MCC SL03 THRU SL24 omponents 21201 Itasca Street Chatsworth !"# $ % !"# Features l l l l l Transient SOT-23 Package For surface mount application Protects 3.0/3.3 up through 24V Components Protects 1 Unidirectional line Provides electrically isolated protection Tape & Reel EIA Standard 481. Voltage Suppressor 300 Watt Mechanical Data l l l l SOT-23 Molded: SOT-23 Surface Mount Body marked with device number. Mounting Position: Any Weight: 0.14 grams (approx.) A D C MAXIMUM RATINGS § § § § F o B E o Operating Temperature: -55 C to +150 C Storage Temperature: -55oC to +150oC SL03 thru SL24 have a Peak Pulse Power: 300 Watts (8/20 usec, Figure 1) Pulse Repetition Rate: <.01% Description This product provides unidirectional protection for 1 line by connecting the input/output line to pin 1, pin 2 to common or ground and pin 3 (is not connected). The SL03 thru SL24 product provides board level protection from static electricity and other induced-voltage surges that can damage sensitive circuitry. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays protect 3.0/3.3 Volt components such as DRAM's, SRAM's, COMS, HCOMS, HSIC, and low volt. interfaces up to 24 volts. Because of the physical size, weight and protection capabilities, this product is ideal for use in but not limited to miniaturized electronic equipment such as hand held instruments, computers, computer peripherals and cell phones. H G J DIMENSIONS DIM A B C D E F G H J K INCHES MIN .110 .083 .047 .035 .070 .018 .0005 .035 .003 .015 MAX .120 .098 .055 .041 .081 .024 .0039 .044 .007 .020 MM MIN 2.80 2.10 1.20 .89 1.78 .45 .013 .89 .085 .37 MAX 3.04 2.64 1.40 1.03 2.05 .60 .100 1.12 .180 .51 NOTE Suggested Solder Pad Layout .031 .800 .035 .900 .079 2.000 .037 .950 .037 .950 www.mccsemi.com inches mm MCC SL03 thru SL24 100 Ipp -- Peak Pulse Current -- % Ipp PPP - PEAK PULSE POWER WAVE FORMS 8/20 µs 300 W pulse 10 1.0 .10 100ns 1µs 10µs 100µs 1ms td – PULSE TIME - SEC 100 Peak Value -- Ipp 8 X 20 Waveform 50 Half-Value -- Ipp 2 0 0 20 10 30 t 10ms td t -- Time in microsec FIGURE 1 Peak Pulse Power Vs Pulse Time FIGURE 2 Pulse Wave Form MOUNTING PAD SOT23 CIRCUIT DIAGRAM º ELECTRICAL CHARACTERISTICS @ 25 C Unless otherwise specified PART NUMBER DEVICE MARKING C TEMPERATURE COEFFICIENT OF VBR áVBR µA pF mV/ºC MAX MAX MAX -5 CLAMPING VOLTAGE VC @ 5 Amp (FIGURE 2) VOLTS LEAKAGE CURRENT ID @ VWM VOLTS CLAMPING VOLTAGE VC @ 1 Amp (FIGURE 2) VOLTS MIN MAX MAX STAND OFF VOLTAGE VWM BREAKDOWN VOLTAGE VBR @1 mA VOLTS CAPACITANCE @0V, 1 MHz SL03 L03 3.3 4 8 11 200 3 SL05 L05 5.0 6.0 10.8 13 100 3 3 SL12 L12 12.0 13.3 19 26 1 3 10 SL15 L15 15.0 16.7 25 32 1 3 13 SL24 L24 24.0 26.7 44 57 1 3 30 NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off Voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. www.mccsemi.com