SL03-SL24 TVS Array Series DESCRIPTION (300 watt) This 3 pin ULTRA LOW CAPACITANCE TRANSIENT VOLTAGE SUPPRESSOR is designed for use in applications where protection is required at the board level from voltage transients caused by electrostatic discharge (ESD) as defined by IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4. This product provides unidirectional protection for 1 line by connecting the Input/Output line to pin 1, pin 2 to common or ground and pin 3 (is not connected). The SL03 thru SL24 product provides board level protection from static electricity and other induced-voltage surges that can damage sensitive circuitry. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays protect 3.0/3.3 Volt components such as DRAM’s, SRAM’s, CMOS, HCMOS, HSIC, and low voltage interfaces up to 24 Volts. Because of the physical size, weight and protection capabilities, this product is ideal for use in but not limited to miniaturized electronic equipment such as hand held instruments, computers, computer peripherals and cell phones. FEATURES • • • • PACKAGING • • Protects 3.0/3.3 up through 24V Components Protects 1 Unidirectional line Provides electrically isolated protection SOT-23 Packaging • MECHANICAL MAXIMUM RATINGS • • • • Tape & Reel EIA Standard 481 7 inch reel 5,000 pieces 13 inch reel 10,000 pieces • • • Operating Temperatures: -55ºC to +150ºC Storage Temperature: -55ºC to +150ºC SL03 thru SL24 have a Peak Pulse Power: 300 Watts (8/20 µsec, Figure 1) Pulse Repetition Rate: <.01% Molded SOT-23 Surface Mount Weight: .014 grams (approximate) Body Marked with device number º ELECTRICAL CHARACTERISTICS @ 25 C Unless otherwise specified PART NUMBER DEVICE MARKING CLAMPING VOLTAGE VC @ 5 Amp (FIGURE 2) VOLTS LEAKAGE CURRENT ID @ VWM CAPACITANCE @0V, 1 MHz C TEMPERATURE COEFFICIENT OF VBR áVBR VOLTS CLAMPING VOLTAGE VC @ 1 Amp (FIGURE 2) VOLTS µA pF mV/ºC STAND OFF VOLTAGE VWM BREAKDOWN VOLTAGE VBR @1 mA VOLTS MAX MIN MAX MAX MAX MAX MAX SL03 L03 3.3 4 8 11 200 5 -5 SL05 L05 5.0 6.0 9.8 11 100 5 3 SL12 L12 12.0 13.3 19 26 1 5 10 SL15 L15 15.0 16.7 25 32 1 5 13 SL24 L24 24.0 26.7 44 57 1 5 30 NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off Voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. http://www.luguang.cn mail:[email protected] SL03-SL24 TVS Array Series 100 Ipp -- Peak Pulse Current -- % Ipp PPP - PEAK PULSE POWER WAVE FORMS 8/20 µs 300 W pulse 10 1.0 .10 100ns 1µs 10µs 100µs 1ms td – PULSE TIME - SEC 10ms Peak Value -- Ipp 8 X 20 Waveform 50 Half-Value -- Ipp 2 0 0 10 20 td FIGURE 2 Pulse Wave Form CIRCUIT DIAGRAM PACKAGE OUTLINE http://www.luguang.cn 30 t t -- Time in microsec FIGURE 1 Peak Pulse Power Vs Pulse Time MOUNTING PAD SOT23 100 mail:[email protected]