ONSEMI LP2950ACZ-5.0

LP2950, LP2951, NCV2951
100 mA, Low Power Low
Dropout Voltage Regulator
The LP2950 and LP2951 are micropower voltage regulators that are
specifically designed to maintain proper regulation with an extremely
low input−to−output voltage differential. These devices feature a very
low quiescent bias current of 75 mA and are capable of supplying
output currents in excess of 100 mA. Internal current and thermal
limiting protection is provided.
The LP2951 has three additional features. The first is the Error
Output that can be used to signal external circuitry of an out of
regulation condition, or as a microprocessor power−on reset. The
second feature allows the output voltage to be preset to 5.0 V, 3.3 V or
3.0 V output (depending on the version) or programmed from 1.25 V
to 29 V. It consists of a pinned out resistor divider along with direct
access to the Error Amplifier feedback input. The third feature is a
Shutdown input that allows a logic level signal to turn−off or turn−on
the regulator output.
Due to the low input−to−output voltage differential and bias current
specifications, these devices are ideally suited for battery powered
computer, consumer, and industrial equipment where an extension of
useful battery life is desirable. The LP2950 is available in the three
pin case 29 and DPAK packages, and the LP2951 is available in the
eight pin dual−in−line, SOIC−8 and Micro8 surface mount packages.
The ‘A’ suffix devices feature an initial output voltage tolerance
± 0.5%.
Features
• Pb−Free Packages are Available
• Low Quiescent Bias Current of 75 mA
• Low Input−to−Output Voltage Differential of 50 mV at 100 mA and
•
•
•
•
•
380 mV at 100 mA
5.0 V, 3.3 V or 3.0 V ±0.5% Allows Use as a Regulator or Reference
Extremely Tight Line and Load Regulation
Requires Only a 1.0 mF Output Capacitor for Stability
Internal Current and Thermal Limiting
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
LP2951 Additional Features
• Error Output Signals an Out of Regulation Condition
• Output Programmable from 1.25 V to 29 V
• Logic Level Shutdown Input
http://onsemi.com
TO−92
Z SUFFIX
CASE 29
1
Pin: 1. Output
2. Ground
3. Input
23
4
DPAK
DT SUFFIX
CASE 369C
1 2
3
PIN CONNECTIONS
1
2
3
Pin: 1. Input
2. Ground
3. Output
(Top View)
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
SOIC−8
D SUFFIX
CASE 751
8
1
PDIP−8
N SUFFIX
CASE 626
8
1
Micro8E
DM SUFFIX
CASE 846A
8
1
PIN CONNECTIONS
Output 1
8
Input
Sense 2
7
Feedback
Shutdown 3
6
VO Tap
GND 4
5
Error Output
(See Following Page for Device Information.)
(Top View)
ORDERING & MARKING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on pages 14 and 16 of this data sheet.
See general marking information in the device marking
section on page 18 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
December, 2006 − Rev. 19
1
Publication Order Number:
LP2950/D
LP2950, LP2951, NCV2951
DEVICE INFORMATION
Output Voltage
Package
3.0 V
3.3 V
5.0 V
Adjustable
Operating Ambient
Temperature Range
TO−92
Suffix Z
LP2950CZ−3.0
LP2950ACZ−3.0
LP2950CZ−3.3
LP2950ACZ−3.3
LP2950CZ−5.0
LP2950ACZ−5.0
Not
Available
TA = −40° to +125°C
DPAK
Suffix DT
LP2950CDT−3.0
LP2950ACDT−3.0
LP2950CDT−3.3
LP2950ACDT−3.3
LP2950CDT−5.0
LP2950ACDT−5.0
Not
Available
TA = −40° to +125°C
NCV2951ACD−3.3R2
NCV2951ACDR2
NCV2951CDR2
TA = −40° to +125°C
SOIC−8
−
SOIC−8
Suffix D
LP2951CD−3.0
LP2951ACD−3.0
LP2951CD−3.3
LP2951ACD−3.3
LP2951CD
LP2951ACD
LP2951CD
LP2951ACD
TA = −40° to +125°C
Micro8
Suffix DM
LP2951CDM−3.0
LP2951ACDM−3.0
LP2951CDM−3.3
LP2951ACDM−3.3
LP2951CDM
LP2951ACDM
LP2951CDM
LP2951ACDM
TA = −40° to +125°C
DIP−8
Suffix N
LP2951CN−3.0
LP2951ACN−3.0
LP2951CN−3.3
LP2951ACN−3.3
LP2951CN
LP2951ACN
LP2951CN
LP2951ACN
TA = −40° to +125°C
LP2950Cx−xx / LP2951Cxx−xx
LP2950ACx−xx / LP2951ACxx−xx
1% Output Voltage Precision at TA = 25°C
0.5% Output Voltage Precision at TA = 25°C
Input
Battery or
Unregulated DC
Output
182 k
Error Amplifier
60 k
1.23 V
Reference
GND
Battery or
Unregulated DC
5.0 V/100 mA
1.0 mF
1
3
Input
LP2950CZ−5.0
2
8
Output
1
Sense
5.0 V/100 mA
2
182 k
1.0 mF
VO Tap
6
60 k
7
From
3
CMOS/TTL
Feedback
Error
Amplifier
Shutdown
330 k
60 k
50 k
75 mV/
60 mV
Error
Output
To CMOS/TTL
5
Error Detection
Comparator
1.23 V
Reference
GND
4
LP2951CD or CN
This device contains 34 active transistors.
Figure 1. Representative Block Diagrams
http://onsemi.com
2
LP2950, LP2951, NCV2951
MAXIMUM RATINGS (TA = 25°C, unless otherwise noted.)
Rating
Input Voltage
Symbol
Value
Unit
VCC
30
Vdc
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁ
Peak Transient Input Voltage (t < 20 ms)
VCC
32
Vdc
PD
Internally Limited
W
Thermal Resistance, Junction−to−Ambient
RqJA
180
°C/W
Thermal Resistance, Junction−to−Case
RqJC
45
°C/W
Power Dissipation and Thermal Characteristics
Maximum Power Dissipation
Case 751(SOIC−8) D Suffix
Case 369A (DPAK) DT Suffix (Note 1)
Thermal Resistance, Junction−to−Ambient
RqJA
92
°C/W
Thermal Resistance, Junction−to−Case
RqJC
6.0
°C/W
Thermal Resistance, Junction−to−Ambient
RqJA
160
°C/W
Thermal Resistance, Junction−to−Case
RqJC
83
°C/W
RqJA
105
°C/W
RqJA
240
°C/W
Feedback Input Voltage
Vfb
−1.5 to +30
Vdc
Shutdown Input Voltage
Vsd
−0.3 to +30
Vdc
Error Comparator Output Voltage
Verr
−0.3 to +30
Vdc
Operating Ambient Temperature Range
TA
−40 to +125
°C
Maximum Die Junction Temperature Range
TJ
+150
°C
Storage Temperature Range
Tstg
−65 to +150
°C
Case 29 (TO−226AA/TO−92) Z Suffix
Case 626 N Suffix
Thermal Resistance, Junction−to−Ambient
Case 846A (Micro8) DM Suffix
Thermal Resistance, Junction−to−Ambient
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
3
LP2950, LP2951, NCV2951
ELECTRICAL CHARACTERISTICS (Vin = VO + 1.0 V, IO = 100 mA, CO = 1.0 mF, TA = 25°C [Note 3],
unless otherwise noted.)
Characteristic
Symbol
Output Voltage, 5.0 V Versions
Min
Typ
Max
VO
Unit
V
Vin = 6.0 V, IO = 100 mA, TA = 25°C
LP2950C−5.0/LP2951C/NCV2951C*
4.950
5.000
5.050
LP2950AC−5.0/LP2951AC/NCV2951AC*
4.975
5.000
5.025
LP2950C−5.0/LP2951C/NCV2951C*
4.900
−
5.100
LP2950AC−5.0/LP2951AC/NCV2951AC*
4.940
−
5.060
4.880
−
5.120
4.925
−
5.075
TA = − 40 to +125°C
Vin = 6.0 to 30 V, IO = 100 mA to 100 mA, TA = − 40 to +125°C
LP2950C−5.0/LP2951C/NCV2951C*
LP2950AC−5.0/LP2951AC/NCV2951AC*
Output Voltage, 3.3 V Versions
VO
V
Vin = 4.3 V, IO = 100 mA, TA = 25°C
LP2950C−3.3/LP2951C−3.3
3.267
3.300
3.333
LP2950AC−3.3/LP2951AC−3.3/NCV2951AC−3.3*
3.284
3.300
3.317
LP2950C−3.3/LP2951C−3.3
3.234
−
3.366
LP2950AC−3.3/LP2951AC−3.3/NCV2951AC−3.3*
3.260
−
3.340
LP2950C−3.3/LP2951C−3.3
3.221
−
3.379
LP2950AC−3.3/LP2951AC−3.3/NCV2951AC−3.3*
3.254
−
3.346
TA = − 40 to +125°C
Vin = 4.3 to 30 V, IO = 100 mA to 100 mA, TA = − 40 to +125°C
Output Voltage, 3.0 V Versions
VO
V
Vin = 4.0 V, IO = 100 mA, TA = 25°C
LP2950C−3.0/LP2951C−3.0
2.970
3.000
3.030
LP2950AC−3.0/LP2951AC−3.0
2.985
3.000
3.015
LP2950C−3.0/LP2951C−3.0
2.940
−
3.060
LP2950AC−3.0/LP2951AC−3.0
2.964
−
3.036
2.928
−
3.072
TA = − 40 to +125°C
Vin = 4.0 to 30 V, IO = 100 mA to 100 mA, TA = − 40 to +125°C
LP2950C−3.0/LP2951C−3.0
LP2950AC−3.0/LP2951AC−3.0
2.958
−
1. The Junction−to−Ambient Thermal Resistance is determined by PCB copper area per Figure 29.
2. This device series contains ESD protection and exceeds the following tests:
Human Body Model (HBM), 2000 V, Class 2, JESD22 A114−C
Machine Model (MM), 200 V, Class B, JESD22 A115−A
Charged Device Model (CDM), 2000 V, Class IV, JESD22 C101−C
3. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
4. VO(nom) is the part number voltage option.
5. Noise tests on the LP2951 are made with a 0.01 mF capacitor connected across Pins 7 and 1.
*NCV prefix is for automotive and other applications requiring site and change control.
http://onsemi.com
4
3.042
LP2950, LP2951, NCV2951
ELECTRICAL CHARACTERISTICS (continued) (Vin = VO + 1.0 V, IO = 100 mA, CO = 1.0 mF, TA = 25°C [Note 8],
unless otherwise noted.)
Symbol
Characteristic
Min
Typ
Max
−
−
0.08
0.04
0.20
0.10
−
−
0.13
0.05
0.20
0.10
−
−
30
350
80
450
−
−
93
4.0
120
12
mA
mA
ICCdropout
−
110
170
mA
ILimit
−
220
300
mA
Regthermal
−
0.05
0.20
%/W
−
−
126
56
−
−
1.210
1.220
1.235
1.235
1.260
1.250
1.200
1.200
−
−
1.270
1.260
Line Regulation (Vin = VO(nom) +1.0 V to 30 V) (Note 9)
LP2950C−XX/LP2951C/LP2951C−XX/NCV2951C*
LP2950AC−XX/LP2951AC/LP2951AC−XX/NCV2951AC*
Regline
Load Regulation (IO = 100 mA to 100 mA)
LP2950C−XX/LP2951C/LP2951C−XX/NCV2951C*
LP2950AC−XX/LP2951AC/LP2951AC−XX/NCV2951AC*
Regload
Dropout Voltage
IO = 100 mA
IO = 100 mA
VI − VO
Supply Bias Current
IO = 100 mA
IO = 100 mA
Unit
%
%
mV
ICC
Dropout Supply Bias Current (Vin = VO(nom) − 0.5 V,
IO = 100 mA) (Note 9)
Current Limit (VO Shorted to Ground)
Thermal Regulation
Output Noise Voltage (10 Hz to 100 kHz) (Note 10)
CL = 1.0 mF
CL = 100 mF
mVrms
Vn
LP2951A/LP2951AC Only
Reference Voltage (TA = 25°C)
LP2951C/LP2951C−XX/NCV2951C*
LP2951AC/LP2951AC−XX/NCV2951AC*
Vref
Reference Voltage (TA = − 40 to +125°C)
LP2951C/LP2951C−XX/NCV2951C*
LP2951AC/LP2951AC−XX/NCV2951AC*
Vref
Reference Voltage (TA = − 40 to +125°C)
IO = 100 mA to 100 mA, Vin = 23 to 30 V
LP2951C/LP2951C−XX/NCV2951C*
LP2951AC/LP2951AC−XX/NCV2951AC*
Vref
Feedback Pin Bias Current
V
V
V
1.185
1.190
−
−
1.285
1.270
IFB
−
15
40
nA
Output Leakage Current (VOH = 30 V)
Ilkg
−
0.01
1.0
mA
Output Low Voltage (Vin = 4.5 V, IOL = 400 mA)
VOL
−
150
250
mV
Upper Threshold Voltage (Vin = 6.0 V)
Vthu
40
45
−
mV
Lower Threshold Voltage (Vin = 6.0 V)
Vthl
−
60
95
mV
Hysteresis (Vin = 6.0 V)
Vhy
−
15
−
mV
0
2.0
−
−
0.7
30
−
−
35
450
50
600
−
3.0
10
Error Comparator
Shutdown Input
Input Logic Voltage
Logic “0” (Regulator “On”)
Logic “1” (Regulator “Off”)
Vshtdn
Shutdown Pin Input Current
Vshtdn = 2.4 V
Vshtdn = 30 V
Ishtdn
Regulator Output Current in Shutdown Mode
(Vin = 30 V, Vshtdn = 2.0 V, VO = 0, Pin 6 Connected to Pin 7)
Ioff
V
mA
6. The Junction−to−Ambient Thermal Resistance is determined by PCB copper area per Figure 29.
7. ESD data available upon request.
8. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
9. VO(nom) is the part number voltage option.
10. Noise tests on the LP2951 are made with a 0.01 mF capacitor connected across Pins 7 and 1.
*NCV prefix is for automotive and other applications requiring site and change control.
http://onsemi.com
5
mA
LP2950, LP2951, NCV2951
DEFINITIONS
Dropout Voltage − The input/output voltage differential
at which the regulator output no longer maintains regulation
against further reductions in input voltage. Measured when
the output drops 100 mV below its nominal value (which is
measured at 1.0 V differential), dropout voltage is affected
by junction temperature, load current and minimum input
supply requirements.
Line Regulation − The change in output voltage for a
change in input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that average chip temperature is not significantly
affected.
Load Regulation − The change in output voltage for a
change in load current at constant chip temperature.
Maximum Power Dissipation − The maximum total
device dissipation for which the regulator will operate
within specifications.
Bias Current − Current which is used to operate the
regulator chip and is not delivered to the load.
Output Noise Voltage − The RMS ac voltage at the
output, with constant load and no input ripple, measured
over a specified frequency range.
Leakage Current − Current drawn through a bipolar
transistor collector−base junction, under a specified
collector voltage, when the transistor is “off”.
Upper Threshold Voltage − Voltage applied to the
comparator input terminal, below the reference voltage
which is applied to the other comparator input terminal,
which causes the comparator output to change state from a
logic “0” to “1”.
Lower Threshold Voltage − Voltage applied to the
comparator input terminal, below the reference voltage
which is applied to the other comparator input terminal,
which causes the comparator output to change state from a
logic “1” to “0”.
Hysteresis − The difference between Lower Threshold
voltage and Upper Threshold voltage.
6.0
LP2951C
TA = 25°C
5.0
Vout , OUTPUT VOLTAGE (V)
LP2950/LP2951 BIAS CURRENT (mA)
10
1.0
0.1
0.01
0.1
1.0
10
4.0
RL = 50 W
3.0
2.0
1.0
0
100
RL = 50 kW
0
1.0
2.0
3.0
4.0
5.0
IL, LOAD CURRENT (mA)
Vin, INPUT VOLTAGE (V)
Figure 2. Quiescent Current
Figure 3. 5.0 V Dropout Characteristics over
Load
6.0
6.0
5.00
4.99
Vout , OUTPUT VOLTAGE (V)
Vout , OUTPUT VOLTAGE (V)
LP2951C
4.98
4.97
4.96
5.0
4.0
3.0
2.0
25°C
1.0
LP2951C
4.95
−50
125°C
−40°C
0
0
50
100
150
200
0
1.0
2.0
3.0
4.0
5.0
TA, AMBIENT TEMPERATURE (°C)
Vin, INPUT VOLTAGE (V)
Figure 4. Output Voltage versus Temperature
Figure 5. 5.0 V Dropout Characteristics with
RL = 50 W
http://onsemi.com
6
6.0
LP2950, LP2951, NCV2951
400
250
DROPOUT VOLTAGE (mV)
350
BIAS CURRENT (μ A)
200
0.1 mA Load Current
150
100
No Load
50
TA = 25°C
300
250
200
150
100
50
0
0.1
0
0
5.0
10
15
20
25
1.0
Figure 6. Input Current
Figure 7. Dropout Voltage versus Output Current
45
RL = 50
40
400
35
RL = 50 k
300
−50
0
50
Vout , OUTPUT VOLTAGE (V)
50
500
DROPOUT VOLTAGE (mV)R L= 50 k
DROPOUT VOLTAGE (mV)R L= 50
5.0
55
550
350
30
150
100
4.0
LP2951C
RL = 330 k
TA = 25°C
Vin Decreasing
3.0
Vin Increasing
2.0
1.0
0
4.70
4.74
T, TEMPERATURE (°C)
0
Vout
−2.0
6.5
TA = 25°C
CL = 1.0 mF
IL = 1.0 mA
VO = 5.0 V
5.5
0
100
200
300
400
−4.0
500
600
700
−6.0
800
SHUTDOWN AND OUTPUT VOLTAGE (V)
2.0
OUTPUT VOLTAGE CHANGE (mV)
Vin , INPUT VOLTAGE (V)
7.5
6.0
4.82
4.86
4.90
Figure 9. Error Comparator Output
4.0
Vin
7.0
4.78
Vin, INPUT VOLTAGE (V)
Figure 8. Dropout Voltage versus Temperature
8.0
100
IO, OUTPUT CURRENT (mA)
Vin, INPUT VOLTAGE (V)
450
10
7.0
CL = 1.0 mF
6.0
5.0
4.0
CL = 10 mF
3.0
2.0
1.0
Shutdown Input
TA = 25°C
IL = 10 mA
Vin = 8.0 V
Vout = 5.0 V
0
−1.0
−100
0
100
200
300
t, TIME (ms)
t, TIME (ms)
Figure 10. Line Transient Response
Figure 11. LP2951 Enable Transient
http://onsemi.com
7
400
LP2950, LP2951, NCV2951
150
400
200
Vout
100
0
50
−200
ILoad
0
RIPPLE REJECTION (dB)
80
CL = 1.0 mF
Vout = 5.0 V
IL = 400 mA to 75 mA
TA = 25°C
OUTPUT VOLTAGE CHANGE (mV)
LOAD CURRENT (mA)
200
60
IL= 0.1 mA
40
TA = 25°C
CL = 1.0 mF
Vin = 6.0 V
Vout = 5.0 V
20
−400
−50
0
0.5
1
1.5
2
2.5
3
3.5
0
1.0
4
10
CL = 1.0 mF
2.0
CL = 100 mF
10 k
Vout , OUTPUT CURRENT (mA)
Output Off"
1.2
Output On"
1.0
0
20
40
60
80
100
120
140
f, FREQUENCY (Hz)
t, TEMPERATURE (°C)
Figure 14. Output Noise
Figure 15. Shutdown Threshold Voltage
versus Temperature
TA = 25°C
80
2.0
TA = 75°C
60
0
40
−2.0
20
−4.0
LP2951CN
5.0
1.4
0.8
−40 −20
10
15
20
25
30
35
160
10000
4.0
0
1.6
100 k
100
0
1.8
SHUTDOWN THRESHOLD VOLTAGE (V)
IL= 100 mA
TA = 25°C
VO = 5.0 V
LP2951C
3.0
1.0 k
100 k
Figure 13. Ripple Rejection
OUTPUT VOLTAGE CHANGE (mV)
ESR (ohms)
VOLTAGE NOISE (μ V/√ Hz)
4.0
0
100
10 k
f, FREQUENCY (Hz)
Figure 12. Load Transient Response
1.0
1.0 k
100
t, TIME (ms)
Vout = 5 V
1000
−6.0
40
Unstable Region
100
Stable Region
10
1
0.1 mF
Unstable Region for 0.1 mF capacitor only
0.1
0.01
100 mF
Lower unstable region is for 0.1 mF only.
1 mF and 100 mF show no instability with low ESR values.
0
Vin, INPUT VOLTAGE (V)
10
20
30
40
50
60
70
80
90
100
Output Current (mA)
Figure 16. Maximum Rated
Output Current
Figure 17. Output Stability versus Output Capacitor
Change
http://onsemi.com
8
LP2950, LP2951, NCV2951
APPLICATIONS INFORMATION
Introduction
to the LP2951 is ramped up and down. The ERROR signal
becomes valid (low) at about 1.3 V input. It goes high when
the input reaches about 5.0 V (Vout exceeds about 4.75 V).
Since the LP2951’s dropout voltage is dependent upon the
load current (refer to the curve in the Typical Performance
Characteristics), the input voltage trip point will vary with
load current. The output voltage trip point does not vary
with load.
The error comparator output is an open collector which
requires an external pullup resistor. This resistor may be
returned to the output or some other voltage within the
system. The resistance value should be chosen to be
consistent with the 400 mA sink capability of the error
comparator. A value between 100 k and 1.0 MW is
suggested. No pullup resistance is required if this output is
unused.
When operated in the shutdown mode, the error
comparator output will go high if it has been pulled up to an
external supply. To avoid this invalid response, the error
comparator output should be pulled up to Vout (see
Figure 18).
The LP2950/LP2951 regulators are designed with
internal current limiting and thermal shutdown making them
user−friendly. Typical application circuits for the LP2950
and LP2951 are shown in Figures 20 through 28.
These regulators are not internally compensated and thus
require a 1.0 mF (or greater) capacitance between the
LP2950/LP2951 output terminal and ground for stability.
Most types of aluminum, tantalum or multilayer ceramic
will perform adequately. Solid tantalums or appropriate
multilayer ceramic capacitors are recommended for
operation below 25°C.
At lower values of output current, less output capacitance
is required for output stability. The capacitor can be reduced
to 0.33 mF for currents less than 10 mA, or 0.1 mF for currents
below 1.0 mA. Using the 8 pin versions at voltages less than
5.0 V operates the error amplifier at lower values of gain, so
that more output capacitance is needed for stability. For the
worst case operating condition of a 100 mA load at 1.23 V
output (output Pin 1 connected to the feedback Pin 7) a
minimum capacitance of 3.3 mF is recommended.
The LP2950 will remain stable and in regulation when
operated with no output load. When setting the output
voltage of the LP2951 with external resistors, the resistance
values should be chosen to draw a minimum of 1.0 mA.
A bypass capacitor is recommended across the
LP2950/LP2951 input to ground if more than 4 inches of
wire connects the input to either a battery or power supply
filter capacitor.
Input capacitance at the LP2951 Feedback Pin 7 can
create a pole, causing instability if high value external
resistors are used to set the output voltage. Adding a 100 pF
capacitor between the Output Pin 1 and the Feedback Pin 7
and increasing the output filter capacitor to at least 3.3 mF
will stabilize the feedback loop.
5.0 V
4.75 V
Output
Voltage
ERROR
Not
Valid
Not
Valid
4.75 V + Vdropout
Input
Voltage
4.70 V
1.3 V
Pullup
to Ext
Pullup
to Vout
4.70 V + Vdropout
1.3 V
Error Detection Comparator
The comparator switches to a positive logic low whenever
the LP2951 output voltage falls more than approximately
5.0% out of regulation. This value is the comparator’s
designed−in offset voltage of 60 mV divided by the 1.235 V
internal reference. As shown in the representative block
diagram. This trip level remains 5.0% below normal
regardless of the value of regulated output voltage. For
example, the error flag trip level is 4.75 V for a normal 5.0 V
regulated output, or 9.50 V for a 10 V output voltage.
Figure 2 is a timing diagram which shows the ERROR
signal and the regulated output voltage as the input voltage
Figure 18. ERROR Output Timing
Programming the Output Voltage (LP2951)
The LP2951CX may be pin−strapped for the nominal
fixed output voltage using its internal voltage divider by
tying Pin 1 (output) to Pin 2 (sense) and Pin 7 (feedback) to
Pin 6 (5.0 V tap). Alternatively, it may be programmed for
any output voltage between its 1.235 reference voltage and
its 30 V maximum rating. An external pair of resistors is
required, as shown in Figure 19.
http://onsemi.com
9
LP2950, LP2951, NCV2951
Vin
100 k
Error
Output
5
8
Vin
Error
Vout
SNS
Shutdown
Input
3
SD
VO T
for reducing noise on the 3 lead LP2950. However,
increasing the capacitor from 1.0 mF to 220 mF only
decreases the noise from 430 mV to 160 mVrms for a 100 kHz
bandwidth at the 5.0 V output.
Noise can be reduced fourfold by a bypass capacitor
across R1, since it reduces the high frequency gain from 4
to unity. Pick
1
2
Vout
1.23 to 30 V
NC
6 NC R1
0.01 mF
C
3.3 mF
Bypass
[
1
2pR1 x 200 Hz
or about 0.01 mF. When doing this, the output capacitor must
be increased to 3.3 mF to maintain stability. These changes
reduce the output noise from 430 mV to 126 mVrms for a
100 kHz bandwidth at 5.0 V output. With bypass
capacitor added, noise no longer scales with output voltage
so that improvements are more dramatic at higher output
voltages.
GND FB
4
7
R2
Figure 19. Adjustable Regulator
Unregulated
Input
The complete equation for the output voltage is:
V
+ V (1 ) R1ńR2) ) I
R1
out
ref
MTB23P06E
1.0 mF
FB
where Vref is the nominal 1.235 V reference voltage and IFB
is the feedback pin bias current, nominally −20 nA. The
minimum recommended load current of 1.0 mA forces an
upper limit of 1.2 MW on the value of R2, if the regulator
must work with no load. IFB will produce a 2% typical error
in Vout which may be eliminated at room temperature by
adjusting R1. For better accuracy, choosing R2 = 100 k
reduces this error to 0.17% while increasing the resistor
program current to 12 mA. Since the LP2951 typically draws
75 mA at no load with Pin 2 open circuited, the extra 12 mA
of current drawn is often a worthwhile tradeoff for
eliminating the need to set output voltage in test.
Error
Output
10 k
5 Error
0.01 mF
8
Vin
Vout
5.0 V ±1.0%
0 to 1.0 A
Vout
SNS
LP2951CN
Shutdown
Input
3
SD
VO T
1
2
6
220 mF
GND FB
4
7
0.002 mF
1.0 M
2.0 k
Output Noise
In many applications it is desirable to reduce the noise
present at the output. Reducing the regulator bandwidth by
increasing the size of the output capacitor is the only method
Figure 20. 1.0 A Regulator with 1.2 V Dropout
http://onsemi.com
10
LP2950, LP2951, NCV2951
TYPICAL APPLICATIONS
+V = 2.0 to 30 V
IL
IL = 1.23/R
Load
Unregulated Input
6.0 to 10 Vdc
8
Vin
8
NC
5 Error
Vin
Vout
1N4001
1
2
NC
SNS
0.1 mF LP2951CN
3
6 NC
SD
VO T
330 pF
GND FB
4
7
2.2 mF
4.2 V ±0.025 V
Error
Output
2.0 M
1.0%
806 k
1.0%
Shutdown
Input
5
0.1 mF
Vout
Error
1
2
SNS
LP2951CN
3
6
SD
VO T
GND FB
4
7
Lithium Ion
Rechargeable
Cell
50 k
1.0 mF
R
GND
Figure 21. Lithium Ion Battery Cell Charger
Figure 22. Low Drift Current Sink
+Vin
+Vin
8
Vin
470 k
2N3906
5
470 k
Reset
Normally
Closed
Error
Vout
SNS
LP2951CN
3
SD
CMOS
Gate
*Sleep
Input
VO T
1
2
Vout
8
Vin
47 k
NC
6 NC
Error
Output
R1
GND FB
4
7
1.0 mF Shutdown
Input
5
Error
Error flag occurs when Vin is too
low to maintain Vout, or if Vout is reduced by excessive load current.
Vout
SNS
LP2951CN
3
SD
GND
4
R2
470 k
VO T
2
Vout
2N3906
1
NC
200 k
3.3 mF
6 NC
100 k 100 pF
FB
7
100 k
Figure 23. Latch Off When Error Flag Occurs
Figure 24. 5.0 V Regulator with 2.5 V Sleep Function
http://onsemi.com
11
LP2950, LP2951, NCV2951
+Vin
5
NC
8
Vin
Error
Vout
D2
1
2
SNS
LP2951CN
3
#1
6
SD
VO T
D1
Memory
V+
1.0 mF
20
3.6 V
NiCad
GND FB
4
7
Early Warning
27 k
All diodes are 1N4148.
D3
Reset
2.7 M
Q1
Early Warning flag on low input voltage.
mP
D4
VDD
2N3906
8
Vin
330 k
5
Battery backup on auxiliary output.
Vout
Error
1
Operation: Regulator #1’s Vout is programmed one
diode drop above 5.0 V. Its error flag becomes active
when Vin < 5.7 V. When Vin drops below 5.3 V, the
error flag of regulator #2 becomes active and via Q1
latches the main output “off”. When Vin again exceeds
5.7 V, regulator #1 is back in regulation and the early
warning signal rises, unlatching regulator #2 via D3.
Main
Output
2
SNS
LP2951CN
#2
3
6
SD
VO T
GND
4
Main output latches off at lower input voltages.
1.0 mF
FB
7
Figure 25. Regulator with Early Warning and Auxiliary Output
+Vin
Current Limit
Section
0.05
470
680
2N3906
1000 mF
2N3906
MJE2955
.33 mF
10 k
4.7 M
Error
Flag
5
8
Vin
Error
Vout
SNS
LP2951CN
220
3
SD
VO T
GND FB
4
7
20 k
1
2
NC
6 NC
.01 mF
Vout @ 2.0 A
47
4.7 mF
Tant
100 mF
R1
R2
0.033 mF
Vout = 1.25V (1.0 + R1/R2)
For 5.0 V output, use internal resistors. Wire Pin 6 to 7,
and wire Pin 2 to +Vout Bus.
Figure 26. 2.0 A Low Dropout Regulator
http://onsemi.com
12
LP2950, LP2951, NCV2951
+ 5.0 V
4.7 k
Output*
1
4
20 mA
5
NC
8
Vin
Error
Vout
SNS
LP2951CN
3
NC
1N4001
5
0.1 mF
SD
VO T
Gnd
4
2
1
2
4
NC
6
* High for
IL < 3.5 mA
NC
FB
7
1N457
360
1N457
1N457
Figure 27. Open Circuit Detector for 4.0 to 20 mA Current Loop
31.6 k
100 k
2
NC
1
5
8
Vin
Error
Vout
SNS
LP2951CN
3
3
SD
VO T
Gnd
4
1
Main V+
2
Memory V+
1.0 mF
6
20
NC
NiCad Backup
Battery
FB
7
NC
Figure 28. Low Battery Disconnect
JUNCTION-TO-AIR (° C/W)
R θ JA, THERMAL RESISTANCE
100
2.4
PD(max) for TA = 50°C
Free Air
Mounted
Vertically
90
2.0
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
80
Minimum
Size Pad
70
60
50
2.0 oz. Copper
L
1.6
L
1.2
0.8
0.4
RqJA
40
0
0
5.0
10
15
20
25
30
L, LENGTH OF COPPER (mm)
Figure 29. DPAK Thermal Resistance and Maximum
Power Dissipation versus PCB Copper Length
http://onsemi.com
13
PD, MAXIMUM POWER DISSIPATION (W)
MC34164P−5
6.0 V Lead−Acid
Battery
2N3906
LP2950, LP2951, NCV2951
ORDERING INFORMATION (LP2950)
Output Voltage
(Volts)
Tolerance (%)
Package
Shipping †
LP2950CZ−3.0
3.0
1.0
TO−92
2000 Units / Bag
LP2950CZ−3.0G
3.0
1.0
TO−92
(Pb−Free)
2000 Units / Bag
LP2950CZ−3.0RA
3.0
1.0
TO−92
2000 Units / Tape & Reel
LP2950CZ−3.0RAG
3.0
1.0
TO−92
(Pb−Free)
2000 Units / Tape & Reel
LP2950ACZ−3.0
3.0
0.5
TO−92
2000 Units / Bag
LP2950ACZ−3.0G
3.0
0.5
TO−92
(Pb−Free)
2000 Units / Bag
LP2950ACZ−3.0RA
3.0
0.5
TO−92
2000 Units / Tape & Reel
LP2950ACZ−3.0RAG
3.0
0.5
TO−92
(Pb−Free)
2000 Units / Tape & Reel
LP2950CZ−3.3
3.3
1.0
TO−92
2000 Units / Bag
LP2950CZ−3.3G
3.3
1.0
TO−92
(Pb−Free)
2000 Units / Bag
LP2950CZ−3.3RA
3.3
1.0
TO−92
2000 Units / Tape & Reel
LP2950CZ−3.3RAG
3.3
1.0
TO−92
(Pb−Free)
2000 Units / Tape & Reel
LP2950ACZ−3.3
3.3
0.5
TO−92
2000 Units / Bag
LP2950ACZ−3.3G
3.3
0.5
TO−92
(Pb−Free)
2000 Units / Bag
LP2950ACZ−3.3RA
3.3
0.5
TO−92
2000 Units / Tape & Reel
LP2950ACZ−3.3RAG
3.3
0.5
TO−92
(Pb−Free)
2000 Units / Tape & Reel
LP2950CZ−5.0
5.0
1.0
TO−92
2000 Units / Bag
LP2950CZ−5.0G
5.0
1.0
TO−92
(Pb−Free)
2000 Units / Bag
LP2950CZ−5.0RA
5.0
1.0
TO−92
2000 Units / Tape & Reel
LP2950CZ−5.0RAG
5.0
1.0
TO−92
(Pb−Free)
2000 Units / Tape & Reel
LP2950CZ−5.0RP
5.0
1.0
TO−92
2000 Units / Ammo Pack
LP2950CZ−5.0RPG
5.0
1.0
TO−92
(Pb−Free)
2000 Units / Ammo Pack
LP2950ACZ−5.0
5.0
0.5
TO−92
2000 Units / Bag
LP2950ACZ−5.0G
5.0
0.5
TO−92
(Pb−Free)
2000 Units / Bag
LP2950ACZ−5.0RA
5.0
0.5
TO−92
2000 Units / Tape & Reel
LP2950ACZ−5.0RAG
5.0
0.5
TO−92
(Pb−Free)
2000 Units / Tape & Reel
LP2950CDT−3.0
3.0
1.0
DPAK
75 Units / Rail
LP2950CDT−3.0G
3.0
1.0
DPAK
(Pb−Free)
75 Units / Rail
LP2950CDT−3.0RK
3.0
1.0
DPAK
2500 Units / Tape & Reel
LP2950CDT−3.0RKG
3.0
1.0
DPAK
(Pb−Free)
2500 Units / Tape & Reel
LP2950ACDT−3.0
3.0
0.5
DPAK
75 Units / Rail
LP2950ACDT−3.0G
3.0
0.5
DPAK
(Pb−Free)
75 Units / Rail
LP2950ACDT−3.0RK
3.0
0.5
DPAK
2500 Units / Tape & Reel
LP2950ACDT−3RKG
3.0
0.5
DPAK
(Pb−Free)
2500 Units / Tape & Reel
LP2950CDT−3.3
3.3
1.0
DPAK
75 Units / Rail
Part Number
http://onsemi.com
14
LP2950, LP2951, NCV2951
ORDERING INFORMATION (LP2950)
Output Voltage
(Volts)
Tolerance (%)
Package
Shipping †
LP2950CDT−3.3G
3.3
1.0
DPAK
(Pb−Free)
75 Units / Rail
LP2950CDT−3.3RK
3.3
1.0
DPAK
2500 Units / Tape & Reel
LP2950CDT−3.3RKG
3.3
1.0
DPAK
(Pb−Free)
2500 Units / Tape & Reel
LP2950ACDT−3.3
3.3
0.5
DPAK
75 Units / Rail
LP2950ACDT−3.3RG
3.3
0.5
DPAK
(Pb−Free)
75 Units / Rail
LP2950ACDT−3.3RK
3.3
0.5
DPAK
2500 Units / Tape & Reel
LP2950CDT−5.0
5.0
1.0
DPAK
75 Units / Rail
LP2950CDT−5.0G
5.0
1.0
DPAK
(Pb−Free)
75 Units / Rail
LP2950CDT−5.0RK
5.0
1.0
DPAK
2500 Units / Tape & Reel
LP2950CDT−5.0RKG
5.0
1.0
DPAK
(Pb−Free)
2500 Units / Tape & Reel
LP2950ACDT−5.0
5.0
0.5
DPAK
75 Units / Rail
LP2950ACDT−5.0G
5.0
0.5
DPAK
(Pb−Free)
75 Units / Rail
LP2950ACDT−5.0RK
5.0
0.5
DPAK
2500 Units / Tape & Reel
LP2950ACDT−5RKG
5.0
0.5
DPAK
(Pb−Free)
2500 Units / Tape & Reel
Part Number
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
15
LP2950, LP2951, NCV2951
ORDERING INFORMATION (LP2951)
Output Voltage
(Volts)
Tolerance (%)
Package
Shipping †
LP2951CD−3.0
3.0
1.0
SOIC−8
98 Units / Rail
LP2951CD−3.0G
3.0
1.0
SOIC−8
(Pb−Free)
98 Units / Rail
LP2951CD−3.0R2
3.0
1.0
SOIC−8
2500 Units / Tape & Reel
LP2951CD−3.0R2G
3.0
1.0
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
LP2951ACD−3.0
3.0
0.5
SOIC−8
98 Units / Rail
LP2951ACD−3.0G
3.0
0.5
SOIC−8
(Pb−Free)
98 Units / Rail
LP2951ACD−3.0R2
3.0
0.5
SOIC−8
2500 Units / Tape & Reel
LP2951ACD−3.0R2G
3.0
0.5
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
LP2951CD−3.3
3.3
1.0
SOIC−8
98 Units / Rail
LP2951CD−3.3G
3.3
1.0
SOIC−8
(Pb−Free)
98 Units / Rail
LP2951CD−3.3R2
3.3
1.0
SOIC−8
2500 Units / Tape & Reel
LP2951CD−3.3R2G
3.3
1.0
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
LP2951ACD−3.3
3.3
0.5
SOIC−8
98 Units / Rail
LP2951ACD−3.3G
3.3
0.5
SOIC−8
(Pb−Free)
98 Units / Rail
LP2951ACD−3.3R2
3.3
0.5
SOIC−8
2500 Units / Tape & Reel
LP2951ACD−3.3R2G
3.3
0.5
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
LP2951CD
5.0 or Adj.
1.0
SOIC−8
98 Units / Rail
LP2951CDG
5.0 or Adj.
1.0
SOIC−8
(Pb−Free)
98 Units / Rail
LP2951CDR2
5.0 or Adj.
1.0
SOIC−8
2500 Units / Tape & Reel
LP2951CDR2G
5.0 or Adj.
1.0
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
LP2951ACD
5.0 or Adj.
0.5
SOIC−8
98 Units / Rail
LP2951ACDG
5.0 or Adj.
0.5
SOIC−8
(Pb−Free)
98 Units / Rail
LP2951ACDR2
5.0 or Adj.
0.5
SOIC−8
2500 Units / Tape & Reel
LP2951ACDR2G
5.0 or Adj.
0.5
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
LP2951CDM−3.0R2
3.0
1.0
Micro8
4000 Units / Tape & Reel
LP2951CDM−3.0R2G
3.0
1.0
Micro8
(Pb−Free)
4000 Units / Tape & Reel
LP2951ACDM−3.0R2
3.0
0.5
Micro8
4000 Units / Tape & Reel
LP2951CDM−3.3R2
3.3
1.0
Micro8
4000 Units / Tape & Reel
LP2951CDM−3.3R2G
3.3
1.0
Micro8
(Pb−Free)
4000 Units / Tape & Reel
LP2951ACDM−3.3RG
3.3
0.5
Micro8
(Pb−Free)
4000 Units / Tape & Reel
LP2951ACDM−3.3R2
3.3
0.5
Micro8
4000 Units / Tape & Reel
LP2951CDMR2
5.0 or Adj.
1.0
Micro8
4000 Units / Tape & Reel
LP2951CDMR2G
5.0 or Adj.
1.0
Micro8
(Pb−Free)
4000 Units / Tape & Reel
LP2951ACDMR2
5.0 or Adj.
0.5
Micro8
4000 Units / Tape & Reel
LP2951ACDMR2G
5.0 or Adj.
0.5
Micro8
(Pb−Free)
4000 Units / Tape & Reel
Part Number
http://onsemi.com
16
LP2950, LP2951, NCV2951
ORDERING INFORMATION (LP2951)
Output Voltage
(Volts)
Tolerance (%)
Package
Shipping †
5.0 or Adj.
0.5
Micro8
4000 Units / Tape & Reel
LP2951CN−3.0
3.0
1.0
PDIP−8
50 Units / Rail
LP2951CN−3.0G
3.0
1.0
PDIP−8
(Pb−Free)
50 Units / Rail
LP2951ACN−3.0
3.0
0.5
PDIP−8
50 Units / Rail
LP2951ACN−3.0G
3.0
0.5
PDIP−8
(Pb−Free)
50 Units / Rail
LP2951CN−3.3
3.3
1.0
PDIP−8
50 Units / Rail
LP2951CN−3.3G
3.3
1.0
PDIP−8
(Pb−Free)
50 Units / Rail
LP2951ACN−3.3
3.3
0.5
PDIP−8
50 Units / Rail
LP2951ACN−3.3G
3.3
0.5
PDIP−8
(Pb−Free)
50 Units / Rail
LP2951CN
5.0 or Adj.
1.0
PDIP−8
50 Units / Rail
LP2951CNG
5.0 or Adj.
1.0
PDIP−8
(Pb−Free)
50 Units / Rail
LP2951ACN
5.0 or Adj.
0.5
PDIP−8
50 Units / Rail
LP2951ACNG
5.0 or Adj.
0.5
PDIP−8
(Pb−Free)
50 Units / Rail
Part Number
LP2951ACDM−5.0R2
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
ORDERING INFORMATION (NCV2951)
Output Voltage
(Volts)
Tolerance (%)
Package
Shipping †
NCV2951ACD−3.3R2*
3.3
0.5
SOIC−8
2500 Units / Tape & Reel
NCV2951ACD3.3R2G
3.3
0.5
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
NCV2951ACDR2*
5.0 or Adj.
0.5
SOIC−8
2500 Units / Tape & Reel
NCV2951ACDR2G
5.0 or Adj.
0.5
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
NCV2951CDR2*
5.0 or Adj.
1.0
SOIC−8
2500 Units / Tape & Reel
NCV2951CDR2G*
5.0 or Adj.
1.0
SOIC−8
(Pb−Free)
2500 Units / Tape & Reel
Part Number
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV prefix is for automotive and other applications requiring site and control changes.
http://onsemi.com
17
LP2950, LP2951, NCV2951
MARKING DIAGRAMS
TO−92
Z SUFFIX
CASE 029
2950
CZ−xx
ALYWWG
G
DPAK
DT SUFFIX
CASE 369C
2950A
CZ−xx
ALYWWG
G
50−yG
ALYWW
50−yyG
ALYWW
50AyyG
ALYWW
50A−yG
ALYWW
SOIC−8
D SUFFIX
CASE 751
8
8
51z
ALYW
G
1
*
8
51z−33
ALYW
G
1
*
51z−3
ALYW
G
1
PDIP−8
N SUFFIX
CASE 626
8
8
51CN
AWL
YYWWG
1
8
51ACN
AWL
YYWWG
1
Micro8
DM SUFFIX
CASE 846A
8
51CN−xx
AWL
YYWWG
1
8
51ACN−xx
AWL
YYWWG
1
xx
= 3.0, 3.3, or 5.0
y
= 3 or 5
yy
= 30, 33, or 50
z
= A or C
A
= Assembly Location
WL, L = Wafer Lot
YY, Y
= Year
WW, W = Work Week
G
= Pb−Free Package
G
= Pb−Free Package
(Note: Microdot may be in either location)
*This marking diagram also applies to NCV2951.
http://onsemi.com
18
8
PAxx
AYWG
G
1
P−xx
AYWG
G
1
LP2950, LP2951, NCV2951
PACKAGE DIMENSIONS
TO−226AA/TO−92
Z SUFFIX
PLASTIC PACKAGE
CASE 29−11
ISSUE AL
A
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
B
R
P
L
SEATING
PLANE
K
DIM
A
B
C
D
G
H
J
K
L
N
P
R
V
D
X X
G
J
H
V
C
SECTION X−X
1
N
N
http://onsemi.com
19
INCHES
MIN
MAX
0.175
0.205
0.170
0.210
0.125
0.165
0.016
0.021
0.045
0.055
0.095
0.105
0.015
0.020
0.500
−−−
0.250
−−−
0.080
0.105
−−− 0.100
0.115
−−−
0.135
−−−
MILLIMETERS
MIN
MAX
4.45
5.20
4.32
5.33
3.18
4.19
0.407
0.533
1.15
1.39
2.42
2.66
0.39
0.50
12.70
−−−
6.35
−−−
2.04
2.66
−−−
2.54
2.93
−−−
3.43
−−−
LP2950, LP2951, NCV2951
PACKAGE DIMENSIONS
DPAK
DT SUFFIX
PLASTIC PACKAGE
CASE 369C−01
ISSUE O
−T−
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
E
R
4
Z
A
S
1
2
DIM
A
B
C
D
E
F
G
H
J
K
L
R
S
U
V
Z
3
U
K
F
J
L
H
D
G
2 PL
0.13 (0.005)
M
T
SOLDERING FOOTPRINT*
6.20
0.244
3.0
0.118
2.58
0.101
5.80
0.228
1.6
0.063
6.172
0.243
SCALE 3:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details please download the ON Semiconductor Soldering and
Mozunting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
20
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.027 0.035
0.018 0.023
0.037 0.045
0.180 BSC
0.034 0.040
0.018 0.023
0.102 0.114
0.090 BSC
0.180 0.215
0.025 0.040
0.020
−−−
0.035 0.050
0.155
−−−
MILLIMETERS
MIN
MAX
5.97
6.22
6.35
6.73
2.19
2.38
0.69
0.88
0.46
0.58
0.94
1.14
4.58 BSC
0.87
1.01
0.46
0.58
2.60
2.89
2.29 BSC
4.57
5.45
0.63
1.01
0.51
−−−
0.89
1.27
3.93
−−−
LP2950, LP2951, NCV2951
PACKAGE DIMENSIONS
SOIC−8
D SUFFIX
PLASTIC PACKAGE
CASE 751−07
ISSUE AH
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
1
0.25 (0.010)
M
Y
M
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
21
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
LP2950, LP2951, NCV2951
PACKAGE DIMENSIONS
PDIP−8
N SUFFIX
PLASTIC PACKAGE
CASE 626−05
ISSUE L
8
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5
−B−
1
4
F
−A−
NOTE 2
L
C
J
−T−
N
SEATING
PLANE
D
H
M
K
G
0.13 (0.005)
M
T A
M
B
M
http://onsemi.com
22
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MILLIMETERS
MIN
MAX
9.40
10.16
6.10
6.60
3.94
4.45
0.38
0.51
1.02
1.78
2.54 BSC
0.76
1.27
0.20
0.30
2.92
3.43
7.62 BSC
−−−
10 _
0.76
1.01
INCHES
MIN
MAX
0.370
0.400
0.240
0.260
0.155
0.175
0.015
0.020
0.040
0.070
0.100 BSC
0.030
0.050
0.008
0.012
0.115
0.135
0.300 BSC
−−−
10_
0.030
0.040
LP2950, LP2951, NCV2951
PACKAGE DIMENSIONS
Micro8E
DM SUFFIX
PLASTIC PACKAGE
CASE 846A−02
ISSUE G
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A−01 OBSOLETE, NEW STANDARD 846A−02.
D
HE
PIN 1 ID
E
DIM
A
A1
b
c
D
E
e
L
HE
e
b 8 PL
0.08 (0.003)
T B
M
S
A
S
SEATING
−T− PLANE
0.038 (0.0015)
MILLIMETERS
NOM
MAX
−−
1.10
0.08
0.15
0.33
0.40
0.18
0.23
3.00
3.10
3.00
3.10
0.65 BSC
0.40
0.55
0.70
4.75
4.90
5.05
MIN
−−
0.05
0.25
0.13
2.90
2.90
A
A1
L
c
SOLDERING FOOTPRINT*
1.04
8X
0.041
0.38
0.015
3.20
0.126
6X
8X
4.24
0.167
0.65
0.0256
5.28
0.208
SCALE 8:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
23
INCHES
NOM
−−
0.003
0.013
0.007
0.118
0.118
0.026 BSC
0.021
0.016
0.187
0.193
MIN
−−
0.002
0.010
0.005
0.114
0.114
MAX
0.043
0.006
0.016
0.009
0.122
0.122
0.028
0.199
LP2950, LP2951, NCV2951
SENSEFET is a trademark of Semiconductor Components Industries, LLC.
Micro8 is a trademark of International Rectifier.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
24
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LP2950/D