PDR5G 5A GLASS PASSIVATED RECTIFIER PowerDI ä5 Features · · · · · Glass Passivated Die Construction A D Low Leakage Current A2 b2 L1 Lead Free Finish, RoHS Compliant (Note 1) PowerDIä5 "Green" Molding Compound (No Br, Sb) E E1 Qualified to AEC-Q101 Standards for High Reliability L1 e Mechanical Data · · A2 b1 b1 D D2 b2 ä Case: PowerDI 5 · · Moisture Sensitivity: Level 1 per J-STD-020C · · · Polarity: See Diagram Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 E2 LEFT PIN RIGHT PIN E 1.15 0.33 0.43 b1 0.80 0.99 b2 1.70 1.88 D 3.90 4.05 3.05 NOM 6.40 b1 BOTTOMSIDE HEAT SINK 6.60 1.84 NOM 5.30 5.45 3.55 NOM E2 L 0.75 0.95 L1 0.50 0.65 W 1.20 1.50 All Dimensions in mm Note: Pins Left & Right must be electrically connected at the printed circuit board. Maximum Ratings 1.05 e e Weight: 0.096 grams (approximate) A A2 E L1 e3 Marking: See Page 3 Max E1 W b1 Min D2 L Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Dim @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also figure 4) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Symbol Value Unit VRRM VRWM VR 400 V VR(RMS) 283 V IO 5 A IFSM 100 A Thermal Characteristics Characteristic Symbol Typ Max Unit Thermal Resistance Junction to Soldering Point RqJS ¾ 1.5 °C/W Thermal Resistance Junction to Ambient Air (Note 2) RqJA 75 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 3) RqJA 65 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 4) RqJA 45 ¾ °C/W Tj ¾ -65 to +150 °C TSTG ¾ -65 to +150 °C Operating Temperature Range Storage Temperature Range Notes: 1. 2. 3. 4. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. TA = 25°C DS30552 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDR5G ã Diodes Incorporated Electrical Characteristics @ TA = 25°C unless otherwise specified Symbol Min Typ Max Unit V(BR)R 400 ¾ ¾ V IR = 10mA VF ¾ 0.92 1.15 V IF = 5A, TS = 25°C Reverse Leakage Current (Note 5) IR ¾ ¾ 0.02 9 10 250 mA TS = 25°C, VR = 400V TS = 125°C, VR = 400V Reverse Recovery Time trr ¾ 3.3 ¾ ms IF = 0.5A, IR = 1.0A, Irr = 0.25A Characteristic Reverse Breakdown Voltage (Note 5) Forward Voltage 2. 3. 4. 5. 6. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. TA = 25°C Short duration test pulse used to minimize self-heating effect. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 18.8mm x 14.4mm. Anode pad dimensions 5.6mm x 3.0mm. IR, INSTANTANEOUS REVERSE CURRENT (A) IF, INSTANTANEOUS FORWARD CURRENT (A) Notes: Test Condition 100 10 1 Tj = 150°C 100m Tj = 85°C 10m Tj = 25°C 1m Tj = -65°C 0 0.2 0.4 0.6 0.8 1.0 Tj = +150°C Tj = +125°C Tj = +85°C 100n Tj = +25°C 10n Tj = -65°C 1n VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 1 Typical Forward Characteristics 160 80 0 1.2 240 400 320 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 7.5 100 IF, DC FORWARD CURRENT (A) CT, TOTAL CAPACITANCE (pF) f = 1 MHz 75 50 25 0 0 5 10 15 20 25 30 6.0 4.5 Note 6 3.0 1.5 0 VR, REVERSE VOLTAGE (V) Fig. 3 Typical Total Capacitance vs. Reverse Voltage DS30552 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. Note 2 2 of 3 www.diodes.com 0 25 50 75 100 125 150 175 TA, AMBIENT TEMPERATURE (°C) Fig. 4 DC Forward Current Derating PDR5G 180 TA, DERATED AMBIENT TEMPERATURE (°C) PF, FORWARD POWER DISSIPATION (W) 4 IPK = 1 (DC) IAV 3 2 1 150 120 90 60 30 0 0 0 2 1 3 0 5 4 Ordering Information Notes: 100 200 300 400 VR, DC REVERSE VOLTAGE (V) Fig. 6 Operating Temperature Derating IF, FORWARD CURRENT (A) Fig. 5 Forward Power Dissipation (Note 7) Device Packaging Shipping PDR5G-13 PowerDIä5 5000/Tape & Reel 7. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information R5G YYWWK R5G = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last two digits of year ex: 05 for 2005 WW = Week code 01 to 52 K = Factory Designator IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. DS30552 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDR5G