SN54/74LS160A SN54/74LS161A SN54/74LS162A SN54/74LS163A BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS The LS160A / 161A / 162A / 163A are high-speed 4-bit synchronous counters. They are edge-triggered, synchronously presettable, and cascadable MSI building blocks for counting, memory addressing, frequency division and other applications. The LS160A and LS162A count modulo 10 (BCD). The LS161A and LS163A count modulo 16 (binary.) The LS160A and LS161A have an asynchronous Master Reset (Clear) input that overrides, and is independent of, the clock and all other control inputs. The LS162A and LS163A have a Synchronous Reset (Clear) input that overrides all other control inputs, but is active only during the rising clock edge. BCD (Modulo 10) Binary (Modulo 16) Asynchronous Reset LS160A LS161A Synchronous Reset LS162A LS163A • • • • • • BCD DECADE COUNTERS / 4-BIT BINARY COUNTERS LOW POWER SCHOTTKY J SUFFIX CERAMIC CASE 620-09 16 Synchronous Counting and Loading Two Count Enable Inputs for High Speed Synchronous Expansion Terminal Count Fully Decoded Edge-Triggered Operation Typical Count Rate of 35 MHz ESD > 3500 Volts 1 16 1 CONNECTION DIAGRAM DIP (TOP VIEW) VCC 16 TC Q0 Q1 Q2 Q3 CET PE 15 14 13 12 11 10 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 2 CP 3 P0 4 P1 5 P2 6 P3 1 ORDERING INFORMATION Parallel Enable (Active LOW) Input Parallel Inputs Count Enable Parallel Input Count Enable Trickle Input Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input Synchronous Reset (Active LOW) Input Parallel Outputs (Note b) Terminal Count Output (Note b) 1.0 U.L. 0.5 U.L. 0.5 U.L. 1.0 U.L. 0.5 U.L. 0.5 U.L. 1.0 U.L. 10 U.L. 10 U.L. LOW 0.5 U.L. 0.25 U.L. 0.25 U.L. 0.5 U.L. 0.25 U.L. 0.25 U.L. 0.5 U.L. 5 (2.5) U.L. 5 (2.5) U.L. NOTES: a) 1 TTL Unit Load (U.L.) = 40 µA HIGH/1.6 mA LOW. b) The Output LOW drive factor is 2.5 U.L. for Military (54) and 5 U.L. for Commercial (74) Temperature Ranges. Ceramic Plastic SOIC LOGIC SYMBOL LOADING (Note a) HIGH PE P0 – P3 CEP CET CP MR SR Q0 – Q3 TC SN54LSXXXJ SN74LSXXXN SN74LSXXXD 8 7 CEP GND PIN NAMES D SUFFIX SOIC CASE 751B-03 16 *MR for LS160A and LS161A *SR for LS162A and LS163A 1 *R N SUFFIX PLASTIC CASE 648-08 9 7 3 4 5 6 PE P0 P1 P2 P3 CEP 10 CET 2 CP TC *R Q0 Q1 Q2 Q3 1 14 13 12 11 VCC = PIN 16 GND = PIN 8 *MR for LS160A and LS161A *SR for LS162A and LS163A FAST AND LS TTL DATA 5-1 15 SN54/74LS160A • SN54/74LS161A SN54/74LS162A • SN54/74LS163A STATE DIAGRAM LS160A • LS162A LS161A • LS163A LOGIC EQUATIONS 0 4 0 15 5 15 5 14 6 14 6 13 7 13 7 8 12 12 1 11 2 10 3 9 1 2 11 3 10 9 4 8 Count Enable = CEP • CET • PE TC for LS160A & LS162A = CET • Q0 • Q1 • Q2 • Q3 TC for LS161A & LS163A = CET • Q0 • Q1 • Q2 • Q3 Preset = PE • CP + (rising clock edge) Reset = MR (LS160A & LS161A) Reset = SR • CP + (rising clock edge) Reset = (LS162A & LS163A) NOTE: The LS160A and LS162A can be preset to any state, but will not count beyond 9. If preset to state 10, 11, 12, 13, 14, or 15, it will return to its normal sequence within two clock pulses. FUNCTIONAL DESCRIPTION The LS160A / 161A / 162A / 163A are 4-bit synchronous counters with a synchronous Parallel Enable (Load) feature. The counters consist of four edge-triggered D flip-flops with the appropriate data routing networks feeding the D inputs. All changes of the Q outputs (except due to the asynchronous Master Reset in the LS160A and LS161A) occur as a result of, and synchronous with, the LOW to HIGH transition of the Clock input (CP). As long as the set-up time requirements are met, there are no special timing or activity constraints on any of the mode control or data inputs. Three control inputs — Parallel Enable (PE), Count Enable Parallel (CEP) and Count Enable Trickle (CET) — select the mode of operation as shown in the tables below. The Count Mode is enabled when the CEP, CET, and PE inputs are HIGH. When the PE is LOW, the counters will synchronously load the data from the parallel inputs into the flip-flops on the LOW to HIGH transition of the clock. Either the CEP or CET can be used to inhibit the count sequence. With the PE held HIGH, a LOW on either the CEP or CET inputs at least one set-up time prior to the LOW to HIGH clock transition will cause the existing output states to be retained. The AND feature of the two Count Enable inputs (CET • CEP) allows synchronous cascading without external gating and without delay accumulation over any practical number of bits or digits. The Terminal Count (TC) output is HIGH when the Count Enable Trickle (CET) input is HIGH while the counter is in its maximum count state (HLLH for the BCD counters, HHHH for the Binary counters). Note that TC is fully decoded and will, therefore, be HIGH only for one count state. The LS160A and LS162A count modulo 10 following a binary coded decimal (BCD) sequence. They generate a TC output when the CET input is HIGH while the counter is in state 9 (HLLH). From this state they increment to state 0 (LLLL). If loaded with a code in excess of 9 they return to their legitimate sequence within two counts, as explained in the state diagram. States 10 through 15 do not generate a TC output. The LS161A and LS163A count modulo 16 following a binary sequence. They generate a TC when the CET input is HIGH while the counter is in state 15 (HHHH). From this state they increment to state 0 (LLLL). The Master Reset (MR) of the LS160A and LS161A is asynchronous. When the MR is LOW, it overrides all other input conditions and sets the outputs LOW. The MR pin should never be left open. If not used, the MR pin should be tied through a resistor to VCC, or to a gate output which is permanently set to a HIGH logic level. The active LOW Synchronous Reset (SR) input of the LS162A and LS163A acts as an edge-triggered control input, overriding CET, CEP and PE, and resetting the four counter flip-flops on the LOW to HIGH transition of the clock. This simplifies the design from race-free logic controlled reset circuits, e.g., to reset the counter synchronously after reaching a predetermined value. MODE SELECT TABLE *SR PE CET CEP Action on the Rising Clock Edge ( L H H H H X L H H H X X H L X X X H X L RESET (Clear) LOAD (Pn → Qn) COUNT (Increment) NO CHANGE (Hold) NO CHANGE (Hold) FAST AND LS TTL DATA 5-2 ) *For the LS162A and *LS163A only. H = HIGH Voltage Level L = LOW Voltage Level X = Don’t Care SN54/74LS160A • SN54/74LS161A SN54/74LS162A • SN54/74LS163A GUARANTEED OPERATING RANGES Symbol Parameter Min Typ Max Unit VCC Supply Voltage 54 74 4.5 4.75 5.0 5.0 5.5 5.25 V TA Operating Ambient Temperature Range 54 74 – 55 0 25 25 125 70 °C IOH Output Current — High 54, 74 – 0.4 mA IOL Output Current — Low 54 74 4.0 8.0 mA LS160A and LS161A DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits S b l Symbol P Parameter VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Diode Voltage VOH Output HIGH Voltage VOL Output LOW Voltage IIH Min Typ Max U i Unit 2.0 54 0.7 74 0.8 – 0.65 – 1.5 T Test C Conditions di i V Guaranteed Input HIGH Voltage for All Inputs V Guaranteed Input p LOW Voltage g for All Inputs V VCC = MIN, IIN = – 18 mA 54 2.5 3.5 V 74 2.7 3.5 V VCC = MIN,, IOH = MAX,, VIN = VIH or VIL per Truth Table VCC = VCC MIN, VIN = VIL or VIH per Truth Table 54, 74 0.25 0.4 V IOL = 4.0 mA 74 0.35 0.5 V IOL = 8.0 mA Input HIGH Current MR, Data, CEP, Clock PE, CET 20 40 µA VCC = MAX, VIN = 2.7 V MR, Data, CEP, Clock PE, CET 0.1 0.2 mA VCC = MAX, VIN = 7.0 V – 0.4 – 0.8 mA VCC = MAX, VIN = 0.4 V – 100 mA VCC = MAX 31 32 mA VCC = MAX IIL Input LOW Current MR, Data, CEP, Clock PE, CET IOS Short Circuit Current (Note 1) ICC Power Supply Current Total, Output HIGH Total, Output LOW – 20 Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. FAST AND LS TTL DATA 5-3 SN54/74LS160A • SN54/74LS161A SN54/74LS162A • SN54/74LS163A LS162A and LS163A DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits S b l Symbol P Parameter VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Diode Voltage VOH Output HIGH Voltage VOL Output LOW Voltage IIH Min Typ Max U i Unit 2.0 54 0.7 74 0.8 – 0.65 – 1.5 T Test C Conditions di i V Guaranteed Input HIGH Voltage for All Inputs V Guaranteed Input p LOW Voltage g for All Inputs V VCC = MIN, IIN = – 18 mA 54 2.5 3.5 V 74 2.7 3.5 V VCC = MIN,, IOH = MAX,, VIN = VIH or VIL per Truth Table VCC = VCC MIN, VIN = VIL or VIH per Truth Table 54, 74 0.25 0.4 V IOL = 4.0 mA 74 0.35 0.5 V IOL = 8.0 mA Input HIGH Current Data, CEP, Clock PE, CET, SR 20 40 µA VCC = MAX, VIN = 2.7 V Data, CEP, Clock PE, CET, SR 0.1 0.2 mA VCC = MAX, VIN = 7.0 V – 0.4 – 0.8 mA VCC = MAX, VIN = 0.4 V – 100 mA VCC = MAX 31 32 mA VCC = MAX IIL Input LOW Current Data, CEP, Clock, PE, SR CET IOS Short Circuit Current (Note 1) ICC Power Supply Current Total, Output HIGH Total, Output LOW – 20 Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25°C) Limits S b l Symbol P Parameter Min Typ 25 32 Max U i Unit fMAX Maximum Clock Frequency tPLH tPHL Propagation Delay Clock to TC 20 18 35 35 ns tPLH tPHL Propagation Delay Clock to Q 13 18 24 27 ns tPLH tPHL Propagation Delay CET to TC 9.0 9.0 14 14 ns tPHL MR or SR to Q 20 28 ns FAST AND LS TTL DATA 5-4 T Test C Conditions di i MHz VCC = 5.0 50V CL = 15 pF SN54/74LS160A • SN54/74LS161A SN54/74LS162A • SN54/74LS163A AC SETUP REQUIREMENTS (TA = 25°C) Limits S b l Symbol P Parameter Min Typ Max U i Unit tWCP Clock Pulse Width Low 25 ns tW MR or SR Pulse Width 20 ns ts Setup Time, other* 20 ns ts Setup Time PE or SR 25 ns th Hold Time, data 3 ns th Hold Time, other 0 ns trec Recovery Time MR to CP 15 ns T Test C Conditions di i VCC = 5.0 50V *CEP, CET or DATA DEFINITION OF TERMS SETUP TIME (ts) — is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. nition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized. RECOVERY TIME (trec) — is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW to HIGH in order to recognize and transfer HIGH Data to the Q outputs. HOLD TIME (th) — is defined as the minimum time following the clock transition from LOW to HIGH that the logic level must be maintained at the input in order to ensure continued recog- AC WAVEFORMS tW(H) CP 1.3 V tPHL Q 1.3 V tW(L) MR 1.3 V tPLH 1.3 V tW trec OTHER CONDITIONS: PE = MR (SR) = H CEP = CET = H 1.3 V CP 1.3 V Q0 ⋅ Q1 ⋅ Q2 ⋅ Q3 Figure 1. Clock to Output Delays, Count Frequency, and Clock Pulse Width tPHL OTHER CONDITIONS: PE = L P0 = P1 = P2 = P3 = H 1.3 V Figure 2. Master Reset to Output Delay, Master Reset Pulse Width, and Master Reset Recovery Time FAST AND LS TTL DATA 5-5 SN54/74LS160A • SN54/74LS161A SN54/74LS162A • SN54/74LS163A AC WAVEFORMS (continued) COUNT ENABLE TRICKLE INPUT TO TERMINAL COUNT OUTPUT DELAYS The positive TC pulse occurs when the outputs are in the (Q0 • Q1 • Q2 • Q3) state for the LS160 and LS162 and the (Q0 • Q1 • Q2 • Q3) state for the LS161 and LS163. 1.3 V 1.3 V CET tPHL tPLH 1.3 V 1.3 V TC Figure 3 OTHER CONDITIONS: CP = PE = CEP = MR = H CLOCK TO TERMINAL COUNT DELAYS 1.3 V CP 1.3 V 1.3 V tPLH The positive TC pulse is coincident with the output state (Q0 • Q1 • Q2 • Q3) state for the LS161 and LS163 and (Q0 • Q1 • Q2 • Q3) for the LS161 and LS163. TC 1.3 V Figure 4 1.3 V OTHER CONDITIONS: PE = CEP = CET = MR = H 1.3 V CP SETUP TIME (ts) AND HOLD TIME (th) FOR PARALLEL DATA INPUTS ts(H) P0 • P1 • P2 • P3 The shaded areas indicate when the input is permitted to change for predictable output performance. tPHL 1.3 V th(H) = 0 1.3 V ts(L) 1.3 V th(L) = 0 1.3 V Q0 • Q1 • Q2 • Q3 OTHER CONDITIONS: PE = L, MR = H Figure 5 SETUP TIME (ts) AND HOLD TIME (th) FOR COUNT ENABLE (CEP) AND (CET) AND PARALLEL ENABLE (PE) INPUTS The shaded areas indicate when the input is permitted to change for predictable output performance. CP ts(L) SR or PE 1.3 V 1.3 V th (L) = 0 ts(H) 1.3 V CEP 1.3 V PARALLEL LOAD (See Fig. 5) ts(H) th(H) = 0 COUNT MODE (See Fig. 7) Q RESPONSE TO PE ts(H) COUNT OR LOAD Q RESPONSE TO SR th(H) = 0 1.3 V CET 1.3 V RESET 1.3 V 1.3 V CP ts(L) th(L) = 0 1.3 V ts(L) th(H) = 0 1.3 V COUNT 1.3 V 1.3 V HOLD Q OTHER CONDITIONS: PE = H, MR = H Figure 6 Figure 7 FAST AND LS TTL DATA 5-6 th(L) = 0 1.3 V HOLD