FINAL Advanced Micro Devices Am27C64 64 Kilobit (8,192 x 8-Bit) CMOS EPROM DISTINCTIVE CHARACTERISTICS ■ Fast access time ■ Latch-up protected to 100 mA from –1 V to VCC + 1 V — 45 ns ■ High noise immunity ■ Low power consumption — 20 µA typical CMOS standby current ■ Versatile features for simple interfacing — Both CMOS and TTL input/output compatibility ■ JEDEC-approved pinout ■ Single +5 V power supply ■ ±10% power supply tolerance available ■ 100% FlashriteTM programming — Two line control functions ■ Standard 28-pin DIP, PDIP, and 32-pin PLCC packages — Typical programming time of 1 second GENERAL DESCRIPTION The Am27C64 is a 64-Kbit ultraviolet erasable programmable read-only memory. It is organized as 8K words by 8 bits per word, operates from a single +5 V supply, has a static standby mode, and features fast single address location programming. Products are available in windowed ceramic DIP packages as well as plastic one time programmable (OTP) PDIP, and PLCC packages. Typically, any byte can be accessed in less than 45 ns, allowing operation with high-performance microprocessors without any WAIT states. The Am27C64 offers separate Output Enable (OE) and Chip Enable (CE) controls, thus eliminating bus contention in a multiple bus microprocessor system. AMD’s CMOS process technology provides high speed, low power, and high noise immunity. Typical power consumption is only 80 mW in active mode, and 100 µW in standby mode. All signals are TTL levels, including programming signals. Bit locations may be programmed singly, in blocks, or at random. The Am27C64 supports AMD’s Flashrite programming algorithm (100 µs pulses) resulting in a typical programming time of 1 second. BLOCK DIAGRAM VCC Data Outputs DQ0–DQ7 VSS VPP OE CE PGM A0–A12 Address Inputs Output Enable Chip Enable and Prog Logic Output Buffers Y Decoder Y Gating X Decoder 65,538 Bit Cell Matrix 11419D-1 2-10 Publication# 11419 Rev. D Issue Date: May 1995 Amendment /0 AMD PRODUCT SELECTOR GUIDE Family Part No. Am27C64 Ordering Part No: VCC ± 5% -255 VCC ± 10% -45 -55 -70 -90 -120 -150 -200 Max Access Time (ns) 45 55 70 90 120 150 200 250 CE (E) Access Time (ns) 45 55 70 90 120 150 200 250 OE (G) Access Time (ns) 30 35 40 40 50 50 50 50 CONNECTION DIAGRAMS Top View DIP 2 27 PGM (P) A7 3 26 NC A6 4 25 A8 A5 5 24 A9 NC A12 PGM (P) VCC DU VCC 28 VPP 1 A7 A12 VPP PLCC 4 3 2 1 32 31 30 A6 5 29 A8 A5 6 28 A9 A4 6 23 A11 A3 7 22 OE (G) A2 8 21 A10 A1 9 20 CE (E) A0 10 19 DQ7 DQ0 11 18 DQ6 DQ1 12 17 DQ5 DQ0 13 DQ2 13 16 DQ4 VSS 14 15 DQ3 A4 7 27 A11 A3 8 26 NC A2 9 25 OE (G) A1 10 24 A10 A0 11 12 23 22 CE (E) NC 21 DQ6 DQ7 DQ4 DQ5 DU DQ3 11419D-2 VSS DQ1 DQ2 14 15 16 17 18 19 20 11419D-3 Notes: 1. JEDEC nomenclature is in parentheses. LOGIC SYMBOL PIN DESIGNATIONS A0–A12 = Address Inputs CE (E) = Chip Enable DQ0–DQ7 = Data Inputs/Outputs OE (G) = Output Enable Input PGM (P) = Program Enable Input VCC = VCC Supply Voltage CE (E) VPP = Program Voltage Input PGM (P) VSS = Ground OE (G) NC = No Internal Connection DU = No External Connection (Don’t Use) 13 A0–A12 8 DQ0–DQ7 Am27C64 11419D-4 2-11 AMD ORDERING INFORMATION UV EPROM Products AMD Standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of: AM27C64 -45 D C B OPTIONAL PROCESSING Blank = Standard Processing B = Burn-in TEMPERATURE RANGE C = Commercial (0°C to +70°C) I = Industrial (–40°C to +85°C) E = Extended Commercial (–55°C to +125°C) PACKAGE TYPE D = 28-Pin Ceramic DIP (CDV028) SPEED OPTION See Product Selector Guide and Valid Combinations DEVICE NUMBER Am27C64 64 Kilobit (8,192 x 8-Bit) CMOS UV EPROM Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations. Valid Combinations AM27C64-45 DC, DCB, DI, DIB AM27C64-55 AM27C64-70 AM27C64-90 DC, DCB, DI, AM27C64-120 DIB, DE, DEB AM27C64-150 AM27C64-200 DC, DCB, DI, DIB AM27C64-255 2-12 Am27C64 AMD ORDERING INFORMATION OTP Products AMD Standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of: AM27C64 -55 P C OPTIONAL PROCESSING Blank = Standard Processing TEMPERATURE RANGE C = Commercial (0°C to +70°C) I = Industrial (–40°C to + 85°C) E = Extended Commercial (–55°C to +125°C) PACKAGE TYPE P = 28-Pin Plastic DIP (PD 028) J = 32-Pin Rectangular Plastic Leaded Chip Carrier (PL 032) SPEED OPTION See Product Selector Guide and Valid Combinations DEVICE NUMBER Am27C64 64 Kilobit (8,192 x 8-Bit) CMOS OTP EPROM Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combination. Valid Combinations AM27C64-55 AM27C64-70 AM27C64-90 AM27C64-120 AM27C64-150 AM27C64-200 AM27C64-255 JC, PC, JI, PI Am27C64 2-13 AMD FUNCTIONAL DESCRIPTION Erasing the Am27C64 In order to clear all locations of their programmed contents, it is necessary to expose the Am27C64 to an ultraviolet light source. A dosage of 15 W seconds/cm2 is required to completely erase an Am27C64. This dosage can be obtained by exposure to an ultraviolet lamp— wavelength of 2537 A° —with intensity of 12,000 µW/cm2 for 15 to 20 minutes. The Am27C64 should be directly under and about one inch from the source and all filters should be removed from the UV light source prior to erasure. It is important to note that the Am27C64 and similar devices will erase with light sources having wavelengths shorter than 4000 A° . Although erasure times will be much longer than with UV sources at 2537 A° , exposure to fluorescent light and sunlight will eventually erase the Am27C64 and exposure to them should be prevented to realize maximum system reliability. If used in such an environment, the package window should be covered by an opaque label or substance. Programming the Am27C64 Upon delivery or after each erasure the Am27C64 has all 65,536 bits in the “ONE” or HIGH state. “ZEROs” are loaded into the Am27C64 through the procedure of programming. The programming mode is entered when 12.75 V ± 0.25 V is applied to the VPP pin, CE is at VIL and PGM is at VIL. For programming, the data to be programmed is applied 8 bits in parallel to the data output pins. The Flashrite algorithm reduces programming time by using 100 µs programming pulses and by giving each address only as many pulses as is necessary in order to reliably program the data. After each pulse is applied to a given address, the data in that address is verified. If the data does not verify, additional pulses are given until it verifies or the maximum is reached. This process is repeated while sequencing through each address of the Am27C64. This part of the algorithm is done at VCC = 6.25 V to assure that each EPROM bit is programmed to a sufficiently high threshold voltage. After the final address is completed, the entire EPROM memory is verified at VCC = VPP = 5.25 V. Please refer to Section 6 for programming flow chart and characteristics. Program Inhibit Programming of multiple Am27C64 in parallel with different data is also easily accomplished. Except for CE, all like inputs of the parallel Am27C64 may be common. A TTL low-level program pulse applied to an Am27C64 2-14 PGM input with VPP = 12.75 V ± 0.25 V and CE Low will program that Am27C64. A high-level CE input inhibits the other Am27C64 devices from being programmed. Program Verify A verify should be performed on the programmed bits to determine that they were correctly programmed. The verify should be performed with OE and CE at VIL , PGM at VIH, and VPP between 12.5 V and 13.0 V. Auto Select Mode The auto select mode allows the reading out of a binary code from an EPROM that will identify its manufacturer and type. This mode is intended for use by programming equipment for the purpose of automatically matching the device to be programmed with its corresponding programming algorithm. This mode is functional in the 25°C ± 5°C ambient temperature range that is required when programming the Am27C64. To activate this mode, the programming equipment must force 12.0 V ± 0.5 V on address line A9 of the Am27C64. Two identifier bytes may then be sequenced from the device outputs by toggling address line A0 from VIL to VIH. All other address lines must be held at VIL during auto select mode. Byte 0 (A0 = VIL) represents the manufacturer code, and byte 1 (A0 = VIH), the device code. For the Am27C64, these two identifier bytes are given in the Mode Select Table. All identifiers for manufacturer and device codes will possess odd parity, with the MSB (DQ7) defined as the parity bit. Read Mode The Am27C64 has two control functions, both of which must be logically satisfied in order to obtain data at the outputs. Chip Enable (CE) is the power control and should be used for device selection. Output Enable (OE) is the output control and should be used to gate data to the output pins, independent of device selection. Assuming that addresses are stable, address access time (tACC) is equal to the delay from CE to output (tCE). Data is available at the outputs tOE after the falling edge of OE, assuming that CE has been LOW and addresses have been stable for at least tACC–tOE. Standby Mode The Am27C64 has a CMOS standby mode which reduces the maximum VCC current to 100 µA. It is placed in CMOS-standby when CE is at VCC ± 0.3 V. The Am27C64 also has a TTL-standby mode which reduces the maximum VCC current to 1.0 mA. It is placed in TTL-standby when CE is at VIH. When in standby mode, the outputs are in a high-impedance state, independent of the OE input. Am27C64 AMD Output OR-Tieing System Applications To accommodate multiple memory connections, a twoline control function is provided to allow for: During the switch between active and standby conditions, transient current peaks are produced on the rising and falling edges of Chip Enable. The magnitude of these transient current peaks is dependent on the output capacitance loading of the device. At a minimum, a 0.1-µF ceramic capacitor (high frequency, low inherent inductance) should be used on each device between VCC and VSS to minimize transient effects. In addition, to overcome the voltage drop caused by the inductive effects of the printed circuit board traces on EPROM arrays, a 4.7-µF bulk electrolytic capacitor should be used between VCC and VSS for each eight devices. The location of the capacitor should be close to where the power supply is connected to the array. ■ Low memory power dissipation ■ Assurance that output bus contention will not occur It is recommended that CE be decoded and used as the primary device-selecting function, while OE be made a common connection to all devices in the array and connected to the READ line from the system control bus. This assures that all deselected memory devices are in low-power standby mode and that the output pins are only active when data is desired from a particular memory device. MODE SELECT TABLE Pins CE OE PGM A0 A9 VPP Outputs VIL VIL X X X X DOUT Output Disable X VIH X X X X High-Z Standby (TTL) VIH X X X X X High-Z VCC ± 0.3 V X X X X X High-Z Program VIL X VIL X X VPP DIN Program Verify VIL VIL VIH X X VPP DOUT Program Inhibit VIH X X X X VPP High-Z Manufacturer Code VIL VIL X VIL VH X 01H Device Code VIL VIL X VIH VH X 15H Mode Read Standby (CMOS) Auto Select (Note 3) Notes: 1. VH = 12.0 V ± 0.5 V 2. X = Either VIH or VIL 3. A1–A8 = A10–A12 = VIL 4. See DC Programming Characteristics for VPP voltage during programming. Am27C64 2-15 AMD ABSOLUTE MAXIMUM RATINGS OPERATING RANGES Storage Temperature OTP Products . . . . . . . . . . . . . . . –65°C to +125°C All Other Products . . . . . . . . . . . . –65°C to +150°C Commercial (C) Devices Ambient Temperature (TA) . . . . . . . 0°C to +70°C Ambient Temperature with Power Applied . . . . . . . . . . . . . –55°C to +125°C Voltage with Respect To VSS All pins except A9,VPP,VCC . –0.6 V to VCC + 0.5 V A9 and VPP . . . . . . . . . . . . . . . . –0.6 V to +13.5 V Industrial (I) Devices Ambient Temperature (TA) . . . . . –40°C to +85°C Extended Commercial (E) Devices Ambient Temperature (TA) . . . . –55°C to +125°C Supply Read Voltages VCC for Am27C64-XX5 . . . . . . +4.75 V to +5.25 V VCC . . . . . . . . . . . . . . . . . . . . . . . –0.6 V to +7.0 V VCC for Am27C64-XX0 . . . . . . +4.50 V to +5.50 V Notes: 1. Minimum DC voltage on input or I/O pins is –0.5 V. During transitions, the inputs may overshoot VSS to –2.0 V for periods of up to 20 ns. Maximum DC voltage on input and I/O pins is VCC + 0.5 V which may overshoot to VCC + 2.0 V for periods up to 20 ns. Operating ranges define those limits between which the functionality of the device is guaranteed. 2. For A9 and VPP the minimum DC input is –0.5 V. During transitions, A9 and VPP may overshoot VSS to –2.0 V for periods of up to 20 ns. A9 and VPP must not exceed 13.5 V for any period of time. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. 2-16 Am27C64 AMD DC CHARACTERISTICS over operating range unless otherwise specified. (Notes 1, 2, 3 and 4) Parameter Symbol Parameter Description Test Conditions Min VOH Output HIGH Voltage IOH = –400 µA 2.4 VOL Output LOW Voltage IOL = 2.1 mA VIH Input HIGH Voltage VIL Input LOW Voltage ILI Input Load Current VIN = 0 V to VCC ILO Output Leakage Current VOUT = 0 V to VCC Max Unit V 0.45 V 2.0 VCC + 0.5 V –0.5 +0.8 V 1.0 µA C/I Devices 1.0 E Devices 5.0 µA ICC1 VCC Active Current (Note 3) CE = VIL, f = 10 MHz, IOUT = 0 mA 25 mA ICC2 VCC TTL Standby Current CE = VIH 1 mA ICC3 VCC CMOS Standby Current CE = VCC ± 0.3 V 100 µA IPP1 VPP Current During Read CE = OE = VIL, VPP = VCC 100 µA Notes: 1. VCC must be applied simultaneously or before VPP, and removed simultaneously or after VPP. 2. Caution: The Am27C64 must not be removed from (or inserted into) a socket when VCC or VPP is applied. 3. ICC1 is tested with OE = VIH to simulate open outputs. 30 30 25 25 Supply Current in mA Supply Current in mA 4. Minimum DC Input Voltage is –0.5 V. During transitions, the inputs may overshoot to –2.0 V for periods less than 20 ns. Maximum DC Voltage on output pins is VCC + 0.5 V, which may overshoot to VCC + 2.0 V for periods less than 20 ns. 20 15 10 1 2 3 4 5 6 7 8 9 10 20 15 10 –75 –50 –25 0 25 50 75 100 125 150 Temperature in °C Frequency in MHz Figure 1. Typical Supply Current vs. Frequency VCC = 5.5 V, T = 25°C Figure 2. Typical Supply Current vs. Temperature VCC = 5.5 V, f = 10 MHz 11419D-5 Am27C64 11419D-6 2-17 AMD CAPACITANCE Parameter Symbol Parameter Description CDV028 Test Conditions PL 032 PD 028 Typ Max Typ Max Typ Max Unit CIN Input Capacitance VIN = 0 8 10 6 10 5 10 pF COUT Output Capacitance VOUT = 0 11 14 8 12 8 10 pF Notes: 1. This parameter is only sampled and not 100% tested. 2. TA = +25°C, f = 1 MHz. SWITCHING CHARACTERISTICS over operating range unless otherwise specified (Notes 1, 3 and 4) Parameter Symbols JEDEC Am27C64 Parameter Standard Description Test Conditions -45 -55 -70 -90 -120 -150 -200 -255 Unit tAVQV tACC Address to Output Delay CE = OE = VIL Min Max – 45 – 55 – 70 – 90 – 120 – 150 – 200 – 250 ns tELQV tCE Chip Enable to Output Delay OE = VIL Min Max – 45 – 55 – 70 – 90 – 120 – 150 – 200 – 250 ns Output Enable to Output Delay CE = VIL Min Max – 30 – 35 – 40 – 40 – 50 – 50 – 50 – 50 ns Chip Enable HIGH or Output Enable HIGH, whichever comes first, to Output Float Min Max – 25 – 25 – 25 – 25 – 30 – 30 – 30 – 30 ns Output Hold from Addresses, CE, or OE, whichever occurred first Min Max 0 – 0 – 0 – 0 – 0 – 0 – 0 – 0 – ns tGLQV tOE tEHQZ tGHQZ tDF (Note 2) tAXQX tOH Notes: 1. VCC must be applied simultaneously or before VPP, and removed simultaneously or after VPP. 2. This parameter is only sampled and not 100% tested. 3. Caution: The Am27C64 must not be removed from (or inserted into) a socket or board when VPP or VCC is applied. 4. For the -45, -55 and -70: Output Load: 1 TTL gate and CL = 30 pF Input Rise and Fall Times: 20 ns Input Pulse Levels: 0 V to 3 V Timing Measurement Reference Level: 1.5 V for inputs and outputs For all other versions: Output Load: 1 TTL gate and CL = 100 pF Input Rise and Fall Times: 20 ns Input Pulse Levels: 0.45 V to 2.4 V Timing Measurement Reference Level: 0.8 V and 2 V inputs and outputs 2-18 Am27C64 AMD SWITCHING TEST CIRCUIT 2.7 kΩ Device Under Test +5.0 V CL Diodes = IN3064 or Equivalent 6.2 kΩ CL = 100 pF including jig capacitance (30 pF for -45, -55, -70) 11419D-7 SWITCHING TEST WAVEFORM 2.4 V 2.0 V 0.8 V Test Points 3V 2.0 V 0.8 V 1.5 V 0.45 V Test Points 1.5 V 0V Input Output Input Output 11419D-8 AC Testing: Inputs are driven at 3.0 V for a logic “1” and 0 V for a logic “0”. Input pulse rise and fall times are ≤ 20 ns for -45, -55 and -70. AC Testing: Inputs are driven at 2.4 V for a logic “1” and 0.45 V for a logic “0”. Input pulse rise and fall times are ≤ 20 ns. Am27C64 2-19 AMD KEY TO SWITCHING WAVEFORMS WAVEFORM INPUTS OUTPUTS Must Be Steady Will Be Steady May Change from H to L Will Be Changing from H to L May Change from L to H Will Be Changing from L to H Don’t Care, Any Change Permitted Changing State Unknown Does Not Apply Center Line is High Impedence “Off” State KS000010 SWITCHING WAVEFORMS 2.4 Addresses 0.45 2.0 0.8 2.0 0.8 Addresses Valid CE tCE OE Output High Z tACC (Note 1) tOE tOH Valid Output tDF (Note 2) High Z Notes: 1. OE may be delayed up to tACC–tOE after the falling edge of the addresses without impact on tACC. 2. tDF is specified from OE or CE, whichever occurs first. 2-20 Am27C64 11419D-9