® PCM56P PCM56U DESIGNED FOR AUDIO Serial Input 16-Bit Monolithic DIGITAL-TO-ANALOG CONVERTER FEATURES ● SERIAL INPUT ● –92dB MAX THD: FS Input, K Grade ● –74dB MAX THD: –20dB Input, K Grade ● ● ● ● ● ● ● ● ● ● 96dB DYNAMIC RANGE NO EXTERNAL COMPONENTS REQUIRED 16-BIT RESOLUTION 15-BIT MONOTONICITY, TYP 0.001% OF FSR TYP DIFFERENTIAL LINEARITY ERROR 1.5µs SETTLING TIME, TYP: Voltage Out ±3V OR ±1mA AUDIO OUTPUT EIAJ STC-007-COMPATIBLE OPERATES ON ±5V TO ±12V SUPPLIES PINOUT ALLOWS IOUT OPTION ● PLASTIC DIP OR SOIC PACKAGE This converter is completely self-contained with a stable, low noise, internal zener voltage reference; high speed current switches; a resistor ladder network; and a fast settling, low noise output operational amplifier all on a single monolithic chip. The converters are operated using two power supplies that can range from ±5V to ±12V. Power dissipation with ±5V supplies is typically less than 200mW. Also included is a provision for external adjustment of the MSB error (differential linearity error at bipolar zero) to further improve total harmonic distortion (THD) specifications if desired. Few external components are necessary for operation, and all critical specifications are 100% tested. This helps assure the user of high system reliability and outstanding overall system performance. The PCM56 is packaged in a high-quality 16-pin molded plastic DIP package or SOIC and has passed operating life tests under simultaneous high-pressure, high-temperature, and high-humidity conditions. DESCRIPTION RF The PCM56 is a state-of-the-art, fully monotonic, digital-to-analog converter that is designed and specified for digital audio applications. This device employs ultra-stable nichrome (NiCr) thin-film resistors to provide monotonicity, low distortion, and low differential linearity error (especially around bipolar zero) over long periods of time and over the full operating temperature. Reference 16-Bit IOUT DAC Audio Output 16-Bit Input Latch 16-Bit Serial-to-Parallel Conversion Clock LE Data International Airport Industrial Park • Mailing Address: PO Box 11400 • Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd. • Tucson, AZ 85706 Tel: (520) 746-1111 • Twx: 910-952-1111 • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 © 1987 Burr-Brown Corporation PDS-700D Printed in U.S.A. August, 1993 SPECIFICATIONS ELECTRICAL Typical at +25°C, and nominal power supply voltages ±5V, unless otherwise noted. PCM56U, PCM56P-J, -K PARAMETER MIN DIGITAL INPUT Resolution Digital Inputs(1): VIH VIL IIH, VIN = +2.7V IIL, VIN = +0.4V Input Clock Frequency TYP MAX UNITS +VL +0.8 +1.0 –50 Bits V V µA µA MHz 16 +2.4 0 10.0 TRANSFER CHARACTERISTICS ACCURACY Gain Error Bipolar Zero Error Differential Linearity Error Noise (rms, 20Hz to 20kHz) at Bipolar Zero (VOUT models) ±2.0 ±30 ±0.001 6 % mV % of FSR(2) µV TOTAL HARMONIC DISTORTION VO = ±FS at f = 991Hz: PCM56P-K PCM56P-J PCM56P, PCM56U PCM56P-L VO = –20dB at f = 991Hz: PCM56P-K PCM56P-J PCM56P, PCM56U PCM56P-L VO = –60dB at f = 991Hz: PCM56P-K PCM56P-J PCM56P, PCM56U PCM56P-L –94 –94 –94 –94 –75 –75 –75 –75 –35 –35 –35 –35 MONOTONICITY 15 Bits DRIFT (0°C to +70°C) Total Drift(3) Bipolar Zero Drift ±25 ±4 ppm of FSR/°C ppm of FSR/°C SETTLING TIME (to ±0.006% of FSR) Voltage Output: 6V Step 1LSB Slew Rate Current Output, 1mA Step: 10Ω to 100Ω Load 1kΩ Load(4) 1.5 1.0 10 350 350 µs µs V/µs ns ns WARM-UP TIME –92 –88 –82 –80 –74 –68 –68 –60 –34 –28 –28 –20 1 OUTPUT Voltage Output Configuration: Bipolar Range Output Current Output Impedance Short Circuit Duration Current Output Configuration: Bipolar Range (±30%) Output Impedance (±30%) ±2.0 POWER SUPPLY REQUIREMENTS(5) Voltage: +VS and +VL –VS and –VL Supply Drain (No Load): +V (+VS and +VL = +5V) –V (–VS and –VL = –5V) +V (+VS and +VL = +12V) –V (–VS and –VL = –12V) Power Dissipation: VS and VL = ±5V VS and VL = ±12V +4.75 –4.75 TEMPERATURE RANGE Specification Operation Storage 0 –25 –60 dB dB dB dB dB dB dB dB dB dB dB dB Min ±3.0 0.10 V mA Ω Indefinite to Common ±1.0 1.2 mA kΩ +5.00 –5.00 +10.00 –25.0 +12.0 –27.0 175 468 +13.2 –13.2 +17.0 –35.0 260 +70 +70 +100 V V mA mA mA mA mW mW °C °C °C NOTES: (1) Logic input levels are TTL/CMOS-compatible. (2) FSR means full-scale range and is equivalent to 6V (±3V) for PCM56 in the VOUT mode. (3) This is the combined drift error due to gain, offset, and linearity over temperature. (4) Measured with an active clamp to provide a low impedance for approximately 200ns. (5) All specifications assume +VS connected to +VL and –VS connected to –VL. If supplies are connected separately, –VL must not be more negative than –VS supply voltage to assure proper operation. No similar restriction applies to the value of +VL with respect to +VS. ® PCM56 2 PACKAGE INFORMATION ABSOLUTE MAXIMUM RATINGS DC Supply Voltages ...................................................................... ±16VDC Input Logic Voltage ............................................................ –1V to +VS/+VL Power Dissipation .......................................................................... 850mW Operating Temperature ..................................................... –25°C to +70°C Storage Temperature ...................................................... –60°C to +100°C Lead Temperature (soldering, 10s) ................................................ +300°C MODEL PCM56U PCM56P PCM56P-J PCM56P-K PCM56P-L PACKAGE PACKAGE DRAWING NUMBER(1) 16-Pin SOIC 16-Pin Plastic DIP 16-Pin Plastic DIP 16-Pin Plastic DIP 16-Pin Plastic DIP 211 180 180 180 180 NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix D of Burr-Brown IC Data Book. PIN ASSIGNMENTS PIN DESCRIPTION MNEMONIC P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 Analog Negative Supply Logic Common Logic Positive Supply No Connection Clock Input Latch Enable Input Serial Data Input Logic Negative Supply Voltage Output Feedback Resistor Summing Junction Analog Common Current Output MSB Adjustment Terminal MSB Trim-pot Terminal Analog Positive Supply –VS LOG COM +VL NC CLK LE DATA –VL VOUT RF SJ ANA COM IOUT MSB ADJ TRIM +VS CONNECTION DIAGRAM –5V 1µF –VS Logic Common 1 16 1µF 15 Trim(1) 2 +5V +VL 3 1µF –5V 16-Bit IOUT DAC 16-Bit Serial to Parallel Conversion 14 MSB Adjust(1) NC 4 13 CLK 5 12 LE 6 Data 7 –VL +5V –VS 16-Bit DAC Latch Control Logic and Level Shifting Circuit 11 10 IOUT Analog Common SJ RF Analog Output 9 8 VOUT (±3.0V) 1µF NOTE: (1) MSB error (Bipolar Zero differential linearity error) can be adjusted to zero using the external circuit shown in Figure 6. ® 3 PCM56 DISCUSSION OF SPECIFICATIONS All Bits On 0111...1111 Gain Drift 0111...1110 The PCM56 is specified to provide critical performance criteria for a wide variety of applications. The most critical specifications for D/A converter in audio applications are Total Harmonic Distortion, Differential Linearity Error, Bipolar Zero Error, parameter shifts with time and temperature, and settling time effects on accuracy. Digital Input 0000...0010 The PCM56 is factory-trimmed and tested for all critical key specifications. 0000...0001 0000...0000 Offset Drift 1111...1111 Bipolar Zero 1111...1110 1000...0001 The accuracy of a D/A converter is described by the transfer function shown in Figure 1. Digital input to analog output relationship is shown in Table I. The errors in the D/A converter are combinations of analog errors due to the linear circuitry, matching and tracking properties of the ladder and scaling networks, power supply rejection, and reference errors. In summary, these errors consist of initial errors including Gain, Offset, Linearity, Differential Linearity, and Power Supply Sensitivity. Gain drift over temperature rotates the line (Figure 1) about the bipolar zero point and Offset drift shifts the line left or right over the operating temperature range. Most of the Offset and Gain drift with temperature or time is due to the drift of the internal reference zener diode. The converter is designed so that these drifts are in opposite directions. This way the Bipolar Zero voltage is virtually unaffected by variations in the reference voltage. 1000...0000 Analog Output –FSR/2 (+FSR/2) –1LSB * See Table I for digital code definitions. FIGURE 1. Input vs Output for an Ideal Bipolar D/A Converter. POWER SUPPLY SENSITIVITY Changes in the DC power supplies will affect accuracy. The PCM56 power supply sensitivity is shown by Figure 2. Normally, regulated power supplies with 1% or less ripple are recommended for use with the DAC. See also Power Supply Connections paragraph in the Installation and Operating Instructions section. DIGITAL INPUT CODES SETTLING TIME Settling time is the total time (including slew time) required for the output to settle within an error band around its final value after a change in input (see Figure 3). The PCM56 accepts serial input data (MSB first) in the Binary Two’s Complement (BTC) form. Refer to Table I for input/output relationships. DIGITAL INPUT Settling times are specified to ±0.006% of FSR: one for a large output voltage change of 6V and one for a 1LSB change. The 1LSB change is measured at the major carry (0000 hex to ffff hex), the point at which the worst-case settling time occurs. ANALOG OUTPUT Binary Two’s Complement (BTC) DAC Output Voltage (V), VOUT Mode Current (mA), IOUT Mode 7FFF Hex 8000 Hex 0000 Hex FFFF Hex + Full Scale – Full Scale Bipolar Zero Zero –1LSB +2.999908 –3.000000 0.000000 –0.000092 –0.999970 +1.000000 0.000000 +0.030500µA 86 TABLE I. Digital Input to Analog Output Relationship. Power Supply Rejection (dB) BIPOLAR ZERO ERROR Initial Bipolar Zero Error (Bit 1 “on” and all other bits “off”) is the deviation from 0V out and is factory-trimmed to typically ±30mV at +25°C. DIFFERENTIAL LINEARITY ERROR Differential Linearity Error (DLE) is the deviation from an ideal 1LSB change from one adjacent output state to the next. DLE is important in audio applications because excessive DLE at Bipolar Zero (at the “major carry”) can result in audible crossover distortion for low level output signals. Initial DLE on the PCM56 is factory trimmed to typically ±0.001% of FSR. The MSB DLE is adjustable to zero using the circuit shown in Figure 6. 74 68 62 Positive Supplies 56 52 46 40 34 28 1 10 100 1k Frequency (Hz) FIGURE 2. Power Supply Sensitivity. ® PCM56 Negative Supplies 80 4 10k 100k The THD is defined as the ratio of the square root of the sum of the squares of the values of the harmonics to the value of the fundamental input frequency and is expressed in percent or dB. The rms value of the PCM56 error referred to the input can be shown to be: Accuracy Percent Full-Scale Range (%) 1.0 Voltage Output Mode 0.3 Current Output Mode 0.1 0.03 n ∈ rms = 1/n 0.01 E (i ) + E (i) L Q i =1 RL = 200Ω 0.003 0.001 0.01 ∑ 0.1 1.0 2 (1) where n is the number of samples in one cycle of any given sine wave, EL(i) is the linearity error of the PCM56 at each sampling point, and EQ(i) is the quantization error at each sampling point. The THD can then be expressed as: 10.0 Settling Time (µs) THD = ∈ rms / E rms FIGURE 3. Full Scale Range Settling Time vs Accuracy. n STABILITY WITH TIME AND TEMPERATURE 1 /n The parameters of a D/A converter designed for audio applications should be stable over a relatively wide temperature range and over long periods of time to avoid undesirable periodic readjustment. The most important parameters are Bipolar Zero Error, Differential Linearity Error, and Total Harmonic Distortion. Most of the Offset and Gain drift with temperature or time is due to the drift of the internal reference zener diode. The PCM56 is designed so that these drifts are in opposite directions so that the Bipolar Zero voltage is virtually unaffected by variations in the reference voltage. Both DLE and THD are dependent upon the matching and tracking of resistor ratios and upon VBE and hFE of the current-source transistors. The PCM56 was designed so that any absolute shift in these components has virtually no effect on DLE or THD. The resistors are made of identical links of ultra-stable nichrome thin-film. The current density in these resistors is very low to further enhance their stability. ∑ i =1 E (i ) + E (i) L Q 2 (2) = X 100% Erms where Erms is the rms signal-voltage level. This expression indicates that, in general, there is a correlation between the THD and the square root of the sum of the squares of the linearity errors at each digital word of interest. However, this expression does not mean that the worst-case linearity error of the D/A is directly correlated to the THD. For the PCM56 the test period was chosen to be 22.7µs (44.1kHz), which is compatible with the EIAJ STC-007 specification for PCM audio. The test frequency is 991Hz and the amplitude of the input signal is 0dB, –20dB, and –60dB down from full scale. Figure 4 shows the typical THD as a function of output voltage. Figure 5 shows typical THD as a function of frequency. DYNAMIC RANGE The Dynamic Range is a measure of the ratio of the smallest signals the converter can produce to the full-scale range and is usually expressed in decibels (dB). The theoretical dynamic range of a converter is approximately 6 x n, or about 96dB of a 16-bit converter. The actual, or useful, dynamic range is limited by noise and linearity errors and is therefore somewhat less than the theoretical limit. However, this does point out that a resolution of at least 16 bits is required to obtain a 90dB minimum dynamic range, regardless of the accuracy of the converter. Another specification that is useful for audio applications is Total Harmonic Distortion. Total Harmonic Distortion (%) 10.0 TOTAL HARMONIC DISTORTION THD is useful in audio applications and is a measure of the magnitude and distribution of the Linearity Error, Differential Linearity Error, and Noise, as well as Quantization Error. To be useful, THD should be specified for both high level and low level input signals. This error is unadjustable and is the most meaningful indicator of D/A converter accuracy for audio applications. 1.0 14 Bits 0.1 0.01 16 Bits 0.001 –60 –50 –40 –30 –20 –10 0 VOUT (dB) 0dB = Full Scale Range (FSR) FIGURE 4. Total Harmonic Distortion (THD) vs VOUT. ® 5 PCM56 A much simpler method is to dynamically adjust the DLE at BPZ. Again, refer to Figure 6 for circuitry and component values. Assuming the device has been installed in a digital audio application circuit, send the appropriate digital input to produce a –80dB level sinusoidal output. While measuring the THD of the audio circuit output, adjust the 100kΩ potentiometer until a minimum level of distortion is observed. Total Harmonic Distortion (%) 0.1 (–20dB) 0.01 470kΩ 100kΩ Trim 15 (Full Scale) 200kΩ 1 –VS 0.001 100 1k 10k 20k MSB Adjust 14 Frequency (Hz) FIGURE 6. MSB Adjustment Circuit. FIGURE 5. Total Harmonic Distortion (THD) vs Frequency. INPUT TIMING CONSIDERATIONS Figure 7 and 8 refer to the input timing required to interface the inputs of PCM56 to a serial input data stream. Serial data is accepted in Binary Two’s Complement (BTC) with the MSB being loaded first. Data is clocked in on positive going clock (CLK) edges and is latched into the DAC input register on negative going latch enable (LE) edges. INSTALLATION AND OPERATING INSTRUCTIONS POWER SUPPLY CONNECTIONS For optimum performance and noise rejection, power supply decoupling capacitors should be added as shown in the Connection Diagram. These capacitors (1µF tantalum or electrolytic recommended) should be located close to the converter. The latch enable input must be high for at least one clock cycle before going low, and then must be held low for at least one clock cycle. The last 16 data bits clocked into the serial input register are the ones that are transferred to the DAC input register when latch enable goes low. In other words, when more than 16 clock cycles occur between a latch enable, only the data present during the last 16 clocks will be transferred to the DAC input register. MSB ERROR ADJUSTMENT PROCEDURE (OPTIONAL) The MSB error of the PCM56 can be adjusted to make the differential linearity error (DLE) at BPZ essentially zero. This is important when the signal output levels are very low, because zero crossing noise (DLE at BPZ) becomes very significant when compared to the small code changes occurring in the LSB portion of the converter. One requirement for clocking in all 16 bits is the necessity for a “17th” clock pulse. This automatically occurs when the clock is continuous (last bit shifts in on the first bit of the next data word). If the clock is stopped between input of 16bit data words, the latch enable (LE) must remain low until after the first clock of the next 16-bit data word stream. This ensures that the latch is properly set up. Differential linearity error at bipolar zero and THD are guaranteed to meet data sheet specifications without any external adjustment. However, a provision has been made for an optional adjustment of the MSB linearity point which makes it possible to eliminate DLE error at BPZ. Two procedures are given to allow either static or dynamic adjustment. The dynamic procedure is preferred because of the difficulty associated with the static method (accurately measuring 16-bit LSB steps). Figure 7 refers to the general input format required for the PCM56. Figure 8 shows the specific relationships between the various signals and their timing constraints. INSTALLATION CONSIDERATIONS To statically adjust DLE at BPZ, refer to the circuit shown in Figure 6, or the PCM56 connection diagram. If the optional external MSB error circuitry is used, a potentiometer with adequate resolution and a TCR of 100ppm/ °C or less is required. Also, extra care must be taken to insure that no leakage path (either AC or DC) exists to pin 14. If the circuit is not used, pins 14 and 15 should be left open. After allowing ample warm-up time (5-10 minutes) to assure stable operation of the PCM56, select input code FFFF hexadecimal (all bits on except the MSB). Measure the audio output voltage using a 6-1/2 digit voltmeter and record it. Change the digital input code to 0000 hexadecimal (all bits off except the MSB). Adjust the 100kΩ potentiometer to make the audio output read 92µV more than the voltage reading of the previous code (a 1LSB step = 92µV). The PCM converter and the wiring to its connectors should be located to provide the optimum isolation from sources of RFI and EMI. The important consideration in the elimination ® PCM56 6 (1) Clock LSB MSB Data 1 (2) 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 MSB Latch Enable (3) (4) NOTES: (1) If clock is stopped between input of 16-bit data words, latch enable (LE) must remain low until after the first clock of the next 16-bit data word stream. (2) Data format is binary two's complement (BTC). Individual data bits are clocked in on the corresponding positive clock edge. (3) Latch enable (LE) must remain low at least one clock cycle after going negative. (4) Latch enable (LE) must be high for at least one clock cycle before going negative. FIGURE 7. Input Timing Diagram. source and drain of the FET switch operate at a virtual ground when “C” and “B” are connected in the sample mode, there is no increase in distortion caused by the modulation effect of RON by the audio signal. > 40ns Data Input LSB MSB Figure 10 shows the deglitcher controls for both left and right channels which are produced by timing control logic. A delay of 1.5µs (tω) is provided to allow the output of the PCM56 to settle within a small error band around its final value before connecting it to the channel output. Due to the fast settling time of the PCM56 it is possible to minimize the delay between the left- and right-channel outputs when using a single D/A converter for both channels. This is important because the right- and left-channel data are recorded in-phase and the use of the slower D/A converter would result in significant phase error at higher frequencies. >15ns >15ns Clock Input > 40ns > 40ns > 5ns > 100ns Latch Enable > 15ns > One Clock Cycle > One Clock Cycle The obvious solution to the phase shift problem in a twochannel system would be to use two D/A converters (one per channel) and time the outputs to change simultaneously. Figure 11 shows a block diagram of the final test circuitry used for PCM56. It should be noted that no deglitching circuitry is required on the DAC output to meet specified THD performance. This means that when one PCM56 is used per channel, the need for all the sample/hold and controls circuitry associated with a single DAC (two-channel) design is effectively eliminated. The PCM56 is tested to meet its THD specifications without the need for output deglitching. FIGURE 8. Input Timing Relationships. of RF radiation or pickup is loop area; therefore, signal leads and their return conductors should be kept close together. This reduces the external magnetic field along with any radiation. Also, if a signal lead and its return conductor are wired close together, they represent a small flux-capture cross section for any external field. This reduces radiation pickup in the circuit. APPLICATIONS A low-pass filter is required after the PCM56 to remove all unwanted frequency components caused by the sampling frequency as well as those resulting from the discrete nature of the D/A output. This filter must have a flat frequency response over the entire audio band (0-20kHz) and a very high attenuation above 20kHz. Figures 9 and 10 show a circuit and timing diagram for a single PCM56 used to obtain both left- and right-channel output in a typical digital audio system. The audio output of the PCM56 is alternately time-shared between the left and right channels. The design is greatly simplified because the PCM56 is a complete D/A converter requiring no external reference or output op amp. Most previous digital audio circuits used a higher order (913 pole) analog filter. However, the phase response of an analog filter with these amplitude characteristics is nonlinear and can disturb the pulse-shaped characteristic transients contained in music. A sample/hold (S/H) amplifier, or “deglitcher” is required at the output of the D/A for both the left and right channel, as shown in Figure 9. The S/H amplifier for the left channel is composed of A1, SW1, and associated circuitry. A1 is used as an integrator to hold the analog voltage in C1. Since the ® 7 PCM56 SECOND GENERATION SYSTEMS One method of avoiding the problems associated with a higher order analog filter would be to use digital filter oversampling techniques. Oversampling by a factor of two would move the sampling frequency (88.2kHz) out to a point where only a simple low-order phase-linear analog filter is required after the deglitcher output to remove unwanted intermodulation products. In a digital compact disc application, various VLSI chips perform the functions of error detection/correction, digital filtering, and formatting of the digital information to provide the clock, latch enable, and serial input to the PCM56. These VLSI chips are available from several sources (Sony, Yamaha, Signetics, etc.) and are specifically optimized for digital audio applications. Oversampled circuitry requires a very fast D/A converter since the sampling frequency is multiplied by a factor of two or more (for each output channel). A single PCM56 can provide two-channel oversampling at a 4X rate (176.4kHz/ channel) and still remain well within the settling time requirements for maintaining specified THD performance. This would reduce the complexities of the analog filter even further from that used in 2X oversampling circuitry. R2 2.2kΩ R1 2.2kΩ C C1 680pF Serial Data A Clock B SW1 PCM56 A1(1) Left Channel Output to LPF MP7512 (Micro Power) Latch Enable R4 2.2kΩ R3 2.2kΩ Left Channel Deglitcher Control Right Channel Deglitcher Control C A B SW2 A "low" signal on the deglitcher control closes switch "A", while a "high" signal closes switch "B". C2 680pF A2(1) Right Channel Output to LPF MP7512 (Micro Power) NOTE: (1) 1 OPA101AM or 1/4 OPA404KP or 1 OPA606KP or OPA2604. FIGURE 9. A Sample/Hold Amplifier (Deglitcher) is Required at the Digital-to-Analog Output for Both Left and Right Channels. 44.1kHz Serial Data Left Channel Right Channel Left Channel Right Channel Latch Enable tω = 1.5µs DAC Settling Time Right Channel Deglitcher Control Left Channel Deglitcher Control t DELAY 4.5µs max The deglitcher control signals by timing control logic. The fast settling time of the PCM56 makes it possible to minimize the delay between left and right channels to about 4.5µs, which reduces phase error at the higher audio frequencies. FIGURE 10. Timing Diagram for the Deglitcher Control Signals. ® PCM56 8 Low-Pass Filter (Toko APQ-25 or Equivalent) Programmable Gain Amp 0dB to 60dB Distortion Analyzer (Shiba Soku Model 725 or Equivalent) 0 LOW-PASS FILTER CHARACTERISTIC –20 Gain (dB) Use 400Hz High-Pass Filter and 30kHz Low-Pass Filter Meter Settings –40 –60 –80 –100 Binary Counter Digital Code (EPROM) Parallel-to-Serial Conversion DUT (PCM58P) –120 1 1 2 3 4 5 10 10 10 10 10 Frequency (Hz) Clock Latch Enable Timing Logic Sampling Rate = 44.1kHz x 4 (176.4kHz) Output Frequency = 991Hz FIGURE 11. Block Diagram of Distortion Test Circuit. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® 9 PCM56