HRS HIF3

Cover (HIF3B Series) against EMI (Electromagnetic Interference)
■Features
1. Electromagnetic Shielding Effect
This product enhances shielding effects with a metallic cover
over the ribbon cable connector (HIF3B series).
■Applications
Peripheral and termination equipment, control machines, measuring
instruments etc.
■Ordering Information
2. Screw Locking Mechanism
The locking mechanism is designed in a stubborn and
steady structure for the screw type.
3. Assembling
HIF 3 - * CVFA
The ribbon cable connector (HIF3B series) can be easily
assembled.
q
q Series Name
w
e
: HIF 3
w Number of contacts : 10, 16, 20, 26, 30, 34, 40, 50, 64
e CVFA
■I/O Cable Termination
: Cover case for EMI
■Material
Material
Finish
Zinc alloy
Nickel plated
As shown above, bend the shield knitted cord, wind
the conductive tape 1 to 2 turns, and finish cable
termination so as not to loosen the shield knitted cord.
B45
■Cover
Unit : mm
B46
Part Number
CL No.
Number of Contacts
A
B
C
D
E
HIF3-10CVFA
612-0061-4
10
8.5
8.0
31.7
38.12 17.52
HIF3-16CVFA
612-0062-7
16
7.8
7.8
34.9
41.32 25.14
HIF3-20CVFA
612-0063-0
20
9.0
8.5
39.98
46.4
HIF3-26CVFA
612-0064-2
26
10.0
9.5
47.6
54.02 37.84
HIF3-30CVFA
612-0065-5
30
9.2
9.2
52.68
59.1
HIF3-34CVFA
612-0066-8
34
11.0
10.0
57.76
64.18 48.0
HIF3-40CVFA
612-0067-0
40
13.0
10.0
65.38
71.8
55.62
HIF3-50CVFA
612-0068-3
50
14.5
10.0
78.08
84.5
68.32
HIF3-64CVFA
612-0070-5
64
15.4
10.0
95.86 102.7
30.22
42.92
86.1
■Applicable Socket Connector
Notes1 and 2: The number of polarizing guide and keys change according to products.
Unit : mm
Part Number
CL No.
Number of Contacts
A
B
C
D
Polarizing guide
HIF3BA-10D-2.54R-CL(21)
610-0190-4-21
10
17.27 10.16 11.43 12.8
HIF3BA-16D-2.54R-CL(21)
610-0192-0-21
16
24.89 17.78 19.05 20.42
HIF3BA-20D-2.54R-CL(21)
610-0193-2-21
20
29.97 22.86 24.13 25.5
HIF3BA-26D-2.54R-CL(21)
610-0194-5-21
26
37.59 30.48 31.75 33.12
HIF3BA-30D-2.54R-CL(21)
610-0195-8-21
30
42.67 35.56 36.83 38.2
HIF3BA-34D-2.54R-CL(21)
610-0196-0-21
34
47.75 40.64 41.91 43.28
HIF3BA-40D-2.54R-CL(21)
610-0197-3-21
40
55.37 48.26 49.53 50.9
HIF3BA-50D-2.54R-CL(21)
610-0198-6-21
50
68.07 60.96 62.23 63.6
One on right and left sides, resp.
HIF3BB-50D-2.54R-CL(21)
610-0201-9-21
50
68.07 60.96 62.23 63.6
One at center
HIF3BA-64D-2.54R-CL(21)
610-0200-6-21
64
85.85 78.74 80.01 81.38 One on right and left sides, resp
HIF3BB-64D-2.54R-CL(21)
610-0203-4-21
64
85.85 78.74 80.01 81.38
Polarizing keyway
One at center
One at center
One on right and left sides, resp.
One at center
■Pin Header
The pin header applicable to the socket connector HIF series can wholly use the HIF3 series. It is recommended to
use following products, considering positioning (protection of mating area) when the connector is engaged.
In addition, when the connector is installed, the locking mechanism is removed. If needed, order the product (11)
according to the specification (unlock), as shown below.
HIF3B –*PA–2.54DS,DSA(11)
Note:
HIF3BA–*PA–2.54DS,DSA(11)
HIF3B–*PA–2.54DS, DSA (11) is limited
HIF3BB–*PA–2.54DS,DSA(11)
to number of contacts as follows:
DSA-20, 30, 34, 40 contacts
DSA-26, 50 contacts
B47
■Recommended Panel catouts
A
B
C
D
10
18.52 31.7
10.16
21.8
16
26.14 34.9
17.78
29.5
20
31.22 39.98 22.86
34.5
26
38.84 47.6
30.48
42.2
30
43.92 52.68 35.56
47.2
34
49.0
57.76 40.64
52.3
40
56.62 65.38 48.26
59.9
50
69.32 78.08 60.96
72.6
64
87.1
90.4
Number of Contacts
95.86 78.74
● Right Angle Type
B48
HIF3B-*PA-DS(11)
3.45
HIF3BA
3BB-*PA-DS(11)
4.75
■Cover Assembling Procedures
4
5
2
1
6
3
1
7
8
3
BAssembling Procedures
1. Insert the connected connector (cable shield cable after termination process) 1 in the adapter metal 2, and
connect the assembly to the cover A 3.
2. Insert the cable unit 1 in the clamp slot of cover A 3, and mount the clamp metal 4. Then, tighten the unit by
screws.
3. Next, place the lock screw 5 in the right slot, and mount the cover B 7 so as not to bite the cable, and tighten the
assembly by screws. At this time, check that no clearance is found between cover A and B.
B49