SEMICONDUCTOR TECHNICAL DATA The MC10159 is a quad two channel multiplexer with enable. It incorporates common enable and common data select inputs. The select input determines which data inputs are enabled. A high (H) level enables data inputs D00, D10, D20, and D30. A low (L) level enables data inputs D01, D11, D21, and D31. Any change on the data inputs will be reflected at the outputs while the enable is low. Input levels are inverted at the output. L SUFFIX CERAMIC PACKAGE CASE 620–10 PD = 218 mW typ/pkg (No Load) tpd = 2.5 ns typ (Data to Q) 3.2 ns typ (Select to Q) tr, tf = 2.5 ns typ (20%–80%) P SUFFIX PLASTIC PACKAGE CASE 648–08 FN SUFFIX PLCC CASE 775–02 LOGIC DIAGRAM SELECT 9 D01 5 DIP PIN ASSIGNMENT 1 Q0 D00 6 D11 3 Q0 1 16 VCC Q1 2 15 Q2 D11 3 14 Q3 D10 4 13 D20 D01 5 12 D21 D00 6 11 D30 ENABLE 7 10 D31 VEE 8 9 SELECT 2 Q1 D10 4 ENABLE 7 D21 12 15 Q2 D20 13 Pin assignment is for Dual–in–Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6–11 of the Motorola MECL Data Book (DL122/D). D31 10 14 Q3 D30 11 TRUTH TABLE Enable Select D0 D1 Q L L X L H L L X H L L H L X H L H H X L H X X X L VCC = PIN 16 VEE = PIN 8 3/93 Motorola, Inc. 1996 3–65 REV 5 MC10159 ELECTRICAL CHARACTERISTICS Test Limits Characteristic Power Supply Drain Current Input Current Symbol Pin Pi Under Test IE 8 58 IinH 9 5 360 400 IinL 5 0.5 –30°C Min +25°C Max Min +85°C Max Unit 53 58 mAdc 225 250 225 250 µAdc Typ Max 42 Min 0.5 µAdc 0.3 Output Voltage Logic 1 VOH 1 –1.060 –0.890 –0.960 –0.810 –0.890 –0.700 Vdc Output Voltage Logic 0 VOL 1 –1.890 –1.675 –1.850 –1.650 –1.825 –1.615 Vdc Threshold Voltage Logic 1 VOHA 1 –1.080 Logic 0 VOLA 1 Threshold Voltage Switching Times Propagation Delay –0.980 –0.910 –1.655 Vdc –1.630 –1.595 (50Ω Load) Vdc ns Data Input Select Input Enable Input t5+1– t9+1– t7+1– 1 1 1 1.1 1.5 1.4 3.8 5.3 5.3 1.2 1.5 1.5 2.5 3.2 2.5 3.3 5.0 5.0 1.1 1.5 1.4 3.8 5.3 5.3 Rise Time (20 to 80%) t1+ 1 1.0 3.7 1.1 2.5 3.5 1.0 3.7 Fall Time (20 to 80%) t1– 1 1.0 3.7 1.1 2.5 3.5 1.0 3.7 ELECTRICAL CHARACTERISTICS (continued) TEST VOLTAGE VALUES (Volts) Characteristic Power Supply Drain Current Input Current @ Test Temperature VIHmax VILmin VIHAmin VILAmax VEE –30°C –0.890 –1.890 –1.205 –1.500 –5.2 +25°C –0.810 –1.850 –1.105 –1.475 –5.2 +85°C –0.700 –1.825 –1.035 –1.440 –5.2 Symbol Pin Under Test IE 8 IinH 9 5 IinL 5 TEST VOLTAGE APPLIED TO PINS LISTED BELOW VIHmax Logic 1 VOH 1 Logic 0 VOL 1 5 Threshold Voltage Logic 1 VOHA 1 9 Logic 0 VOLA 1 Propagation Delay (50Ω Load) (VCC) Gnd 8 16 8 8 16 16 8 16 8 16 8 16 6 8 16 8 16 Pulse In Pulse Out –3.2 V +2.0 V VILAmax 5 Output Voltage Switching Times VEE VIHAmin 9 5 Output Voltage Threshold Voltage VILmin 9 +1.11V 6 +0.31V Data Input Select Input Enable Input t5+1– t9+1– t7+1– 1 1 1 6 3, 12 5 9 7 1 1 1 8 8 16 16 Rise Time (20 to 80%) t1+ 1 9 5 1 8 16 Fall Time (20 to 80%) t1– 1 9 5 1 8 16 Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the same manner. MOTOROLA 3–66 MECL Data DL122 — Rev 6 MC10159 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 775–02 ISSUE C 0.007 (0.180) M T L–M B Y BRK –N– U N S 0.007 (0.180) M T L–M S S N S D –L– –M– Z W 20 D 1 V 0.010 (0.250) G1 X S T L–M S N S VIEW D–D A 0.007 (0.180) M T L–M S N S R 0.007 (0.180) M T L–M S N S Z C H –T– SEATING PLANE F VIEW S G1 0.010 (0.250) S T L–M S 0.007 (0.180) M T L–M S N S VIEW S S N S NOTES: 1. DATUMS –L–, –M–, AND –N– DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM –T–, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). MECL Data DL122 — Rev 6 N K 0.004 (0.100) J S K1 E G 0.007 (0.180) M T L–M 3–67 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 ––– 0.025 ––– 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 ––– 0.020 2_ 10 _ 0.310 0.330 0.040 ––– MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 ––– 0.64 ––– 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 ––– 0.50 2_ 10 _ 7.88 8.38 1.02 ––– MOTOROLA MC10159 OUTLINE DIMENSIONS L SUFFIX CERAMIC DIP PACKAGE CASE 620–10 ISSUE V –A– 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. –B– C L DIM A B C D E F G H K L M N –T– K N SEATING PLANE M E F J G D 16 PL 0.25 (0.010) 16 PL 0.25 (0.010) M T A T B M –A– 9 1 8 B F C L S –T– SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 ––– 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01 S P SUFFIX PLASTIC DIP PACKAGE CASE 648–08 ISSUE R 16 S INCHES MIN MAX 0.750 0.785 0.240 0.295 ––– 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 T A M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 Mfax: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 3–68 *MC10159/D* MC10159/D MECL Data DL122 — Rev 6