NEW Modular Jack Connectors for High-Speed LAN Transmission TM21R Series Built-in Optical Indicators LED Optical indicator Optical pipe ■Features 1. Supports High-Speed LAN Transmission Meets requirements of TIA/EIA-568-B data wiring standard. Single port configuration meeting CAT5e and multiple port configuration meeting CAT5 transmission performance. As such, these products fully support Gigabit Ethernet (1000BASE-T) and Fast Ethernet (100BASE-TX) highspeed LAN transmission. Housing Optical indicator area Space saving Optical indicator 2. Built-in Optical Indicators Optical indicators are integral part of the connectors saving space on customer’s board. Compared with LED type indicators, they do not emit any electrical noise. 3. EMI protection One additional TM21 multi-port jack can be mounted in the space previously occupied by LEDs. Metal shield covers the outer surfaces of the connectors assuring complete protection against electromagnetic interference. Built-in multiple shield and ground contacts assure reliable connection with the mounting panel as well as with the mating connector. 4. FCC Standards Meets requirements of FCC Title 47, Part 68, Subpart F. ■Applications Telecom Hubs, Routers, Bridges and ATM Transmission Equipment, Ethernet Switches and Networking Equipment, Test and Measurement Equipment, Medical Diagnostic Equipment. Built-in LED type (Possibility of electromagnetic noise emission and interference.) Built-in Optical pipe type (No electromagnetic noise emission.) 2002.11 1 ■Product Specifications Current rating 1A Voltage rating 125 V AC Operating temperature range-25ç to +80ç (Note) Ratings Item Specification 01.Insulation resistance Conditions 100 V DC 100 M ohms min 02.Dielectric Withstanding Voltage No flashover or insulation breakdown (between adjacent contacts) 500 V AC / one minute 03.Withstanding voltage No flashover or insulation breakdown (between contact and shield) 1500 V AC / one minute 04.Contact resistance 230 m ohms max. 100mA DC 05.Vibration No electrical discontinuity of 5 ms or more Contact resistance: 250m ohms max. Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours / 3 axis 06.Shock No electrical discontinuity of 5ms or more Contact resistance: 250m ohms max. Acceleration of 490 m/s2, 11 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis 07.Durability (mating/unmating) Contact resistance: 250m ohms max. 200 cycles 08.Temperature cycle Contact resistance: 250 m ohms max. Insulation resistance: 100 M ohms min. (Temperature: -55ç/+5ç to +35ç/+85ç/+5ç to +35ç Duration: 30 / 5 / 30 / 5 (Minutes) 5 cycles Contact resistance: 250 m ohms max. Insulation resistance: 1 M ohms min. (High humidity) Insulation resistance: 10 M ohms min. (Dry state) 500 hours at temperature of 40ç and humidity of 90% to 95% Contact resistance: 250 m ohms max. Exposed to density 5% salt water for 48 hours 09.Humidity 10.Salt Spray Note :Includes temperature rise caused by current flow. ■Materials Material Finish Remarks Insulator Part PBT Color: Black UL94V-0 Contact Copper alloy Contact area: Gold plating Termination area: Solder plating ------- Color: Clear ------- Tin plating ------- Poly carbonate Copper alloy Optical pipe Shield ■Ordering information ●Jacks TM21 R - 5 A - 32 32 D - LP 1 2 2 3 4 5 6 7 8 q Series Name w Connector type e Jack type number r Jack performance level code TM21 R : Jack 5 : PCB Right-angle through hole type A : CAT5 (Single row, multi-port) B : CAT5 (Double row, multi port) C : Supports CAT5e (Single port) t Jack opening code 8 : 8 contacts 32 : 8 contacts /4 ports 48 : 8 contact/6 ports y Number of inserted contacts 8 : 8 contact 32 : 8 contact inserted in 4 ports=32 contacts 48 : 8 contact inserted in 6 ports=48 contacts u Number of rows Blank: Single row D: Double row i Optical pipe LP: With optical pipe inserted Blank: Without optical pipe ■Modular Jack Connectors Supporting CAT5e ●Single Port With Built-in Optical Pipe 21 16 0.8 (5.5) 1.7 13.4 0.8 3.6 0.25 0.45 13.75 Contact No.1 3 Contact No.8 (2.8) 11.43 3.05 15.75 0.8 0.35 1 6.35 2.54 13.05 10.25 0.8 (5.5) (5.5) 24 TM21R-5C 1 PC Contact No.7 Contact No.8 11.9 Part Number CL No. TM21R-5C-88-LP 222-2892-0 Contact No.1 Contact No.2 ●Single Port Without Optical Pipe 21 16 0.8 11.43 1.7 (2.8) 0.35 1 3.05 15.75 0.8 (5.5) 13.4 0.8 3.6 0.25 0.45 13.75 Contact No.1 3 Contact No.8 6.35 2.54 13.05 10.25 0.8 (5.5) (5.5) 24 TM21R-5C 1 PC Contact No.7 Contact No.8 11.9 Part Number CL No. TM21R-5C-88 222-2893-2 Contact No.1 Contact No.2 3 BRecommended PCB mounting patterns ●With Built-in Optical Pipe ●Without Optical Pipe 11.9 8.89 No ground traces 2 11.43 Printed board edge Connector front edge 11.43MIN 15.75 No conductive traces *Recommendations for PCB Design 1 1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Area indicated should be free of ground traces. 4 Recommended board thickness: 1.6mm. 5 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. Other Series TM21R Series 7 5 3 1 8 5 3 2 8 6 4 2 5 7 6 4 1 Suggested LEDs LED light emitting center BPanel Cutout ●For Both Types, With and Without Built-in Optical Pipe 4.5 0.6MIN (33) 0.15 TM21R--5C--88--LP 14.1 PCB mounting surface Panel side 1 Connector front surface 16.4 1 0 2.8 -0.8 6.75 10.25 *Recommendations for Panel Design 1 The shield contacts should connect with the panel cut-out on all sides. 4 +1 -2 1 Lock lever TM21P--88P 2 PCB mounting pattern 2.7MAX 4.5MIN 3 .6 3MIN 2 1 6.75 3 4 3MIN 5 6 6.75 2.54 6.35 3MIN Printed board edge Connector front edge 11.43MIN No conductive traces 7 1 3.2MAX 15.75 8 3.05 2Ø1 .6 11.43 6.75 Ø3 2- 3MIN .2 2 1 6.75 3 4 Contact No. 2Ø1 2.54 5 6 6.35 13.05 8 3 1 Ø1 .2 Ø3 2- No ground traces Contact No. 7 6.35 3.81 1.27 LED light emission area 8- 3.05 8.89 LED location area 1 8-Ø 6.35 3.81 1.27 1.5MAX ■Modular Receptacles Supporting CAT5 ●Single row/ multiple ports, with Built-in Optical Pipe 59.18 25.9 41.91 CL No. TM21R-5A-3232-LP 222-2873-5 1.7 (3.5) 0.35 Contact No.7 53.81 1.4 2.5 Contact No.8 58.93 8.34 10.25 1 15.525 5.8 8.34 1 12.7 1 (6) 15.4 15.3 0.75 1 15.4 3.6 0.45 Contact No.2 0.25 Contact No.1 (6) Part Number (6) Contact No.8 Contact No.1 3 13.97 11.9 BRecommended PCB mounting patterns LED Mount Area Dimensions 58.93 41.91 CL-220 Series 13.97 12.7 8.34 1.45 1.5 1.6 12.7 1.4 32-Ø1 8.34 1 4 6 7 2 3 5 8 10.9 1.3 4 11.9 1.2 5.8 LED light emission area 8.89 6.35 3.81 1.27 4 12.7 LED location area 15.525 4-Ø2 SML-010 Series SML-020 Series 1 No conductive traces 2 0.6 Printed board edge Connector front edge 53.81 4.4 12.7 2-Ø3.2 Contact No. 2.7 1 4-Ø2 2.5 3MIN 6MAX 10.4 *Recommendations for PCB Design 1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Recommended board thickness: 1.6mm. 4 To assure that the indicator light pipes operates correctly the LED’s must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 4 Suggested LEDs Series Name CL-220 Manufacturer Citizen Electronics Co., Ltd. SML-010 Rohm Co., LTD SML-020 Rohm Co., LTD 1 PCB mounting pattern 2 1 4 3 6 5 8 7 1 2 4 3 6 5 7 8 5 BRecommended Panel Cutout 0.4MIN 0.15 15.8 PCB mounting surface 4.5MIN 13.97 1 41.91 Panels Side 59.6 +1 (34) TM21P-- 88P 5 - 2.5 Connector front surface Lock lever 3.5 6 MAX 0 -1 10.25 *Recommendations for Panel Design 1 The shield contacts should connect with the panel cut-out on all sides. 6 1 Shield spring contact ●Double row / multiple port, with Built-in Optical Pipe A B 32.5 (6) 27.9 0.75 1.7 28 3.6 Contact No.1 0.45 Contact No.1 0.25 C D 2 3 5 8 1 4 6 7 7 6 4 1 8 5 3 2 14.94 12.4 1 PBT 14.94 10.25 5.8 1 1.4 2.5 22.125 8.34 Lower row connectors contacts (6) (6) 1 Contact No.8 Lower row 0.35 (3.5) 19.3 3 TM21R-5B-3232D-LP 28 13.97 Contact No.8 1 Upper row Upper row connectors contacts 7.7 TM21R-5B-4848D-LP 11.9 Part Number CL No. A B C D TM21R-5B-3232D-LP 222-2879-1 59.18 41.91 53.81 58.93 TM21R-5B-4848D-LP 222-2885-4 87.12 69.85 81.75 86.87 BRecommended PCB mounting pattern A B 4 4 Upper row LED mount position 11.9 Lower row LED mount position 8.89 6.35 LED light emission area E- Ø2 1.2 3.81 1.27 Upper row contact hole 1.3 1.4 13.97 7.7 2.5 4- Ø2 1 Contact No. No conductive traces 22.125 14.94 Printed board edge 2 Connector front edge C 2- Ø3.2 12.4 8.34 1 4 6 7 2 3 5 8 5.8 14.94 D- Ø1 3 MIN 6 MAX 19.3 Lower row contact hole 8 5 3 2 7 6 4 1 Part Number CL No. A B C D E TM21R-5B-3232D-LP 222-2879-1 58.93 41.91 53.81 64 4 TM21R-5B-4848D-LP 222-2885-4 86.87 69.85 81.75 96 6 *Recommendations for PCB Design 1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Recommended board thickness: 1.6mm. 4 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 1 PCB mounting pattern Other Series 7 8 5 6 2 1 3 4 4 3 1 2 6 5 TM21R Series 8 7 8 7 5 6 1 2 3 4 4 3 2 1 6 5 7 8 4 Suggested LEDs Series Name Manufacturer CL-220 Citizen Electronics Co., Ltd. 7 BPanes Cutout Shield spring contact spring 28.4 1 0.4 MIN 0.15 PCB mounting surface 4.5MIN 13.97 A Panel Side B Part Number CL No. A B TM21R-5B-3232D-LP 222-2879-1 41.91 59.60 TM21R-5B-4848D-LP 222-2885-4 69.85 87.54 (34) 5 Lock lever TM21P -- 88P 1 6 MAX 3.5 -10 10.25 *Recommendations for Panel Design 1 The shield contacts should connect with the panel cut-out on all sides. 8 1 TM21R -- 5B -- * * * * D -- LP Connector front surface 1 +1 -2.5 BTechnical Documentation CAT5e Transmission Characteristics Data Representative values of the various transmission characteristics data for fully mated receptacle (TM21R-5C-88-LP) and plug (TM21P-88P). All plugs in the TM21R-5C Series that were manufactured based on the De-embedded method of the TIA/EIA-568-B.2 standard and meet performance requirements of CAT5e single transmission. Note:These data are for the listed connector combination. Inquire with your Hirose Electric account representative about other combinations. ●Signal Attenuation Attenuation(dB) 0.5 0.4 0.3 0.2 0.1 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec ●Near-End Crosstalk (NEXT) Data 120 NEXT(dB) 100 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2-3,6 1,2-4,5 1,2-7,8 3,6-4,5 3,6-7,8 4,5-7,8 CAT5e Spec ●Return Loss Return Loss(dB) 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec 9 ●Far-End Crosstalk (FEXT) 120 FEXT(dB) 100 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 90 100 90 100 Frequency(MHz) 1,2-3,6 3,6-1,2 4,5-1,2 7,8-1,2 CAT5e Spec 1,2-4,5 3,6-4,5 4,5-3,6 7,8-3,6 1,2-7,8 3,6-7,8 4,5-7,8 7,8-4,5 ●Propagation Delay 3 Delay(ns) 2.5 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec ●Propagation Delay (Delay Skew) 1.4 Delay Skew(ns) 1.2 1 0.8 0.6 0.4 0.2 0 0 10 20 30 40 50 60 70 Frequency(MHz) Measurement Value 10 CAT5e Spec 80 BReference Documentation ●CAT6 Certification Received Only the high quality plugs in the TM21R-5C Series (based on the De-embedded method of the TIA/EIA-568-B.2 standard) clear CAT6 single transmission performance. A certificate was issued by the GHMT, independent European testing company. Certificate of Acceptance Return Loss NEXT 11 USA: HIROSE ELECTRIC U.S.A., INC. 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : 1 805 522 7958 Fax : 1 805 522 3217 http://www.hirose.com GERMANY: EUROPE BRANCH: HIROSE ELECTRIC GmbH HIROSE ELECTRIC CO., LTD. First Class Building 4F, Beechavenue 46.1119PV Zeppelinstrasse 42 D-73760 Ostfildern Kemnat Phone : 49 711 4560021 Schiphol-Rijk, The Netherlands Fax : 49 711 4560729 Phone : 31 20 6557 460 http://www.hirose.de Fax : 31 20 6557 469 http://hiroseeurope.com CHINA: HIROSE ELECTRIC CO., LTD. 10F,No.06, Shanghai Times Square office Tower, 93. Huai Hai Zhong Road, Luwan Shanghai Phone : 86 21 6391 0011 Fax : 86 21 6391 0101 HONG KONG: HIROSE ELECTRIC CO., LTD. Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha Tsui East, Kowloon Phone : 852 2803 5338 Fax : 852 2591 6560 SINGAPORE: HIROSE ELECTRIC CO., LTD. 10 Anson Road #34-13 International Plaza 079903 Phone : 65 6324 6113 Fax : 65 6324 6123 TAIWAN: HIROSE ELECTRIC CO., LTD. No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei Phone : 886 2 2557 7351,7352 Fax : 886 2 2552 9851 to World E inks le eL s onic ctr Crea tiv UNITED KINGDOM: KOREA: HIROSE ELECTRIC UK LTD. HIROSE KOREA CO., LTD. Crownhill Business Centre 22 Vincent Avenue (#2NA311,Shihwa Industrial Complex), Crownhill, Milton Keynes MK8 OAB 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do Phone : 44 1908 305400 Phone : 82 31 496 7000,7124 Fax : 44 1908 305401 Fax : 82 31 496 7101 http://www.hirose.co.uk http://www.hirose.co.kr ® HIROSE ELECTRIC CO., LTD. 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933 12 The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of product improvements.