MOTOROLA MC44BS374CA

Freescale Semiconductor, Inc.
Technical data
MC44BS374CA
Rev. 1.2 04/2004
MC44BS374CA
Freescale Semiconductor, Inc...
PLL Tuned UHF and
VHF Audio/Video High
Integration Modulator
SO16NB Package
Ordering Information
Device
Temp Range
Package
MC44BS374CAD,R2
0°C to +70°C
SO16NB
0°C to +70°C
SO16NB
Lead free
MC44BS374CAEF,R2
NOTE: For tape and reel, add R2 suffix.
Contents
Features . . . . . . . . . . . . . . . 2
Comparing the
MC44BS374CA to the
MC44BC374C . . . . . . . . 3
Pin Descriptions . . . . . . . . 3
MC44BS374CA Functional
Overview . . . . . . . . . . . . 4
Maximum Ratings . . . . . . . 5
Thermal Ratings . . . . . . . . . 5
Electrostatic Discharge . . . 5
Electrical Characteristics . 6
I2C Bit Mapping . . . . . . . . . 7
I2C Programming . . . . . . . . 8
Modulator High Frequency
Characteristics . . . . . . 10
Video Characteristics . . . 11
Audio Characteristics . . . 13
Characterization
Measurement Conditions
14
MC44BS374CA Modes of
Operation . . . . . . . . . . . 20
High Speed I2C Compatible
Bus . . . . . . . . . . . . . . . . 24
Pin Circuit Schematics . . 27
Application Diagram . . . . 28
MC44BS374CA Evaluation
Board Layout and
Schematic . . . . . . . . . . 29
Packaging Instructions . . 31
Marking Instructions . . . . 31
Case Outline 32
The MC44BS374CA audio and video modulator is for use in VCRs, set-top boxes, and
similar devices.
•
Multi standard
•
TV output level 82dBuV typical
•
5V and 3.3V compatible I2C bus
Figure 1 shows the pin connections.
SCL
1
16
GNDD
SDA
2
15
VCCD
LOP
XTAL
3
14
PLLFLT
4
13
TVOVCC
GND
5
12
TVOUT
PREEM
6
11
GND
AUDIO
7
10
VCCA
SPLFLT
8
9
VIDEO
SO16 pin package
Figure 1. MC44BS374CA Pin Connections
This document contains information on a product under development. Motorola reserves the right to change or
discontinue this product without notice. © Motorola, Inc., 2003. All rights reserved.
For More Information On This Product,
Go to: www.freescale.com
Features
Freescale Semiconductor, Inc.
1 Features
The MC44BS374CA is a Multi-Standard, PAL/NTSC Modulator.
The channel is set by an on-chip high-speed I2C compatible bus receiver. A Phase-Locked Loop ( PLL )
tunes the modulator over the full UHF range.
The modulator incorporates a sound subcarrier oscillator and uses a second PLL to derive 4.5, 5.5, 6.0,
and 6.5 MHz subcarrier frequencies. These frequencies are selectable by bus.
The picture-to-sound ratio may be adjusted using the bus. In addition, an on-chip video test pattern
generator can be switched ON with a 1 KHz audio test signal.
Freescale Semiconductor, Inc...
The MC44BS374CA also has the following features:
2
•
Integrated on-chip programmable UHF oscillator
•
No external varicaps diodes / inductor or tuned components
•
Extremely low external components count
•
Channel 21-69 UHF operation
•
VHF range possible by internal dividers (30MHz-450MHz)
•
Boosted TVout level (82 dBuV typical)
•
High speed read and write I2C-bus compatible (800kHz)
•
I2C-bus 5V and 3.3V compatible
•
Fixed video modulation depth (82% typical)
•
Peak White Clip disabled by bus
•
Programmable picture/sound carrier ratio (12dB and 16dB)
•
Integrated on-chip programmable sound subcarrier oscillator (4.5, 5.5, 6.0 and 6.5 MHz) - No
external varicaps
•
On-chip video test pattern generator with sound test signal (1kHz)
•
Low-power programmable modulator standby mode
•
Transient output inhibit during PLL Lock-up at power-ON
•
Logical Output Port controlled by bus
•
ESD protection, minimum 4 kV
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor,
Inc. to the MC44BC374C
Comparing the MC44BS374CA
2 Comparing the MC44BS374CA to the MC44BC374C
Freescale Semiconductor, Inc...
Compared to the MC44BC374C devices, the MC44BS374CA has the following improvements:
•
Higher output level (82 dBuV versus 74.5 dBuV)
•
Higher Video signal to noise (+ 3 dB)
•
I2C-bus 3.3V compatible
•
Lower power consumption in normal and standby modes (-2 mA)
•
The device can be powered down without holding the I2C lines down.
•
TB1 bit is no more available (limited compatibility with MC44355 devices no more available)
•
Switch between the two integrated VCO’s controlled directly by the frequency divider (@ 700
MHz)
3 Pin Descriptions
Table 1. Package Pin Descriptions
MOTOROLA
Pin number
Pin Name
Description
1
SCL
I2C clock
2
SDA
I2C data
3
LOP
Logical output port controlled by I2C bus
4
XTAL
Crystal
5
GND
Ground
6
PREEMP
7
AUDIO
Audio input
8
SPLFLT
Sound PLL loop filter
9
VIDEO
Video input
10
VCCA
Main analog supply voltage
11
GND
Analog ground
12
TVOUT
13
TVOVCC
14
PLLFLT
15
VCCD
Digital supply voltage
16
GNDD
Digital ground
Pre-emphasis capacitor
TV output signal
TV output stage supply voltage
RF PLL loop filter
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
3
MC44BS374CA FunctionalFreescale
Overview
Semiconductor, Inc.
4 MC44BS374CA Functional Overview
Figure 2 shows a simplified block diagram of the MC44BS374CA device.
The MC44BS374CA device has three main sections:
1. A high speed I2C-compatible bus section
2. A PLL section to synthesize the UHF / VHF output channel frequency (from an integrated
UHF oscillator, divided for VHF output)
3. A modulator section, which accepts audio and video inputs, then uses them to modulate the
UHF/VHF carrier
An on-chip video test pattern generator with an audio test signal is included.
High frequency BiCMOS technology allows integration of the UHF tank circuit and certain filtering
functions.
LOP
3
VIDEO
9
Peak
White
Clip
I2C BUS
Video
Modulator
TVOVCC 13
TVOUT 12
I2C BUS
LPF
SPLLFLT
8
MODULATOR
SECTION
Clamp
31.25KHz
LPF
75Ω
I2C BUS
Sound
PFD
Sound
Oscillator
and FM
Modulator
Prog
Divider
LPF
Audio
Amplifier
7
AUDIO
6
PREEM
10 VCCA
ALC
11 GND
5
GND
FM
RF Sound
Modulator
BUS SECTION
SCL
1
SDA
2
High Speed
I2C Bus
Receiver
VHF Dividers
I2C BUS
Freescale Semiconductor, Inc...
The MC44BS374CA operates as a multi-standard modulator and can handle the following systems using
the same external circuit components: B / G, I, D / K, M / N.
UHF OSC
Prescaler/8
Prog
Divider
VCO and PLL SECTION
PLL
Phase
Comp
I2C BUS
Ref Divider
/128
4MHz
XCO
31.25KHz
15
16
14
VCCD
GNDD
PLLFLT
4
XTAL
Figure 2. MC44BS374CA Simplified Block Diagram
4
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Maximum Ratings
5 Maximum Ratings
Sym
Parameter
Vcc
Value Unit
Supply voltage
6
V
Tamin
Minimum operating ambient temperature
0
o
Tamax
Maximum operating ambient temperature
+70
o
Tstgmin Minimum storage temperature
-65
oC
Tstgmax Maximum storage temperature
150
o
150
oC
C
This device contains protection circuitry to guard
against damage due to high static voltage or electric
fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated
Tj
Junction Temperature
C
C
voltages to this high impedance circuit. For proper
operation, input and output voltages should be
constrained to the ranges indicated in the
Recommended Operating Conditions.
Freescale Semiconductor, Inc...
Note: Maximum ratings are those values beyond which damage to the device may occur. For functional operation,
values should be restricted to the Recommended Operating Condition.
Note:
Meets Moisture Sensitivity Level 1, no dry pack required.
6 Thermal Ratings
Sym
Rthja
Parameter
Thermal resistance from Junction to Ambient
Value
Unit
102
°C/W
Min
Unit
7 Electrostatic Discharge
Electrostatic Discharge ( ESD ) tests are done on all pin
s
Sym
Parameter
ESD
MM (Machine Model) - MIL STD 883C method 3015-7
400
V
ESD
HBM (Human Body Model) - MIL STD 883C method 3015-7
4000
V
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
5
Electrical Characteristics
Freescale Semiconductor, Inc.
8 Electrical Characteristics
•
A = 100% tested
•
B = 100% Correlation tested
•
C = Characterized on samples
•
D = Design parameter
See Characterization conditions section for each C type parameter.
8.1 Operating Conditions
Unless otherwise stated: Vcc=5.0 V, Ambient Temperture=25o C, Video Input 1Vp-p, 10-step grayscale.
RF output into 75 Ohm load.
Freescale Semiconductor, Inc...
NOTE:
Specifications only valid for envelope demodulation.
Table 2. Operating Conditions
Parameter
Min
Typ
Max
Unit
Operating supply voltage range
4.5
5.0
5.5
V
Total supply current
42
50
58
mA
All sections active
A
Total standby mode supply current
3
5
7
mA
OSC, SO, ATT = 1
Bus Section active
A
Test pattern sync pulse width
3
4.7
6.5
µS
B
Sound comparator charge pump current
During locking
When locked
7
0.7
10
1
12
1.5
µA
µA
A
A
RF comparator charge pump current
60
100
150
µA
A
Crystal oscillator stability-negative
resistance
1
-
-
KΩ
D
-
160
-
300
1
mV
µA
A
A
Logic Output Port
Saturation voltage at I = 2 mA
Leakage current
6
Notes
Type
B
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
I2C Bit Mapping
9 I2C Bit Mapping
WRITE MODE
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ACK
CA-CHIP ADDRESS
1
1
0
0
1
0
1
0
ACK
C1-High Order Bits
1
0
SO
LOP
PS
X3
X2
0
ACK
C0-Low Order Bits
PWC
OSC
ATT
SFD1
SFD0
0
X5
X4
ACK
FM-High Order Bits
0
TPEN
N11
N10
N9
N8
N7
N6
ACK
FL-Low Order Bits
N5
N4
N3
N2
N1
N0
X1
X0
ACK
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ACK
CHIP ADDRESS
1
1
0
0
1
0
1
1
ACK
R-Status Byte
-
-
-
-
-
Y2
Y1
OOR
-
READ MODE
Freescale Semiconductor, Inc...
Bit Name
Description
PWC
Peak White Clip enable / disable
OSC
UHF oscillator ON / OFF
ATT
Modulator output attenuated-sound and video modulators ON / OFF
SFD0, 1
Sound subcarrier frequency control bits
SO
Sound Oscillator ON / OFF
LOP
Logic Output Port
PS
TPEN
X5…X0
N0…N11
OOR
Y1, Y2
MOTOROLA
Picture-to-sound carrier ratio
Test pattern enable-picture and sound
Test mode bits-All bits are 0 for normal operation (see Test Mode tables, page 6 & page 7)
UHF frequency programming bits, in steps of 250 kHz
RF oscillator out-of-frequency range information
RF oscillator operating range information
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
7
Freescale Semiconductor, Inc.
I2C Programming
10 I2C Programming
Sound
UHF
SFD 1
SFD 0
Sound Subcarrier Freq (MHz)
OSC
UHF Oscillator
0
0
4.5
0
Normal operation
0
1
5.5
1
1
0
6.0
UHF oscillator disabled (oscillator and PLL
sections bias turned OFF)
1
1
6.5
Freescale Semiconductor, Inc...
ATT
PS
Picture-to-Sound Ratio (dB)
0
12
1
16
SO
Sound Oscillator
0
Sound oscillator ON (Normal mode)
1
Sound oscillation disabled (oscillator and PLL
section bias turned OFF)
Video
Modulator Output Attenuation
0
Normal operation
1
Modulator output attenuation (sound and
video modulators sections bias turned OFF.
Standby Mode
OSC
SO
ATT
1
1
1
Combination of 3-bits
Modulator standby mode
Logic Output Port
PWC
Peak White Clip
0
Peak White Clip ON (System B / G)
1
Peak White Clip OFF (System L)
TPEN
LOP
Description
0
Pin 3 is low voltage
1
Pin 3 is high impedance
Test Pattern Signal
0
Test pattern signal OFF (normal operation)
1
Test pattern signal ON (picture and sound)
WRITE MODE: Test Mode 1 and VHF Range
8
X2
X1
X0
State
Description
0
0
0
1.a
Normal operation
0
0
1
1.b
RF frequency divided for low frequency testing or VHF range: RF / 2
0
1
0
1.c
RF / 4
0
1
1
1.d
RF / 8
1
0
0
1.e
RF / 16
1
0
1
1.f
DC drive applied to modulators: Non-inverted video at TVOUT
1
1
0
1.g
DC drive applied to modulators: Inverted video at TVOUT
1
1
1
1.h
Transient output inhibit disabled (ie speed up mode)
During this speed-up test mode, ATT=0 forces sound current source to 1µA, and
ATT=1 forces it to 10µA.
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
I2C Programming
Freescale Semiconductor, Inc...
WRITE MODE: Test Mode 2
X5
X4
X3
State
Description
0
0
0
2.a
Normal operation
0
0
1
2.b
Test pattern generator DC verification (Test pattern DC test mode available)
0
1
0
2.c
Program divider test (UHF program divider on PLLFILT pin and sound program
divider on SPLLFIL pin)
0
1
1
2.d
Reference divider test (UHF reference divider on PLLFILT pin)
1
0
0
2.e
UHF phase comparison, upper source on PLLFILT pin
Sound phase comparison 10 µA upper source on SPLLFIL
( Only valid during transient output inhibit. )
1
0
1
2.f
UHF phase comparison, lower source on PLLFILT pin
Sound phase comparison 10 µA lower source on SPLLFIL
( Only valid during transient output inhibit. )
1
1
0
2.g
Sound phase comparison 1 µA upper source on SPLLFIL
( Not valid during transient output inhibit. )
1
1
1
2.h
Sound phase comparison 1 µA lower source on SPLLFIL
( Not valid during transient output inhibit. )
NOTE:
Test modes 1 and 2 are intended for manufacturing test purposes only and
cannot be used for normal applications, except for VHF range (states 1.b
to 1.e).
READ MODE
OOR
Description
0
Normal operation, VCO in range
1
VCO out of range
Y1
Description
0
VCO out of range, frequency too low, only valid if OOR=1
1
VCO out of range, frequency too high, only valid if OOR=1
Y2
Description
0
High VCO is active
1
Low VCO is active
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
9
Modulator High FrequencyFreescale
Characteristics Semiconductor,
Inc.
11 Modulator High Frequency Characteristics
Unless otherwise stated: Vcc=5.0 V, Ambient Temperture=25o C, Video Input 1Vp-p, 10-step grayscale.
RF inputs / outputs into 75 Ohm load.
NOTE:
Specifications only valid for envelope demodulation.
Table 3. High Frequency Characteristics
Parameter
TVOUT output level
Test Conditions
Min
Typ
Max
Unit
Type
Output signal from modulator section
See Figure 3. See Note 2
79
82
85
dBµV
B
460
-
880
MHz
A
Freescale Semiconductor, Inc...
UHF oscillator frequency
VHF range
From UHF oscillator internally divided
45
-
460
MHz
B
TVOUT output attenuation
During transient output inhibit, or
when ATT bit is set to 1. See
Figure 3.
See Note 2
65
75
-
dBc
B
Sound subcarrier harmonics
(Fp + n ∗ Fs)
Reference picture carrier. See Note 2
50
63
-
dBc
C
Second harmonic of chroma
subcarrier
Using red EBU bar. See Note 2
45
70
-
dBc
C
Chroma / Sound intermodulation:
Fp + ( Fsnd - Fchr )
Using red EBU bar.See Note 2
65
82
-
dBc
C
Fo (picture carrier) harmonics
2nd harmonic: CH21
3rd harmonic: CH21
Other channels: See Figure 3.
See NOTE 1. See Note 2
-
38
58
50
70
dBµV
C
Out band (picture carrier)
spurious
1 / 2 ∗ Fo - 1 / 4 ∗ Fo - 3 / 2 ∗ Fo - 3 / 4 ∗ Fo
From 40 MHz to 1 GHz. See Note 2
-
-
10
dBµV
C
In band spurious (Fo @ 5 MHz)
No video sound modulation.See Note
2
65
75
-
dBc
C
Note:
1: Picture carrier harmonics are highly dependant on PCB layout and decoupling capacitors.
Note:
2: See “Characterization Measurement Conditions” on page 14.
10
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
2Fo Harm onics
75
70
70
60
55
50
45
60
55
50
45
Typical
Typical
40
40
35
471
Maximum specification
65
Maximum specification
dBuV
dBuV
3Fo Harm onics
75
65
521
571
621
671
721
771
821
35
471
871
521
571
Frequency (Mhz)
621
671
721
771
821
871
Frequency (Mhz)
TV Output Level
TV Output Attenuation
87
85
Maximum specification
80
85
Typical
75
83
Typical
dBc
dBuV
Freescale Semiconductor, Inc...
Video Characteristics
81
65
Minimum specification
79
77
471
70
Minimum specification
60
521
571
621
671
721
771
821
871
55
471
521
571
621
671
721
771
821
871
Frequency (Mhz)
Frequency (Mhz)
Figure 3. Typical High Frequency Performance
12 Video Characteristics
Unless otherwise stated: Vcc=5.0 V, Ambient Temperature=25o C, Video Input 1Vp-p, 10-step grayscale.
RF output into 75 Ohm load.
NOTE:
Specifications only valid for envelope demodulation.
Table 4. Video Performance Characteristics
Parameter
Test Conditions
Video bandwidth
Reference 0 dB at 100 kHz,
measured at 5 MHz. See Note 2
Video input level
75 Ohm load
Video input current
Video input impedance
Peak White Clip
MOTOROLA
Video Modulation depth for
video=1.4VCVBS
Min
Typ
Max
Unit
Type
-1.5
-0.8
-
dB
C
-
-
1.5
Vcvbs
D
-
0.2
1
µA
A
500
-
-
KΩ
A
90.5
94
97.5
%
B
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
11
Video Characteristics
Freescale Semiconductor, Inc.
Table 4. Video Performance Characteristics
Parameter
Test Conditions
Min
Typ
Max
Unit
Type
Using CCIR Rec.567 weighting filter
See Figure 4. See Note 2
53
56
-
dB
C
Unweighted. See Note 2
48
53
-
Differential Phase
CCIR Test Line 330, worst case from
the first 4 steps out of 5. See Note 2
-5
-
5
deg
C
Differential Gain
CCIR Test Line 330, worst case from
the first 4 steps out of 5. See Note 2
-5
-
5
%
C
Luma / Sync ratio
Input ratio 7.0 : 3.0
6.8 /
3.2
7.0 /
3.0
7.2 /
2.8
-
B
Video modulation depth
See Figure 4. See Note 2
76
82
88
%
B
No sound modulation,100% white video
Note:
C
2: See “Characterization Measurement Conditions” on page 14.
Video Signal to Noise
(w ith CCIR Weighting filter)
62
60
Typical
dB
58
56
54
52
Minimum specification
50
48
471
521
571
621
671
721
771
821
871
Frequency (Mhz)
PAL Video Modulation Depth
90
Maximum specification
88
86
84
%
Freescale Semiconductor, Inc...
Video S / N
Typical
82
80
Minimum specification
78
76
74
471
521
571
621
671
721
771
821
871
Frequency (Mhz)
Figure 4. Typical Video Performance
12
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Audio Characteristics
13 Audio Characteristics
Unless otherwise stated: Vcc=5.0 V, Ambient Temperture=25o C, Video Input 1Vp-p, 10-step grayscale.
RF inputs / outputs into 75 Ohm load.
NOTE:
Specifications only valid for envelope demodulation.
Table 5. Audio Performance Characteristics
Parameter
PS bit set to 0
PS bit set to 1
Min
Typ
Max
Unit
Type
9
13
12
16
15
19
dB
B
Using specific pre-emphasis circuit,
audio input level = 205 mVrms - audio frequency = 1 kHz
Audio modulation depth
FM modulation : Fs = 5.5, 6 or 6.5 MHz
100% modulation = +/-50 kHz FM
deviation
76
80
84
%
B
FM modulation : NTSC Fs = 4.5 MHz
100% modulation = +/-25 kHz FM
deviation
76
80
84
%
B
45
53
61
KΩ
A
-2.0
-
+2.0
dB
C
Audio input resistance
Audio Frequency
response
Reference 0 dB at 1 kHz,
using specified pre-emphasis circuit,
measure from 50 Hz to 15 kHz
Depends on loop filter components
Audio Distortion FM (THD
only)
at 1 kHz, 100% modulation ( ± 50 kHz )
No video
-
0.2
0.8
%
C
Audio S / N with Sync Buzz
FM
Ref 1Khz, 50% modulation (+/-25Khz)
EBU color bars Video signal,
using CCIR 468.2 weighting filter
50
54
-
dB
C
Note:
2: See “Characterization Measurement Conditions” on page 14.
FM Audio Weighted Signal to Noise
58
56
Typical
54
dB
Freescale Semiconductor, Inc...
Picture-to-Sound ratio
Test Conditions
52
50
48
Minimum specification
46
471
521
571
621
671
721
771
821
871
Frequency (Mhz)
Figure 5. Typical Audio Performance
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
13
Freescale
Characterization Measurement
Conditions
Semiconductor, Inc.
14 Characterization Measurement Conditions
Freescale Semiconductor, Inc...
The following list shows the MC44BS374CA default configuration unless otherwise specified.
•
Peak White Clip enabled
•
UHF oscillator ON
•
Sound and video modulators ON
•
Sound subcarrier frequency = 5.5 MHz
•
Sound Oscillator ON
•
Logic Output Port LOW
•
Picture-to-sound carrier ratio = 12 dB
•
Test pattern disabled
•
All test mode bits are ‘0’
•
Frequency from channel 21 to 69
RF Inputs / Output into 75ohm Load using a 75 to 50 ohm transformation. Video Input 1Vpp.
Audio pre-emphasis circuit enabled.
14
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor,
Inc.
Characterization
Measurement Conditions
Table 6. Measurement Conditions
Device and Signals Set-up
Measurement Set-up
TVOUT output level
Measured picture carrier in dBuV with the HP8596E Spectrum
Analyzer using a 75 to 50 ohm transformation, all cables losses and
transformation pads having been calibrated.
Measurement used as a reference for other tests: TVout_Ref
Video: 10 steps grey scale
No audio
Freescale Semiconductor, Inc...
TVOUT output attenuation
Measure in dBc picture carrier at ATT=1 with reference to picture
carrier at ATT=0
ATT” bit = 1
No Video signal
No Audio signal
Sound Subcarrier Harmonics
Video: 10 steps grey scale
No Audio signal
Measure in dBc second and third sound harmonics levels in reference
to picture carrier (TVout_Ref).
Picture carrier
Sound carrier
Sound
2nd harm
Sound
3rd harm
Fo
+5.5MHz
+11MHz +16.5MHz
Second Harmonics of Chroma subcarrier
No audio
Video: a 700m Vpp 100 kHz sinusoidal
signal is inserted on the black level of
active video area.
Frequency
Frequency
100kHz
100Khz
Measure in dBc, in reference to picture carrier (TVout_Ref), second
harmonic of chroma at channel frequency plus 2 times chroma
frequency, resulting in the following spectrum.
Picture carrier
700mVpkpk
Chroma
carrier
700mV pk-pk
Sound
carrier
Chroma 2nd
Harmonic
Fo
MOTOROLA
+4.43MHz +5.5MHz
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
+8.86MHz
15
Freescale
Characterization Measurement
Conditions
Semiconductor, Inc.
Table 6. Measurement Conditions
Device and Signals Set-up
Measurement Set-up
Chroma/Sound Intermodulation
No audio signal
Video: 700m Vpp 100 kHz sinusoidal
signal inserted on the black level of
active video area.This is generated using
a Rohde & Schwarz Video Generator
SAF and inserting the required frequency
from a RF Signal generator.
Frequency
Frequency
100kHz
4.43
MHz
Measure in dBc, in reference to picture carrier (TVout_Ref),
intermodulation product at channel frequency plus the sound carrier
frequency (+5,5 MHz) minus the chroma frequency (-4,43 MHz),
resulting in the following spectrum.
Intermodulation product is at the channel frequency +1,07 MHz.
Picture carrier
700mVpp
Chroma/Sound
Intermod.
700mV pk-pk
Freescale Semiconductor, Inc...
Sound
carrier
Chroma
carrier
Fo
+4.43MHz +5.5MHz
+1.07MHz
Picture Carrier Harmonics
No Video signal
No Audio signal
Measure in dBc, in reference to picture carrier (TVout_Ref), second
and third harmonic of channel frequency, resulting in the following
spectrum.
Picture carrier
3rd harmonic
2nd harmonic
Fo
2Fo
3Fo
Out of Band Spurious
No Video signal
No Audio signal
Measure in dBuV spurious levels at 0.25, 0.5, 0.75 and 1.5 times
channel frequency, resulting in the following spectrum
Measure from 40MHz to 1GHz.
Picture carrier
Spurious
Fo/4
Fo/2 Fo*3/4
Fo
Fo*3/2
In Band Spurious
No Video signal
No Audio signal
16
Measure in dBc, in reference to picture carrier (TVout_Ref), spurious
levels falling into video bandwidth starting from +/-100 KHz from the
picture carrier up to +/-5MHz.
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor,
Inc.
Characterization
Measurement Conditions
Table 6. Measurement Conditions
Device and Signals Set-up
Measurement Set-up
Video Bandwidth
No audio
Video: 600mVpp sinusoidal signal
inserted on the black level of active video
area.
The Video signal is demodulated on the spectrum analyzer, and the
peak level of the 100KHz signal is measured as a reference. The
frequency is then swept from 100KHz to 5MHz, and then the difference
in dB from the 100KHz reference level is measured.
Freescale Semiconductor, Inc...
Weighted Video Signal to Noise
Video: 100% White video signal - 1Vpkpk.
No Audio signal
This is measured using a Rohde &
Schwarz AMFS UHF Demodulator in B/G
(using a CCIR Rec. 567 weighting
network, 100kHz to 5MHz band with
sound trap and envelope detection, and a
Rohde & Schwarz UAF Video Analyzer.
The Video Analyzer measures the ratio between the amplitude of the
active area of the video signal (700mV) and the noise level in Vrms on
a video black level which is show below.
VideoS/N is calculated as 20 x log(700 /N) in dB.
N
noise level in Vrms
Unweighted Video Signal to Noise
Same as above with CCIR filter disabled.
Same as above.
Video Differential Phase
Video: 5 step Grey Scale- 1Vpk-pk.
No Audio signal
This is measured using a Rohde &
Schwarz AMFS UHF Demodulator in B/G
(using a CCIR Rec. 567 weighting
network, 100kHz to 5MHz band with
sound trap, and envelope detection, and
a Rohde & Schwarz UAF Video Analyzer.
On line CCIR 330, the video analyzer DP measure consists of
calculating the difference of the Chroma phase at the black level and
the different chroma subcarrier phase angles at each step of the
greyscale. The largest positive or negative difference indicates the
distortion.
the largest positive or negative difference
DIFF PHASE =
the phase at position 0
* 100%
The video analyzer method takes the worst step from the first 4 steps.
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
17
Freescale
Characterization Measurement
Conditions
Semiconductor, Inc.
Table 6. Measurement Conditions
Device and Signals Set-up
Measurement Set-up
Video Differential Gain
Freescale Semiconductor, Inc...
Video: 5 step Grey Scale- 1Vpk-pk.
No Audio signal
This is measured using a Rohde &
Schwarz AMFS UHF Demodulator in B/G
(using a CCIR Rec. 567 weighting
network, 100kHz to 5MHz band with
sound trap and envelope detection, and a
Rohde & Schwarz UAF Video Analyzer.
On line CCIR 330 shown below, the video analyzer DG measure
consists of calculating the difference of the Chroma amplitude at the
black level and the different amplitudes at each step of the greyscale.
The largest positive or negative difference indicates the distortion.
0
1
3
2
5
4
5-step Greyscale with Chroma subcarrier superimposed
(not to scale), line CCIR 330.
the largest positive or negative difference
DIFF GAIN =
the amplitude at position 0
* 100%
The video analyzer method takes the worst step from the first 4 steps.
Video Modulation Depth
No Audio signal
Video: 10 step grey scale
This is measured using a HP8596E Spectrum Analyzer with a TV
Trigger option, allowing demodulation and triggering on any specified
TV Line. The analyzer is centred on the maximum peak of the Video
signal and reduced to zero Hertz span in Linear mode to demodulate
the Video carrier.
A ( 6-10mV)
A(mV)
B(mV)
B (0.6 - 3mV)
TV Line Demodulated by Spectrum Analyzer-BG standard
The Modulation Depth is calculated as (A-B)/A x 100 in%
Picture to Sound ratio
No Video signal
No Audio Signal
PS” bit set to 0 and 1
Measure in dBc sound carrier in reference to picture carrier
(TVout_Ref) for PS” bit=0 (PS=12dB typical) and for PS” bit=1
(PS=16dB),
Picture carrier
Sound carrier
Fo
18
+5.5Mhz
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor,
Inc.
Characterization
Measurement Conditions
Table 6. Measurement Conditions
Device and Signals Set-up
Measurement Set-up
Audio Modulation Depth - FM Modulation
Video Black Level
Audio signal: 1Khz, 205mVrms.
This is measured using a Rohde &
Schwarz AMFS Demodulator in B/G and
a HP8903A Audio Analyzer at 1kHz
The audio signal 205mV at 1kHz is supplied by the Audio Analyzer,
and the FM demodulated signal deviation is indicated on the
Demodulator in Khz peak.
This value is then converted in% of FM deviation, based on specified
standards.
Freescale Semiconductor, Inc...
Audio Frequency response
Video Black Level
Audio signal: 50Hz to 15KHz, 100mVrms
This is measured using a Rohde &
Schwarz AMFS Demodulator in B/G and
a HP8903A.
The audio signal 1KHz 100mVrms is supplied by the Audio Analyzer,
demodulated by the Demodulator and the audio analyzer measures
the AC amplitude of this demodulated audio signal: this value is taken
as a reference (0dB).
The audio signal is then swept from 50Hz to 15KHz, and demodulated
AC amplitude is measured in dB relative to the 1KHz reference.
Audio pre-emphasis and de-emphasis circuits are engaged, all audio
analyzer filters are switched OFF.
Audio Distortion FM
Audio: 1Khz, adjustable level
Video Black Level
This is measured using a Rohde &
Schwarz AMFS UHF Demodulator in B/G
and a HP8903A Audio Analyzer at 1kHz.
The output level of the Audio analyzer is
varied to obtain a deviation of 50kHz
indicated on the Demodulator.
The input arms detector of the Audio Analyzer converts the ac level of
the combined signal + noise + distortion to dc. It then removes the
fundamental signal (1kHz) after having measured the frequency. The
output rms detector converts the residual noise + distortion to dc. The
dc voltmeter measures both dc signals and calculates the ratio in% of
the two signals.
ADist = ( Distorsion + Noise ) ⁄ ( Distorsion + Noise + Signal )
Audio Signal to Noise
Audio: 1Khz, adjustable level
Video: EBU Color Bars
This is measured using a Rohde &
Schwarz AMFS Demodulator in B/G and
a HP8903A Audio Analyzer at 1kHz. The
output level of the Audio analyzer is
varied to obtain a Modulation Deviation of
25kHz indicated on the AMFS
Demodulator.
The Audio Analyzer alternately turns ON and OFF it's internal audio
source to make a measure of the Audio signal plus noise and then
another measure of only the noise.
The measurement is made using the internal CCIR468-2 Filter of the
Audio Analyzer together with the internal 30+/-2kHz (60dB/decade)
Lowpass filters.
The AMFS demodulator uses a quasi-parallel demodulation as is the
case in a normal TV set. In this mode the Nyquist filter is bypassed and
the video carrier is used without added delay to effectuate intercarrier
conversion. In this mode the phase noise information fully cancels out
and the true S/N can be measured.
ASN ( dB ) = 20 × log ( Signal + Noise ) ⁄ ( Noise )
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
19
Freescale
MC44BS374CA Modes of Operation
Semiconductor, Inc.
15 MC44BS374CA Modes of Operation
15.1 Power ON Settings
At power-ON, the MC44BS374CA is configured as follows:
Table 7. Power ON Settings
Freescale Semiconductor, Inc...
WRITE MODE
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ACK
C1-High Order Bits
1
0
0
0
0
0
0
0
ACK
C0-Low Order Bits
0
0
0
0
1
0
0
0
ACK
FM-High Order Bits
0
0
N11
N10
N9
N8
N7
N6
ACK
FL-Low Order Bits
N5
N4
N3
N2
N1
N0
0
0
ACK
Note:
N0 to N11 are set to have UHF oscillator on channel E36 ( 591.25 MHz ).
Note:
Peak White Clip is ON.
Note:
Sound frequency is 5.5 MHz.
Note:
Logic Output Port is low voltage.
Note:
Picture to sound ratio is 12 dB.
15.2 Power Supply
The three device Vccs (pins 10, 13 and 15) must be applied at the same time to ensure all internal blocks
are correctly biased. Do not bias any other pin before Vcc is applied to the MC44BS374CA.
When all Vccs are switched to 0V, SDA and SCL pins are high impedance.
15.3 Standby modes
During standby mode, the modulator is switched to low power consumption. That is, the sound oscillator,
UHF oscillator, and the video and sound modulator section’s bias are internally turned OFF.
The I2C bus section remains active.
The MC44BS374CA can be set to standby mode with a combination of 3 bits: OSC=1, SO=1 and ATT=1
15.4 Transient Output Inhibit
To minimize the risk of interference to other channels while the UHF PLL is acquiring a lock on the
desired frequency, the Sound and Video modulators are turned OFF during a time out period for each of
the following two cases:
•
Power-ON from zero ( i.e., all Vcc is switched from 0 V to 5 V ).
•
UHF oscillator power-ON from OFF state ( i.e., OSC bit is switched from 1 to 0 )
There is a time-out of 263ms until the output is enabled. This lets the UHF PLL settle to its programmed
frequency. During the 263ms time-out, the sound PLL current source is set to 10 µA typical to speed up the
locking time. After the 263ms time-out, the current source is switched to 1 µA. Use care when selecting
loop filter components, to ensure the loop transient does not exceed this delay.
20
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor,
Inc. Modes of Operation
MC44BS374CA
For test purposes, it is possible to disable the 263ms delay using Test Mode 1-State 1.h (this is called speed
up mode).
15.5 UHF Oscillator-VHF range
The UHF oscillator is fully integrated and does not require any external components.
For low frequency testing or VHF range operation ( test mode 1, states 1.b to 1.e ), the UHF oscillator can
be internally divided by: 2, 4, 8, or 16.
15.6 UHF PLL Section
Freescale Semiconductor, Inc...
The reference divider is a fixed divide-by-128, resulting in a reference frequency of 31.25 KHz with a
4.0 MHz crystal.
The prescaler is a fixed divide-by-8 and is permanently engaged.
The programmable divider division-ratio is controlled by the state of control bits N0 to N11.
The divider-ratio N for a desired frequency F (in MHz) is given by:
F 128
N = --- × --------8
4
with:
N = 2048 × N11 + 1024 × N10 + …… + 4 × N2 + 2 × N1 + N0
NOTE:
Programming a division-ratio N=0 is not allowed.
15.7 Logic Output Port (LOP)
The LOP pin controls any logic function. The primary applications for the LOP are to control an external
attenuator or an external switch, between the antenna input and TV output. A typical attenuator application
with PIN diode is shown in Figure 6. The LOP pin switches the PIN attenuator depending on the signal
strength of the Antenna Input. This reduces the risks of intermodulation in certain areas. The LOP can also
be used as an OFF position bypass switch or for other logic functions in the application.
Vcc
Antenna
Input
TV Out
LOP pin
Figure 6. Typical Attenuator Application with Pin Diode
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
21
Freescale
MC44BS374CA Modes of Operation
Semiconductor, Inc.
15.8 Video Section - Peak White Clip
The MC44BS374CA requires the following for proper video functionality:
•
A composite video input with negative going sync pulses
•
A nominal level of 1 Vpp
This signal is AC-coupled to the video input where the sync tip level is clamped.
The video signal is then passed to a Peak White Clip (PWC) circuit. The PWC circuit function soft-clips
the top of the video waveform, if the sync tip amplitude to peak white clip goes too high. This avoids
carrier over-modulation by the video. Clipping can be disabled by software.
Freescale Semiconductor, Inc...
15.9 Test Pattern Generator
The I2C generates a simple test pattern, which can be switched under bus control to permit a TV receiver to
easily tune to the modulator output. The pattern consists of two white vertical bars on a black background
and a 976 Hz audio test signal.
TE2
7/10
3/10
TE1
0
10
20 24 2830
40 44
50
60 64
TIME IN µS.
Figure 7. Test Pattern Generator
22
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor,
Inc. Modes of Operation
MC44BS374CA
15.10 Sound Section
The oscillator is fully integrated and does not require any external components. An internal low-pass filter
and matched structure provide very low harmonics levels.
The sound modulator system consists of an FM modulator incorporating the sound subcarrier oscillator.
The audio input signal is AC-coupled into the amplifier, which then drives the modulator. The audio preemphasis circuit is a high-pass filter with an external capacitor and an internal resistor ( 106 K Ohms
typical ).
The recommended capacitor value for BG standard (with a time constant of 50 µS) is 470 pF.
Freescale Semiconductor, Inc...
The recommended capacitor value for M/N standard (with a time constant of 75 µS) is 750 pF.
To increase the audio bandwidth at low frequencies it is possible to change the sound PLL loop filter. The
recommended values are 220 nF and 22 nF. To increase the bandwidth at low frequencies (lower than 50
Hz), it is possible to use larger loop filter capacitor values. This will give a lower cut off frequency. In this
case it is necessary to calcultate the new values of the loop filter according to the required Q factor and
loop bandwidth. This is described in the following figure.
Sound PLL loop filter calculation
Loop filter equation :
ωo =
Kpd * Kosc
1
, Q=
, with :
N * C1
R * C1 * ωo
ωo = 3dB cut off frequency
Kpd = 1uA : Phase detector current
Kosc = 5MHz/V : sound oscillator slope (in fact Kosc=40MHz/prescaler divider
=8) This provides 5 MHz/V
N = sound divider ratio
Q = quality factor
C2, added to minimize glitches, is usually set to one tenth the size of C1.
Example :
Fref=31.25KHz
N=5.5MHz / 31.25KHz = 176
Assuming C1= 220 nF, then ωo = 360 rad, and fo= 57Hz
Q depends on the desired frequency response ; Choosing Q = 0.7 as a starting point,
then R= 18 kΩ. The resistance acts directly on the factor quality and can be adjusted to
create peaking on the low frequency range. It is recommended to adjust the value of R
experimentally depending on the application and requirements. In the proposed
application schematic a value of 15 18 kΩ has been chosen.
Figure 8. Sound PLL Loop Filter Calculation
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
23
Freescale
High Speed I2C Compatible
Bus
Semiconductor, Inc.
16 High Speed I2C Compatible Bus
16.1 Specification Conditions
Unless otherwise specified, Vcc = 5.0 V, TA = 25 oC.
Electrical Characteristics
Symbol
Freescale Semiconductor, Inc...
SDA / SCL output current at 0 V
Min
Typ
Max
Unit
Type
-5
-2
-
µA
A
SDA / SCL low input level
VIL
-
-
1.5
V
B
SDA / SCL high input level
VIH
2.1
-
-
V
B
SDA/SCL input current for input level from 0.4V to 0.3Vcc
-5
-
5
µA
C
SDA/SCL input level
0
-
Vcc+0,3
V
D
SDA/SCL capacitance
-
-
10
pF
C
ACK low output level (3 mA sinking current)
-
-
0.3
V
C
ACK low output level (9 mA sinking current)
-
-
0.8
V
C
Min
Typ
Max
Unit
Type
0
-
800
kHz
C
Tbuf
200
-
-
ns
C
Setup time for start condition
Tsu;sta
500
-
-
ns
C
Hold time for start condition
Thd;sta
500
-
-
ns
C
Data setup time
Tsu;dat
0
-
-
ns
C
Data hold time
Thd;dat
0
-
-
ns
C
Setup time for stop condition
Tsu;sto
500
-
-
ns
C
Hold time for stop condition
Thd;sto
500
-
-
ns
C
Acknowledge propagation delay
Tack;low
-
-
300
ns
C
SDA fall time at 3ma sink I and 130pF load
-
-
50
ns
C
SDA fall time at 3ma sink I and 400pF load
-
-
80
ns
C
SDA rise time
SCL fall/rise time
-
-
300
300
ns
ns
C
C
Pulse width of spikes suppressed by the input filter
-
-
50
ns
C
Timing Characteristics
Symbol
Bus clock frequency
Bus free time between stop and start
16.2 Timing Definitions
Tbuf
Stop
ACK
Start
Chip Address
SSDA
SSCL
Tsu;sto Thd;sta
...
...
Tsu;dat
Thd;dat
Start
Stop
SDA
SDA
SCL
SCL
Tack:low
Tsu;sta
Thd;sto
Figure 9. SSDA/SSCL Timing
24
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor,
Inc.
High
Speed I2C Compatible Bus
16.3 Level Definitions
SDA/SCL high and low levels are designed to be compatible with 0-5V and 0-3.3V SDA / SCL signals.
SDA
...
Vcc
Vih
dead band
Vil
0V
Figure 10. SDA/SCL Levels
16.4 High Speed I2C Compatible Bus Format
Freescale Semiconductor, Inc...
SCL
1
STA
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19
Chip Address ($CA)
First Data Byte (C1 or FM)
ACK
44 45
Stop
Data
ACK
ACK
SDA
Figure 11. I2C Bus Timing
16.5 I2C Write Mode Format and Bus Receiver
The bus receiver operates the I2C compatible data format. The chip address ( I2C bus ) is as follows.
Table 8. Chip Address (I2C Bus)
1 1 0 0 1 0 1 0 (ACK) = $CA ( hex ) in write mode
In write mode, each ninth data bit ( bits 9, 18, 27, 36, and 45 ) is an acknowledge bit (ACK) during which
the MCU sends a logic 1 and the Modulator circuit answers on the data line by pulling it low. Besides the
chip address, the circuit needs two or four data bytes for operation. The following sequences of data bytes
are the permitted incoming information:
Table 9. Permitted Data Bytes (Incoming Information)
Example 1
STA
CA
C1
C0
STO
Example 2
STA
CA
FM
FL
STO
Example 3
STA
CA
C1
C0
FM
FL
STO
Example 4
STA
CA
FM
FL
C1
C0
STO
Note:
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
25
Freescale
High Speed I2C Compatible
Bus
Semiconductor, Inc.
Table 9. Permitted Data Bytes (Incoming Information)
STA = Start condition
CA = Chip Address
FM = Frequency information, high order bits
FL = Frequency information, low order bits
C1 = Control information, high order bits
CO = Control information, low order bits
STO = Stop condition
Freescale Semiconductor, Inc...
After the chip address, two or four data bytes may be received.
•
If three data bytes are received, the third one is ignored.
•
If five or more data bytes are received, the fifth and following ones are ignored, and the last ACK
pulse is sent at the end of the fourth data byte.
The first and third data bytes contain a function bit, which lets the IC distinguish between frequency
information and control information. If the function bit is a logic 1, the two following bytes contain control
information. The first data byte after the chip address, may be byte CO or byte FM. The two bytes of
frequency information are preceded by a logic 0.
16.6 I2C Read Mode Format
The chip address ( I2C ) is:
Table 10. Chip Address (I2C Read Mode)
1 1 0 0 1 0 1 1 (ACK) = $CB ( hex ) in read mode
The incoming information consists of the read mode chip address byte. The device then answers with an
ACK followed by one byte containing three bits of status information. No acknowledge is answered by the
modulator after this byte.
26
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc. Pin Circuit Schematics
17 Pin Circuit Schematics
VCCD
VCCD
VCC
VCC
50
SDA
25K
25K
SCL
1/2 VCCD
1/2 VCCD
ACK
VCC
VCC
5K
LOP
XTAL
Freescale Semiconductor, Inc...
1.5K
VCC
50k
VCC
PREM
10k
11.8k
AUDIO IN
audio
VCC
VCC
TV OUT
VCC
5K
VCC
SPLLFLT
75
TVOVCC
VCC
VCC
VCC
100
PLLFLT
2K
10K
500
VIDEO
10K
Figure 12. Pin Circuit Schematics
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
27
Application Diagram
Freescale Semiconductor, Inc.
18 Application Diagram
This document contains information on a new product under development.
Motorola reserves the right to change or discontinue this product without notice.
Vcc
SDA SCL
O
O
O
Note 2
1
SCL
2
SDA
O
LOP
Cx
Note 1
4
XTAL
5
GND
Pre-em
6
470pF
PREEM
7
AUDIO
8
SPLLFLT
220nF
100nF
22nF
O
Freescale Semiconductor, Inc...
4MHz
3
LOP
Audio
15K
16
2.2k
22nF
GNDD
15
VCCD
14
Note 3
PLLFLT
13
TVOVCC
12
47nF
10nF
O TVOUT
1nF
TVOUT
11
GND
10
Note 3
10nF
VCCA
9
VIDEO
10nF
100nF
75
O
Video
O
Vcc
Figure 13. Proposed SO16 Package (Mono Application Schematic)
Note:
1. Cx value depends on crystal characteristics. Cx = 27 pF on Motorola application board.
Note:
2. RF PLL Loop Filter components at pin 14 must be as close as possible to Vccd at pin 15.
Note:
3. Supply voltage decoupling capacitors must be as close as possible to ground.
28
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale MC44BS374CA
Semiconductor,
Evaluation Inc.
Board Layout and Schematic
19 MC44BS374CA Evaluation Board Layout and Schematic
Freescale Semiconductor, Inc...
19.1 Evaluation Board Layout
Figure 14. Evaluation Board PCB Layout
MOTOROLA
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
29
Semiconductor,
MC44BS374CA EvaluationFreescale
Board Layout and
Schematic
Inc.
Freescale Semiconductor, Inc...
19.2 Evaluation Board Schematic
Figure 15. Evaluation Board Schematic
30
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.Packaging Instructions
20 Packaging Instructions
Tape and reel packaging per 12MRH00360A issue Y with the following conditions applicable for Dual InLine SOP (SOIC) package. For lead free package meets Moisture Sensitivity Level 3 (dry pack required).
Freescale Semiconductor, Inc...
Figure 16. Dual In-line SOP (SOIC)
Component Orientation: Arrange parts with the pin 1 side closest to the tape's round sprocket holes on the
tape's trailing edge.
21 Marking Instructions
SO16NB package
Bar marked part way across Pin 1 end of package.
Bar width 10 to 20 mils, length to be at least four
times Bar width. Bar placement may extend across
chamfer and dimple areas.
MCBS374CA
AWLYWW
Pin 1 Dot or Dimple
1st line:
MCBS374CA (Part number coded on 10 digits)
2nd line:
Assembly site code AW (2 digits) followed by the
wafer lot code L (1 digit),
year Y (1 digit) and
work week WW (2 digits)
•
•
SO16NB Lead free package
Bar marked part way across Pin 1 end of package.
Bar width 10 to 20 mils, length to be at least four
times Bar width. Bar placement may extend across
chamfer and dimple areas.
MBS374CAEF
AWLYWW
Pin 1 Dot or Dimple
•
•
MOTOROLA
1st line:
MBS374CAEF (Part number coded on 10 digits)
2nd line:
Assembly site code AW (2 digits) followed by the
wafer lot code L (1 digit),
year Y (1 digit) and
work week WW (2 digits)
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
31
Freescale Semiconductor, Inc.
Case Outline
Freescale Semiconductor, Inc...
22 Case Outline
Millimeters
Note:
1994.
1. Dimensions and Tolerances per ASME Y14.5M,
Max
Note:
2. Controlling dimension: Millimeters.
Note: 3. Dimension D and E1 do not include mold
protrusion.
Inches
Dim
Min
Max
Min
A
1.35
1.75
0.054
0.068
A1
0.1
0.25
0.004
0.009
D
9.8
10
0.385
0.393
E
5.8
6.2
0.229
0.244
E1
3.8
4
0.150
0.157
b
0.35
0.49
0.014
0.019
c
0.19
0.25
0.008
0.009
e
1.27 BSC
Note:
4. Maximum mold protrusion 0.15 ( 0.006 ) per side.
Note: 5. Dimension b does not include Dambar protrusion.
Allowable Dambar protrusion shall be 0.127 ( 0.005 )
total in excess of the b dimension at maximum material
condition.
0.050 BSC
L
0.4
1.25
0.016
0.049
h
0.25
0.5
0.010
0.019
Q
0o
7o
0o
7o
Figure 17. SO16NB Package
32
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
HOW TO REACH US:
Information in this document is provided solely to enable system and software implementers to
use Motorola products. There are no express or implied copyright licenses granted hereunder to
USA/EUROPE/LOCATIONS NOT LISTED:
design or fabricate any integrated circuits or integrated circuits based on the information in this
Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217
1-303-675-2140 or 1-800-441-2447
document.
JAPAN:
for any particular purpose, nor does Motorola assume any liability arising out of the application or
Motorola reserves the right to make changes without further notice to any products herein.
Motorola makes no warranty, representation or guarantee regarding the suitability of its products
use of any product or circuit, and specifically disclaims any and all liability, including without
Motorola Japan Ltd.; SPS, Technical Information Center,
3-20-1, Minami-Azabu Minato-ku, Tokyo 106-8573 Japan
81-3-3440-3569
limitation consequential or incidental damages. “Typical” parameters which may be provided in
Motorola data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated
ASIA/PACIFIC:
for each customer application by customer’s technical experts. Motorola does not convey any
Motorola Semiconductors H.K. Ltd.; Silicon Harbour
Centre, 2 Dai King Street, Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
852-26668334
TECHNICAL INFORMATION CENTER:
license under its patent rights nor the rights of others. Motorola products are not designed,
intended, or authorized for use as components in systems intended for surgical implant into the
body, or other applications intended to support or sustain life, or for any other application in which
the failure of the Motorola product could create a situation where personal injury or death may
occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized
application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries,
1-800-521-6274
HOME PAGE:
http://www.motorola.com/semiconductors
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola
was negligent regarding the design or manufacture of the part.
Motorola and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. All other
product or service names are the property of their respective owners. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
© Motorola, Inc. 2003
MC44BS374CA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Case Outline
34
MC44BS374CA Technical data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA