ADM1032 +15C Remote and Local System Temperature Monitor The ADM1032 is a dual−channel digital thermometer and under/overtemperature alarm intended for use in PCs and thermal management systems. The device can measure the temperature of a remote thermal diode, which can be located on the processor die or can be a discrete device (2N3904/06), accurate to 1°C. A novel measurement technique cancels out the absolute value of the transistor’s base emitter voltage so that no calibration is required. The ADM1032 also measures its ambient temperature. The ADM1032 communicates over a 2−wire serial interface compatible with System Management Bus (SMBus) standards. Under/overtemperature limits can be programmed into the device over the SMBus, and an ALERT output signals when the on−chip or remote temperature measurement is out of range. This output can be used as an interrupt or as a SMBus alert. The THERM output is a comparator output that allows CPU clock throttling or on/off control of a cooling fan. An ADM1032−1 and ADM1032−2 are available. The difference between the ADM1032 and the ADM1032−1 is the default value of the external THERM limit. The ADM1032−2 has a different SMBus address. The SMBus address of the ADM1032−2 is 0x4D. http://onsemi.com MARKING DIAGRAMS On−Chip and Remote Temperature Sensing Offset Registers for System Calibration 0.125°C Resolution/1°C Accuracy on Remote Channel 1°C Resolution/3°C Accuracy on Local Channel Fast (Up to 64 Measurements Per Second) 2−Wire SMBus Serial Interface Supports SMBus Alert Programmable Under/Overtemperature Limits Programmable Fault Queue Overtemperature Fail−Safe THERM Output Programmable THERM Limits Programmable THERM Hysteresis 170 mA Operating Current 5.5 mA Standby Current 3.0 V to 5.5 V Supply Small 8−Lead SOIC and MSOP Packages These are Pb−Free Devices 1 SOIC−8 CASE 751 Marking #1 # Y W XX December, 2009 − Rev. 11 Marking #2 = Pb−Free Package = Year = Work Week = Assembly Lot 8 T1x AYWG G MSOP−8 CASE 846AB 1 T1x = Refer to Order Info Table A = Assembly Location Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) PIN ASSIGNMENT SCLK VDD 1 8 D+ 2 7 SDATA D– 3 6 ALERT THERM 4 5 GND (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 16 of this data sheet. Desktop and Notebook Computers Smart Batteries Industrial Controllers Telecommunications Equipment Instrumentation Embedded Systems © Semiconductor Components Industries, LLC, 2009 1 1 1 Applications • • • • • • 1032AR 01 #YWW 1032AR #YWW XXXX Features • • • • • • • • • • • • • • • • • 8 8 1 Publication Order Number: ADM1032/D ADM1032 ADDRESS POINTER REGISTER CONVERSION RATE REGISTER D– ANALOG MUX A/D CONVERTER BUSY LOCAL TEMPERATURE LOW LIMIT REGISTER DIGITAL MUX D+ LOCAL TEMPERATURE VALUE REGISTER RUN/STANDBY DIGITAL MUX ON−CHIP TEMPERATURE SENSOR LIMIT COMPARATOR REMOTE TEMPERATURE VALUE REGISTER LOCAL TEMPERATURE HIGH LIMIT REGISTER REMOTE TEMPERATURE LOW LIMIT REGISTER REMOTE TEMPERATURE HIGH LIMIT REGISTER LOCAL THERM LIMIT REGISTER REMOTE OFFSET REGISTER EXTERNAL THERM LIMIT REGISTER CONFIGURATION REGISTER EXTERNAL DIODE OPEN−CIRCUIT ALERT THERM ADM1032 VDD INTERRUPT MASKING STATUS REGISTER SMBUS INTERFACE GND SDATA SCLK Figure 1. Functional Block Diagram ABSOLUTE MAXIMUM RATINGS Parameter Positive Supply Voltage (VDD) to GND Rating Unit −0.3, +5.5 V −0.3 to VDD + 0.3 V D− to GND −0.3 to +0.6 V SCLK, SDATA, ALERT −0.3 to +5.5 V D+ THERM Input Current, SDATA, THERM Input Current, D− ESD Rating, All Pins (Human Body Model) Maximum Junction Temperature (TJ Max) −0.3 to VDD + 0.3 V −1, +50 mA ±1 mA >1000 V 150 °C Storage Temperature Range −65 to +150 °C IR Reflow Peak Temperature 220 °C IR Reflow Peak Temperature for Pb−Free 260 °C Lead Temperature (Soldering 10 sec) 300 °C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. NOTE: This device is ESD sensitive. Use standard ESD precautions when handling. THERMAL CHARACTERISTICS Package Type qJA Unit 8−Lead SOIC−N Package 121 °C 8−Lead MSOP Package 142 °C http://onsemi.com 2 ADM1032 PIN ASSIGNMENT Pin No. Mnemonic Description 1 VDD Positive Supply, 3.0 V to 5.5 V. 2 D+ Positive Connection to Remote Temperature Sensor. 3 D− Negative Connection to Remote Temperature Sensor. 4 THERM THERM is an open−drain output that can be used to turn a fan on/off or throttle a CPU clock in the event of an overtemperature condition. Requires pullup to VDD, the same supply as the ADM1032. Note: Please refer to Power Sequencing Considerations; THERM Pin Pullup on page 15 for more information. 5 GND 6 ALERT Supply Ground Connection. Open−Drain Logic Output Used as Interrupt or SMBus Alert. 7 SDATA Logic Input/Output, SMBus Serial Data. Open−drain output. Requires pullup resistor. 8 SCLK Logic Input, SMBus Serial Clock. Requires pullup resistor. ELECTRICAL CHARACTERISTICS Parameter Conditions Min Typ Max Unit 3.0 3.30 5.5 V 0.0625 conversions/sec rate (Note 1) 170 215 mA Standby mode 5.5 10 mA 2.55 2.8 V 2.4 V ±3 °C Power Supply Supply Voltage, VDD Average Operating Supply Current, ICC Undervoltage Lockout Threshold VDD input, disables ADC, rising edge Power−On Reset Threshold 2.35 1.0 Temperature−To−Digital Converter Local Sensor Accuracy 0 ≤ TA ≤ 100°C, VCC = 3 V to 3.6 V ±1 Resolution Remote Diode Sensor Accuracy 1.0 60°C ≤ TD ≤ 100°C, VCC = 3 V to 3.6 V ±1 °C 0°C ≤ TD ≤ 120°C ±3 °C Resolution Remote Sensor Source Current Conversion Time °C 0.125 °C High level (Note 2) 230 mA Low level (Note 2) 13 mA From stop bit to conversion complete Both channels: one−shot mode with averaging switched on 35.7 142.8 ms One−shot mode with averaging off (that is, conversion rate = 32 or 64 conversions per second) 5.7 22.8 ms 0.4 V 1.0 mA Open−Drain Digital Outputs (THERM, ALERT) Output Low Voltage, VOL IOUT = −6.0 mA (Note 2) High Level Output Leakage Current, IOH VOUT = VDD (Note 2) 0.1 Serial Bus Timing (Note 2) Logic Input High Voltage, VIH SCLK, SDATA VDD = 3.0 V to 5.5 V Logic Input Low Voltage, VIL VDD = 3.0 V to 5.5 V 2.1 V 0.8 Hysteresis SCLK, SDATA 500 V mV 1. See Table 6 for information on other conversion rates. 2. Guaranteed by design, not production tested. 3. The SMBus timeout is a programmable feature. By default, it is not enabled. Details on how to enable it are available in the Serial Bus Interface section. http://onsemi.com 3 ADM1032 ELECTRICAL CHARACTERISTICS Parameter Conditions Min Typ Max Unit Serial Bus Timing (Note 2) SDATA Output Low Sink Current SDATA forced to 0.6 V 6.0 mA ALERT Output Low Sink Current ALERT forced to 0.4 V 1.0 mA Logic Input Current, IIH, IIL −1.0 Input Capacitance, SCLK, SDATA +1.0 5.0 Clock Frequency SMBus Timeout (Note 3) 25 mA pF 400 kHz 64 ms SCLK Clock Low Time, tLOW tLOW between 10% points 1.3 ms SCLK Clock High Time, tHIGH tHIGH between 90% points 0.6 ms 600 ns Start Condition Setup Time, tSU:STA Start Condition Hold Time, tHD:STA Time from 10% of SDATA to 90% of SCLK 600 ns Stop Condition Setup Time, tSU:STO Time from 90% of SCLK to 10% of SDATA 600 ns Data Valid to SCLK Rising Edge Time, tSU:DAT Time for 10% or 90% of SDATA to 10% of SCLK 100 ns 300 ns 1.3 ms Data Hold Time, tHD:DAT Bus Free Time, tBUF Between start/stop condition SCLK, SDATA Rise Time, tR 300 ns SCLK, SDATA Fall Time, tF 300 ns 1. See Table 6 for information on other conversion rates. 2. Guaranteed by design, not production tested. 3. The SMBus timeout is a programmable feature. By default, it is not enabled. Details on how to enable it are available in the Serial Bus Interface section. tLOW tR tF tHD:STA SCLK tHD:STA tHD:DAT tHIGH tSU:STA tSU:DAT tSU:STO SDATA tBUF S PS Figure 2. Diagram for Serial Bus Timing http://onsemi.com 4 P ADM1032 TYPICAL CHARACTERISTICS 1.0 20 16 TEMPERATURE ERROR (5C) TEMPERATURE ERROR (5C) 12 8 4 D+ TO GND 0 −4 −8 D+ TO V DD 0.5 0 −12 –16 –0.5 0 10 LEAKAGE RESISTANCE (MW ) 0 100 40 60 80 100 120 TEMPERATURE (5C) Figure 3. Temperature Error vs. Leakage Resistance Figure 4. Temperature Error vs. Actual Temperature Using 2N3906 13 12 11 10 TEMPERATURE ERROR (5C) TEMPERATURE ERROR (5C) 20 9 7 5 VIN = 40mV p−p 3 VIN = 250mV p−p 8 6 4 VIN = 100mV p−p 2 1 VIN = 10mV p−p –1 100k 1M 10M FREQUENCY (Hz) 0 100M 10 1M FREQUENCY (Hz) Figure 5. Temperature Error vs. Differential Mode Noise Frequency Figure 6. Temperature Error vs. Power Supply Noise Frequency 2.0 18 14 SUPPLY CURRENT (mA) TEMPERATURE ERROR (5C) 16 12 10 8 6 4 1.5 1.0 VDD = 5V 0.5 2 0 VDD = 3V 1 6 11 16 21 CAPACITANCE (nF) 26 31 0 0.01 36 Figure 7. Temperature Error vs. Capacitance Between D+ and D− 0.1 1 CONVERSION RATE (Hz) 10 Figure 8. Operating Supply Current vs. Conversion Rate http://onsemi.com 5 100 ADM1032 TYPICAL CHARACTERISTICS 80 12 70 VIN = 100mV p−p SUPPLY CURRENT (mA) TEMPERATURE ERROR (5C) 10 8 6 4 VIN = 50mV p−p 2 50 VDD = 5V 40 30 20 10 VIN = 25mV p−p 0 100k 60 1M 10M FREQUENCY (Hz) 0 100M Figure 9. Temperature Error vs. Common−Mode Noise Frequency VDD = 3.3V 1 5 10 25 50 75 100 250 SCLK FREQUENCY (kHz) STANDBY SUPPLY CURRENT ( A) 35 30 25 20 15 10 5 0 0.5 1.0 750 1000 Figure 10. Standby Supply Current vs. Clock Frequency 40 0 500 1.5 2.0 2.5 3.0 3.5 SUPPLY VOLTAGE (V) 4.0 4.5 5.0 Figure 11. Standby Supply Current vs. Supply Voltage http://onsemi.com 6 ADM1032 Functional Description This is given by: The ADM1032 is a local and remote temperature sensor and overtemperature alarm. When the ADM1032 is operating normally, the on−board A/D converter operates in a free running mode. The analog input multiplexer alternately selects either the on−chip temperature sensor to measure its local temperature or the remote temperature sensor. These signals are digitized by the ADC, and the results are stored in the local and remote temperature value registers. The measurement results are compared with local and remote, high, low, and THERM temperature limits stored in nine on−chip registers. Out−of−limit comparisons generate flags that are stored in the status register, and one or more out−of−limit results cause the ALERT output to pull low. Exceeding THERM temperature limits causes the THERM output to assert low. The limit registers can be programmed, and the device controlled and configured, via the serial SMBus. The contents of any register can also be read back via the SMBus. Control and configuration functions consist of: • Switching the device between normal operation and standby mode. • Masking or enabling the ALERT output. • Selecting the conversion rate. DV BE + ǒn f Ǔ KT q In(N) where: K is Boltzmann’s constant (1.38 x 10–23). q is the charge on the electron (1.6 x 10–19 Coulombs). T is the absolute temperature in Kelvins. N is the ratio of the two currents. nf is the ideality factor of the thermal diode. The ADM1032 is trimmed for an ideality factor of 1.008. Figure 12 shows the input signal conditioning used to measure the output of an external temperature sensor. Figure 12 shows the external sensor as a substrate transistor, provided for temperature monitoring on some microprocessors, but it could equally well be a discrete transistor. If a discrete transistor is used, the collector is not grounded and should be linked to the base. To prevent ground noise interfering with the measurement, the more negative terminal of the sensor is not referenced to ground but is biased above ground by an internal diode at the D− input. If the sensor is operating in a noisy environment, C1 can optionally be added as a noise filter. Its value should be no more than 1000 pF. See the Layout Considerations section for more information on C1. To measure DVBE, the sensor is switched between the operating currents of I and N x I. The resulting waveform is passed through a 65 kHz low−pass filter to remove noise, and then to a chopper−stabilized amplifier that performs the functions of amplification and rectification of the waveform to produce a dc voltage proportional to DVBE. This voltage is measured by the ADC to give a temperature output in twos complement format. To further reduce the effects of noise, digital filtering is performed by averaging the results of 16 measurement cycles. Signal conditioning and measurement of the internal temperature sensor is performed in a similar manner. Measurement Method A simple method of measuring temperature is to exploit the negative temperature coefficient of a diode, or the base−emitter voltage of a transistor, operated at constant current. Unfortunately, this technique requires calibration to null out the effect of the absolute value of VBE, which varies from device to device. The technique used in the ADM1032 is to measure the change in VBE when the device is operated at two different currents. VDD I N I IBIAS D+ REMOTE SENSING TRANSISTOR VOUT+ TO ADC C1 D– BIAS DIODE (eq. 1) LOW−PASS FILTER fC = 65kHz VOUT– CAPACITOR C1 IS OPTIONAL AND IT SHOULD ONLY BE USED IN VERY NOISY ENVIRONMENTS. C1 = 1000pF MAX. Figure 12. Input Signal Conditioning http://onsemi.com 7 ADM1032 Temperature Data Format Value Registers One LSB of the ADC corresponds to 0.125°C, so the ADC can measure from 0°C to 127.875°C. The temperature data format is shown in Table 1 and Table 2. The results of the local and remote temperature measurements are stored in the local and remote temperature value registers and are compared with limits programmed into the local and remote high and low limit registers. The ADM1032 has three registers to store the results of local and remote temperature measurements. These registers are written to by the ADC only and can be read over the SMBus. Offset Register Series resistance on the D+ and D− lines in processor packages and clock noise can introduce offset errors into the remote temperature measurement. To achieve the specified accuracy on this channel, these offsets must be removed. The offset value is stored as an 11−bit, twos complement value in Register 11h (high byte) and Register 12h (low byte, left justified). The value of the offset is negative if the MSB of Register 11h is 1 and positive if the MSB of Register 12h is 0. The value is added to the measured value of the remote temperature. The offset register powers up with a default value of 0°C and has no effect if nothing is written to them. Table 1. Temperature Data Format (Local Temperature and Remote Temperature High Byte Temperature Digital Output 0°C 0 000 0000 1°C 0 000 0001 10°C 0 000 1010 25°C 0 001 1001 50°C 0 011 0010 75°C 0 100 1011 100°C 0 110 0100 125°C 0 111 1101 127°C 0 111 1111 Table 3. Sample Offset Register Codes Offset Value 11h 12h −4°C 1 111 1100 0 000 0000 −1°C 1 111 1111 0 000 0000 −0.125°C 1 111 1111 1 110 0000 Remote Temperature Low Byte 0°C 0 000 0000 0 000 0000 0 000 0000 +0.125°C 0 000 0000 0 010 0000 0.125°C 0 010 0000 +1°C 0 000 0001 0 000 0000 0.250°C 0 100 0000 +4°C 0 000 0100 0 000 0000 0.375°C 0 110 0000 0.500°C 1 000 0000 0.625°C 1 010 0000 0.750°C 1 100 0000 0.875°C 1 110 0000 Table 2. Extended Temperature Resolution (Remote Temperature Low Byte Extended Resolution 0.000°C Status Register Bit 7 of the status register indicates that the ADC is busy converting when it is high. Bit 6 to Bit 3, Bit 1, and Bit 0 are flags that indicate the results of the limit comparisons. Bit 2 is set when the remote sensor is open circuit. If the local and/or remote temperature measurement is above the corresponding high temperature limit, or below or equal to the corresponding low temperature limit, one or more of these flags is set. These five flags (Bit 6 to Bit 2) are NOR’ed together, so that if any of them are high, the ALERT interrupt latch is set and the ALERT output goes low. Reading the status register clears the five flag bits, provided that the error conditions that caused the flags to be set have gone away. While a limit comparator is tripped due to a value register containing an out−of−limit measurement, or the sensor is open circuit, the corresponding flag bit cannot be reset. A flag bit can only be reset if the corresponding value register contains an in−limit measurement or the sensor is good. The ALERT interrupt latch is not reset by reading the status register but is reset when the ALERT output is serviced by the master reading the device address, provided the error condition has gone away and the status register flag bits are reset. ADM1032 Registers The ADM1032 contains registers that are used to store the results of remote and local temperature measurements and high and low temperature limits and to configure and control the device. A description of these registers follows, and further details are given in Table 3 to Table 7. Address Pointer Register The address pointer register itself does not have, or require, an address because it is the register the first data byte of every write operation is written to automatically. This data byte is an address pointer that sets up one of the other registers for the second byte of the write operation or for a subsequent read operation. The power−on default value of the address pointer register is 00h. Therefore, if a read operation is performed immediately after power−on without first writing to the address pointer, the value of the local temperature is returned because its register address is 00h. http://onsemi.com 8 ADM1032 When Flag 1 and Flag 0 are set, the THERM output goes low to indicate that the temperature measurements are outside the programmed limits. THERM output does not need to be reset, unlike the ALERT output. Once the measurements are within the limits, the corresponding status register bits are reset and the THERM output goes high. Table 6. Conversion Rate Register Codes Table 4. Status Register Bit Assignments Data Conversion/Sec Average Supply Current mA Typ at VDD = 5.5 V 00h 0.0625 0.17 01h 0.125 0.20 02h 0.25 0.21 03h 0.5 0.24 Bit Name Function 04h 1 0.29 7 BUSY 1 When ADC Converting 05h 2 0.40 6 LHIGH 1 When Local High Temp Limit Tripped 06h 4 0.61 LLOW 1 When Local Low Temp Limit Tripped 07h 8 1.1 08h 16 1.9 RHIGH 1 When Remote High Temp Limit Tripped (Note 1) 5 (Note 1) 4 (Note 1) 3 (Note 1) RLOW 1 When Remote Low Temp Limit Tripped OPEN 1 When Remote Sensor Open−Circuit 1 RTHRM 1 When Remote THERM Limit Tripped 0 LTHRM1 1 When Local THERM Limit Tripped 2 (Note 1) Configuration Register Two bits of the configuration register are used. If Bit 6 is 0, which is the power−on default, the device is in operating mode with the ADC converting. If Bit 6 is set to 1, the device is in standby mode and the ADC does not convert. The SMBus does, however, remain active in standby mode so values can be read from or written to the SMBus. The ALERT and THERM O/Ps are also active in standby mode. Bit 7 of the configuration register is used to mask the alert output. If Bit 7 is 0, which is the power−on default, the output is enabled. If Bit 7 is set to 1, the output is disabled. Power−On Default 7 MASK1 0 = ALERT Enabled 1 = ALERT Masked 0 6 RUN/ STOP 0 = Run 1 = Standby 0 Reserved 0 5 to 0 1.23 0B to FFh Reserved One−Shot Register The one−shot register is used to initiate a single conversion and comparison cycle when the ADM1032 is in standby mode, after which the device returns to standby. This is not a data register as such, and it is the write operation that causes the one−shot conversion. The data written to this address is irrelevant and is not stored. The conversion time on a single shot is 96 ms when the conversion rate is 16 conversions per second or less. At 32 conversions per second, the conversion time is 15.3 ms. This is because averaging is disabled at the faster conversion rates (32 and 64 conversions per second). Table 5. Configuration Register Bit Assignments Function 0.73 64 The ADM1032 has nine limit registers to store local and remote, high, low, and THERM temperature limits. These registers can be written to and read back over the SMBus. The high limit registers perform a > comparison, while the low limit registers perform a < or = to comparison. For example, if the high limit register is programmed with 80°C, measuring 81°C results in an alarm condition. If the low limit register is programmed with 0°C, measuring 0°C or lower results in an alarm condition. Exceeding either the local or remote THERM limit asserts THERM low. A default hysteresis value of 10°C is provided, which applies to both channels. This hysteresis can be reprogrammed to any value after powerup (Reg 0x21h). by POR. Name 32 Limit Registers 1. These flags stay high until the status register is read, or they are reset Bit 09h 0Ah Consecutive ALERT Register Conversion Rate Register This value written to this register determines how many out−of limit measurements must occur before an ALERT is generated. The default value is that one out−of−limit measurement generates an ALERT. The maximum value that can be chosen is four. The purpose of this register is to allow the user to perform some filtering of the output. This is particularly useful at the faster two conversion rates where no averaging takes place. The lowest four bits of this register are used to program the conversion rate by dividing the internal oscillator clock by 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, or 1024 to give conversion times from 15.5 ms (Code 0Ah) to 16 seconds (Code 00h). This register can be written to and read back over the SMBus. The higher four bits of this register are unused and must be set to 0. Use of slower conversion times greatly reduces the device power consumption, as shown in Table 6. http://onsemi.com 9 ADM1032 Serial Bus Interface Table 7. Consecutive ALERT Register Codes Register Value Number of Out−of−Limit Measurements Required yxxx 000x 1 yxxx 001x 2 yxxx 011x 3 yxxx 111x 4 NOTE: Control of the ADM1032 is carried out via the serial bus. The ADM1032 is connected to this bus as a slave device, under the control of a master device. There is a programmable SMBus timeout. When this is enabled, the SMBus times out after typically 25 ms of no activity. However, this feature is not enabled by default. To enable it, set Bit 7 of the consecutive alert register (Address = 22h). x = don’t care bits, and y = SMBus timeout bit. Default = 0. See SMBus section for more information. Table 8. List of ADM1032 Registers Read Address (Hex) Write Address (Hex) Not Applicable Not Applicable Address Pointer Undefined 00 Not Applicable Local Temperature Value 0000 0000 (00h) 01 Not Applicable External Temperature Value High Byte 0000 0000 (00h) 02 Not Applicable Status Undefined 03 09 Configuration 0000 0000 (00h) 04 0A Conversion Rate 0000 1000 (08h) 05 0B Local Temperature High Limit 0101 0101 (55h) (85°C) 06 0C Local Temperature Low Limit 0000 0000 (00h) (0°C) 07 0D External Temperature High Limit High Byte 0101 0101 (55h) (85°C) 08 0E External Temperature Low Limit High Byte 0000 0000 (00h) (0°C) Not Applicable 0F One−Shot 10 Not Applicable External Temperature Value Low Byte 0000 0000 11 11 External Temperature Offset High Byte 0000 0000 12 12 External Temperature Offset Low Byte 0000 0000 13 13 External Temperature High Limit Low Byte 0000 0000 14 14 External Temperature Low Limit Low Byte 0000 0000 19 19 External THERM Limit 0101 0101 (55h) (85°C) (ADM1032) 0110 1100 (6Ch) (108°C) (ADM1032−1) 20 20 Local THERM Limit 0101 0101 (55h) (85°C) 21 21 THERM Hysteresis 0000 1010 (0Ah) (10°C) 22 22 Consecutive ALERT 0000 0001 (01h) FE Not Applicable Manufacturer ID 0100 0001 (41h) FF Not Applicable Die Revision Code Undefined NOTE: Name Power−On Default Writing to Address 0F causes the ADM1032 to perform a single measurement. It is not a data register as such and it does not matter what data is written to it. Addressing the Device The serial bus protocol operates as follows: 1. The master initiates data transfer by establishing a START condition, defined as a high−to−low transition on the serial data line SDATA, while the serial clock line SCLK remains high. This indicates that an address/data stream follows. All slave peripherals connected to the serial bus respond to the START condition and shift in the next eight bits, consisting of a 7−bit address (MSB first) plus an R/W bit, which determines the In general, every SMBus device has a 7−bit device address (except for some devices that have extended, 10−bit addresses). When the master device sends a device address over the bus, the slave device with that address responds. The ADM1032 and the ADM1032−1 are available with one SMBus address, which is Hex 4C (1001 100). The ADM1032−2 is also available with one SMBus address; however, that address is Hex 4D (1001 101). http://onsemi.com 10 ADM1032 a write operation always contains a valid address that is stored in the address pointer register. If data is written to the device, the write operation contains a second data byte that is written to the register selected by the address pointer register. This is illustrated in Figure 13. The device address is sent over the bus followed by R/W set to 0. This is followed by two data bytes. The first data byte is the address of the internal data register to be written to, which is stored in the address pointer register. The second data byte is the data to be written to the internal data register. When reading data from a register, there are two possibilities: • If the address pointer register value is unknown or not the desired value, it is first necessary to set it to the correct value before data can be read from the desired data register. This is done by performing a write to the ADM1032 as before, but only the data byte containing the register read address is sent because data is not to be written to the register. This is shown in Figure 14. A read operation is then performed consisting of the serial bus address, R/W bit set to 1, followed by the data byte read from the data register. This is shown in Figure 15. • If the address pointer register is known to be at the desired address already, data can be read from the corresponding data register without first writing to the address pointer register and Figure 14 can be omitted. direction of the data transfer, that is, whether data is written to or read from the slave device. The peripheral whose address corresponds to the transmitted address responds by pulling the data line low during the low period before the ninth clock pulse, known as the acknowledge bit. All other devices on the bus now remain idle while the selected device waits for data to be read from or written to it. If the R/W bit is a 0, the master writes to the slave device. If the R/W bit is a 1, the master reads from the slave device. 2. Data is sent over the serial bus in sequences of nine clock pulses, eight bits of data followed by an acknowledge bit from the slave device. Transitions on the data line must occur during the low period of the clock signal and remain stable during the high period, since a low−to−high transition when the clock is high can be interpreted as a STOP signal. The number of data bytes that can be transmitted over the serial bus in a single read or write operation is limited only by what the master and slave devices can handle. 3. When all data bytes are read or written, stop conditions are established. In write mode, the master pulls the data line high during the 10th clock pulse to assert a STOP condition. In read mode, the master device overrides the acknowledge bit by pulling the data line high during the low period before the ninth clock pulse. This is known as no acknowledge. The master then takes the data line low during the low period before the 10th clock pulse, and high during the 10th clock pulse to assert a STOP condition. Any number of bytes of data can be transferred over the serial bus in one operation, but it is not possible to mix read and write in one operation because the type of operation is determined at the beginning and cannot subsequently be changed without starting a new operation. In the case of the ADM1032, write operations contain either one or two bytes, while read operations contain one byte and perform the following functions. To write data to one of the device data registers or read data from it, the address pointer register must first be set so that the correct data register is addressed. The first byte of Notes Although it is possible to read a data byte from a data register without first writing to the address pointer register, if the address pointer register is already at the correct value, it is not possible to write data to a register without writing to the address pointer register. The first data byte of a write is always written to the address pointer register. Don’t forget that some of the ADM1032 registers have different addresses for read and write operations. The write address of a register must be written to the address pointer if data is to be written to that register, but it is not possible to read data from that address. The read address of a register must be written to the address pointer before data can be read from that register. http://onsemi.com 11 ADM1032 9 1 1 9 SCLK A6 SDATA A5 A4 A3 A2 A1 A0 R/W D6 D7 D5 D4 D3 D2 D1 D0 ACK. BY ADM1032 START BY MASTER ACK. BY ADM1032 FRAME 2 ADDRESS POINTER REGISTER BYTE FRAME 1 SERIAL BUS ADDRESS BYTE 1 9 SCLK (CONTINUED) D7 SDATA (CONTINUED) D6 D5 D4 D2 D3 D1 D0 ACK. BY ADM1032 STOP BY MASTER FRAME 3 DATA BYTE Figure 13. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register 9 1 1 9 SCLK SDATA START BY MASTER A6 A5 A4 A3 A2 A1 A0 R/W D7 D6 D5 D4 D3 D2 D1 D0 ACK. BY ADM1032 ACK. BY ADM1032 FRAME 1 SERIAL BUS ADDRESS BYTE STOP BY MASTER FRAME 2 ADDRESS POINTER REGISTER BYTE Figure 14. Writing to the Address Pointer Register Only 19 1 9 SCLK SDATA A6 A5 A4 A3 A2 A1 A0 R/W D7 D6 D5 D4 D3 D2 D1 ACK. BY ADM1032 START BY MASTER D0 ACK. BY ADM1032 FRAME 1 SERIAL BUS ADDRESS BYTE STOP BY MASTER FRAME 2 DATA BYTE FROM ADM1032 Figure 15. Reading Data from a Previously Selected Register ALERT Output MASTER RECEIVES SMBALERT The ALERT output goes low whenever an out−of−limit measurement is detected, or if the remote temperature sensor is open−circuit. It is an open drain and requires a pullup to VDD. Several ALERT outputs can be wire−OR’ed together so that the common line goes low if one or more of the ALERT outputs goes low. The ALERT output can be used as an interrupt signal to a processor, or it can be used as an SMBALERT. Slave devices on the SMBus can not normally signal to the master that they want to talk, but the SMBALERT function allows them to do so. One or more ALERT outputs can be connected to a common SMBALERT line connected to the master. When the SMBALERT line is pulled low by one of the devices, the following procedure occurs (see Figure 16). START ALERT RESPONSE ADDRESS MASTER SENDS ARA AND READ COMMAND RD ACK DEVICE ADDRESS NO STOP ACK DEVICE SENDS ITS ADDRESS Figure 16. Use of SMBALERT 1. SMBALERT is pulled low. 2. Master initiates a read operation and sends the alert response address (ARA = 0001 100). This is a general call address that must not be used as a specific device address. 3. The device whose ALERT output is low responds to the alert response address and the master reads its device address. Since the device address is http://onsemi.com 12 ADM1032 seven bits, an LSB of 1 is added. The address of the device is now known, and it can be interrogated in the usual way. 4. If more than one device’s ALERT output is low, the one with the lowest device address has priority in accordance with normal SMBus arbitration. 5. Once the ADM1032 has responded to the alert response address, it resets its ALERT output, provided that the error condition that caused the ALERT no longer exists. If the SMBALERT line remains low, the master sends ARA again, and so on until all devices whose ALERT outputs were low have responded. 2. If the local or remote temperature continues to increase and either one exceeds the THERM limit, the THERM output asserts low. This can be used to throttle the CPU clock or switch on a fan. A THERM hysteresis value is provided to prevent a cooling fan cycling on and off. The power−on default value is 10°C, but this can be reprogrammed to any value after powerup. This hysteresis value applies to both the local and remote channels. Using these two limits in this way, allows the user to gain maximum performance from the system by only slowing it down should it be at a critical temperature. The THERM signal is open drain and requires a pullup to VDD. The THERM signal must always be pulled up to the same power supply as the ADM1032, unlike the SMBus signals (SDATA, SCLK, and ALERT) that can be pulled to a different power rail, usually that of the SMBus controller. Low Power Standby Mode The ADM1032 can be put into a low power standby mode by setting Bit 6 of the configuration register. When Bit 6 is low, the ADM1032 operates normally. When Bit 6 is high, the ADC is inhibited and any conversion in progress is terminated without writing the result to the corresponding value register. The SMBus is still enabled. Power consumption in the standby mode is reduced to less than 10 mA if there is no SMBus activity, or 100 mA if there are clock and data signals on the bus. When the device is in standby mode, it is still possible to initiate a one−shot conversion of both channels by writing XXh to the one−shot register (Address 0Fh), after which the device returns to standby. It is also possible to write new values to the limit register while it is in standby. If the values stored in the temperature value registers are now outside the new limits, an ALERT is generated even though the ADM1032 is still in standby. 1005C 905C 805C LOCAL THERM LIMIT 705C TEMPERATURE 605C LOCAL THERM LIMIT –HYSTERESIS 505C 405C THERM Figure 17. Operation of the THERM Output Table 9. THERM Hysteresis Sample Values THERM Hysteresis Binary Representation 0°C 0 000 0000 1°C 0 000 0001 10°C 0 000 1010 The ADM1032 Interrupt System The ADM1032 has two interrupt outputs, ALERT and THERM. These have different functions. ALERT responds to violations of software−programmed temperature limits and is maskable. THERM is intended as a fail−safe interrupt output that cannot be masked. If the temperature goes equal to or below the lower temperature limit, the ALERT pin is asserted low to indicate an out−of−limit condition. If the temperature is within the programmed low and high temperature limits, no interrupt is generated. If the temperature exceeds the high temperature limit, the ALERT pin is asserted low to indicate an overtemperature condition. A local and remote THERM limit can be programmed into the device to set the temperature limit above which the overtemperature THERM pin is asserted low. This temperature limit should be equal to or greater than the high temperature limit programmed. The behavior of the high limit and THERM limit is as follows: 1. If either temperature measured exceeds the high temperature limit, the ALERT output is asserted low. Sensor Fault Detection At the D+ input, the ADM1032 has a fault detector that detects if the external sensor diode is open circuit. This is a simple voltage comparator that trips if the voltage at D+ exceeds VDD − 1.0 V (typical). The output of this comparator is checked when a conversion is initiated and sets Bit 2 of the status register if a fault is detected. If the remote sensor voltage falls below the normal measuring range, for example, due to the diode being short−circuited, the ADC outputs −128 (1000 0000). Since the normal operating temperature range of the device only extends down to 0°C, this output code should never be seen in normal operation, so it can be interpreted as a fault condition. Since it is outside the power−on default low temperature limit (0°C) and any low limit that would normally be programmed, a short−circuit sensor causes an SMBus alert. http://onsemi.com 13 ADM1032 Applications Information — Factors Affecting Accuracy If a discrete transistor is being used with the ADM1032, the best accuracy is obtained by choosing devices according to the following criteria: • Base−emitter voltage greater than 0.25 V at 6 mA, at the highest operating temperature. • Base−emitter voltage less than 0.95 V at 100 mA, at the lowest operating temperature. • Base resistance less than 100 W. • Small variation in hFE (say 50 to 150) that indicates tight control of VBE characteristics. Transistors such as 2N3904, 2N3906, or equivalents in SOT−23 packages are suitable devices to use. Remote Sensing Diode Thermal Inertia and Self−Heating The ADM1032 is designed to work with substrate transistors built into processors’ CPUs or with discrete transistors. Substrate transistors are generally PNP types with the collector connected to the substrate. Discrete types can be either a PNP or an NPN transistor connected as a diode (base shorted to collector). If an NPN transistor is used, the collector and base are connected to D+ and the emitter to D−. If a PNP transistor is used, the collector and base are connected to D− and the emitter to D+. Substrate transistors are found in a number of CPUs. To reduce the error due to variations in these substrate and discrete transistors, a number of factors should be taken into consideration: 1. The ideality factor, nf, of the transistor. The ideality factor is a measure of the deviation of the thermal diode from the ideal behavior. The ADM1032 is trimmed for an nf value of 1.008. The following equation can be used to calculate the error introduced at a temperature T°C when using a transistor whose nf does not equal 1.008. Consult the processor data sheet for nf values. Accuracy depends on the temperature of the remote−sensing diode and/or the internal temperature sensor being at the same temperature as that being measured, and a number of factors can affect this. Ideally, the sensor should be in good thermal contact with the part of the system being measured, for example, the processor. If it is not, the thermal inertia caused by the mass of the sensor causes a lag in the response of the sensor to a temperature change. In the case of the remote sensor, this should not be a problem, since it is either a substrate transistor in the processor or a small package device, such as the SOT−23, placed in close proximity to it. The on−chip sensor, however, is often remote from the processor and is only monitoring the general ambient temperature around the package. The thermal time constant of the SOIC−8 package in still air is about 140 seconds, and if the ambient air temperature quickly changed by 100°, it would take about 12 minutes (five time constants) for the junction temperature of the ADM1032 to settle within 1° of this. In practice, the ADM1032 package is in electrical and therefore thermal contact with a printed circuit board and can also be in a forced airflow. How accurately the temperature of the board and/or the forced airflow reflect the temperature to be measured also affects the accuracy. Self−heating due to the power dissipated in the ADM1032 or the remote sensor causes the chip temperature of the device or remote sensor to rise above ambient. However, the current forced through the remote sensor is so small that self−heating is negligible. In the case of the ADM1032, the worst−case condition occurs when the device is converting at 16 conversions per second while sinking the maximum current of 1 mA at the ALERT and THERM output. In this case, the total power dissipation in the device is about 11 mW. The thermal resistance, qJA, of the SOIC−8 package is about 121°C/W. In practice, the package has electrical and therefore thermal connection to the printed circuit board, so the temperature rise due to self−heating is negligible. In this respect, the ADM1032 differs from and improves upon competitive devices that output zero if the external sensor goes short−circuit. These devices can misinterpret a genuine 0°C measurement as a fault condition. When the D+ and D− lines are shorted together, an ALERT is always generated. This is because the remote value register reports a temperature value of −128°C. Since the ADM1032 performs a less−than or equal−to comparison with the low limit, an ALERT is generated even when the low limit is set to its minimum of −128°C. DT + ǒnnatural * 1.008Ǔ 1.008 ǒ273.15 Kelvin ) TǓ (eq. 2) This value can be written to the offset register and is automatically added to or subtracted from the temperature measurement. 2. Some CPU manufacturers specify the high and low current levels of the substrate transistors. The high current level of the ADM1032, IHIGH, is 230 mA and the low level current, ILOW, is 13 mA. If the ADM1032 current levels do not match the levels of the CPU manufacturers, then it can become necessary to remove an offset. The CPU’s data sheet advises whether this offset needs to be removed and how to calculate it. This offset can be programmed to the offset register. It is important to note that if accounting for two or more offsets is needed, then the algebraic sum of these offsets must be programmed to the offset register. http://onsemi.com 14 ADM1032 Layout Considerations microphone cable. Connect the twisted pair to D+ and D− and the shield to GND close to the ADM1032. Leave the remote end of the shield unconnected to avoid ground loops. Because the measurement technique uses switched current sources, excessive cable and/or filter capacitance can affect the measurement. When using long cables, the filter capacitor can be reduced or removed. Cable resistance can also introduce errors. 1 W series resistance introduces about 1°C error. Digital boards can be electrically noisy environments, and the ADM1032 is measuring very small voltages from the remote sensor, so care must be taken to minimize noise induced at the sensor inputs. The following precautions should be taken. 1. Place the ADM1032 as close as possible to the remote sensing diode. Provided that the worst noise sources, that is, clock generators, data/address buses, and CRTs, are avoided, this distance can be four to eight inches. 2. Route the D+ and D− tracks close together, in parallel, with grounded guard tracks on each side. Provide a ground plane under the tracks if possible. 3. Use wide tracks to minimize inductance and reduce noise pickup. 10 mil track minimum width and spacing is recommended. GND Power Sequencing Considerations Power Supply Slew Rate When powering up the ADM1032 you must ensure that the slew rate of VDD is less than 18 mV/ms. A slew rate larger than this may cause power−on−reset issues and yield unpredictable results. THERM Pin Pullup As mentioned above, the THERM signal is open drain and requires a pullup to VDD. The THERM signal must always be pulled up to the same power supply as the ADM1032, unlike the SMBus signals (SDA, SCL and ALERT) that can be pulled to a different power rail. The only time the THERM pin can be pulled to a different supply rail (other than VDD) is if the other supply is powered up simultaneous with, or after the ADM1032 main VDD. This is to protect the internal circuitry of the ADM1032. If the THERM pullup supply rail were to rise before VDD, the POR circuitry may not operate correctly. 10MIL 10MIL D+ 10MIL 10MIL D– 10MIL 10MIL GND 10MIL Application Circuit Figure 18. Typical Arrangement of Signal Tracks Figure 20 shows a typical application circuit for the ADM1032, using a discrete sensor transistor connected via a shielded, twisted pair cable. The pullups on SCLK, SDATA, and ALERT are required only if they are not already provided elsewhere in the system. The SCLK and SDATA pins of the ADM1032 can be interfaced directly to the SMBus of an I/O controller, such as the Intel 820 chipset. 4. Try to minimize the number of copper/solder joints, which can cause thermocouple effects. Where copper/solder joints are used, make sure that they are in both the D+ and D− path and at the same temperature. Thermocouple effects should not be a major problem since 1°C corresponds to about 200 mV and thermocouple voltages are about 3 mV/°C of temperature difference. Unless there are two thermocouples with a big temperature differential between them, thermocouple voltages should be much less than 200 mV. 5. Place a 0.1 mF bypass capacitor close to the VDD pin. In very noisy environments, place a 1000 pF input filter capacitor across D+ and D− close to the ADM1032. 6. If the distance to the remote sensor is more than eight inches, the use of twisted pair cable is recommended. This works up to about six feet to 12 feet. 7. For really long distances (up to 100 feet), use shielded twisted pair, such as Belden #8451 VDD 0.1m F ADM1032 D+ D– 2N3906 SHIELD OR CPU THERMAL DIODE 3V TO 3.6V TYP 10kW SCLK SMBUS CONTROLLER SDATA ALERT VDD THERM 5V OR 12V TYP 10kW GND FAN ENABLE FAN CONTROL CIRCUIT Figure 19. Typical Application Circuit http://onsemi.com 15 ADM1032 ORDERING INFORMATION Device Order Number* Package Description ADM1032ARZ 8−Lead SOIC_N ADM1032ARZ−REEL 8−Lead SOIC_N ADM1032ARZ−REEL7 8−Lead SOIC_N ADM1032ARZ−001 8−Lead SOIC_N Package Option R−8 Part Marking #1 #2 SMBus Address Shipping† 4C 98 Tube 4C 2500 Tape & Reel 4C 1000 Tape & Reel 4C 98 Tube ADM1032ARMZ 8−Lead MSOP 4C 50 Tube ADM1032ARMZ−REEL 8−Lead MSOP 4C 3000 Tape & Reel ADM1032ARMZ−R7 8−Lead MSOP 4C 1000 Tape & Reel ADM1032ARMZ−001 8−Lead MSOP 4C 50 Tube ADM1032ARMZ−1RL 8−Lead MSOP 4C 3000 Tape & Reel ADM1032ARMZ−002 8−Lead MSOP 4D 50 Tube ADM1032ARMZ−2R 8−Lead MSOP 4D 3000 Tape & Reel ADM1032ARMZ−2RL7 8−Lead MSOP 4D 1000 Tape & Reel T1J RM−8 T13 T1C External THERM Default 85°C 108°C 85°C 108°C 85°C †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *The “Z’’ suffix indicates Pb−Free package. http://onsemi.com 16 ADM1032 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AJ −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 17 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 ADM1032 PACKAGE DIMENSIONS MSOP8 CASE 846AB−01 ISSUE O D HE PIN 1 ID NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A-01 OBSOLETE, NEW STANDARD 846A-02. E e b 8 PL 0.08 (0.003) M T B S A DIM A A1 b c D E e L HE S SEATING −T− PLANE 0.038 (0.0015) A A1 MILLIMETERS NOM MAX −− 1.10 0.08 0.15 0.33 0.40 0.18 0.23 3.00 3.10 3.00 3.10 0.65 BSC 0.40 0.55 0.70 4.75 4.90 5.05 MIN −− 0.05 0.25 0.13 2.90 2.90 INCHES NOM −− 0.003 0.013 0.007 0.118 0.118 0.026 BSC 0.021 0.016 0.187 0.193 MIN −− 0.002 0.010 0.005 0.114 0.114 MAX 0.043 0.006 0.016 0.009 0.122 0.122 0.028 0.199 L c SOLDERING FOOTPRINT* 8X 1.04 0.041 0.38 0.015 3.20 0.126 6X 8X 4.24 0.167 0.65 0.0256 5.28 0.208 SCALE 8:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Protected by US Patents 5,982,221; 6,097,239; 6,133,753; 6,169,442; 5,867,012. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 18 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative ADM1032/D