ONSEMI MC1776CD

Order this document by MC1776C/D
This extremely versatile operational amplifier features low power
consumption and high input impedance. In addition, the quiescent currents
within the device may be programmed by the choice of an external resistor
value or current source applied to the Iset input. This allows the amplifier’s
characteristics to be optimized for input current and power consumption
despite wide variations in operating power supply voltages.
• ±1.2 V to ±18 V Operation
•
•
•
•
•
PROGRAMMABLE
OPERATIONAL AMPLIFIER
SEMICONDUCTOR
TECHNICAL DATA
Wide Programming Range
Offset Null Capability
No Frequency Compensation Required
Low Input Bias Currents
Short Circuit Protection
8
1
P1 SUFFIX
PLASTIC PACKAGE
CASE 626
Resistive Programming
(See Figure 1)
Rset to Ground
Rset to Negative Supply
(Recommended for supply voltage
less than ± 6.0 V)
7 VCC
2
2
–
3
6
3
+
8
Rset
4
VCC – 0.6
Rset
1
–
D SUFFIX
PLASTIC PACKAGE
CASE 751
(SO–8)
6
+
8
Rset
4
Iset =
VEE
8
7 VCC
VEE
Typical Rset Values
Iset =
VCC – 0.6 – VEE
Rset
Typical Rset Values
VCC, VEE
Iset = 1.5 µA
Iset = 15 µA
VCC, VEE
Iset = 1.5 µA
Iset = 15 µA
± 6.0 V
± 10 V
± 12 V
± 15 V
3.6 MΩ
6.2 MΩ
7.5 MΩ
10 MΩ
360 kΩ
620 kΩ
750 kΩ
1.0 MΩ
± 1.5 V
± 3.0 V
± 6.0 V
± 15 V
1.6 MΩ
3.6 MΩ
7.5 MΩ
20 MΩ
160 kΩ
360 kΩ
750 kΩ
2.0 MΩ
PIN CONNECTIONS
Offset Null
1
Invert
2
–
7
Noninvert
3
+
6
Output
VEE
4
5
Offset Null
Input
Active Programming
FET Current Source
2
3
7
–
2
VCC
6
+
4
Bipolar Current Source
VEE
8
3
6
+
4
8
VEE
Q
ORDERING INFORMATION
VB
Device
R
VEE
Pins not shown are not connected.
Operating
Temperature Range
MC1776CD
MC1776CP1
 Motorola, Inc. 1996
MOTOROLA ANALOG IC DEVICE DATA
Iset
VCC
(Top View)
7
–
VG
VEE
8
Package
SO–8
TA = 0° to +70°C
Plastic DIP
Rev 5
1
MC1776C
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Symbol
Value
Unit
Power Supply Voltages
VCC,VEE
±18
Vdc
Differential Input Voltage
VID
±30
Vdc
Rating
Common Mode Input Voltage
VCC and |VEE|
15 V
VCC and |VEE|
15 V
VICM
t
w
Vdc
VCC,VEE
±15
Voff–VEE
±0.5
Vdc
Programming Current
Iset
500
µA
Programming Voltage
(Voltage from Iset Terminal to Ground)
Vset
(VCC –2.0 V)
to VCC
Vdc
Output Short Circuit Duration (Note 1)
tSC
Indefinite
sec
Operating Temperature Range
TA
0 to +70
°C
Tstg
–65 to +150
°C
TJ
150
°C
Offset Null to VEE Voltage
Storage Temperature Range
Junction Temperature
NOTE 1. May be to ground or either supply voltage. Rating applies up to a case temperature of +125°C
or ambient temperature of +70°C and Iset ≤ 30 µA.
Representative Schematic Diagram
8
2
Inputs
3
Iset
7
–
VCC
50
+
2.0 k
100
6
100
30 pF
Output
100
1
Offset Null
5
50
10 k
10 k
4
Voltage Offset Null Circuit
2
–
8
Rset
Transient Response Test Circuit
2
7 VCC
6
+
3
1
4
3
7
6
4
Vin
VEE
VO
+
8
CL
RL
Rset
VEE
2
VCC
–
5
100 k
VEE
Pins not shown are
not connected.
MOTOROLA ANALOG IC DEVICE DATA
MC1776C
ELECTRICAL CHARACTERISTICS (VCC = +3.0 V, VEE = –3.0 V, Iset = 1.5 µA, TA = +25°C, unless otherwise noted.*)
Characteristic
Symbol
Input Offset Voltage (RS ≤ 10 kΩ)
TA = +25°C
Tlow* ≤ TA ≤ Thigh*
VIO
Offset Voltage Adjustment Range
VIOR
Input Offset Current
TA = +25°C
TA = Thigh
TA = Tlow
IIO
Input Bias Current
TA = +25°C
TA = Thigh
TA = Tlow
IIB
Min
Typ
Max
–
–
2.0
–
6.0
7.5
–
9.0
–
–
–
–
0.7
–
–
6.0
6.0
10
–
–
–
2.0
–
–
10
10
20
Unit
mV
mV
nA
nA
Input Resistance
ri
–
50
–
MΩ
Input Capacitance
ci
–
2.0
–
pF
+1.0
–
–
25 k
25 k
200 k
–
–
–
±2.0
±2.4
–
ro
–
5.0
–
kΩ
ISC
–
3.0
–
mA
70
86
–
–
25
200
–
–
13
–
20
25
–
–
78
–
120
150
tTLH
os
–
–
3.0
0
–
–
µs
%
SR
–
0.03
–
V/µs
Input Voltage Range
Tlow ≤ TA ≤ Thigh
Large Signal Voltage Gain
RL ≥ 75 kΩ, VO = ±1.0 V, TA = +25°C
RL ≥ 75 kΩ, VO = ±1.0 V, Tlow ≤ TA ≤ Thigh
Output Voltage Swing
RL ≥ 75 kΩ, Tlow ≤ TA ≤ Thigh
Output Resistance
Output Short Circuit Current
Common Mode Rejection
VID
AVOL
VO
Supply Current
TA = +25°C
Tlow ≤ TA ≤ Thigh
ICC, IEE
Power Dissipation
TA = +25°C
Tlow ≤ TA ≤ Thigh
PD
Slew Rate (RL ≥ 5.0 kΩ)
*Tlow = 0°C
V
dB
µV/V
PSRR
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
Transient Response (Unity Gain)
Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF
Rise Time
Overshoot
V/V
CMR
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
Supply Voltage Rejection Ratio
V
µA
µW
Thigh = +70°C
MOTOROLA ANALOG IC DEVICE DATA
3
MC1776C
ELECTRICAL CHARACTERISTICS (VCC = +3.0 V, VEE = –3.0 V, Iset = 15 µA, TA = +25°C, unless otherwise noted.*)
Characteristic
Symbol
Input Offset Voltage (RS ≤ 10 kΩ)
TA = +25°C
Tlow* ≤ TA ≤ Thigh*
VIO
Offset Voltage Adjustment Range
VIOR
Input Offset Current
TA = +25°C
TA = Thigh
TA = Tlow
IIO
Input Bias Current
TA = +25°C
TA = Thigh
TA = Tlow
IIB
Min
Typ
Max
–
–
2.0
–
6.0
7.5
–
18
–
–
–
–
2.0
–
–
25
25
40
–
–
–
15
–
–
50
50
100
Unit
mV
mV
nA
nA
Input Resistance
ri
–
5.0
–
MΩ
Input Capacitance
ci
–
2.0
–
pF
±1.0
–
–
25 k
25 k
200 k
–
–
–
±2.0
±2.1
–
ro
–
1.0
–
kΩ
ISC
–
5.0
–
mA
70
86
–
–
25
200
–
–
130
–
170
180
–
–
780
–
1020
1080
tTLH
os
–
–
0.6
5.0
–
–
µs
%
SR
–
0.35
–
V/µs
Input Voltage Range
Tlow ≤ TA ≤ Thigh
Large Signal Voltage Gain
RL ≥ 5.0 kΩ, VO = ±1.0 V, TA = +25°C
RL ≥ 5.0 kΩ, VO = ±1.0 V, Tlow ≤ TA ≤ Thigh
Output Voltage Swing
RL ≥ 5.0 kΩ, Tlow ≤ TA ≤ Thigh
Output Resistance
Output Short Circuit Current
VID
AVOL
VO
Common Mode Rejection
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
CMR
Supply Voltage Rejection Ratio
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
PSRR
Supply Current
TA = +25°C
Tlow ≤ TA ≤ Thigh
ICC, IEE
Power Dissipation
TA = +25°C
Tlow ≤ TA ≤ Thigh
PD
Transient Response (Unity Gain)
Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF
Rise Time
Overshoot
Slew Rate (RL ≥ 5.0 kΩ)
*Tlow = 0°C
4
V
V/V
V
dB
µV/V
µA
µW
Thigh = +70°C
MOTOROLA ANALOG IC DEVICE DATA
MC1776C
ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = –15 V, Iset = 1.5 µA, TA = +25°C, unless otherwise noted.*)
Characteristic
Symbol
Input Offset Voltage (RS ≤ 10 kΩ)
TA = +25°C
Tlow* ≤ TA ≤ Thigh*
VIO
Offset Voltage Adjustment Range
VIOR
Input Offset Current
TA = +25°C
TA = Thigh
TA = Tlow
IIO
Input Bias Current
TA = +25°C
TA = Thigh
TA = Tlow
IIB
Min
Typ
Max
–
–
2.0
–
6.0
7.5
–
9.0
–
–
–
–
0.7
–
–
6.0
6.0
10
–
–
–
2.0
–
–
10
10
20
Unit
mV
mV
nA
nA
Input Resistance
ri
–
50
–
MΩ
Input Capacitance
ci
–
2.0
–
pF
±10
–
–
50 k
50 k
400 k
–
–
–
±12
±10
±14
–
–
–
Input Voltage Range
Tlow ≤ TA ≤ Thigh
Large Signal Voltage Gain
RL ≥ 75 kΩ, VO = ±10 V, TA = +25°C
RL ≥ 75 kΩ, VO = ±10 V, Tlow ≤ TA ≤ Thigh
VID
V
AVOL
V/V
Output Voltage Swing
RL ≥ 75 kΩ, TA = +25°C
RL ≥ 75 kΩ, Tlow ≤ TA ≤ Thigh
VO
Output Resistance
ro
–
5.0
–
kΩ
ISC
–
3.0
–
mA
70
90
–
–
25
200
–
–
20
–
30
35
–
–
780
–
0.9
1.05
tTLH
os
–
–
1.6
0
–
–
µs
%
SR
–
0.1
–
V/µs
Output Short Circuit Current
Common Mode Rejection
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
CMR
Supply Voltage Rejection Ratio
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
PSRR
Supply Current
TA = +25°C
Tlow ≤ TA ≤ Thigh
ICC, IEE
Power Dissipation
TA = +25°C
Tlow ≤ TA ≤ Thigh
PD
Transient Response (Unity Gain)
Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF
Rise Time
Overshoot
Slew Rate (RL ≥ 5.0 kΩ)
*Tlow = 0°C
V
dB
µV/V
µA
mW
Thigh = +70°C
MOTOROLA ANALOG IC DEVICE DATA
5
MC1776C
ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = –15 V, Iset = 15 µA, TA = +25°C, unless otherwise noted.*)
Characteristic
Symbol
Input Offset Voltage (RS ≤ 10 kΩ)
TA = +25°C
Tlow* ≤ TA ≤ Thigh*
VIO
Offset Voltage Adjustment Range
VIOR
Input Offset Current
TA = +25°C
TA = Thigh
TA = Tlow
IIO
Input Bias Current
TA = +25°C
TA = Thigh
TA = Tlow
IIB
Min
Typ
Max
–
–
2.0
–
6.0
7.5
–
18
–
–
–
–
2.0
–
–
25
25
40
–
–
–
15
–
–
50
50
100
Unit
mV
mV
nA
nA
Input Resistance
ri
–
5.0
–
MΩ
Input Capacitance
ci
–
2.0
–
pF
±10
–
–
50 k
50 k
400 k
–
–
–
±10
±10
±13
–
–
–
Input Voltage Range
Tlow ≤ TA ≤ Thigh
Large Signal Voltage Gain
RL ≥ 5.0 kΩ, VO = ±10 V, TA = +25°C
RL ≥ 75 kΩ, VO = ±10 V, Tlow ≤ TA ≤ Thigh
VID
V
AVOL
V/V
Output Voltage Swing
RL ≥ 5.0 kΩ, TA = +25°C
RL ≥ 75 kΩ, Tlow ≤ TA ≤ Thigh
VO
Output Resistance
ro
–
1.0
–
kΩ
ISC
–
12
–
mA
70
90
–
–
25
200
–
–
160
–
190
200
–
–
–
–
5.7
6.0
tTLH
os
–
–
0.35
10
–
–
µs
%
SR
–
0.8
–
V/µs
Output Short Circuit Current
Common Mode Rejection
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
CMR
Supply Voltage Rejection Ratio
RS ≤ 10 kΩ, Tlow ≤ TA ≤ Thigh
PSRR
Supply Current
TA = +25°C
Tlow ≤ TA ≤ Thigh
ICC, IEE
Power Dissipation
TA = +25°C
Tlow ≤ TA ≤ Thigh
PD
Transient Response (Unity Gain)
Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF
Rise Time
Overshoot
Slew Rate (RL ≥ 5.0 kΩ)
*Tlow = 0°C
6
V
dB
µV/V
µA
µW
Thigh = +70°C
MOTOROLA ANALOG IC DEVICE DATA
MC1776C
Figure 2. Positive Standby Supply Current
versus Set Current
R set , SET RESISTOR ( Ω )
100 M
VCC = +15 V
VEE = –15 V
Rset to VEE
10 M
VCC = +3.0 V
VEE = –3.0 V
Rset to VEE
1.0 M
VCC = +15 V
VEE = –15 V
Rset to GND
VCC = +3.0 V
VEE = –3.0 V
Rset to GND
100 k
10 k
0.1
1.0
10
100
POSITIVE STANDBY SUPPLY CURRENT ( µA)
Figure 1. Set Current versus Set Resistor
1000
+3.0 V ≤ VCC ≤ +18 V
–3.0 V ≥ VEE ≥ –18 V
100
10
1.0
0.1
0.01
0.1
Figure 3. Open Loop Gain versus Set Current
VCC = +15 V
VEE = –15 V
RL = 75 k
I IB , INPUT BIAS CURRENT (nA)
A VOL, OPEN LOOP GAIN (V/M)
100
100
106
VCC = +3.0 V
VEE = –3.0 V
105
104
0.1
1.0
10
10
+3.0 V ≤ VCC ≤ +18 V
–3.0 V ≥ VEE ≥ –18 V
1.0
0.1
0.01
100
0.1
Iset, SET CURRENT (µA)
30
+3.0 V ≤ VCC ≤ +18 V
–3.0 V ≥ VEE ≥ –18 V
24
18
Iset = 1.5 µA
12
Iset = 1.5 µA
6.0
–40
–20
0
20
40
60 80
T, TEMPERATURE (°C)
MOTOROLA ANALOG IC DEVICE DATA
100
1.0
10
Iset, SET CURRENT (µA)
100
Figure 6. Gain Bandwidth Product
versus Set Current
GBW, GAIN BANDWIDTH PRODUCT (Hz)
Figure 5. Input Bias Current
versus Ambient Temperature
I IB , INPUT BIAS CURRENT (nA)
10
Figure 4. Input Bias Current versus Set Current
107
0
–60
1.0
Iset, SET CURRENT (µA)
Iset, SET CURRENT (µA)
120
140
10 M
1.0 M
VCC = +15 V
VEE = –15 V
VCC = +3.0 V
VEE = –3.0 V
100 k
10 k
1.0 k
0.1
1.0
10
100
Iset, SET CURRENT (µA)
7
MC1776C
Figure 8. Supply Current
versus Ambient Temperature
30
150
VCC = +15 V
VEE = –15 V
24 Iset = 15 µA
I S , SUPPLY CURRENT ( µA)
V O(pp), PEAK–TO–PEAK OUTPUT
VOLTAGE SWING (V)
Figure 7. Output Voltage Swing
versus Load Resistance
VCC = +15 V
VEE = –15 V
Iset = 1.5 µA
18
12
VCC = +3.0 V
VEE = –3.0 V
1.5 µA ≤ Iset ≤ 15 µA
6.0
0
1.0 k
10 k
100 k
120
90
60
30
RL, LOAD RESISTANCE (Ω)
–20
0
60
80
100
120 140
10
36
32
28
Iset = 15 µA
RL = 5.0 k
1.5 µA ≤ Iset ≤ 15 mA
RL = 75 k
24
20
SR, SLEW RATE (Vµ s)
VO,OUTPUT VOLTAGE SWING (V)
40
Figure 10. Slew Rate
versus Set Current
40
Iset = 1.5 µA
RL = 5.0 k
16
12
1.0
0.1
VCC = +15 V
VEE = –15 V
VCC = +3.0 V
VEE = –3.0 V
0.01
8.0
4.0
0
0
2.0
4.0
6.0
8.0
10
12
14
16
18
20
1.0
10
Iset, SET CURRENT (µA)
Figure 11. Input Noise Voltage
versus Set Current
Figure 12. Optimum Source Resistance for
Minimum Noise versus Set Current
10–14
f = 1.0 kHz
∆1 = Hz
+3.0 V ≤ VCC ≤ +18 V
–3.0 V ≥ VEE ≥ –18 V
10–16
10–17
0.01
0.1
VCC, (VEE), SUPPLY VOLTAGES (V)
10–13
10–15
0.001
0.01
OPTIMUM SOURCE RESISTANCE (M Ω )
V(RMS), MEAN SQUARE VOLTAGE(V 2/Hz)
20
T, AMBIENT TEMPERATURE (°C)
Figure 9. Output Voltage Swing
versus Supply Voltage
8
Iset = 1.5 µA
VCC = +3.0 V
VEE = –3.0 V
Iset = 1.5 µA
VCC = +15 V
VEE = –15 V
0
–60 –40
1.0 M
Iset = 15 µA
VCC = +3.0 V
VEE = –3.0 V
Iset = 1.5 µA
VCC = +15 V
VEE = –15 V
0.1
1.0
Iset, SET CURRENT (µA)
10
100
100
100
10
1.0
0.1
0.01
0.1
1.0
Iset, SET CURRENT (µA)
10
100
MOTOROLA ANALOG IC DEVICE DATA
MC1776C
Figure 13. Wien Bridge Oscillator
Figure 15. Multiple Feedback Bandpass Filter
(1.0 kHz)
22 k
C
200 k
10 k
+15 V
Input
3
6
MC1776C
8
4
Rset
C
1
fo =
2π RC
2.0 M
R1 = 160 k
R2 = 820
R5 = 300 k
C = 0.01 µF
for a 1.0 kHz filter
with Q = 10
and A (fo) = 1
R
R
8
4
–15 V
C
–15 V
(for fo = 1.0 kHz)
Figure 16. Gated Amplifier
R= 16 kΩ
C = 0.01 µF
1M
2
10 k
+15 V
7
–
6
MC1776C
+
Input
Vin
R1
C
2
3
+
4
For a given:
fo = center frequency
A (fo) = Gain at center frequency
Q = quality factor
VCC
15 V
270 k
MC1776C
R2
–15 V
2.7 M
7
–
4
8
10 k
VCC
R5
Output
3
Figure 14. Multiple Feedback Bandpass Filter
C
6
Output
+
R2
VO
+
7
–
MC1776C
–
3
+15 V
2
C
7
2
R5
R1
6
10 k
VO
Q
Gate
5.6 k
8
Rset
VEE
Choose a value for C, then
Q
R5 =
πfoC
R5
R1 =
2A (fo)
R1,R5
R2 =
4Q2 R1–R5
To obtain less than 10% error from the operational amplifier:
QO fo
≤ 0.1
GBW
where fo and GBW are expressed in Hz. GBW is available from
Figure 6 as a function of Set Current, Iset.
MOTOROLA ANALOG IC DEVICE DATA
Figure 17. High Input Impedance Amplifier
10 k
50 M
+15 V
500 k
Input
500 k
2
6
MC1776C
3
+
8
50 M
90 k
7
–
Output
4
–15 V
30 M
9
MC1776C
OUTLINE DIMENSIONS
P1 SUFFIX
PLASTIC PACKAGE
CASE 626–05
ISSUE K
8
5
–B–
1
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
4
F
–A–
NOTE 2
L
DIM
A
B
C
D
F
G
H
J
K
L
M
N
C
J
–T–
N
SEATING
PLANE
D
M
K
G
H
0.13 (0.005)
M
T A
M
B
MILLIMETERS
MIN
MAX
9.40
10.16
6.10
6.60
3.94
4.45
0.38
0.51
1.02
1.78
2.54 BSC
0.76
1.27
0.20
0.30
2.92
3.43
7.62 BSC
–––
10_
0.76
1.01
INCHES
MIN
MAX
0.370
0.400
0.240
0.260
0.155
0.175
0.015
0.020
0.040
0.070
0.100 BSC
0.030
0.050
0.008
0.012
0.115
0.135
0.300 BSC
–––
10_
0.030
0.040
M
D SUFFIX
PLASTIC PACKAGE
CASE 751–05
(SO–8)
ISSUE R
D
A
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. DIMENSIONS ARE IN MILLIMETERS.
3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.
C
8
5
0.25
H
E
M
B
M
1
4
h
B
e
X 45 _
q
A
C
SEATING
PLANE
L
0.10
A1
B
0.25
10
M
C B
S
A
S
DIM
A
A1
B
C
D
E
e
H
h
L
q
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.35
0.49
0.18
0.25
4.80
5.00
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.25
0_
7_
MOTOROLA ANALOG IC DEVICE DATA
MC1776C
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
MOTOROLA ANALOG IC DEVICE DATA
11
MC1776C
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
12
◊
*MC1776C/D*
MOTOROLA ANALOG IC DEVICE
DATA
MC1776C/D