RGP02-12E // 20E HIGH VOLTAGE FAST RECOVERY RECTIFIERS PRV : 1200 - 2000 Volts Io : 0.5 Ampere DO - 41 FEATURES : * * * * * * * Glass passivated junction High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency 1.00 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) 0.205 (5.2) 0.166 (4.2) MECHANICAL DATA : 1.00 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) * Case : DO-41 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.339 gram Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL RGP RGP RGP RGP RGP UNITS 02-12E 02-14E 02-16E 02-18E 02-20E Maximum Recurrent Peak Reverse Voltage VRRM 1200 1400 1600 1800 2000 Volts Maximum RMS Voltage VRMS 840 980 1120 1260 1400 Volts Maximum DC Blocking Voltage VDC 1200 1400 1600 1800 2000 Volts Maximum Average Forward Current 0.375"(9.5mm) Lead Length Ta = 55 °C IF(AV) 0.5 Amps. Superimposed on rated load (JEDEC Method) IFSM 20 Amps. Maximum Peak Forward Voltage at 0.5 Amp. VF 2.5 Volts IR 5.0 µA IR(H) 50 µA Maximum Reverse Recovery Time ( Note 1 ) Trr 300 ns Typical Junction Capacitance ( Note 2 ) CJ 5.0 pf Junction Temperature Range TJ - 65 to + 150 °C Storage Temperature Range TSTG - 65 to + 150 °C Peak Forward Surge Current 8.3 ms. Single half sine wave Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V DC UPDATE : APRIL 23, 1998 RATING AND CHARACTERISTIC CURVES ( RGP02-12E - RGP02-20E ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 A D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 25 8.3 ms SINGLE HALF SINE WAVE PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 0.5 0.4 0.3 0.2 0.1 Ta = 50 °C 20 15 10 5 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 AMBIENT TEMPERATURE, ( °C) 2 4 6 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS Pulse Width = 300 µs 2% Duty Cycle TJ = 25 °C 0.1 0.01 0.001 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 FORWARD VOLTAGE, VOLTS 2.4 2.6 REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES 2.0 1.0 10 TJ = 100 °C 1.0 0.1 TJ = 25 °C 0.01 0 20 40 60 80 100 120 PERCENT OF RATED REVERSE VOLTAGE, (%) 140