SPICE MODEL: PDR5G PDR5G 5A GLASS PASSIVATED RECTIFIER PowerDI ä5 NEW PRODUCT Features · · · · · Glass Passivated Die Construction A D Low Leakage Current A2 b2 PowerDIä5 L1 Lead Free Finish, RoHS Compliant (Note 1) "Green" Molding Compound (No Br, Sb) E Qualified to AEC-Q101 Standards for High Reliability L1 e Mechanical Data · · A2 b1 b1 D D2 b2 Case: PowerDIä5 · · Moisture Sensitivity: Level 1 per J-STD-020C · · · Polarity: See Diagram Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 E2 E 1.15 0.33 0.43 b1 0.80 0.99 b2 1.70 1.88 D 3.90 4.05 3.05 NOM 6.40 b1 BOTTOMSIDE HEAT SINK 6.60 1.84 NOM 5.30 5.45 3.55 NOM E2 Marking: See Page 3 L 0.75 0.95 L1 0.50 0.65 W 1.20 1.50 All Dimensions in mm Note: Pins Left & Right must be electrically connected at the printed circuit board. Maximum Ratings 1.05 e e LEFT PIN RIGHT PIN A A2 E L1 e3 Weight: 0.096 grams (approximate) Max E1 W b1 Min D2 L Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Dim E1 @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also figure 4) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Operating Temperature Range Storage Temperature Range Thermal Characteristics Symbol Value Unit VRRM VRWM VR 400 V VR(RMS) 283 V IO 5 A IFSM 100 A Tj -65 to +150 °C TSTG -65 to +150 °C @ TA = 25°C unless otherwise specified Characteristic Thermal Resistance Junction to Soldering Point Symbol Typ Max Unit RqJS ¾ 1.5 °C/W Thermal Resistance Junction to Ambient Air (Note 2) RqJA 75 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 3) RqJA 65 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 4) RqJA 45 ¾ °C/W Notes: 1. 2. 3. 4. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. DS30552 Rev. 5 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDR5G ã Diodes Incorporated @ TA = 25°C unless otherwise specified Symbol Min Typ Max Unit V(BR)R 400 ¾ ¾ V IR = 10mA VF ¾ 0.92 1.15 V IF = 5A, TS = 25°C Reverse Leakage Current (Note 5) IR ¾ ¾ 0.02 9 10 250 mA TS = 25°C, VR = 400V TS = 125°C, VR = 400V Reverse Recovery Time trr ¾ 3.3 ¾ ms IF = 0.5A, IR = 1.0A, Irr = 0.25A Characteristic Reverse Breakdown Voltage (Note 5) Forward Voltage 2. 3. 4. 5. 6. Test Condition FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. Short duration test pulse used to minimize self-heating effect. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 18.8mm x 14.4mm. Anode pad dimensions 5.6mm x 3.0mm. IR, INSTANTANEOUS REVERSE CURRENT (A) IF, INSTANTANEOUS FORWARD CURRENT (A) Notes: 100 10 1 Tj = 150°C 100m Tj = 85°C 10m Tj = 25°C 1m Tj = -65°C 0 0.2 0.4 0.6 0.8 1.0 Tj = +150°C Tj = +125°C Tj = +85°C 100n Tj = +25°C 10n Tj = -65°C 1n 160 80 0 1.2 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 1 Typical Forward Characteristics 240 400 320 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 7.5 100 IF, DC FORWARD CURRENT (A) f = 1 MHz CT, TOTAL CAPACITANCE (pF) NEW PRODUCT Electrical Characteristics 75 50 25 0 0 5 10 15 20 25 30 6.0 4.5 Note 6 3.0 1.5 0 VR, REVERSE VOLTAGE (V) Fig. 3 Typical Total Capacitance vs. Reverse Voltage DS30552 Rev. 5 - 2 PowerDI is a trademark of Diodes Incorporated. Note 2 2 of 3 www.diodes.com 0 25 50 75 100 125 150 175 TA, AMBIENT TEMPERATURE (°C) Fig. 4 DC Forward Current Derating PDR5G 180 TA, DERATED AMBIENT TEMPERATURE (°C) PF, FORWARD POWER DISSIPATION (W) NEW PRODUCT 4 IPK = 1 (DC) IAV 3 2 1 150 120 0 90 60 30 0 0 2 1 3 4 0 5 Ordering Information Notes: 100 200 300 400 VR, DC REVERSE VOLTAGE (V) Fig. 6 Operating Temperature Derating IF, FORWARD CURRENT (A) Fig. 5 Forward Power Dissipation (Note 7) Device Packaging Shipping PDR5G-13 PowerDIä5 5000/Tape & Reel 7. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information R5G YYWWK R5G = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last two digits of year ex: 05 for 2005 WW = Week code 01 to 52 K = Factory Designator DS30552 Rev. 5 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDR5G