SPICE MODEL: PDS5100H PDS5100H 5A HIGH VOLTAGE SCHOTTKY BARRIER RECTIFIER PowerDI ä5 Features · Guard Ring Die Construction for Transient Protection · · · · · · · · High Maximum Junction Temperature A2 b2 Very Low Leakage Current L1 PowerDIä5 Highly Stable Oxide Passivated Junction E Low Forward Voltage Drop E1 High Forward Surge Current Capability L1 Lead Free Finish, RoHS Compliant (Note 1) e "Green" Molding Compound (No Br, Sb) Qualified to AEC-Q101 Standards for High Reliability A2 b1 b1 D D2 b2 Mechanical Data Case: PowerDI 5 · · Moisture Sensitivity: Level 1 per J-STD-020C Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 E2 E L1 Maximum Ratings 1.05 1.15 0.33 0.43 b1 0.80 0.99 b2 1.70 1.88 D 3.90 4.05 3.05 NOM 6.40 BOTTOMSIDE HEAT SINK 6.60 1.84 NOM 5.30 5.45 3.55 NOM E2 b1 b1 LEFT PIN RIGHT PIN Weight: 0.096 grams (approximate) A A2 e Polarity: See Diagram Marking: See Page 3 Max E e e3 Min E1 W Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 Dim D2 L ä · · · · · A D L 0.75 0.95 L1 0.50 0.65 W 1.20 1.50 All Dimensions in mm Note: Pins Left & Right must be electrically connected at the printed circuit board. @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also figure 5) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Symbol Value Unit VRRM VRWM VR 100 V VR(RMS) 71 V IO 5 A IFSM 250 A Thermal Characteristics Symbol Typ Max Unit Thermal Resistance Junction to Soldering Point Characteristic RqJS ¾ 2.0 °C/W Thermal Resistance Junction to Ambient Air (Note 2) TA = 25°C RqJA 85 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 3) TA = 25°C RqJA 70 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 4) TA = 25°C RqJA 45 ¾ °C/W Tj -65 to +175 °C TSTG -65 to +175 °C Operating Temperature Range Storage Temperature Range Notes: 1. 2. 3. 4. RoHS revision 13.2.2003. High Temperature Solder Exemption Applied, see EU Directive Annex Note 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 4 www.diodes.com PDS5100H ã Diodes Incorporated Electrical Characteristics @ TA = 25°C unless otherwise specified Characteristic Symbol Min Typ Max Unit Test Condition V(BR)R 100 ¾ ¾ V IR = 3.5mA Forward Voltage VF ¾ ¾ ¾ ¾ 0.67 0.55 0.75 0.62 0.71 0.58 0.80 0.66 V IF = 5A, TS = 25°C IF = 5A, TS = 125°C IF = 10A, TS = 25°C IF = 10A, TS = 125°C Reverse Leakage Current (Note 5) IR ¾ ¾ 0.3 0.5 3.5 4.5 mA mA Reverse Breakdown Voltage (Note 5) 5. Short duration test pulse used to minimize self-heating effect. 100 IR, INSTANTANEOUS REVERSE CURRENT (A) IF, INSTANTANEOUS FORWARD CURRENT (A) Notes: 10 Tj = +175°C 1 Tj = +125°C 100m Tj = +85°C 10m Tj = +25°C 1m Tj = -65°C 0.1 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Tj = +25°C 100n 10n 1n Tj = -65°C 1.0 0 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 1 Typical Forward Characteristics 20 60 40 80 100 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 10m 800 Tj = +175°C 700 CT, TOTAL CAPACITANCE (pF) IR, INSTANTANEOUS REVERSE CURRENT (A) TS = 25°C, VR = 100V TS = 125°C, VR = 100V 1m Tj = +125°C Tj = +85°C f = 1MHz 600 500 400 300 200 100 0 0 20 40 60 80 100 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 3 Typical Reverse Characteristics DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 2 of 4 www.diodes.com 0 5 10 15 20 25 30 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Total Capacitance vs. Reverse Voltage PDS5100H 4 PF(AV), AVERAGE FORWARD POWER DISSIPATION (W) IF, DC FORWARD CURRENT (A) 7.5 6.0 4.5 Note 4 3.0 Note 2 1.5 0 0 50 25 75 100 125 150 IPK = 1 (DC) IAV 3 2 1 0 175 0 TA, AMBIENT TEMPERATURE (°C) Fig. 5 DC Forward Current Derating 1 2 3 4 5 6 7 8 9 10 IF(AV), AVERAGE FORWARD CURRENT (A) Fig. 6 Forward Power Dissipation TA, DERATED AMBIENT TEMPERATURE (°C) 200 Note 2 180 160 140 120 100 80 60 40 20 0 0 25 50 75 100 VR, DC REVERSE VOLTAGE (V) Fig. 7 Operating Temperature Derating Ordering Information Notes: 2. 3. 4. 5. 6. (Note 6) Device Packaging Shipping PDS5100H-13 PowerDIä5 5000/Tape & Reel FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. Short duration test pulse used to minimize self-heating effect. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information S5100H YYWWK S5100H = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last two digits of year ex: 04 for 2004 WW = Week code 01 to 52 K = Factory Designator DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 4 www.diodes.com PDS5100H IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 4 of 4 www.diodes.com PDS5100H