Am29LV320D Data Sheet July 2003 The following document specifies Spansion memory products that are now offered by both Advanced Micro Devices and Fujitsu. Although the document is marked with the name of the company that originally developed the specification, these products will be offered to customers of both AMD and Fujitsu. Continuity of Specifications There is no change to this datasheet as a result of offering the device as a Spansion product. Any changes that have been made are the result of normal datasheet improvement and are noted in the document revision summary, where supported. Future routine revisions will occur when appropriate, and changes will be noted in a revision summary. Continuity of Ordering Part Numbers AMD and Fujitsu continue to support existing part numbers beginning with “Am” and “MBM”. To order these products, please use only the Ordering Part Numbers listed in this document. For More Information Please contact your local AMD or Fujitsu sales office for additional information about Spansion memory solutions. Publication Number 23579 Revision C Amendment +6 Issue Date November 15, 2004 THIS PAGE LEFT INTENTIONALLY BLANK. Am29LV320D 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Boot Sector Flash Memory DISTINCTIVE CHARACTERISTICS ARCHITECTURAL ADVANTAGES ■ Secured Silicon (SecSi Sector) — 64 Kbyte Sector Size; Replacement/substitute devices (such as Mirrorbit™) have 256 bytes. — Factory locked and identifiable: 16 bytes (8 words) available for secure, random factory Electronic Serial Number; verifiable as factory locked through autoselect function. ExpressFlash option allows entire sector to be available for factory-secured data — Customer lockable: Can be programmed once and then permanently locked after being shipped from AMD TM ■ Zero Power Operation — Sophisticated power management circuits reduce power consumed during inactive periods to nearly zero. ■ Package options — 48-pin TSOP — 48-ball FBGA ■ Sector Architecture — Eight 8 Kbyte sectors — Sixty-three 64 Kbyte sectors ■ Top or bottom boot block ■ Manufactured on 0.23 µm process technology ■ Compatible with JEDEC standards — Pinout and software compatible with single-power-supply flash standard PERFORMANCE CHARACTERISTICS ■ High performance — Access time as fast 90 ns — Program time: 7µs/word typical utilizing Accelerate function ■ Ultra low power consumption (typical values) — 2 mA active read current at 1 MHz — 10 mA active read current at 5 MHz — 200 nA in standby or automatic sleep mode ■ Minimum 1 million erase cycles guaranteed per sector ■ 20 Year data retention at 125°C — Reliable operation for the life of the system SOFTWARE FEATURES ■ Supports Common Flash Memory Interface (CFI) ■ Erase Suspend/Erase Resume — Suspends erase operations to allow programming in non-suspended sectors ■ Data# Polling and Toggle Bits — Provides a software method of detecting the status of program or erase cycles ■ Unlock Bypass Program command — Reduces overall programming time when issuing multiple program command sequences HARDWARE FEATURES ■ Any combination of sectors can be erased ■ Ready/Busy# output (RY/BY#) — Hardware method for detecting program or erase cycle completion ■ Hardware reset pin (RESET#) — Hardware method of resetting the internal state machine to the read mode ■ WP#/ACC input pin — Write protect (WP#) function allows protection of two outermost boot sectors, regardless of sector protect status — Acceleration (ACC) function provides accelerated program times ■ Sector protection — Hardware method of locking a sector, either in-system or using programming equipment, to prevent any program or erase operation within that sector — Temporary Sector Unprotect allows changing data in protected sectors in-system Publication# 23579 Rev: C Amendment/+6 Issue Date: November 15, 2004 GENERAL DESCRIPTION T h e A m 2 9 LV 3 2 0 D i s a 3 2 m e g a b i t , 3 . 0 volt-only flash memory device, organized as 2,097,152 words of 16 bits each or 4,194,304 bytes of 8 bits each. Word mode data appears on DQ0–DQ15; byte mode data appears on DQ0–DQ7. The device is designed to be programmed in-system with the standard 3.0 volt V CC supply, and can also be programmed in standard EPROM programmers. The device is available with an access time of 90 or 120 ns. The devices are offered in 48-pin TSOP and 48-ball FBGA packages. Standard control pins—chip enable (CE#), write enable (WE#), and output enable (OE#)—control normal read and write operations, and avoid bus contention issues. The device requires only a single 3.0 volt power supply for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. Am29LV320D Features The SecSi TM Sector (Secured Silicon) is an extra sector capable of being permanently locked by AMD or customers. The SecSi Indicator Bit (DQ7) is permanently set to a 1 if the part is factory locked, and set to a 0 if customer lockable. This way, customer lockable parts can never be used to replace a factory locked part. Note that the Am29LV320D has a SecSi Sector size of 64 Kbytes. AMD devices designated as replacements or substitutes, such as the Am29LV320M, have 256 bytes. This should be considered during system design. Factory locked parts provide several options. The SecSi Sector may store a secure, random 16 byte ESN (Electronic Serial Number), cus- 4 tomer code (programmed through AMD’s ExpressFlash service), or both. Customer Lockable parts may utilize the SecSi Sector as bonus space, reading and writing like any other flash sector, or may permanently lock their own code there. The device offers complete compatibility with the JEDEC single-power-supply Flash command set standard. Commands are written to the command register using standard microprocessor write timings. Reading data out of the device is similar to reading from other Flash or EPROM devices. The host system can detect whether a program or erase operation is complete by using the device status bits: RY/BY# pin, DQ7 (Data# Polli n g ) a n d D Q 6 /D Q 2 ( t og g l e b i t s ). A f t e r a program or erase cycle is completed, the device automatically returns to the read mode. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other s e c to rs . T h e d e v i c e i s fu l l y e ra s e d w h en shipped from the factory. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of the sectors of memory. This can be achieved in-system or via programming equipment. The device offers two power-saving features. When addresses are stable for a specified amount of time, the device enters the automatic sleep mode. The system can also place the device into the standby mode. Power consumption is greatly reduced in both modes. Am29LV320D November 15, 2004 TABLE OF CONTENTS Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 6 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . 7 Special Package Handling Instructions .................................... 8 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Ordering Information . . . . . . . . . . . . . . . . . . . . . . 10 Device Bus Operations . . . . . . . . . . . . . . . . . . . . . 11 Table 1. Am29LV320D Device Bus Operations ..............................11 Word/Byte Configuration ........................................................ 11 Requirements for Reading Array Data ................................... 11 Writing Commands/Command Sequences ............................ 12 Accelerated Program Operation .......................................... 12 Autoselect Functions ........................................................... 12 Standby Mode ........................................................................ 12 Automatic Sleep Mode ........................................................... 13 RESET#: Hardware Reset Pin ............................................... 13 Output Disable Mode .............................................................. 13 Table 2. Top Boot Sector Addresses (Am29LV320DT) ..................13 Table 3. Top Boot SecSiTM Sector Addresses................................ 14 Table 4. Bottom Boot Sector Addresses (Am29LV320DB) .............15 Table 5. Bottom Boot SecSiTM Sector Addresses .......................... 16 Autoselect Mode ..................................................................... 16 Table 6. Autoselect Codes (High Voltage Method) ........................16 Sector/Sector Block Protection and Unprotection .................. 17 Table 7. Top Boot Sector/Sector Block Addresses for Protection/Unprotection .............................................................17 Table 8. Bottom Boot Sector/Sector Block Addresses for Protection/Unprotection ...........................................17 Write Protect (WP#) ................................................................ 18 Temporary Sector Unprotect .................................................. 18 Figure 1. Temporary Sector Unprotect Operation........................... 18 Figure 2. In-System Sector Protect/Unprotect Algorithms .............. 19 SecSiTM Sector (Secured Silicon) Flash Memory Region ....... 20 Factory Locked: SecSi Sector Programmed and Protected at the Factory ............................................... 20 Customer Lockable: SecSi Sector NOT Programmed or Protected at the Factory .................................................. 20 Figure 3. SecSi Sector Protect Verify.............................................. 21 Hardware Data Protection ...................................................... 21 Low VCC Write Inhibit ......................................................... 21 Write Pulse “Glitch” Protection ............................................ 21 Logical Inhibit ...................................................................... 21 Power-Up Write Inhibit ......................................................... 21 Common Flash Memory Interface (CFI) . . . . . . . 21 Table 9. CFI Query Identification String .......................................... 22 Table 10. System Interface String................................................... 22 Table 11. Device Geometry Definition ............................................ 23 Table 12. Primary Vendor-Specific Extended Query ...................... 24 Command Definitions . . . . . . . . . . . . . . . . . . . . . . 25 Reading Array Data ................................................................ 25 Reset Command ..................................................................... 25 Autoselect Command Sequence ............................................ 25 Table 13. Autoselect Codes ............................................................25 Enter SecSiTM Sector/Exit SecSi Sector Command Sequence .............................................................. 26 Byte/Word Program Command Sequence ............................. 26 Unlock Bypass Command Sequence .................................. 26 November 15, 2004 Figure 4. Program Operation ......................................................... 27 Chip Erase Command Sequence ........................................... 27 Sector Erase Command Sequence ........................................ 27 Erase Suspend/Erase Resume Commands ........................... 28 Figure 5. Erase Operation.............................................................. 28 Command Definitions ............................................................. 29 Table 14. Am29LV320D Command Definitions ............................. 29 Write Operation Status . . . . . . . . . . . . . . . . . . . . 30 DQ7: Data# Polling ................................................................. 30 Figure 6. Data# Polling Algorithm .................................................. 30 RY/BY#: Ready/Busy# ............................................................ 31 DQ6: Toggle Bit I .................................................................... 31 Figure 7. Toggle Bit Algorithm........................................................ 31 DQ2: Toggle Bit II ................................................................... 32 Reading Toggle Bits DQ6/DQ2 ............................................... 32 DQ5: Exceeded Timing Limits ................................................ 32 DQ3: Sector Erase Timer ....................................................... 32 Table 15. Write Operation Status ................................................... 33 Absolute Maximum Ratings . . . . . . . . . . . . . . . . 34 Figure 8. Maximum Negative Overshoot Waveform ...................... 34 Figure 9. Maximum Positive Overshoot Waveform........................ 34 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . 34 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 35 Figure 10. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) ............................................................. 36 Figure 11. Typical ICC1 vs. Frequency ............................................ 36 Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Figure 12. Test Setup.................................................................... 37 Table 16. Test Specifications ......................................................... 37 Figure 13. Input Waveforms and Measurement Levels ................. 37 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 14. Read Operation Timings ............................................... 38 Figure 15. Reset Timings ............................................................... 39 Word/Byte Configuration (BYTE#) ............................................. 40 Figure 16. BYTE# Timings for Read Operations............................ 40 Figure 17. BYTE# Timings for Write Operations............................ 40 Erase and Program Operations ................................................. 41 Figure 18. Program Operation Timings.......................................... Figure 19. Chip/Sector Erase Operation Timings .......................... Figure 20. Data# Polling Timings (During Embedded Algorithms). Figure 21. Toggle Bit Timings (During Embedded Algorithms)...... Figure 22. DQ2 vs. DQ6................................................................. 42 43 44 45 45 Temporary Sector Unprotect ..................................................... 46 Figure 23. Temporary Sector Unprotect Timing Diagram .............. 46 Figure 24. Accelerated Program Timing Diagram.......................... 46 Figure 25. Sector/Sector Block Protect and Unprotect Timing Diagram ............................................................. 47 Alternate CE# Controlled Erase and Program Operations ........ 48 Figure 26. Alternate CE# Controlled Write (Erase/Program) Operation Timings .............................................. 49 Erase And Programming Performance . . . . . . . 50 Latchup Characteristics . . . . . . . . . . . . . . . . . . . 50 TSOP and BGA Package Capacitance . . . . . . . . 50 Data Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 51 FBD048—48-ball Fine-Pitch Ball Grid Array (FBGA) 6 x 12 mm package ................................................................... 51 TS 048—48-Pin Standard TSOP ............................................... 52 Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 53 Am29LV320D 5 PRODUCT SELECTOR GUIDE Family Part Number Am29LV320D Standard Voltage Range: VCC = 2.7–3.6 V 90R Standard Voltage Range: VCC = 3.0–3.6 V Speed Option 90 120 Max Access Time (ns) 90 120 CE# Access (ns) 90 120 OE# Access (ns) 40 50 BLOCK DIAGRAM DQ0–DQ15 (A-1) RY/BY# VCC Sector Switches VSS Erase Voltage Generator RESET# WE# BYTE# Input/Output Buffers State Control Command Register PGM Voltage Generator Chip Enable Output Enable Logic CE# OE# VCC Detector A0–A20 6 Timer Address Latch STB Am29LV320D STB Data Latch Y-Decoder Y-Gating X-Decoder Cell Matrix November 15, 2004 CONNECTION DIAGRAMS A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# NC WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 November 15, 2004 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48-Pin Standard TSOP Am29LV320D 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 7 CONNECTION DIAGRAMS 48-Ball FBGA Top View, Balls Facing Down A6 B6 C6 D6 E6 A13 A12 A14 A15 A16 A5 B5 C5 D5 E5 F5 G5 H5 A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6 G6 BYTE# DQ15/A-1 H6 VSS A4 B4 C4 D4 E4 F4 G4 H4 WE# RESET# NC A19 DQ5 DQ12 VCC DQ4 A3 B3 C3 D3 E3 F3 G3 H3 A18 A20 DQ2 DQ10 DQ11 DQ3 RY/BY# WP#/ACC A2 B2 C2 D2 E2 F2 G2 H2 A7 A17 A6 A5 DQ0 DQ8 DQ9 DQ1 A1 B1 C1 D1 E1 F1 G1 H1 OE# VSS A3 A4 A2 A1 Special Package Handling Instructions Special handling is required for Flash Memory products in molded (TSOP, BGA) packages. 8 F6 A0 CE# The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. Am29LV320D November 15, 2004 PIN DESCRIPTION A0–A20 LOGIC SYMBOL = 21 Addresses 21 DQ0–DQ14 = 15 Data Inputs/Outputs A0–A2 DQ15/A-1 = DQ15 (Data Input/Output, word mode), A-1 (LSB Address Input, byte mode) CE# = Chip Enable OE# = Output Enable WE# = Write Enable DQ0–DQ15 (A-1) CE# OE# WE# WP#/ACC WP#/ACC = Hardware Write Protect/ Acceleration Pin RESET# RESET# = Hardware Reset Pin, Active Low BYTE# BYTE# = Selects 8-bit or 16-bit mode RY/BY# = Ready/Busy Output VCC = 3.0 volt-only single power supply (see Product Selector Guide for speed options and voltage supply tolerances) VSS = Device Ground NC = Pin Not Connected Internally November 15, 2004 16 or 8 Am29LV320D RY/BY# 9 ORDERING INFORMATION Standard Products AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the following: Am29LV32 0D T 90 E C TEMPERATURE RANGE I = Industrial (–40°C to +85°C) F = Industrial (–40°C to +85°C) with Pb-free package C = Commercial (0°C to +70°C) D = Commercial (0°C to +70°C) with Pb-free package V = Automotive In-Cabin (-40°C to +105°C) Y = Automotive In-Cabin (-40°C to +105°C) with Pb-free package PACKAGE TYPE E = 48-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 048) WM = 48-ball Fine-Pitch Ball Grid Array (FBGA) 0.80 mm pitch, 6 x 12 mm package (FBD048) SPEED OPTION See Product Selector Guide and Valid Combinations BOOT CODE SECTOR ARCHITECTURE T = Top boot sector B = Bottom boot sector DEVICE NUMBER/DESCRIPTION Am29LV320D 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS Boot Sector Flash Memory 3.0 Volt-only Read, Program and Erase Valid Combinations for TSOP Packages AM29LV320DT90R, AM29LV320DB90R Am29LV320DT90, Am29LV320DB90 EC, EI, ED, EF AM29LV320DT120, AM29LV320DB120 Am29LV320DT120 Am29LV320DB120 EV, EY Speed (Ns) VCC Range Valid Combinations for FBGA Packages Order Number 90 3.0– 3.6V AM29LV320DT90, AM29LV320DB90 90 2.7– 3.6V AM29LV320DT120, AM29LV320DB120 120 2.7– 3.6V Am29LV320DT120 120 2.7 – 3,6V Am29LV320DB120 Package Marking WMC,W L320DT90V, L320DB90V MI, WMD, L320DT12V, WMF L320DB12V WNV L320DT12V L320DB12V C, I, D, F V, Y Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations. 10 Am29LV320D November 15, 2004 DEVICE BUS OPERATIONS This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The contents of the Table 1. register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail. Am29LV320D Device Bus Operations DQ8–DQ15 Operation CE# OE# WE # RESET # WP#/AC C Addresses (Note 2) DQ0– DQ7 BYTE # = VIH DOUT DOUT BYTE# = VIL Read L L H H L/H AIN Write L H L H (Note 3) AIN (Note 4) (Note 4) Accelerated Program L H L H VHH AIN (Note 4) (Note 4) VCC ± 0.3 V X X VCC ± 0.3 V H X High-Z High-Z High-Z Output Disable L H H H L/H X High-Z High-Z High-Z Reset X X X L L/H X High-Z High-Z High-Z Sector Protect (Note 2) L H L VID L/H SA, A6 = L, (Note 4) A1 = H, A0 = L X X Sector Unprotect (Note 2) L H L VID (Note 3) SA, A6 = H, (Note 4) A1 = H, A0 = L X X Temporary Sector Unprotect X X X VID (Note 3) Standby AIN (Note 4) (Note 4) DQ8–DQ14 = High-Z, DQ15 = A-1 High-Z Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector Address, AIN = Address In, DIN = Data In, DOUT = Data Out Notes: 1. Addresses are A20:A0 in word mode (BYTE# = VIH), A20:A-1 in byte mode (BYTE# = VIL). 2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See “Sector/Sector Block Protection and Unprotection” on page 17. 3. If WP#/ACC = VIL, the two outermost boot sectors remain protected. If WP#/ACC = VIH, the two outermost boot sector protection depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection” on page 17. If WP#/ACC = VHH, all sectors are unprotected. 4. DIN or DOUT as required by command sequence, data polling, or sector protection algorithm. Word/Byte Configuration The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ0–DQ15 are active and controlled by CE# and OE#. If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ0–DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8–DQ14 are November 15, 2004 tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function. Requirements for Reading Array Data To read array data from the outputs, the system must drive the CE# and OE# pins to VIL . CE# is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at VIH. The BYTE# pin determines whether the device outputs array data in words or bytes. Am29LV320D 11 The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. See “Requirements for Reading Array Data” on page 11 for more information. Refer to the AC Read-Only Operations table for timing specifications and to Figure 14, on page 38 for the timing diagram. ICC1 in the DC Characteristics table represents the active current specification for reading array data. Writing Commands/Command Sequences To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH. For program operations, the BYTE# pin determines whether the device accepts program data in bytes or words. Refer to “Word/Byte Configuration” on page 11 for more information. The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The “Word/Byte Configuration” on page 11 section contains details on programming data to the device using both standard and Unlock Bypass command sequences. An erase operation can erase one sector, multiple sectors, or the entire device. Table 2, on page 13 through Table 5, on page 16 indicate the address space that each sector occupies. A “sector address” is the address bits required to uniquely select a sector. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The “AC Characteristics” on page 38 section contains timing specification tables and timing diagrams for write operations. Accelerated Program Operation The device offers accelerated program operations through the ACC function. This is one of two functions provided by the WP#/ACC pin. 12 This function is primarily intended to allow faster manufacturing throughput at the factory. If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be at V HH for operations other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Autoselect Functions If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. Refer to the “Autoselect Mode” on page 16 and “Autoselect Command Sequence” on page 25 sections for more information. I CC6 and I CC7 in the DC Characteristics table represent the current specifications for read-while-program and read-while-erase, respectively. Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# pins are both held at V CC ± 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VCC ± 0.3 V, the device is in the standby mode, but the standby current is greater. The device requires standard access time (tCE) for read access when the device is in either of these standby modes, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. ICC3 in the DC Characteristics table represents the standby current specification. Am29LV320D November 15, 2004 Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for t ACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC4 in the “DC Characteristics” on page 35 table represents the automatic sleep mode current specification. RESET#: Hardware Reset Pin The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. (ICC4). If RESET# is held at VIL but not within VSS±0.3 V, the standby current is greater. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a “0” (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the reset operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the RESET# pin returns to VIH. Refer to the AC Characteristics tables for RESET# parameters and to Figure 15, on page 39 for the timing diagram. Output Disable Mode When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high impedance state. Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3 V, the device draws CMOS standby current Table 2. Top Boot Sector Addresses (Am29LV320DT) (Sheet 1 of 2) Sector Sector Address A20–A12 SA0 000000xxx SA1 000001xxx SA2 000010xxx SA3 SA4 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range 64/32 000000h–00FFFFh 000000h–07FFFh 64/32 010000h–01FFFFh 008000h–0FFFFh 64/32 020000h–02FFFFh 010000h–17FFFh 000011xxx 64/32 030000h–03FFFFh 018000h–01FFFFh 000100xxx 64/32 040000h–04FFFFh 020000h–027FFFh SA5 000101xxx 64/32 050000h–05FFFFh 028000h–02FFFFh SA6 000110xxx 64/32 060000h–06FFFFh 030000h–037FFFh SA7 000111xxx 64/32 070000h–07FFFFh 038000h–03FFFFh SA8 001000xxx 64/32 080000h–08FFFFh 040000h–047FFFh SA9 001001xxx 64/32 090000h–09FFFFh 048000h–04FFFFh SA10 001010xxx 64/32 0A0000h–0AFFFFh 050000h–057FFFh SA11 001011xxx 64/32 0B0000h–0BFFFFh 058000h–05FFFFh SA12 001100xxx 64/32 0C0000h–0CFFFFh 060000h–067FFFh SA13 001101xxx 64/32 0D0000h–0DFFFFh 068000h–06FFFFh SA14 001110xxx 64/32 0E0000h–0EFFFFh 070000h–077FFFh SA15 001111xxx 64/32 0F0000h–0FFFFFh 078000h–07FFFFh SA16 010000xxx 64/32 100000h–10FFFFh 080000h–087FFFh SA17 010001xxx 64/32 110000h–11FFFFh 088000h–08FFFFh SA18 010010xxx 64/32 120000h–12FFFFh 090000h–097FFFh November 15, 2004 Am29LV320D 13 Table 2. Top Boot Sector Addresses (Am29LV320DT) (Sheet 2 of 2) Sector Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range SA19 010011xxx 64/32 130000h–13FFFFh 098000h–09FFFFh SA20 010100xxx 64/32 140000h–14FFFFh 0A0000h–0A7FFFh SA21 010101xxx 64/32 150000h–15FFFFh 0A8000h–0AFFFFh SA22 010110xxx 64/32 160000h–16FFFFh 0B0000h–0B7FFFh SA23 010111xxx 64/32 170000h–17FFFFh 0B8000h–0BFFFFh SA24 011000xxx 64/32 180000h–18FFFFh 0C0000h–0C7FFFh SA25 011001xxx 64/32 190000h–19FFFFh 0C8000h–0CFFFFh SA26 011010xxx 64/32 1A0000h–1AFFFFh 0D0000h–0D7FFFh SA27 011011xxx 64/32 1B0000h–1BFFFFh 0D8000h–0DFFFFh SA28 011100xxx 64/32 1C0000h–1CFFFFh 0E0000h–0E7FFFh SA29 011101xxx 64/32 1D0000h–1DFFFFh 0E8000h–0EFFFFh SA30 011110xxx 64/32 1E0000h–1EFFFFh 0F0000h–0F7FFFh SA31 011111xxx 64/32 1F0000h–1FFFFFh 0F8000h–0FFFFFh SA32 100000xxx 64/32 200000h–20FFFFh 100000h–107FFFh SA33 100001xxx 64/32 210000h–21FFFFh 108000h–10FFFFh SA34 100010xxx 64/32 220000h–22FFFFh 110000h–117FFFh SA35 100011xxx 64/32 230000h–23FFFFh 118000h–11FFFFh SA36 100100xxx 64/32 240000h–24FFFFh 120000h–127FFFh SA37 100101xxx 64/32 250000h–25FFFFh 128000h–12FFFFh SA38 100110xxx 64/32 260000h–26FFFFh 130000h–137FFFh SA39 100111xxx 64/32 270000h–27FFFFh 138000h–13FFFFh SA40 101000xxx 64/32 280000h–28FFFFh 140000h–147FFFh SA41 101001xxx 64/32 290000h–29FFFFh 148000h–14FFFFh SA42 101010xxx 64/32 2A0000h–2AFFFFh 150000h–157FFFh SA43 101011xxx 64/32 2B0000h–2BFFFFh 158000h–15FFFFh SA44 101100xxx 64/32 2C0000h–2CFFFFh 160000h–167FFFh SA45 101101xxx 64/32 2D0000h–2DFFFFh 168000h–16FFFFh SA46 101110xxx 64/32 2E0000h–2EFFFFh 170000h–177FFFh SA47 101111xxx 64/32 2F0000h–2FFFFFh 178000h–17FFFFh SA48 110000xxx 64/32 300000h–30FFFFh 180000h–187FFFh SA49 110001xxx 64/32 310000h–31FFFFh 188000h–18FFFFh SA50 110010xxx 64/32 320000h–32FFFFh 190000h–197FFFh SA51 110011xxx 64/32 330000h–33FFFFh 198000h–19FFFFh SA52 110100xxx 64/32 340000h–34FFFFh 1A0000h–1A7FFFh SA53 110101xxx 64/32 350000h–35FFFFh 1A8000h–1AFFFFh SA54 110110xxx 64/32 360000h–36FFFFh 1B0000h–1B7FFFh SA55 110111xxx 64/32 370000h–37FFFFh 1B8000h–1BFFFFh SA56 111000xxx 64/32 380000h–38FFFFh 1C0000h–1C7FFFh SA57 111001xxx 64/32 390000h–39FFFFh 1C8000h–1CFFFFh SA58 111010xxx 64/32 3A0000h–3AFFFFh 1D0000h–1D7FFFh SA59 111011xxx 64/32 3B0000h–3BFFFFh 1D8000h–1DFFFFh SA60 111100xxx 64/32 3C0000h–3CFFFFh 1E0000h–1E7FFFh SA61 111101xxx 64/32 3D0000h–3DFFFFh 1E8000h–1EFFFFh SA62 111110xxx 64/32 3E0000h–3EFFFFh 1F0000h–1F7FFFh SA63 111111000 8/4 3F0000h–3F1FFFh 1F8000h–1F8FFFh SA64 111111001 8/4 3F2000h–3F3FFFh 1F9000h–1F9FFFh SA65 111111010 8/4 3F4000h–3F5FFFh 1FA000h–1FAFFFh SA66 111111011 8/4 3F6000h–3F7FFFh 1FB000h–1FBFFFh SA67 111111100 8/4 3F8000h–3F9FFFh 1FC000h–1FCFFFh SA68 111111101 8/4 3FA000h–3FBFFFh 1FD000h–1FDFFFh SA69 111111110 8/4 3FC000h–3FDFFFh 1FE000h–1FEFFFh SA70 111111111 8/4 3FE000h–3FFFFFh 1FF000h–1FFFFFh Note: The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH). Table 3. 14 Top Boot SecSiTM Sector Addresses Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range 111111xxx 64/32 3F0000h–3FFFFFh 1F8000h–1FFFFFh Am29LV320D November 15, 2004 Table 4. Bottom Boot Sector Addresses (Am29LV320DB) (Sheet 1 of 2) Sector Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range SA0 000000000 8/4 000000h-001FFFh 000000h–000FFFh SA1 000000001 8/4 002000h-003FFFh 001000h–001FFFh SA2 000000010 8/4 004000h-005FFFh 002000h–002FFFh SA3 000000011 8/4 006000h-007FFFh 003000h–003FFFh SA4 000000100 8/4 008000h-009FFFh 004000h–004FFFh SA5 000000101 8/4 00A000h-00BFFFh 005000h–005FFFh SA6 000000110 8/4 00C000h-00DFFFh 006000h–006FFFh SA7 000000111 8/4 00E000h-00FFFFh 007000h–007FFFh SA8 000001xxx 64/32 010000h-01FFFFh 008000h–00FFFFh SA9 000010xxx 64/32 020000h-02FFFFh 010000h–017FFFh SA10 000011xxx 64/32 030000h-03FFFFh 018000h–01FFFFh SA11 000100xxx 64/32 040000h-04FFFFh 020000h–027FFFh SA12 000101xxx 64/32 050000h-05FFFFh 028000h–02FFFFh SA13 000110xxx 64/32 060000h-06FFFFh 030000h–037FFFh SA14 000111xxx 64/32 070000h-07FFFFh 038000h–03FFFFh SA15 001000xxx 64/32 080000h-08FFFFh 040000h–047FFFh SA16 001001xxx 64/32 090000h-09FFFFh 048000h–04FFFFh SA17 001010xxx 64/32 0A0000h-0AFFFFh 050000h–057FFFh SA18 001011xxx 64/32 0B0000h-0BFFFFh 058000h–05FFFFh SA19 001100xxx 64/32 0C0000h-0CFFFFh 060000h–067FFFh SA20 001101xxx 64/32 0D0000h-0DFFFFh 068000h–06FFFFh SA21 001110xxx 64/32 0E0000h-0EFFFFh 070000h–077FFFh SA22 001111xxx 64/32 0F0000h-0FFFFFh 078000h–07FFFFh SA23 010000xxx 64/32 100000h-10FFFFh 080000h–087FFFh SA24 010001xxx 64/32 110000h-11FFFFh 088000h–08FFFFh SA25 010010xxx 64/32 120000h-12FFFFh 090000h–097FFFh SA26 010011xxx 64/32 130000h-13FFFFh 098000h–09FFFFh SA27 010100xxx 64/32 140000h-14FFFFh 0A0000h–0A7FFFh SA28 010101xxx 64/32 150000h-15FFFFh 0A8000h–0AFFFFh SA29 010110xxx 64/32 160000h-16FFFFh 0B0000h–0B7FFFh SA30 010111xxx 64/32 170000h-17FFFFh 0B8000h–0BFFFFh SA31 011000xxx 64/32 180000h-18FFFFh 0C0000h–0C7FFFh SA32 011001xxx 64/32 190000h-19FFFFh 0C8000h–0CFFFFh SA33 011010xxx 64/32 1A0000h-1AFFFFh 0D0000h–0D7FFFh SA34 011011xxx 64/32 1B0000h-1BFFFFh 0D8000h–0DFFFFh SA35 011100xxx 64/32 1C0000h-1CFFFFh 0E0000h–0E7FFFh SA36 011101xxx 64/32 1D0000h-1DFFFFh 0E8000h–0EFFFFh SA37 011110xxx 64/32 1E0000h-1EFFFFh 0F0000h–0F7FFFh SA38 011111xxx 64/32 1F0000h-1FFFFFh 0F8000h–0FFFFFh SA39 100000xxx 64/32 200000h-20FFFFh 100000h–107FFFh SA40 100001xxx 64/32 210000h-21FFFFh 108000h–10FFFFh SA41 100010xxx 64/32 220000h-22FFFFh 110000h–117FFFh SA42 100011xxx 64/32 230000h-23FFFFh 118000h–11FFFFh SA43 100100xxx 64/32 240000h-24FFFFh 120000h–127FFFh SA44 100101xxx 64/32 250000h-25FFFFh 128000h–12FFFFh SA45 100110xxx 64/32 260000h-26FFFFh 130000h–137FFFh SA46 100111xxx 64/32 270000h-27FFFFh 138000h–13FFFFh SA47 101000xxx 64/32 280000h-28FFFFh 140000h–147FFFh SA48 101001xxx 64/32 290000h-29FFFFh 148000h–14FFFFh SA49 101010xxx 64/32 2A0000h-2AFFFFh 150000h–157FFFh SA50 101011xxx 64/32 2B0000h-2BFFFFh 158000h–15FFFFh SA51 101100xxx 64/32 2C0000h-2CFFFFh 160000h–167FFFh SA52 101101xxx 64/32 2D0000h-2DFFFFh 168000h–16FFFFh November 15, 2004 Am29LV320D 15 Table 4. Bottom Boot Sector Addresses (Am29LV320DB) (Sheet 2 of 2) Sector Address A20–A12 Sector Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range 170000h–177FFFh SA53 101110xxx 64/32 2E0000h-2EFFFFh SA54 101111xxx 64/32 2F0000h-2FFFFFh 178000h–17FFFFh SA55 111000xxx 64/32 300000h-30FFFFh 180000h–187FFFh SA56 110001xxx 64/32 310000h-31FFFFh 188000h–18FFFFh SA57 110010xxx 64/32 320000h-32FFFFh 190000h–197FFFh SA58 110011xxx 64/32 330000h-33FFFFh 198000h–19FFFFh SA59 110100xxx 64/32 340000h-34FFFFh 1A0000h–1A7FFFh SA60 110101xxx 64/32 350000h-35FFFFh 1A8000h–1AFFFFh SA61 110110xxx 64/32 360000h-36FFFFh 1B0000h–1B7FFFh SA62 110111xxx 64/32 370000h-37FFFFh 1B8000h–1BFFFFh SA63 111000xxx 64/32 380000h-38FFFFh 1C0000h–1C7FFFh SA64 111001xxx 64/32 390000h-39FFFFh 1C8000h–1CFFFFh SA65 111010xxx 64/32 3A0000h-3AFFFFh 1D0000h–1D7FFFh SA66 111011xxx 64/32 3B0000h-3BFFFFh 1D8000h–1DFFFFh SA67 111100xxx 64/32 3C0000h-3CFFFFh 1E0000h–1E7FFFh SA68 111101xxx 64/32 3D0000h-3DFFFFh 1E8000h–1EFFFFh SA69 111110xxx 64/32 3E0000h-3EFFFFh 1F0000h–1F7FFFh SA70 111111xxx 64/32 3F0000h-3FFFFFh 1F8000h–1FFFFFh Note: The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH). Bottom Boot SecSiTM Sector Addresses Table 5. Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range 000000xxx 64/32 000000h-00FFFFh 00000h-07FFFh sector address must appear on the appropriate highest order address bits (see Table 2, on page 13 through Table 5, on page 16). Table 6, on page 16 shows the remaining address bits that are don’t care. When all necessary bits are set as required, the programming equipment may then read the corresponding identifier code on DQ7–DQ0. Autoselect Mode The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system through the command register. To access the autoselect codes in-system, the host system can issue the autoselect command v i a t h e c o m m a n d r e g i s t e r, a s s h o w n i n Table 14, on page 29. This method does not require VID. Refer to the “Autoselect Command Sequence” on page 25 section for more information. When using programming equipment, the autoselect mode requires VID (11.5 V to 12.5 V) on address pin A9. Address pins A6, A1, and A0 must be as shown in Table 6, on page 16. In addition, when verifying sector protection, the Table 6. Autoselect Codes (High Voltage Method) DQ8 to DQ15 CE# OE# WE# A20 to A12 A11 to A10 A9 A8 to A7 A6 A5 to A2 A1 A0 Manufacturer ID: AMD L L H X X VID X L X L L X X 01h Device ID: Am29LV320D L L H X X VID X L X L H 22h X F6 (T), F9h (B) Sector Protection Verification L L H SA X VID X L X H L X X 01h (protected), 00h (unprotected) SecSiTM Sector Indicator Bit (DQ7) L L H X X VID X L X H H X X 99h (factory locked), 19h (not factory locked) Description BYTE# BYTE# = VIH = VIL DQ7 to DQ0 Legend: T = Top Boot Block, B = Bottom Boot Block, L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care. 16 Am29LV320D November 15, 2004 Table 8. Bottom Boot Sector/Sector Block Addresses for Protection/Unprotection Sector/Sector Block Protection and Unprotection The hardware sector protection feature disables both program and erase operations in any sector. The hardware sector unprotection feature re-enables both program and erase operations in previously protected sectors. Sector protection/unprotection can be implemented via two methods. (Note: For the following discussion, the term “sector” applies to both sectors and sector blocks. A sector block consists of two or more adjacent sectors that are protected or unprotected at the same tim e (see Table 7 , on page 17 and Table 8, on page 17). Table 7. Top Boot Sector/Sector Block Addresses for Protection/Unprotection A20–A12 Sector/Sector Block Size SA70-SA67 111111XXX, 111110XXX, 111101XXX, 111100XXX 256 (4x64) Kbytes SA66-SA63 1110XXXXX 256 (4x64) Kbytes SA62-SA59 1101XXXXX 256 (4x64) Kbytes SA58-SA55 1100XXXXX 256 (4x64) Kbytes SA54-SA51 1011XXXXX 256 (4x64) Kbytes SA50-SA47 1010XXXXX 256 (4x64) Kbytes SA46-SA43 1001XXXXX 256 (4x64) Kbytes SA42-SA39 1000XXXXX 256 (4x64) Kbytes SA38-SA35 0111XXXXX 256 (4x64) Kbytes SA34-SA31 0110XXXXX 256 (4x64) Kbytes SA30-SA27 0101XXXXX 256 (4x64) Kbytes SA26-SA23 0100XXXXX 256 (4x64) Kbytes SA22–SA19 0011XXXXX 256 (4x64) Kbytes SA18-SA15 0010XXXXX 256 (4x64) Kbytes SA14-SA11 0001XXXXX 256 (4x64) Kbytes SA10-SA8 000011XXX, 000010XXX, 000001XXX 192 (3x64) Kbytes Sector / Sector Block A20–A12 SA0-SA3 000000XXX, 000001XXX, 000010XXX 000011XXX 256 (4x64) Kbytes SA4-SA7 0001XXXXX 256 (4x64) Kbytes SA8-SA11 0010XXXXX 256 (4x64) Kbytes SA7 000000111 8 Kbytes SA12-SA15 0011XXXXX 256 (4x64) Kbytes SA6 000000110 8 Kbytes SA16-SA19 0100XXXXX 256 (4x64) Kbytes SA5 000000101 8 Kbytes SA20-SA23 0101XXXXX 256 (4x64) Kbytes SA4 000000100 8 Kbytes 256 (4x64) Kbytes SA3 000000011 8 Kbytes 256 (4x64) Kbytes SA2 000000010 8 Kbytes 000000001 8 Kbytes 000000000 8 Kbytes SA24-SA27 SA28-SA31 0110XXXXX 0111XXXXX Sector/Sector Block Size Sector / Sector Block SA32-SA35 1000XXXXX 256 (4x64) Kbytes SA1 SA36-SA39 1001XXXXX 256 (4x64) Kbytes SA0 SA40-SA43 1010XXXXX 256 (4x64) Kbytes SA44-SA47 1011XXXXX 256 (4x64) Kbytes SA48-SA51 1100XXXXX 256 (4x64) Kbytes SA52-SA55 1101XXXXX 256 (4x64) Kbytes SA56-SA59 1110XXXXX 256 (4x64) Kbytes SA60-SA62 111100XXX, 111101XXX, 111110XXX 192 (3x64) Kbytes SA63 111111000 8 Kbytes SA64 111111001 8 Kbytes SA65 111111010 8 Kbytes SA66 111111011 8 Kbytes SA67 111111100 8 Kbytes SA68 111111101 8 Kbytes SA69 111111110 8 Kbytes SA70 111111111 8 Kbytes Sector Protection and unprotection requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 2, on page 19 shows the algorithms and Figure 25, on page 47 shows the timing diagram. This method uses standard microprocessor bus cycle timing. For sector unprotect, all unprotected sectors must first be protected prior to the first sector unprotect write cycle. The sector unprotect algorithm unprotects all sectors in parallel. All previously protected sectors must be individually re-protected. To change data in protected sectors efficiently, the temporary sector unprotect function is available. See “Temporary Sector Unprotect” on page 18. The alternate method intended only for programming equipment, and requires VID on address pin A9 and OE#. This method is November 15, 2004 Am29LV320D 17 compatible with programmer routines written for earlier 3.0 volt-only AMD flash devices. For detailed information, contact an AMD representative. 23, on page 46 shows the timing diagrams, for this feature. The device is shipped with all sectors unprotected. AMD offers the option of programming and protecting sectors at its factory prior to shipping the device through AMD’s ExpressFlash™ Service. Contact an AMD representative for details. START RESET# = VID (Note 1) It is possible to determine whether a sector is protected or unprotected. See “Autoselect Mode” on page 16 for details. Perform Erase or Program Write Protect (WP#) RESET# = VIH The Write Protect function provides a hardware method of protecting certain boot sectors without using VID. This function is one of two provided by the WP#/ACC pin. If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the two “outermost” 8 Kbyte boot sectors independently of whether those sectors w er e p r ote cte d or un pro tec ted usi ng the method described in “Sector/Sector Block Protection and Unprotection” on page 17. The two outermost 8 Kbyte boot sectors are the two sectors containing the lowest addresses in a bottom-boot-configured device, or the two sectors containing the highest addresses in a top-boot-configured device. If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the two outermost 8K Byte boot sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these two sectors depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection” on page 17. Temporary Sector Unprotect Completed (Note 2) Notes: 1. All protected sectors unprotected (If WP#/ACC = VIL, outermost boot sectors remain protected). 2. All previously protected sectors are protected once again. Figure 1. Temporary Sector Unprotect Operation Note that the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Temporary Sector Unprotect This feature allows temporary unprotection of previously protected sectors to change data in-system. The Sector Unprotect mode is activated by setting the RESET# pin to VID (11.5 V – 12.5 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once VID is removed from the RESET# pin, all the previously protected sectors are protected again. Figure 1, on page 18 shows the algorithm, and Figure 18 Am29LV320D November 15, 2004 START START Protect all sectors: The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address PLSCNT = 1 RESET# = VID Wait 1 µs Temporary Sector Unprotect Mode No PLSCNT = 1 RESET# = VID Wait 1 µs No First Write Cycle = 60h? First Write Cycle = 60h? Yes Yes Set up sector address No All sectors protected? Sector Protect: Write 60h to sector address with A6 = 0, A1 = 1, A0 = 0 Yes Set up first sector address Sector Unprotect: Write 60h to sector address with A6 = 1, A1 = 1, A0 = 0 Wait 150 µs Increment PLSCNT Temporary Sector Unprotect Mode Verify Sector Protect: Write 40h to sector address with A6 = 0, A1 = 1, A0 = 0 Reset PLSCNT = 1 Wait 15 ms Read from sector address with A6 = 0, A1 = 1, A0 = 0 Verify Sector Unprotect: Write 40h to sector address with A6 = 1, A1 = 1, A0 = 0 Increment PLSCNT No No PLSCNT = 25? Yes Yes No Yes Device failed PLSCNT = 1000? Protect another sector? No Yes Remove VID from RESET# Device failed Write reset command Sector Protect Algorithm Read from sector address with A6 = 1, A1 = 1, A0 = 0 Data = 01h? Set up next sector address No Data = 00h? Yes Last sector verified? No Yes Sector Protect complete Sector Unprotect Algorithm Remove VID from RESET# Write reset command Sector Unprotect complete Figure 2. November 15, 2004 In-System Sector Protect/Unprotect Algorithms Am29LV320D 19 SecSiTM Sector (Secured Silicon) Flash Memory Region ■ Customer code through the ExpressFlash service The Secured Silicon Sector (SecSi Sector) feature provides a Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The SecSi Sector uses a SecSi Sector Indicator Bit (DQ7) to indicate whether or not the SecSi Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. Note that the Am29LV320D has a SecSi Sector size of 64 Kbytes. AMD devices designated as replacements or substitutes, such as the Am29LV320M, have 256 bytes. This should be considered during system design. AMD offers the device with the SecSi Sector either factory locked or customer lockable. The factory-locked version is always protected when shipped from the factory, and has the SecSi Sector Indicator Bit permanently set to a “1.” The customer-lockable version is shipped with the SecSi Sector unprotected, allowing customers to utilize the that sector in any manner they choose. The customer-lockable version has the SecSi Sector Indicator Bit permanently set to a “0.” Thus, the SecSi Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory locked. The system accesses the SecSi Sector through a command sequence (see “Enter SecSiTM Sector/Exit SecSi Sector Command Sequence” on page 26). After the system writes the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by the boot sectors. This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending commands to the boot sectors. Factory Locked: SecSi Sector Programmed and Protected at the Factory In a factory locked device, the SecSi Sector is protected when the device is shipped from the factory. The SecSi Sector cannot be modified in a ny way. T h e d ev i ce i s a va i la bl e p r e p r ogrammed with one of the following: ■ A random, secure ESN only 20 ■ Both a random, secure ESN and customer code through the ExpressFlash service. In devices that have an ESN, a Bottom Boot device has the 16-byte (8-word) ESN in sector 0 at addresses 00000h–0000Fh in byte mode (or 00000h–00007h in word mode). In the Top Boot device the ESN is in sector 63 at addresses 3F0000h–3F000Fh in byte mode (or 1F8000h–1F8007h in word mode). Note that in upcoming top boot versions of this device, the E SN is l ocate d i n se cto r 7 0 at add res ses 3FE000h–3FE00Fh in byte mode (or 1FF000h–1FF007h in word mode). Customers may opt to have their code programmed by AMD through the AMD ExpressFlash service. AMD programs the customer’s code, with or without the random ESN. The devices are then shipped from AMD’s factory with the SecSi Sector permanently locked. Contact an AMD representative for details on using AMD’s ExpressFlash service. Customer Lockable: SecSi Sector NOT Programmed or Protected at the Factory The customer lockable version allows the SecSi Sector to be programmed once and then permanently locked after it ships from AMD. Note that the Am29LV320D has a SecSi Sector size of 64 Kbytes. AMD devices designated as replacements or substitutes, such as the Am29LV320M, have 256 bytes. This should be considered during system design. Additionally, note the change in the location of the ESN in upcoming top boot factory locked devices. Note that the accelerated programming (ACC) and unlock bypass functions are not available when programming the SecSi Sector. The SecSi Sector area can be protected using the following procedures: ■ Write the three-cycle Enter SecSi Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 2, on page 19, except that RESET# may be at either V IH or V ID . This allows in-system protection of the SecSi Sector without raising any device pin to a high voltage. Note that this method is only applicable to the SecSi Sector. ■ To verify the protect/unprotect status of the SecSi Sector, follow the algorithm shown in Figure 3, on page 21. Am29LV320D November 15, 2004 Once the SecSi Sector is locked and verified, the system must write the Exit SecSi Sector Region command sequence to return to reading and writing the remainder of the array. until VCC is greater than VLKO. The system must provide the proper signals to the control pins to p reven t un inte ntion al w rite s w hen V C C is greater than VLKO. The SecSi Sector protection must be used with caution since, once protected, there is no procedure available for unprotecting the SecSi Sector area and none of the bits in the SecSi Sector memory space can be modified in any way. Write Pulse “Glitch” Protection START RESET# = VIH or VID Wait 1 µs Write 60h to any address Write 40h to SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Read from SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Figure 3. Logical Inhibit Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. Power-Up Write Inhibit If data = 00h, SecSi Sector is unprotected. If data = 01h, SecSi Sector is protected. If WE# = CE# = V IL and OE# = V IH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. COMMON FLASH MEMORY INTERFACE (CFI) Remove VIH or VID from RESET# The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. Write reset command SecSi Sector Protect Verify complete SecSi Sector Protect Verify Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes (refer to Table 14, on page 29 for command definitions). In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to the read mode. Subsequent writes are ignored November 15, 2004 Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h in word mode (or address AAh in byte mode), any time the device is ready to read array data. The system can read CFI information at the addresses given in Table 9, on page 22 through Table 12, on page 24. To terminate reading CFI data, the system must write the reset command. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Table 9, on page 22 through Table 12, on page 24. The system must write the reset command to return the device to the reading array data. For further information, please refer to the CFI Specification and CFI Publication 100, available via the Wo r l d Wide We b at http://www.amd.com/flash/cfi. Alternatively, contact an AMD representative for copies of these documents. Am29LV320D 21 Table 9. Addresses Addresses (Word Mode) (Byte Mode) CFI Query Identification String Data 10h 11h 12h 20h 22h 24h 0051h 0052h 0059h Query Unique ASCII string “QRY” 13h 14h 26h 28h 0002h 0000h Primary OEM Command Set 15h 16h 2Ah 2Ch 0040h 0000h Address for Primary Extended Table 17h 18h 2Eh 30h 0000h 0000h Alternate OEM Command Set (00h = none exists) 19h 1Ah 32h 34h 0000h 0000h Address for Alternate OEM Extended Table (00h = none exists) Table 10. Addresses Addresses (Word Mode) (Byte Mode) 22 Description System Interface String Data Description 1Bh 36h 0027h VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Ch 38h 0036h VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Dh 3Ah 0000h VPP Min. voltage (00h = no VPP pin present) 1Eh 3Ch 0000h VPP Max. voltage (00h = no VPP pin present) 1Fh 3Eh 0004h Typical timeout per single byte/word write 2N µs 20h 40h 0000h Typical timeout for Min. size buffer write 2N 21h 42h 000Ah Typical timeout per individual block erase 2 ms 22h 44h 0000h Typical timeout for full chip erase 2N ms (00h = not supported) 23h 46h 0005h Max. timeout for byte/word write 2N times typical 24h 48h 0000h Max. timeout for buffer write 2N times typical 25h 4Ah 0004h Max. timeout per individual block erase 2N times typical 26h 4Ch 0000h Max. timeout for full chip erase 2N times typical (00h = not supported) µs (00h = not supported) N Am29LV320D November 15, 2004 Table 11. Addresses Addresses (Word Mode) (Byte Mode) Device Geometry Definition Data Description 27h 4Eh 0016h Device Size = 2 byte 28h 29h 50h 52h 0002h 0000h Flash Device Interface description (refer to CFI publication 100) 2Ah 2Bh 54h 56h 0000h 0000h Max. number of bytes in multi-byte write = 2N (00h = not supported) 2Ch 58h 0002h Number of Erase Block Regions within device 2Dh 2Eh 2Fh 30h 5Ah 5Ch 5Eh 60h 0007h 0000h 0020h 0000h Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) 31h 32h 33h 34h 62h 64h 66h 68h 003Eh 0000h 0000h 0001h Erase Block Region 2 Information 35h 36h 37h 38h 6Ah 6Ch 6Eh 70h 0000h 0000h 0000h 0000h Erase Block Region 3 Information 39h 3Ah 3Bh 3Ch 72h 74h 76h 78h 0000h 0000h 0000h 0000h Erase Block Region 4 Information November 15, 2004 N Am29LV320D 23 Table 12. Addresses Addresses (Word Mode) (Byte Mode) Primary Vendor-Specific Extended Query Data Description 40h 41h 42h 80h 82h 84h 0050h 0052h 0049h Query-unique ASCII string “PRI” 43h 86h 0031h Major version number, ASCII 44h 88h 0031h Minor version number, ASCII 45h 8Ah 0000h Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Silicon Revision Number (Bits 7-2) 24 46h 8Ch 0002h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write 47h 8Eh 0004h Sector Protect 0 = Not Supported, X = Number of sectors in per group 48h 90h 0001h Sector Temporary Unprotect 00 = Not Supported, 01 = Supported 49h 92h 0004h Sector Protect/Unprotect scheme 04 = 29LV800 mode 4Ah 94h 0000h Simultaneous Operation 00 = Not Supported 4Bh 96h 0000h Burst Mode Type 00 = Not Supported, 01 = Supported 4Ch 98h 0000h Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page 4Dh 9Ah 00B5h 4Eh 9Ch 00C5h 4Fh 9Eh 000Xh ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Top/Bottom Boot Sector Flag 02h = Bottom Boot Device, 03h = Top Boot Device Am29LV320D November 15, 2004 COMMAND DEFINITIONS Writing specific address and data commands or sequences into the command register initiates device operations. Table 14, on page 29 defines the valid register command sequences. Note that writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. A reset command is required to return the device to normal operation. quence before programming begins. This resets the device to which the system was writing to the read mode. If the program command sequence is written to a sector that is in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. Once programming begins, however, the device ignores reset commands until the operation is complete. All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE# or CE#, whichever happens first. Refer to the AC Characteristics section for timing diagrams. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. Reading Array Data The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after which the system can read data from any non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See “Erase Suspend/Erase Resume Commands” on page 28 for more information. The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See the next section, “Reset Command, for more information. See also “Requirements for Reading Array Data” on page 11 for more information. The Read-Only Operations table provides the read parameters, and Figure 14, on page 38 shows the timing diagram. Reset Command Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to which the system was writing to the read mode. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command seNovember 15, 2004 If DQ5 goes high during a program or erase operation, writing the reset command returns the d e v i c e t o t h e r e a d m o d e ( o r e ra s e - s u s pend-read mode if the device was in Erase Suspend). Autoselect Command Sequence The autoselect command sequence allows the host system to read several identifier codes at specific addresses: Table 13. Autoselect Codes Identifier Code Address Manufacturer ID 00h Device ID 01h SecSi Sector Factory Protect 03h Sector Group Protect Verify (SA)02h Table 14, on page 29 shows the address and data requirements. This method is an alternative to that shown in Table 6, on page 16, which is intended for PROM programmers and requires VID on address pin A9. The autoselect command sequence may be written to an address within sector that is either in the read or erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the autoselect command. The device then enters the autoselect mode. The system may read at any address any number of times without initiating another autoselect command sequence. The system must write the reset command to r e t u r n t o t h e r e a d m o d e ( o r e ra s e - s u s pend-read mode if the device was previously in Erase Suspend). Am29LV320D 25 Enter SecSiTM Sector/Exit SecSi Sector Command Sequence The SecSi Sector region provides a secured data area containing a random, sixteen-byte electronic serial number (ESN). The system can access the SecSi Sector region by issuing the three-cycle Enter SecSi Sector command sequence. The device continues to access the SecSi Sector region until the system issues the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command sequence returns the device to normal operation. Table 14, on page 29 shows the address and data requirem ents for both comm and sequences. Note that the ACC function and unlock bypass modes are not available when the device enters the SecSi Sector. See also “SecSiTM Sector (Secured Silicon) Flash Memory Region” on page 20 for further information. Byte/Word Program Command Sequence The system may program the device by word or byte, depending on the state of the BYTE# pin. Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Table 14, on page 29 shows the address and data requirements for the byte program command sequence. Note that the autoselect, SecSi Sector, and CFI modes are unavailable while a programming operation is in progress. When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to “Write Operation Status” on page 30 for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device returns to the read mode, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from “0” back to a “1.” At- 26 tempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read shows that the data is still “0.” Only erase operations can convert a “0” to a “1.” Unlock Bypass Command Sequence The unlock bypass feature allows the system to program bytes or words to the device faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Table 14, on page 29 shows the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data 90h. The second cycle need only contain the data 00h. The device then re turns to the read mode. The device offers accelerated program operations through the WP#/ACC pin. When the system asserts V H H on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass prog ram comm and sequence. The device uses the higher voltage on the WP#/ACC pin to accelerate the operation. Note that the WP#/ACC pin must not be at VHH any operation other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Figure 4, on page 27 illustrates the algorithm for the program operation. Refer to the table “Erase and Program Operations” on page 41 for parameters, and Figure 18, on page 42 for timing diagrams. Am29LV320D November 15, 2004 When the Embedded Erase algorithm is complete, the device returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/BY#. Refer to “Write Operation Status” on page 30 for information on these status bits. START Write Program Command Sequence Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once the device returns to reading array data, to ensure data integrity. Data Poll from System Embedded Program algorithm in progress Verify Data? No Yes Increment Address No Sector Erase Command Sequence Last Address? Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the sector erase command. Table 14, on page 29 shows the address and data requirements for the sector erase command sequence. Note that the autoselect, SecSi Sector, and CFI modes are unavailable while an erase operation is in progress. Yes Programming Completed Note: See Table 14, on page 29 for program command sequence. Figure 4. Program Operation Chip Erase Command Sequence Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or tim ing s during the se operatio ns. Table 14, on page 29 shows the address and data requirements for the chip erase command sequence. Note that the autoselect, SecSi Sector, and CFI modes are unavailable while an erase operation is in progress. November 15, 2004 Figure 5, on page 28 illustrates the algorithm for the erase operation. Refer to table “Erase and Program Operations” on page 41 for parameters, and Figure 19, on page 43 section for timing diagrams. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of 50 µs occurs. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise the last address and command may not be accepted, and erasure may begin. It is recommended that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. Any command other than Sector Erase or Erase Suspend during the Am29LV320D 27 time-out period resets the device to the read mode. The system must rewrite the command sequence and any additional addresses and commands. The system can monitor DQ3 to determine if the sector erase timer timed out (See the section “DQ3: Sector Erase Timer” on page 32.). The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by reading DQ7, DQ6, DQ2, or RY/BY# in the erasing sector. Refer to “Write Operation Status” on page 30 for information on these status bits. Once the sector erase operation begins, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once the device returns to reading array data, to ensure data integrity. pended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to the “Write Operation Status” on page 30 section for information on these status bits. After an erase-suspended program operation is complete, the device returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard Byte Program operation. Refer to “Write Operation Status” on page 30 for more information. In the erase-suspend-read mode, the system can also issue the autoselect command sequence. Refer to “Autoselect Mode” on page 16 an d “A uto se le ct C om m a nd Se qu en ce” on page 25 for details. To resume the sector erase operation, the system must write the Erase Resume command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip resumes erasing. Figure 5, on page 28 illustrates the algorithm for the erase operation. Refer to table “Erase and Program Operations” on page 41 for parameters, and Figure 19, on page 43 for timing diagrams. START Write Erase Command Sequence (Notes 1, 2) Erase Suspend/Erase Resume Commands The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of 20 µs to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation is suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at any address within erase-sus28 Data Poll to Erasing Bank from System Embedded Erase algorithm in progress No Data = FFh? Yes Erasure Completed Notes: 1. See Table 14, on page 29 for erase command sequence. 2. See the section on DQ3 for information on the sector erase timer. Am29LV320D Figure 5. Erase Operation November 15, 2004 Command Definitions Table 14. Cycles Command Sequence (Note 1) Am29LV320D Command Definitions Bus Cycles (Notes 2–5) First Second Addr Data Addr Data Read (Note 6) 1 RA RD Reset (Note 7) 1 XXX F0 Autoselect (Note 8) Manufacturer ID Device ID SecSi Sector Factory Protect (Note 9) Sector Protect Verify (Note 10) Enter SecSi™ Sector Region Exit SecSi Sector Region Program Unlock Bypass Word Byte Word Byte 4 4 Word Byte 555 AAA 555 AAA AAA 4 Word Byte Word Byte Word Byte 4 4 3 555 2AA 555 555 AA 555 AAA 555 AAA 555 AAA 555 AAA 55 55 AA AA AA 2AA 555 2AA 555 2AA 555 2AA 555 55 55 55 55 XXX A0 PA PD Unlock Bypass Reset (Note 12) 2 XXX 90 XXX 00 Chip Erase Sector Erase Byte Word Byte 6 6 AAA 555 AAA AA AA Erase Suspend (Note 13) 1 XXX B0 Erase Resume (Note 14) 1 XXX 30 CFI Query (Note 15) Word Byte 1 55 AA 2AA 555 2AA 555 Notes: 1. See Table 1 for description of bus operations. 4. 5. 6. 7. 8. 9. All values are in hexadecimal. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles. Data bits DQ15–DQ8 are don’t care in command sequences, except for RD and PD. Unless otherwise noted, address bits A20–A11 are don’t cares. No unlock or command cycles required when device is in read mode. The Reset command is required to return to the read mode (or to the erase-suspend-read mode if previously in Erase Suspend) when a device is in the autoselect mode, or if DQ5 goes high (while the device is providing status information). The fourth cycle of the autoselect command sequence is a read cycle. Data bits DQ15–DQ8 are don’t care. See the Autoselect Command Sequence section for more information. The data is 99h for factory locked and 19h for not factory locked. November 15, 2004 90 X00 01 X01 (see Table 6) 90 55 55 555 555 AAA 555 AAA 555 AAA 555 AAA 555 AAA Sixth X03 90 90 AAA X02 Fifth Addr Data Addr Data X06 (SA)X0 2 (SA)X0 4 99/19 00/01 88 90 XXX 00 A0 PA PD 20 80 80 555 AAA 555 AAA AA AA 2AA 555 2AA 555 55 55 555 AAA SA 10 30 98 Legend: X = Don’t care RA = Address of the memory location to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. 2. 3. Data AAA 2 555 AAA 55 Unlock Bypass Program (Note 11) Word 555 AAA Addr 555 555 AA 555 AAA Fourth Data 555 55 2AA AAA 3 2AA 2AA AA 555 Byte Byte AA 555 4 Word Word AA Third Addr PD = Data to be programmed at location PA. Data latches on the rising edge of WE# or CE# pulse, whichever happens first. SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A20–A12 uniquely select any sector. 10. The data is 00h for an unprotected sector and 01h for a protected sector. 11. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 12. The Unlock Bypass Reset command is required to return to the read mode when the device is in the unlock bypass mode. 13. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 14. The Erase Resume command is valid only during the Erase Suspend mode. 15. Command is valid when device is ready to read array data or when device is in autoselect mode. Am29LV320D 29 WRITE OPERATION STATUS The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 15, on page 33 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an Embedded Program or Erase operation is in progress or is completed. DQ7: Data# Polling when the system samples the DQ7 output, it may read the status or valid data. Even if the device completes the program or erase operation and DQ7 contains valid data, the data outputs on DQ0–DQ6 may be still invalid. Valid data on DQ0–DQ7 appears on successive read cycles. Table 15, on page 33 shows the outputs for Data# Polling on DQ7. Figure 6, on page 30 shows the Data# Polling algorithm. Figure 20, on page 44 in the AC Characteristics section shows the Data# Polling timing diagram. The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether a device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. START Read DQ7–DQ0 Addr = VA During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to the read mode. DQ7 = Data? No No During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the device returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on 30 Yes DQ5 = 1? Yes Read DQ7–DQ0 Addr = VA DQ7 = Data? Yes No FAIL PASS Notes: 1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid address is any non-protected sector address. 2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5. Am29LV320D Figure 6. Data# Polling Algorithm November 15, 2004 RY/BY#: Ready/Busy# The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/ B Y# is an o p e n-d rai n o ut p ut , se ve ral RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is in the r e a d m o d e , th e s ta n d b y m o d e , o r i n th e e ra s e - s u s p e n d - r e a d m o d e . Ta b l e 1 5 , o n page 33 shows the outputs for RY/BY#. D Q 6 a l s o t o g g l e s d u r i n g t h e e ra s e - s u s pend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table 15, on page 33 shows the outputs for Toggle Bit I on DQ6. Figure 7, on page 31 shows the toggle bit algorithm. Figure 21, on page 45 in the “AC Characteristics” section shows the toggle bit timing diagrams. Figure 22, on page 45 shows the differences between DQ2 and DQ6 in graphical form. See also the subsection on DQ2: Toggle Bit II. START DQ6: Toggle Bit I Read DQ7–DQ0 Toggle Bit I on DQ6 indicates whether an Emb ed d ed P r o gram or Era s e a lg or ith m i s in progress or complete, or whether the device entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. Read DQ7–DQ0 Toggle Bit = Toggle? During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, DQ6 stops toggling. Yes No After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on “DQ7: Data# Polling” on page 30). If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is written, then returns to reading array data. DQ5 = 1? Yes Read DQ7–DQ0 Twice Toggle Bit = Toggle? No Yes Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Note: The system should recheck the toggle bit even if DQ5 = “1” because the toggle bit may stop toggling as DQ5 changes to “1.” See the subsections on DQ6 and DQ2 for more information. Figure 7. November 15, 2004 No Am29LV320D Toggle Bit Algorithm 31 DQ2: Toggle Bit II The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that were selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 15, on page 33 to compare outputs for DQ2 and DQ6. Figure 7, on page 31 shows the toggle bit algorithm in flowchart form, and the section “DQ2: Toggle Bit II” on page 32 explains the algorithm. See also the DQ6: Toggle Bit I subsection. Figure 21, on page 45 shows the toggle bit timing diagram. Figure 22, on page 45 shows the differences b etween DQ2 and DQ 6 in graphical form. Reading Toggle Bits DQ6/DQ2 Refer to Figure 7, on page 31 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must 32 write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 7, on page 31). DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase cycle was not successfully completed. The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was previously programmed to “0.” Only an erase operation can change a “0” back to a “1.” Under this condition, the device halts the operation, and when the timing limit is exceeded, DQ5 produces a “1.” Under both these conditions, the system must write the reset command to return to the read mode (or to the erase-suspend-read mode if the device was previously in the erase-suspend-program mode). DQ3: Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure started. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also app l i e s a f t e r e a c h a d d i t i o n a l s e c t o r e ra s e command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. See also the Sector Erase Command Sequence section. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device accepted the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase algorithm started; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the Am29LV320D November 15, 2004 device accepts additional sector erase commands. To ensure the command is accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the Table 15. Standard Mode Erase Suspend Mode Status Embedded Program Algorithm Embedded Erase Algorithm Erase Erase-Suspend-R Suspended Sector ead Non-Erase Suspended Sector Erase-Suspend-Program second status check, the last command might not have been accepted. Table 15, on page 33 shows the status of DQ3 relative to the other status bits. Write Operation Status DQ7 (Note 2) DQ6 DQ5 (Note 1) DQ3 DQ2 (Note 2) RY/BY# DQ7# Toggle 0 N/A No toggle 0 0 Toggle 0 1 Toggle 0 1 No toggle 0 N/A Toggle 1 Data Data Data Data Data 1 DQ7# Toggle 0 N/A N/A 0 Notes: 1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation exceeds the maximum timing limits. Refer to the section on DQ5 for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. November 15, 2004 Am29LV320D 33 ABSOLUTE MAXIMUM RATINGS Storage Temperature Plastic Packages. . . . . . . . . . –65°C to +150°C Ambient Temperature with Power Applied. . . . . . . . –65°C to +125°C Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . –0.5 V to +4.0 V A9, OE#, RESET#, and WP#/ACC (Note 2). . –0.5 V to +12.5 V All other pins (Note 1) –0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) . 200 mA Notes: 1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to –2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. See Figure 8, on page 34. During v o l ta g e tr a n s i ti o n s , i n pu t o r I / O pi n s m a y overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 9, on page 34. 20 ns +0.8 VSS–0.5 VSS–2.0 2. Minimum DC input voltage on pins A9, OE#, RESET#, and WP#/ACC is –0.5 V. During voltage transitions, A9, OE#, WP#/ACC, and RESET# may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 8, on page 34. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns. Maximum DC input voltage on WP#/ACC is +9.5 V which may overshoot to +12.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. 20 ns 20 ns Figure 8. Maximum Negative Overshoot Waveform 20 ns VCC+2.0 VCC+0.5 S t r e s s es a b o v e t h o s e l i s t e d u n d er “A bs o l u t e Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional o peration of th e device at these or any o ther conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. 2.0 V 20 ns 20 ns Figure 9. Maximum Positive Overshoot Waveform OPERATING RANGES Industrial (I) Devices Ambient Temperature (TA). . . . –40°C to +85°C VCC Supply Voltages VCC for all devices . . . . . . . . . . 2.7 V to 3.6 V Operating ranges define those limits between which the functionality of the device is guaranteed. 34 Am29LV320D November 15, 2004 DC CHARACTERISTICS CMOS Compatible Paramet er Symbol Parameter Description Test Conditions Min Typ Max Unit ±3.0 µA ILI Input Load Current VIN = VSS to VCC, VCC = VCC max ILIT A9 Input Load Current VCC = VCC max; A9 = 12.5 V 35 µA ILR RESET# Input Load Current VCC = VCC max; RESET# = 12.5 V 35 µA Output Leakage Current VOUT = VSS to VCC, VCC = VCC max ±1.0 µA ILO ICC1 VCC Active Read Current (Notes 1, 2) CE# = VIL, OE# Byte Mode = CE# = VIL, OE# Word Mode = VIH, VIH, 5 MHz 10 16 1 MHz 2 4 5 MHz 10 16 2 4 15 30 mA CE#, RESET# = VCC ± 0.3 V 0.2 5 µA VCC Reset Current (Note 2) RESET# = VSS ± 0.3 V 0.2 5 µA ICC5 Automatic Sleep Mode (Notes 2, 4) VIH = VCC ± 0.3 V; VIL = VSS ± 0.3 V 0.2 5 µA ICC2 VCC Active Write Current (Notes 2, 3) CE# = VIL, OE# ICC3 VCC Standby Current (Note 2) ICC4 1 MHz mA = VIH, WE# = VIL VIL Input Low Voltage –0.5 0.8 V VIH Input High Voltage 0.7 x VCC VCC + 0.3 V VHH Voltage for WP#/ACC Sector Protect/Unprotect and Program Acceleration VCC = 3.0 V ± 10% 11.5 12.5 V VID Voltage for Autoselect and Temporary Sector Unprotect VCC = 3.0 V ± 10% 11.5 12.5 V VOL Output Low Voltage VOH1 VOH2 VLKO Output High Voltage IOL = 4.0 mA, VCC = VCC min 0.45 IOH = –2.0 mA, VCC = VCC min 0.85 VCC IOH = –100 µA, VCC = VCC min VCC–0.4 Low VCC Lock-Out Voltage (Note 5) 2.3 V V 2.5 V Notes: 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. 2. Maximum ICC specifications are tested with VCC = VCCmax. 3. ICC active while Embedded Erase or Embedded Program is in progress. 4. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is 200 nA. 5. Not 100% tested. November 15, 2004 Am29LV320D 35 DC CHARACTERISTICS Zero-Power Flash 25 Supply Current in mA 20 15 10 5 0 0 500 1000 1500 2000 2500 3000 3500 4000 Time in ns Note: Addresses are switching at 1 MHz Figure 10. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) 12 3.6 V 10 2.7 V Supply Current in mA 8 6 4 2 0 1 2 4 5 Frequency in MHz Note: T = 25 °C Figure 11. 36 3 Typical ICC1 vs. Frequency Am29LV320D November 15, 2004 TEST CONDITIONS Table 16. 3.3 V Test Condition 90 Output Load 2.7 kΩ Device Under Test Test Specifications 100 pF 5 ns 0.0–3.0 V Input timing measurement reference levels 1.5 V Output timing measurement reference levels 1.5 V Input Pulse Levels Note: Diodes are IN3064 or equivalent Figure 12. 30 Input Rise and Fall Times 6.2 kΩ Unit 1 TTL gate Output Load Capacitance, CL (including jig capacitance) CL 120 Test Setup Key To Switching Waveforms WAVEFORM INPUTS OUTPUTS Steady Changing from H to L Changing from L to H 3.0 V Input Don’t Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is High Impedance State (High Z) 1.5 V Measurement Level 1.5 V Output 0.0 V Figure 13. November 15, 2004 Input Waveforms and Measurement Levels Am29LV320D 37 AC CHARACTERISTICS Read-Only Operations Speed Options Parameter JEDEC Std. Description Test Setup 90 120 Unit tAVAV tRC Read Cycle Time (Note 1) Min 90 120 ns tAVQV tACC Address to Output Delay CE#, OE# = VIL Max 90 120 ns tELQV tCE Chip Enable to Output Delay OE# = VIL Max 90 120 ns tGLQV tOE Output Enable to Output Delay Max 40 50 ns tEHQZ tDF Chip Enable to Output High Z (Note 1) Max 16 ns tGHQZ tDF Output Enable to Output High Z (Note 1) Max 16 ns tAXQX tOH Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First Min 0 ns Read Output Enable Hold Time Toggle and (Note 1) Data# Polling Min 0 ns tOEH Min 10 ns Notes: 1. Not 100% tested. 2. See Figure 12, on page 37 and Table 16, on page 37 for test specifications. tRC Addresses Stable Addresses tACC CE# tRH tRH tDF tOE OE# tOEH WE# tCE tOH HIGH Z HIGH Z Output Valid Outputs RESET# RY/BY# 0V Figure 14. 38 Read Operation Timings Am29LV320D November 15, 2004 AC CHARACTERISTICS Hardware Reset (RESET#) Parameter JEDEC Std Description All Speed Options Unit tReady RESET# Pin Low (During Embedded Algorithms) to Read Mode (See Note) Max 20 µs tReady RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode (See Note) Max 500 ns tRP RESET# Pulse Width Min 500 ns tRH Reset High Time Before Read (See Note) Min 50 ns tRPD RESET# Low to Standby Mode Min 20 µs tRB RY/BY# Recovery Time Min 0 ns Note: Not 100% tested. RY/BY# CE#, OE# tRH RESET# tRP tReady Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms tReady RY/BY# tRB CE#, OE# tRH RESET# tRP Figure 15. November 15, 2004 Reset Timings Am29LV320D 39 AC CHARACTERISTICS Word/Byte Configuration (BYTE#) Parameter JEDEC Std. Description 90 120 Unit tELFL/tELFH CE# to BYTE# Switching Low or High Max 5 ns tFLQZ BYTE# Switching Low to Output HIGH Z Max 16 ns tFHQV BYTE# Switching High to Output Active Min 90 120 ns CE# OE# BYTE# BYTE# Switchin g from word to byte mode DQ0–DQ14 tELFL Data Output (DQ0–DQ14) DQ15 Output DQ15/A-1 Data Output Address Input tFLQZ tELFH BYTE# BYTE# Switchin g from byte to word mode DQ0–DQ14 Data Output DQ15/A-1 Address Input Data Output (DQ0–DQ14) DQ15 Output tFHQ Figure 16. BYTE# Timings for Read Operations CE# The falling edge of the last WE# WE# BYTE# tSET (tAS) tHOLD (tAH) Note: Refer to the Erase/Program Operations table for tAS and tAH specifications. Figure 17. 40 BYTE# Timings for Write Operations Am29LV320D November 15, 2004 AC CHARACTERISTICS Erase and Program Operations Parameter JEDEC Std. tAVAV tWC Write Cycle Time (Note 1) Min tAVWL tAS Address Setup Time Min 0 ns tASO Address Setup Time to OE# low during toggle bit polling Min 15 ns tAH Address Hold Time Min tAHT Address Hold Time From CE# or OE# high during toggle bit polling Min tDVWH tDS Data Setup Time Min tWHDX tDH Data Hold Time Min 0 ns tOEPH Output Enable High during toggle bit polling Min 20 ns tGHWL tGHWL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tELWL tCS CE# Setup Time Min 0 ns tWHEH tCH CE# Hold Time Min 0 ns tWLWH tWP Write Pulse Width Min tWHDL tWPH Write Pulse Width High Min 30 ns tSR/W Latency Between Read and Write Operations Min 0 ns Byte Typ 9 Word Typ 11 Accelerated Programming Operation, Word or Byte (Note 2) Typ 7 µs Sector Erase Operation (Note 2) Typ 0.7 sec tVCS VCC Setup Time (Note 1) Min 50 µs tRB Write Recovery Time from RY/BY# Min 0 ns Program/Erase Valid to RY/BY# Delay Max 90 ns tWLAX tWHWH1 tWHWH1 tWHWH2 tWHWH1 tWHWH1 tWHWH2 tBUSY Description Programming Operation (Note 2) 90 120 Unit 90 120 ns 45 50 0 45 ns 50 35 ns 50 ns ns µs Notes: 1. Not 100% tested. 2. See “Erase And Programming Performance” on page 50 for more information. November 15, 2004 Am29LV320D 41 AC CHARACTERISTICS Program Command Sequence (last two cycles) tAS tWC Addresses 555h Read Status Data (last two cycles) PA PA PA tAH CE# tCH OE# tWHWH1 tWP WE# tWPH tCS tDS tDH A0h Data PD Status tBUSY DOUT tRB RY/BY# tVCS VCC Notes: 1. PA = program address, PD = program data, DOUT is the true data at the program address. 2. Illustration shows device in word mode. Figure 18. 42 Program Operation Timings Am29LV320D November 15, 2004 AC CHARACTERISTICS Erase Command Sequence (last two cycles) tAS tWC 2AAh Addresses Read Status Data VA SA VA 555h for chip erase tAH CE# tCH OE# tWP WE# tWPH tCS tWHWH2 tDS tDH Data 55h In Progress 30h Complete 10 for Chip Erase tBUSY tRB RY/BY# tVCS VCC Notes: 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status” on page 30). 2. These waveforms are for the word mode. Figure 19. November 15, 2004 Chip/Sector Erase Operation Timings Am29LV320D 43 AC CHARACTERISTICS tRC Addresses VA VA VA tACC tCE CE# tCH tOE OE# tOEH tDF WE# tOH High Z DQ7 Complement Complement Status Data Status Data True Valid Data High Z DQ0–DQ6 True Valid Data tBUSY RY/BY# Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. Figure 20. 44 Data# Polling Timings (During Embedded Algorithms) Am29LV320D November 15, 2004 AC CHARACTERISTICS tAHT tAS Addresses tAHT tASO CE# tCEPH tOEH WE# tOEPH OE# tDH DQ6/DQ2 tOE Valid Data Valid Status Valid Status Valid Status (first read) (second read) (stops toggling) Valid Data RY/BY# Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle Figure 21. Enter Embedded Erasing WE# Toggle Bit Timings (During Embedded Algorithms) Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Program Erase Suspend Read Erase Resume Erase Suspend Read Erase Erase Complete DQ6 DQ2 Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6. Figure 22. November 15, 2004 DQ2 vs. DQ6 Am29LV320D 45 AC CHARACTERISTICS Temporary Sector Unprotect Parameter JEDEC Std. Description All Speed Options Unit tVIDR VID Rise and Fall Time (See Note) Min 500 ns tVHH VHH Rise and Fall Time (See Note) Min 250 ns tRSP RESET# Setup Time for Temporary Sector Unprotect Min 4 µs tRRB RESET# Hold Time from RY/BY# High for Temporary Sector Unprotect Min 4 µs Note: Not 100% tested. VID RESET# VID VSS, VIL, or VIH VSS, VIL, or VIH tVIDR tVIDR Program or Erase Command Sequence CE# WE# tRRB tRSP RY/BY# Figure 23. Temporary Sector Unprotect Timing Diagram VHH WP#/ACC VIL or VIH VIL or VIH tVHH Figure 24. 46 tVHH Accelerated Program Timing Diagram Am29LV320D November 15, 2004 AC CHARACTERISTICS VID VIH RESET# SA, A6, A1, A0 Valid* Valid* Sector/Sector Block Protect or Unprotect Data 60h 60h Valid* Verify 40h Status Sector/Sector Block Protect: 150 µs, Sector/Sector Block Unprotect: 15 ms 1 µs CE# WE# OE# * For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0. Figure 25. Sector/Sector Block Protect and Unprotect Timing Diagram November 15, 2004 Am29LV320D 47 AC CHARACTERISTICS Alternate CE# Controlled Erase and Program Operations Parameter JEDEC Std. tAVAV tWC Write Cycle Time (Note 1) Min tAVWL tAS Address Setup Time Min tELAX tAH Address Hold Time Min 45 50 ns tDVEH tDS Data Setup Time Min 45 50 ns tEHDX tDH Data Hold Time Min 0 ns tGHEL tGHEL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tWLEL tWS WE# Setup Time Min 0 ns tEHWH tWH WE# Hold Time Min 0 ns tELEH tCP CE# Pulse Width Min tEHEL tCPH CE# Pulse Width High Min 30 tWHWH1 tWHWH1 Programming Operation (Note 2) Byte Typ 9 Word Typ 11 tWHWH1 Accelerated Programming Operation, Word or Byte (Note 2) Typ 7 µs tWHWH2 Sector Erase Operation (Note 2) Typ 0.7 sec tWHWH1 tWHWH2 Description 90 120 Unit 90 120 ns 0 45 ns 50 ns ns µs Notes: 1. Not 100% tested. 2. See “Erase And Programming Performance” on page 50 for more information. 48 Am29LV320D November 15, 2004 AC CHARACTERISTICS 555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase Data# Polling Addresses PA tWC tAS tAH tWH WE# tGHEL OE# tWHWH1 or 2 tCP CE# tWS tCPH tBUSY tDS tDH DQ7# Data tRH A0 for program 55 for erase DOUT PD for program 30 for sector erase 10 for chip erase RESET# RY/BY# Notes: 1. Figure indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. 4. Waveforms are for the word mode. Figure 26. November 15, 2004 Alternate CE# Controlled Write (Erase/Program) Operation Timings Am29LV320D 49 ERASE AND PROGRAMMING PERFORMANCE Parameter Typ (Note 1) Max (Note 2) Sector Erase Time 0.7 Chip Erase Time 50 Unit Comments sec Excludes 00h programming prior to erasure (Note 4) 15 sec Byte Program Time 9 300 µs Word Program Time 11 360 µs 7 210 µs Byte Mode 36 108 Word Mode 24 72 Accelerated Byte/Word Program Time Chip Program Time (Note 3) Excludes system level overhead (Note 5) sec Notes: 1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally, programming typicals assume checkerboard pattern. 2. Under worst case conditions of 90°C, VCC = 2.7 V, 1,000,000 cycles. 3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes program faster than the maximum program times listed. 4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure. 5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 14, on page 29 for further information on command definitions. 6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles. LATCHUP CHARACTERISTICS Description Min Max Input voltage with respect to VSS on all pins except I/O pins (including A9, OE#, and RESET#) –1.0 V 12.5 V Input voltage with respect to VSS on all I/O pins –1.0 V VCC + 1.0 V –100 mA +100 mA VCC Current Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time. TSOP AND BGA PACKAGE CAPACITANCE Parameter Symbol Parameter Description CIN Input Capacitance VIN = 0 COUT Output Capacitance VOUT = 0 CIN2 Control Pin Capacitance Test Setup VIN = 0 Typ Max Unit TSOP 6 7.5 pF Fine-pitch BGA 4.2 5.0 pF pF TSOP 8.5 12 Fine-pitch BGA 5.4 6.5 pF TSOP 7.5 9 pF Fine-pitch BGA 3.9 4.7 pF Notes: 1. Sampled, not 100% tested. 2. Test conditions TA = 25°C, f = 1.0 MHz. DATA RETENTION Parameter Description Minimum Pattern Data Retention Time 50 Am29LV320D Test Conditions Min Unit 150°C 10 Years 125°C 20 Years November 15, 2004 PHYSICAL DIMENSIONS FBD048—48-ball Fine-Pitch Ball Grid Array (FBGA) 6 x 12 mm package Dwg rev AF; 1/2000 xFBD 048 6.00 mm x 12.00 mm PACKAGE 1.20 0.20 0.94 0.84 12.00 BSC 6.00 BSC 5.60 BSC 4.00 BSC 8 6 48 0.25 0.30 0.35 0.80 BSC 0.40 BSC November 15, 2004 Am29LV320D 51 PHYSICAL DIMENSIONS TS 048—48-Pin Standard TSOP Dwg rev AA; 10/99 52 Am29LV320D November 15, 2004 REVISION SUMMARY Revision A (November 1, 2000) Table 14, Am29LV320D Command Definitions Corrected autoselect codes for SecSi Sector Factory Protect. Initial release. Revision A+1 (January 23, 2001) Erase and Program Operations table Ordering Information Corrected FBGA part number table to include bottom boot part numbers. Revision A+2 (February 1, 2001) Corrected to indicate t BUSY specification is a maximum value. Revision B+1 (July 30, 2002) Figure 3, SecSi Sector Protect Verify Connection Diagrams Deleted fifth block in flowchart and modified text in fourth block. Corrected FBGA ball matrix. Revision A+3 (July 2, 2001) Revision C (October 25, 2002) Global Changed data sheet status from Advance Information to Preliminary. Table 3, Top Boot SecSiTM Sector Addresses Corrected sector block size for SA60–SA62 to 3x64. Sector/Sector Block Protection and Unprotection Distinctive Characteristics Changed endurance from “write” to “erase” cycles. Connection Diagrams Deleted ultrasonic reference and added package types to special package handling text. Ordering Information Noted that sectors are erased in parallel. SecSi Sector (Secured Silicon) Flash Memory Region TM Added commercial temperature range and removed extended temperature range. SecSi Sector Flash Memory Region Noted changes for upcoming versions of these devices: reduced SecSi Sector size, different ESN location for top boot devices, and deletion of SecSi Sector erase functionality. Current versions of these devices remain unaffected. Customer Lockable subsection: Deleted reference to alternate method of sector protection. Revision B (July 12, 2002) Autoselect, SecSi Sector, and CFI functions are not available during a program or erase operation. Global Deleted Preliminary status from document. Deleted burn-in option. Table 1, Am29LV320D Device Bus Operations In the legend, corrected VHH maximum voltage to 12.5 V. SecSiTM Sector (Secured Silicon) Flash Memory Region Added description of SecSi Sector protection verification. Clarified description of function. Noted the following: ACC and unlock bypass modes are not available when the SecSi Sector is enabled. Ordering Information Autoselect Command Sequence Command Definitions Writing incorrect data or commands may place the device in an unknown state. A reset command is then required. AC Characteristics Read-only Operations; Word/Byte Configuration: Changed t DF and t FLQZ to 16 ns for all speed options. DC Characteristics Deleted IACC and added ILR specifications from table. TSOP, SO, and BGA Package Capacitance Added BGA capacitance to table. November 15, 2004 Am29LV320D 53 Revision C+1 (February 16, 2003) Ordering Information Distinctive Characteristics Added Automotive In-Cabin temperature range and associated part numbers in the valid combination table. Added reference to MirrorBit in Secured Silicon section. Added Sector Architecture section. Erase and Programming Performance Updated Chip Erase Time SecSi Sector Flash Memory Region Referenced MirrorBit for an example in last sentence of first paragraph. Command Definitions Changed the first address of the Unlock Bypass Reset from BA to XXX. AC Characteristics Added tRH line to Figure 15. Erase and Program Operations Corrected Sector Erase Operation time t ( WHWH2) Alternate CE# Control Erase and Program Operations Corrected the Sector Erase Time Typical to 0.7. Corrected Sector Erase Operation time t ( WHWH2) Revision C+2 (April 4, 2003) Command Definitions Erase and Programming Performance Update text in Sector Erase Command Sequence paragraph. Distinctive Characteristics Clarified reference to MirrorBit in Secured Silicon section. SecSi Sector Flash Memory Region Clarified reference of MirrorBit for an example in last sentence of first paragraph. Revision C+3 (September 19, 2003) Valid Combinations Added the 90R package to table. Revision C+4 (April 5, 2004) Command Definitions Changed first address data for Erase Suspend/Resume from BA to XXX. Revision C+5 (June 4, 2004) Ordering Information Added Lead-free (Pb-free) options to the temperature ranges breakout table and valid combinations table. Product Selector Guide Added 90R voltage range. Revision C+6 (November 15, 2004) Global Added Colophon Updated Trademarks Added reference links 54 Am29LV320D November 15, 2004 Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion LLC will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks Copyright © 2000-2004 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc. ExpressFlash is a trademark of Advanced Micro Devices, Inc. Product names used in this publication are for identification purposes only and may be trademarks of their respective companies . November 15, 2004 Am29LV320D 55