Order this document by MMBT6520LT1/D SEMICONDUCTOR TECHNICAL DATA PNP Silicon COLLECTOR 3 Motorola Preferred Device 1 BASE 3 2 EMITTER 1 2 MAXIMUM RATINGS Rating Symbol Value Unit Collector–Emitter Voltage VCEO –350 Vdc Collector–Base Voltage VCBO –350 Vdc Emitter–Base Voltage CASE 318 – 08, STYLE 6 SOT– 23 (TO – 236AB) VEBO –5.0 Vdc Base Current IB –250 mA Collector Current — Continuous IC –500 mAdc DEVICE MARKING MMBT6520LT1 = 2Z THERMAL CHARACTERISTICS Characteristic Total Device Dissipation FR-5 Board (1) TA = 25°C Derate above 25°C Thermal Resistance, Junction to Ambient Total Device Dissipation Alumina Substrate, (2) TA = 25°C Derate above 25°C Thermal Resistance, Junction to Ambient Junction and Storage Temperature Symbol Max Unit PD 225 mW 1.8 mW/°C RθJA 556 °C/W PD 300 mW 2.4 mW/°C RθJA 417 °C/W TJ, Tstg – 55 to +150 °C ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) Characteristic Symbol Min Max Unit Collector–Emitter Breakdown Voltage (IC = –1.0 mA) V(BR)CEO –350 — Vdc Collector–Base Breakdown Voltage (IC = –100 µA) V(BR)CBO –350 — Vdc Emitter–Base Breakdown Voltage (IE = –10 µA) V(BR)EBO –5.0 — Vdc Collector Cutoff Current (VCB = –250 V) ICBO — –50 nA Emitter Cutoff Current (VEB = –4.0 V) IEBO — –50 nA OFF CHARACTERISTICS 1. FR–5 = 1.0 x 0.75 x 0.062 in. 2. Alumina = 0.4 x 0.3 x 0.024 in. 99.5% alumina Thermal Clad is a trademark of the Bergquist Company Preferred devices are Motorola recommended choices for future use and best overall value. Motorola Small–Signal Transistors, FETs and Diodes Device Data Motorola, Inc. 1996 1 MMBT6520LT1 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) (Continued) Characteristic Symbol Min Max 20 30 30 20 15 — — 200 200 — — — — — –0.30 –0.35 –0.50 –1.0 — — — –0.75 –0.85 –0.90 Unit ON CHARACTERISTICS DC Current Gain (IC = –1.0 mA, VCE = –10 V) (IC = –10 mA, VCE = –10 V) (IC = –30 mA, VCE = –10 V) (IC = –50 mA, VCE = –10 V) (IC = –100 mA, VCE = –10 V) hFE — Collector–Emitter Saturation Voltage (IC = –10 mA, IB = –1.0 mA) (IC = –20 mA, IB = –2.0 mA) (IC = –30 mA, IB = –3.0 mA) (IC = –50 mA, IB = –5.0 mA) VCE(sat) Vdc Base–Emitter Saturation Voltage (IC = –10 mA, IB = –1.0 mA) (IC = –20 mA, IB = –2.0 mA) (IC = –30 mA, IB = –3.0 mA) VBE(sat) Base–Emitter On Voltage (IC = –100 mA, VCE = –10 V) VBE(on) — –2.0 Vdc fT 40 200 MHz Collector–Base Capacitance (VCB= –20 V, f = 1.0 MHz) Ccb — 6.0 pF Emitter–Base Capacitance (VEB= –0.5 V, f = 1.0 MHz) Ceb — 100 pF Vdc SMALL–SIGNAL CHARACTERISTICS Current–Gain — Bandwidth Product (IC = –10 mA, VCE = –20 V, f = 20 MHz) 2 Motorola Small–Signal Transistors, FETs and Diodes Device Data hFE, DC CURRENT GAIN 200 VCE = 10 V TJ = 125°C 100 25°C 70 – 55°C 50 30 20 1.0 2.0 3.0 5.0 7.0 10 20 30 IC, COLLECTOR CURRENT (mA) 50 70 100 f T, CURRENT–GAIN — BANDWIDTH PRODUCT (MHz) MMBT6520LT1 100 70 50 20 10 1.0 1.4 TJ = 25°C V, VOLTAGE (VOLTS) 1.0 0.8 VBE(sat) @ IC/IB = 10 0.6 VBE(on) @ VCE = 10 V 2.5 IC IB 2.0 1.5 100 + 10 25°C to 125°C 1.0 0.5 0 – 1.5 VCE(sat) @ IC/IB = 10 2.0 VCE(sat) @ IC/IB = 5.0 3.0 5.0 7.0 10 20 30 50 70 100 IC, COLLECTOR CURRENT (mA) – 2.0 – 2.5 1.0 RθVC for VCE(sat) – 55°C to 25°C 100 70 50 2.0 1.0 k 700 500 TJ = 25°C Ceb 30 – 55°C to 125°C RθVB for VBE 3.0 5.0 7.0 10 20 30 IC, COLLECTOR CURRENT (mA) 50 70 100 Figure 4. Temperature Coefficients Figure 3. “On” Voltages td @ VBE(off) = 2.0 V 300 VCE(off) = 100 V IC/IB = 5.0 TJ = 25°C 200 20 t, TIME (ns) C, CAPACITANCE (pF) 50 70 – 1.0 0.2 10 7.0 5.0 Ccb tr 100 70 50 3.0 30 2.0 20 1.0 0.2 3.0 5.0 7.0 10 20 30 IC, COLLECTOR CURRENT (mA) – 0.5 0.4 0 1.0 2.0 Figure 2. Current–Gain — Bandwidth Product RθV, TEMPERATURE COEFFICIENTS (mV/°C) Figure 1. DC Current Gain 1.2 TJ = 25°C VCE = 20 V f = 20 MHz 30 0.5 1.0 2.0 5.0 10 20 VR, REVERSE VOLTAGE (VOLTS) 50 100 200 Figure 5. Capacitance Motorola Small–Signal Transistors, FETs and Diodes Device Data 10 1.0 2.0 3.0 5.0 7.0 10 20 30 IC, COLLECTOR CURRENT (mA) 50 70 100 Figure 6. Turn–On Time 3 MMBT6520LT1 10 k 7.0 k 5.0 k ts 3.0 k t, TIME (ns) 2.0 k 1.0 k 700 500 VCE(off) = 100 V IC/IB = 5.0 IB1 = IB2 TJ = 25°C tf 300 200 100 1.0 2.0 3.0 5.0 7.0 10 20 30 IC, COLLECTOR CURRENT (mA) 50 70 100 Figure 7. Turn–Off Time +VCC VCC ADJUSTED FOR VCE(off) = 100 V +10.8 V 2.2 k 20 k 50 Ω SAMPLING SCOPE 1.0 k 50 1/2MSD7000 –9.2 V PULSE WIDTH ≈ 100 µs tr, tf ≤ 5.0 ns DUTY CYCLE ≤ 1.0% FOR PNP TEST CIRCUIT, REVERSE ALL VOLTAGE POLARITIES APPROXIMATELY –1.35 V (ADJUST FOR V(BE)off = 2.0 V) r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) Figure 8. Switching Time Test Circuit 1.0 0.7 0.5 0.3 D = 0.5 0.2 0.2 0.1 0.1 0.07 0.05 SINGLE PULSE 0.05 SINGLE PULSE ZθJC(t) = r(t) • RθJC TJ(pk) – TC = P(pk) ZθJC(t) ZθJA(t) = r(t) • RθJA TJ(pk) – TA = P(pk) ZθJA(t) 0.03 0.02 0.01 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 t, TIME (ms) 100 200 500 1.0 k 2.0 k 5.0 k 10 k Figure 9. Thermal Response 4 Motorola Small–Signal Transistors, FETs and Diodes Device Data MMBT6520LT1 FIGURE A tP PP PP t1 1/f DUTY CYCLE + t1 f + ttP1 PEAK PULSE POWER = PP Design Note: Use of Transient Thermal Resistance Data Motorola Small–Signal Transistors, FETs and Diodes Device Data 5 MMBT6520LT1 INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection 0.037 0.95 0.037 0.95 0.079 2.0 0.035 0.9 0.031 0.8 inches mm SOT–23 SOT–23 POWER DISSIPATION The power dissipation of the SOT–23 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by T J(max), the maximum rated junction temperature of the die, RθJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA . Using the values provided on the data sheet for the SOT–23 package, PD can be calculated as follows: PD = TJ(max) – TA RθJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can calculate the power dissipation of the device which in this case is 225 milliwatts. PD = 150°C – 25°C 556°C/W = 225 milliwatts The 556°C/W for the SOT–23 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 225 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT–23 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. 6 SOLDERING PRECAUTIONS The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10°C. • The soldering temperature and time shall not exceed 260°C for more than 10 seconds. • When shifting from preheating to soldering, the maximum temperature gradient shall be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. Motorola Small–Signal Transistors, FETs and Diodes Device Data MMBT6520LT1 PACKAGE DIMENSIONS NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. A L 3 B S 1 V 2 G C D H K J CASE 318–08 ISSUE AE SOT–23 (TO–236AB) Motorola Small–Signal Transistors, FETs and Diodes Device Data DIM A B C D G H J K L S V INCHES MIN MAX 0.1102 0.1197 0.0472 0.0551 0.0350 0.0440 0.0150 0.0200 0.0701 0.0807 0.0005 0.0040 0.0034 0.0070 0.0180 0.0236 0.0350 0.0401 0.0830 0.0984 0.0177 0.0236 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.89 1.11 0.37 0.50 1.78 2.04 0.013 0.100 0.085 0.177 0.45 0.60 0.89 1.02 2.10 2.50 0.45 0.60 STYLE 6: PIN 1. BASE 2. EMITTER 3. COLLECTOR 7 MMBT6520LT1 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 8 ◊ *MMBT6520LT1/D* MMBT6520LT1/D Motorola Small–Signal Transistors, FETs and Diodes Device Data