PDS540 5A SCHOTTKY BARRIER RECTIFIER PowerDI ä5 NEW PRODUCT Features · Guard Ring Die Construction for Transient Protection · · · Low Power Loss, High Efficiency · · · High Forward Surge Current Capability · · · · · A2 b2 For Use in Low Voltage, High Frequency Inverters, Free Wheeling, and Polarity Protection Applications L1 E E1 Lead Free Finish "Green" Molding Compound (No Br, Sb) L1 LEFT PIN RIGHT PIN Mechanical Data · · PowerDIä5 A D Low Forward Voltage Drop e BOTTOMSIDE b1 HEAT SINK Note: Pins Left & Right must be electrically connected at the printed circuit board. Case: PowerDIä5 A2 b1 D D2 b2 Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 W Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 e3 A 1.05 1.15 0.33 0.43 b1 0.80 0.99 b2 1.70 1.88 D 3.90 4.05 3.05 NOM D2 6.40 5.30 E1 5.45 3.55 NOM E2 E 6.60 1.84 NOM e E2 Max A2 E L Moisture Sensitivity: Level 1 per J-STD-020C Min Dim L 0.75 0.95 L1 0.50 0.65 W 1.20 1.50 L1 e b1 b1 All Dimensions in mm Polarity: See Diagram Marking: See Page 3 Weight: 0.093 grams (approximate) Maximum Ratings @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also figure 5) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Operating Temperature Range Storage Temperature Range Thermal Characteristics Symbol Value Unit VRRM VRWM VR 40 V VR(RMS) 28 V IO 5 A IFSM 120 A Tj -55 to +150 °C TSTG -55 to +150 °C @ TA = 25°C unless otherwise specified Symbol Typ Max Unit Thermal Resistance Junction to Soldering Point Characteristic RqJS ¾ 4.0 °C/W Thermal Resistance Junction to Ambient Air (Note 1) RqJA 95 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 2) RqJA 70 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 3) RqJA 50 ¾ °C/W Notes: 1. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. 2. Polyimide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. 3. Polyimide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. DS30482 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDS540 ã Diodes Incorporated @ TA = 25°C unless otherwise specified Symbol Min Typ Max Unit V(BR)R 40 ¾ ¾ V IR = 0.5mA Forward Voltage VF ¾ ¾ ¾ ¾ 0.48 0.43 0.57 0.55 0.52 0.47 0.65 0.59 V IF = 5A, TS = 25°C IF = 5A, TS = 125°C IF = 10A, TS = 25°C IF = 10A, TS = 125°C Reverse Leakage Current (Note 4) IR ¾ ¾ ¾ 0.015 3 10 0.30 20 40 mA TS = 25°C, VR = 40V TS = 100°C, VR = 40V TS = 125°C, VR = 40V Characteristic Reverse Breakdown Voltage (Note 4) IF, INSTANTANEOUS FORWARD CURRENT (mA) Notes: Test Condition 4. Short duration test pulse used to minimize self-heating effect. 100 100000 10000 10 Tj = +25°C Tj = 150°C 1000 1 Tj = 125°C 100 Tj = 100°C 10 0.1 Tj = 85°C 1 Tj = -65°C 0.01 Tj = 25°C 0.1 Tj = -65°C 0.001 0.01 0 100 200 300 400 500 600 700 800 900 1000 20 10 0 VF, INSTANTANEOUS FORWARD VOLTAGE (mV) Fig. 1 Typical Forward Characteristics 40 30 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 800 100 700 Tj = +150°C CT, TOTAL CAPACITANCE (pF) IR, INSTANTANEOUS REVERSE CURRENT (mA) NEW PRODUCT Electrical Characteristics Tj = +125°C 10 Tj = +100°C 1 Tj = +85°C 0.1 f = 1 MHz 600 500 400 300 200 100 0 0.01 0 10 20 30 40 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 3 Typical Reverse Characteristics DS30482 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 2 of 3 www.diodes.com 0 5 10 15 20 25 30 35 40 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Total Capacitance vs. Reverse Voltage PDS540 4 PF, FORWARD POWER DISSIPATION (W) IF, DC FORWARD CURRENT (A) 6.0 4.5 Note 3 3.0 1.5 Note 1 0 IPK = 1 (DC) IAV 3 2 1 0 0 25 50 75 100 0 150 125 1 2 3 4 5 6 7 8 9 10 IF, FORWARD CURRENT (A) Fig. 6 Forward Power Dissipation TA, AMBIENT TEMPERATURE (°C) Fig. 5 DC Forward Current Derating 180 TA, DERATED AMBIENT TEMPERATURE (°C) NEW PRODUCT 7.5 Note 1 150 120 90 60 30 0 10 20 30 40 VR, DC REVERSE VOLTAGE (V) Fig. 7 Operating Temperature Derating Ordering Information Notes: 1. 2. 3. 4. 5. (Note 5) Device Packaging Shipping PDS540-13 PowerDIä5 5000/Tape & Reel FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. Short duration test pulse used to minimize self-heating effect. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information S540 YYWWK S540 = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last digit of year ex: 04 for 2004 WW = Week code 01 to 52 K = Factory Designator DS30482 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDS540