VCC = VCC min = VIO
VIO–0.4
V
Low VCC Lock-Out Voltage (9)
2.3
Notes:
1. On the WP#/ACC pin only, the maximum input load current when
WP# = VIL is ± 5.0 µA.
2. The ICC current listed is typically less than 2 mA/MHz, with OE# at
VIH.
3. Maximum ICC specifications are tested with VCC = VCCmax.
4. ICC active while Embedded Erase or Embedded Program is in
progress.
2.5
V
5. Automatic sleep mode enables the low power mode when
addresses remain stable for tACC + 30 ns.
6. If VIO < VCC, maximum VIL for CE# and DQ I/Os is 0.3 VIO.
Maximum VIH for these connections is VIO + 0.3 V
7. VCC voltage requirements.
8. VIO voltage requirements.
9. Not 100% tested.
10. Includes RY/BY#
42
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
TEST CONDITIONS
Table 13.
3.3 V
Test Condition
2.7 kΩ
Device
Under
Test
CL
Test Specifications
6.2 kΩ
All Speeds
Output Load
1 TTL gate
Output Load Capacitance, CL
(including jig capacitance)
30
pF
Input Rise and Fall Times
5
ns
0.0–3.0
V
Input timing measurement
reference levels (See Note)
1.5
V
Output timing measurement
reference levels
0.5 VIO
V
Input Pulse Levels
Note: Diodes are IN3064 or equivalent
Figure 12.
Test Setup
Unit
Note: If VIO < VCC, the reference level is 0.5 VIO.
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
3.0 V
Input
Don’t Care, Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High Impedance State (High Z)
1.5 V
Measurement Level
0.5 VIO V
Output
0.0 V
Note: If VIO < VCC, the input measurement reference level is 0.5 VIO.
Figure 13.
September 9, 2003
Input Waveforms and Measurement Levels
Am29LV128MH/L
43
D A T A S H E E T
AC CHARACTERISTICS
Read-Only Operations
Parameter
JEDEC
Speed Options
Std. Description
93R
103,
103R
Min
90
100
110
120
ns
CE#, OE# = VIL
Max
90
100
110
120
ns
OE# = VIL
Max
90
100
110
120
ns
Max
25
30
30
40
30
40
ns
25
30
30
40
30
40
ns
Test Setup
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable to Output Delay
tPACC Page Access Time
113
113R
123
123R
Unit
tGLQV
tOE
Output Enable to Output Delay
Max
tEHQZ
tDF
Chip Enable to Output High Z (Note 1)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (Note 1)
Max
16
ns
tAXQX
tOH
Output Hold Time From Addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
Read
Output Enable Hold Time
(Note 1)
Toggle and
Data# Polling
Min
0
ns
tOEH
Min
10
ns
Notes:
1. Not 100% tested.
2. See Figure 12 and Table 13 for test specifications.
3. AC Specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC.
tRC
Addresses Stable
Addresses
tACC
CE#
tRH
tRH
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH Z
HIGH Z
Output Valid
Outputs
RESET#
RY/BY#
0V
Figure 14.
44
Read Operation Timings
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
AC CHARACTERISTICS
Same Page
A22-A2
A1-A0*
Aa
Ab
tPACC
tACC
Data Bus
Qa
Ad
Ac
tPACC
Qb
tPACC
Qc
Qd
CE#
OE#
* Figure shows word mode. Addresses are A1–A-1 for byte mode.
Figure 15.
September 9, 2003
Page Read Timings
Am29LV128MH/L
45
D A T A S H E E T
AC CHARACTERISTICS
Hardware Reset (RESET#)
Parameter
JEDEC
Std.
Description
All Speed Options
Unit
tReady
RESET# Pin Low (During Embedded Algorithms)
to Read Mode (See Note)
Max
20
µs
tReady
RESET# Pin Low (NOT During Embedded
Algorithms) to Read Mode (See Note)
Max
500
ns
tRP
RESET# Pulse Width
Min
500
ns
tRH
Reset High Time Before Read (See Note)
Min
50
ns
tRPD
RESET# Low to Standby Mode
Min
20
µs
tRB
RY/BY# Recovery Time
Min
0
ns
Note:
1.
Not 100% tested.
2.
AC Specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC.
RY/BY#
CE#, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Figure 16.
46
Reset Timings
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
AC CHARACTERISTICS
Erase and Program Operations
Parameter
Speed Options
JEDEC
Std.
Description
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# high
during toggle bit polling
Min
0
ns
tDVWH
tDS
Data Setup Time
Min
45
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
tOEPH
Output Enable High during toggle bit polling
Min
20
ns
tGHWL
tGHWL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tELWL
tCS
CE# Setup Time
Min
0
ns
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
35
ns
tWHDL
tWPH
Write Pulse Width High
Min
30
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
µs
Per Byte
Typ
7.5
µs
Per Word
Typ
15
µs
Per Byte
Typ
6.25
µs
Per Word
Typ
12.5
µs
Byte
Typ
60
µs
Word
Typ
60
µs
Byte
Typ
54
µs
Word
Typ
54
µs
tWLAX
Effective Write Buffer Program Operation
(Notes 2, 4)
tWHWH1
tWHWH1
Accelerated Effective Write Buffer Program
Operation (Notes 2, 4)
Single Byte Word
Program Operation (Note 2, 5)
Accelerated Single Byte Word Programming
Operation (Note 2, 5)
tWHWH2
93R
103, 103R
90
100
113, 113R 123, 123R Unit
110
120
ns
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
sec
tVHH
VHH Rise and Fall Time (Note 1)
Min
250
ns
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tBUSY
Erase/Program Valid to RY/BY# Delay
Min
90
ns
Notes:
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
3. For 1–16 words/1–32 bytes programmed.
4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation
5. Byte/Word programming specification is based upon a single word/byte programming operation not utilizing the write buffer.
6. AC Specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC.
September 9, 2003
Am29LV128MH/L
47
D A T A S H E E T
.
RY/BY#
CE#, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Figure 17.
48
Reset Timings
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
AC CHARACTERISTICS
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
555h
PA
PA
PA
tAH
CE#
tCH
OE#
tWHWH1
tWP
WE#
tWPH
tCS
tDS
tDH
PD
A0h
Data
Status
tBUSY
DOUT
tRB
RY/BY#
VCC
tVCS
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
2. Illustration shows device in word mode.
Figure 18.
Program Operation Timings
VHH
ACC
VIL or VIH
VIL or VIH
tVHH
Figure 19.
September 9, 2003
tVHH
Accelerated Program Timing Diagram
Am29LV128MH/L
49
D A T A S H E E T
AC CHARACTERISTICS
Erase Command Sequence (last two cycles)
tAS
tWC
2AAh
Addresses
Read Status Data
VA
SA
VA
555h for chip erase
tAH
CE#
tCH
OE#
tWP
WE#
tWPH
tCS
tWHWH2
tDS
tDH
Data
55h
In
Progress
30h
Complete
10 for Chip Erase
tBUSY
tRB
RY/BY#
tVCS
VCC
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”.
2. These waveforms are for the word mode.
Figure 20.
50
Chip/Sector Erase Operation Timings
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
AC CHARACTERISTICS
tRC
Addresses
VA
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
High Z
DQ7
Complement
Complement
DQ0–DQ6
Status Data
Status Data
True
Valid Data
High Z
True
Valid Data
tBUSY
RY/BY#
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data
read cycle.
Figure 21.
September 9, 2003
Data# Polling Timings (During Embedded Algorithms)
Am29LV128MH/L
51
D A T A S H E E T
AC CHARACTERISTICS
tAHT
tAS
Addresses
tAHT
tASO
CE#
tCEPH
tOEH
WE#
tOEPH
OE#
tDH
DQ6/DQ2
tOE
Valid
Status
Valid
Status
Valid
Status
(first read)
(second read)
(stops toggling)
Valid Data
Valid Data
RY/BY#
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status
read cycle, and array data read cycle
Figure 22.
Enter
Embedded
Erasing
WE#
Erase
Suspend
Erase
Toggle Bit Timings (During Embedded Algorithms)
Enter Erase
Suspend Program
Erase
Suspend
Program
Erase Suspend
Read
Erase
Resume
Erase Suspend
Read
Erase
Erase
Complete
DQ6
DQ2
Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle
DQ2 and DQ6.
Figure 23.
52
DQ2 vs. DQ6
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
AC CHARACTERISTICS
Temporary Sector Group Unprotect
Parameter
JEDEC
Std
Description
tVIDR
VID Rise and Fall Time (See Note)
tRSP
RESET# Setup Time for Temporary Sector
Unprotect
All Speed Options
Unit
Min
500
ns
Min
4
µs
Note:
1. Not 100% tested.
2. AC Specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC.
VID
RESET#
VID
VSS, VIL,
or VIH
VSS, VIL,
or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRRB
tRSP
RY/BY#
Figure 24.
September 9, 2003
Temporary Sector Group Unprotect Timing Diagram
Am29LV128MH/L
53
D A T A S H E E T
AC CHARACTERISTICS
VID
VIH
RESET#
SA, A6,
A1, A0
Valid*
Valid*
Sector Group Protect or Unprotect
Data
60h
60h
Valid*
Verify
40h
Status
Sector Group Protect: 150 µs,
Sector Group Unprotect: 15 ms
1 µs
CE#
WE#
OE#
* For sector group protect, A6 = 0, A1 = 1, A0 = 0. For sector group unprotect, A6 = 1, A1 = 1, A0 = 0.
Figure 25.
54
Sector Group Protect and Unprotect Timing Diagram
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
AC CHARACTERISTICS
Alternate CE# Controlled Erase and Program Operations
Parameter
Speed Options
JEDEC
Std.
Description
93R
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tELAX
tAH
Address Hold Time
Min
45
ns
tDVEH
tDS
Data Setup Time
Min
45
ns
tEHDX
tDH
Data Hold Time
Min
0
ns
tGHEL
tGHEL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tWLEL
tWS
WE# Setup Time
Min
0
ns
tEHWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE# Pulse Width
Min
45
ns
tEHEL
tCPH
CE# Pulse Width High
Min
30
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
µs
Per Byte
Typ
7.5
µs
Per Word
Typ
15
µs
Per Byte
Typ
6.25
µs
Per Word
Typ
12.5
µs
Byte
Typ
60
µs
Word
Typ
60
µs
Byte
Typ
54
µs
Word
Typ
54
µs
Typ
0.5
sec
Effective Write Buffer Program Operation
(Notes 2, 4)
tWHWH1
tWHWH1
Accelerated Effective Write Buffer Program
Operation (Notes 2, 4)
Single Byte Word
Program Operation (Note 2, 5)
Accelerated Single Byte Word
Programming Operation (Note 2, 5)
tWHWH2
tWHWH2
Sector Erase Operation (Note 2)
90
103, 103R 113, 113R 123, 123R
100
110
120
Unit
ns
Notes:
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
3. For 1–16 words/1–32 bytes programmed.
4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation.
5. Byte/Word programming specification is based upon a single word/byte programming operation not utilizing the write buffer.
6. AC Specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC.
September 9, 2003
Am29LV128MH/L
55
D A T A S H E E T
AC CHARACTERISTICS
PA for program
SA for sector erase
555 for chip erase
555 for program
2AA for erase
Data# Polling
Addresses
PA
tWC
tAS
tAH
tWH
WE#
tGHEL
OE#
tWHWH1 or 2
tCP
CE#
tWS
tCPH
tBUSY
tDS
tDH
DQ7#
Data
tRH
A0 for program
55 for erase
DOUT
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. Figure indicates last two bus cycles of a program or erase operation.
2. PA = program address, SA = sector address, PD = program data.
3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device.
4. Waveforms are for the word mode.
Figure 26.
Alternate CE# Controlled Write (Erase/Program)
Operation Timings
LATCHUP CHARACTERISTICS
Description
Min
Max
Input voltage with respect to VSS on all pins except I/O pins
(including A9, OE#, and RESET#)
–1.0 V
12.5 V
Input voltage with respect to VSS on all I/O pins
–1.0 V
VCC + 1.0 V
–100 mA
+100 mA
VCC Current
Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time.
56
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
ERASE AND PROGRAMMING PERFORMANCE
Parameter
Typ (Note 1)
Max (Note 2)
Unit
Comments
Sector Erase Time
0.5
3.5
sec
Chip Erase Time
128
256
sec
Excludes 00h programming
prior to erasure (Note 6)
Byte
60
600
µs
Word
60
600
µs
Byte
54
540
µs
Word
54
540
µs
240
1200
µs
Per Byte
7.5
38
µs
Per Word
15
75
µs
200
1040
µs
Per Byte
6.25
33
µs
Per Word
12.5
65
µs
126
292
sec
Single Byte/Word
Program Time (Note 3)
Accelerated Single Byte/Word
Program Time
(Note 3)
Total Write Buffer Program
Time (Note 4)
Effective Write Buffer Program
Time (Note 5)
Total Accelerated Write Buffer
Program Time (Note 4)
Effective Accelerated Write
Buffer Program Time
(Note 5)
Chip Program Time
Excludes system level
overhead (Note 8)
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC. Programming specifications assume that
all bits are programmed to 00h.
2. Maximum values are measured at VCC = 3.0, worst case temperature. Maximum values are valid up to and including 100,000
program/erase cycles.
3. Byte/Word programming specification is based upon a single word/byte programming operation not utilizing the write buffer.
4. For 1-16 words or 1-32 bytes programmed in a single write buffer programming operation.
5. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation.
6. The typical chip programming time is considerably less than the maximum chip programming time listed, since most words
program faster than the maximum program times listed.
7. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure.
8. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table
11 for further information on command definitions.
9. The device has a minimum erase and program cycle endurance of 100,000 cycles.
September 9, 2003
Am29LV128MH/L
57
D A T A S H E E T
TSOP PIN AND BGA PACKAGE CAPACITANCE
Parameter Symbol
Parameter Description
CIN
Input Capacitance
COUT
Output Capacitance
CIN2
Control Pin Capacitance
Test Setup
VIN = 0
VOUT = 0
VIN = 0
Typ
Max
Unit
TSOP
6
7.5
pF
BGA
4.2
5
pF
TSOP
8.5
12
pF
BGA
5.4
6.5
pF
TSOP
7.5
9
pF
BGA
3.9
4.7
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
DATA RETENTION
Parameter Description
Minimum Pattern Data Retention Time
58
Am29LV128MH/L
Test Conditions
Min
Unit
150°C
10
Years
125°C
20
Years
September 9, 2003
D A T A S H E E T
PHYSICAL DIMENSIONS
TS056/TSR056—56-Pin Standard/Reverse Thin Small Outline Package (TSOP)
PACKAGE
TS/TSR 56
JEDEC
MO-142 (B) EC
SYMBOL
NOTES:
MIN.
NOM.
MAX.
1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm).
(DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.)
A
---
---
1.20
2
PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
A1
0.05
---
0.15
3
PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN), INK OR LASER MARK.
A2
0.95
1.00
1.05
4
b1
0.17
0.20
0.23
b
c1
0.17
0.10
0.22
---
0.27
0.16
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS
DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE
LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE.
5
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE
MOLD PROTUSION IS 0.15 mm PER SIDE.
6
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE
DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b
DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm.
7
THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN
0.10 mm AND 0.25 mm FROM THE LEAD TIP.
8.
LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE
SEATING PLANE.
9
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
c
0.10
---
0.21
D
19.90
20.00
20.20
D1
18.30
18.40
18.50
E
13.90
14.00
14.10
0.50 BASIC
e
L
0.50
0.60
0.70
O
0˚
3˚
5˚
R
0.08
---
0.20
N
September 9, 2003
56
3160\38.10A
Am29LV128MH/L
59
D A T A S H E E T
PHYSICAL DIMENSIONS
LAA064—64-Ball Fortified Ball Grid Array
13 x 11 mm Package
60
Am29LV128MH/L
September 9, 2003
D A T A S H E E T
REVISION SUMMARY
Revision A (October 3, 2001)
Distinctive Characteristics
Initial release as abbreviated Advance Information
data sheet.
Revision A+1 (March 20, 2002)
Changed the typical sector erase time to TBD.
Changed the typical write buffer word programming
time to TBD.
Product Selector Guide
Distinctive Characteristics
Clarified description of Enhanced VersatileIO control.
Removed the 98R, 108, 108R, 118, 118R, 128, and
128R Speed Options.
Ordering Information
Replaced Note #2.
Corrected device density in device number/description.
Product Selector Guide and Read Only Operations
Physical Dimensions
Added a 30 ns Page Access time and Output Enable
Access time to the 113R and 123R Speed Options.
Added drawing that shows both TS056 and TSR056
specifications.
Ordering Information
Revision B (July 1, 2002)
Modified Order numbers and package markings to reflect the removal of speed options.
Expanded data sheet to full specification version.
Modified the VIO ranges.
Revision B+1 (September 16, 2002)
Added Notes #1 and #2.
Distinctive Characteristics, Physical Dimensions
Table 4. SecSi Sector Contents
Added 80-Ball Fine-Pitch BGA.
Added x8 and x16
Product Selector Guide
Operating Ranges
Added 80-Ball Fine-Pitch BGA.
Changed the VIO supply range to 1.65–3.6 V.
Added Note #1.
Added VIO (regulated voltage range) and VIO (full voltage range).
Added 103, 108, 113, 118, 123, 128 regulated OPNs.
Changed all OPNs that end with 4 or 9 to 3 or 8.
CMOS Compatible
Program Suspend/Program Resume Command
Sequence
Removed VIL, VIH, VOL, and VOH from table and added
V IL1 , V IH1 , V IL2 , V IH2 , V OL , V OH1 , and V OH2 from the
CMOS table in the Am29LV640MH/L datasheet.
Changed 1ms to 15µs maximum, with a typical of 5 µs.
Erase Suspend/Erase Resume Commands
Added that the device requires a typical of 5 µs.
Read-Only Operations, Erase Program Operations,
and Alternate CE# Controlled Erase and Program
Operations
Added regulated OPNs.
Changed all OPNs that end with 4 or 9 to 3 or 8.
Revision B+2 (November 11, 2002)
Global
Removed the Enhanced VI/O option and changed it to
VI/O only.
September 9, 2003
Erase and Programming Performance
Changed the typicals and/or maximums of Chip Erase
Time, Sector Erase Time, Effective Write Buffer Program Time, Program Time, and Accelerated Program
Time to TBD.
Customer Lockable: SecSi Sector NOT
Programmed or Protected at the factory.
Added second bullet, SecSi sector-protect verify text
and figure 3.
SecSi Sector Flash Memory Region, and Enter
SecSi Sector/Exit SecSi Sector Command
Sequence
Noted that the ACC function and unlock bypass modes
are not available when the SecSi sector is enabled.
Am29LV128MH/L
61
D A T A S H E E T
Byte/Word Program Command Sequence, Sector
Erase Command Sequence, and Chip Erase Command Sequence
Product Selector Guide
Removed 93R speed option.
Added note 2.
Noted that the SecSi Sector, autoselect, and CFI
functions are unavailable when a program or erase
operation is in progress.
Common Flash Memory Interface (CFI)
Changed wording in last sentence of third paragraph
from, “...the autoselect mode.” to “...reading array
data.”
Changed CFI website address
Ordering Information
Corrected Valid Combination to reflect speed option
changes.
Added Note.
AC Characteristics
Removed 93, 93R speed option.
Added Note
Revision B+3 (December 2, 2002)
Input values in the tWHWH 1 and tWHWH2 parameters in
the Erase and Program Options table that were previously TBD. Also added notes 5 and 6.
Global
Added sector group protection throughout datasheet
and added Table 4.
Product Selector Guide
Added VIOs to table and removed Note #2
Input values in the tWHWH 1 and tWHWH2 parameters in
the Alternate CE# Controlled Erase and Program Options table that were previously TBD. Also added notes
5.
Erase and Programming Performance
Ordering Information
Input values into table that were previously TBD.
Corrected typos in VIO ranges.
Added note 4.
Removed Notes #1 and 2.
Figure 6. Program Suspend/Program Resume
Change wait time to 15 µs.
Revision C (May 16, 2003)
Global
Converted to full datasheet version.
Operating Ranges
Modified SecSi Sector Flash Memory Region section
to include ESN references.
Corrected typos in VIO ranges.
Removed full voltage range.
Changed data sheet title to Am29LV128MH/L.
CMOS Compatible
Erase and Programming Performance
Changed VIH1 and VIH2 minimum to 1.9.
Input values into table that were previously TBD.
Removed typos in notes.
Modified notes.
Read-Only Characteristics
Revision C + 1 (June 11, 2003)
Added a 30 ns option to tPACC and tOE standard in table.
Product Selector Guide
Added note #3.
Added Note 2 to 113 and 123 speed grades
Hardware Reset, Erase and Program Operations,
Temporary Sector Unprotect, and Alternate CE#
Controlled Erase and Program Operations
Ordering Information
Added Note.
Revision B+4 (February 14, 2003)
Distinctive Characteristics
Corrected performance characteristics.
62
Modified speed grade options available, changed
speed grades mentioned in Note.
AC Characteristics, Erase and Program Operations
and Alternate CE# Controlled Erase and Program
Operations
Changed t WHWH1 Accelerated Effective Write Buffer
Program Operations value
Am29LV128MH/L
September 9, 2003
Revision C + 2 (September 9, 2003)
Global
Added 90 ns speed options and Ordering Part Numbers
Ordering Information
Added Note regarding Ordering Part Numbers.
Program Suspend/Program Resume Command
Sequence
Modified last paragraph.
Command Definitions, Table 10
Modified First Addr for Program/Erase Suspend and
Resume.
AC Characteristics
Added TRB, TBUSY specs.
Trademarks
Copyright © 2003 Advanced Micro Devices, Inc. All rights reserved.
AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.
ExpressFlash is a trademark of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.