DUAL 4-INPUT MULTIPLEXER WITH 3-STATE OUTPUTS The MC74AC353/74ACT353 is a dual 4-input multiplexer with 3-state outputs. It can select two bits of data from four sources using common Select inputs. The outputs may be individually switched to a high impedance state with a HIGH on the respective Output Enable (OE) inputs, allowing the outputs to interface directly with bus-oriented systems. • • • • • Inverted Version of the MC74AC253/74ACT253 Multifunction Capability Separate Enables for Each Multiplexer Outputs Source/Sink 24 mA ′ACT353 Has TTL Compatible Inputs VCC 16 OEb 15 S0 14 I3b 13 I2b 12 I1b 11 I0b 10 N SUFFIX CASE 648-08 PLASTIC Zb 9 PIN NAMES 1 2 3 4 5 6 7 8 OEa S1 I3a I2a I1a I0a Za GND I0a–I3a I0b–I3b S0, S1 OEa OEb Za, Zb Side A Data Inputs Side B Data Inputs Common Select Inputs Side A Enable Input Side B Enable Input Multiplexer Outputs D SUFFIX CASE 751B-05 PLASTIC TRUTH TABLE Select Inputs Data Inputs Output Enable Outputs S0 S1 I0 I1 I2 I3 OE Z X L L H H L L H H X L L L L H H H H X L H X X X X X X X X X L H X X X X X X X X X L H X X X X X X X X X L H H L L L L L L L L Z H L H L H L H L LOGIC SYMBOL S0 S1 OEa I0a I1a I2a I3a I0b I1b I2b I3b OEb Za Address inputs S0 and S1 are common to both sections. H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance FACT DATA 5-1 Zb MC74AC353 MC74ACT353 FUNCTIONAL DESCRIPTION The MC74AC353/74ACT353 contains two identical 4-input multiplexers with 3-state outputs. They select two bits from four sources selected by common Select inputs (S0, S1). The 4-input multiplexers have individual Output Enable (OEa, OEb) inputs which, when HIGH, force the outputs to a high impedance (High Z) state. The logic equations for the outputs are shown below: If the outputs of 3-state devices are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure that Output Enable signals to 3-state devices whose outputs are tied together are designed so that there is no overlap. Za = OEa•(I0a•S1•S0+I1a•S1•S0+ I2a•S1•S0+I3a•S1•S0) Zb = OEb•(I0b•S1•S0+I1b•S1•S0+ I2b•S1•S0+I3b•S1•S0) LOGIC DIAGRAM OEb I3b I2b I1b I0b S0 S1 Zb I3a I2a I1a Za Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. FACT DATA 5-2 I0a OEa MC74AC353 MC74ACT353 MAXIMUM RATINGS* Symbol Parameter Value Unit –0.5 to +7.0 V V VCC DC Supply Voltage (Referenced to GND) Vin DC Input Voltage (Referenced to GND) –0.5 to VCC +0.5 Vout DC Output Voltage (Referenced to GND) –0.5 to VCC +0.5 V Iin DC Input Current, per Pin ±20 mA Iout DC Output Sink/Source Current, per Pin ±50 mA ICC DC VCC or GND Current per Output Pin ±50 mA Tstg Storage Temperature –65 to +150 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage Vin, Vout DC Input Voltage, Output Voltage (Ref. to GND) tr, tf Input Rise and Fall Time (Note 1) ′AC Devices except Schmitt Inputs tr, tf Input Rise and Fall Time (Note 2) ′ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH IOL Min Typ Max ′AC 2.0 5.0 6.0 ′ACT 4.5 5.0 5.5 0 VCC VCC @ 3.0 V 150 VCC @ 4.5 V 40 VCC @ 5.5 V 25 VCC @ 4.5 V 10 VCC @ 5.5 V 8.0 Unit V V ns/V ns/V 140 °C 85 °C Output Current — High –24 mA Output Current — Low 24 mA –40 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. FACT DATA 5-3 25 MC74AC353 MC74ACT353 DC CHARACTERISTICS Symbol Parameter VCC (V) 74AC 74AC TA = +25°C TA = –40°C to +85°C Typ VIH VIL VOH Conditions Guaranteed Limits Minimum High Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC – 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC – 0.1 V Minimum High Level Output Voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 V 2.56 3.86 4.86 2.46 3.76 4.76 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 0.36 0.36 0.36 0.44 0.44 0.44 3.0 4.5 5.5 VOL Unit Maximum Low Level Output Voltage 3.0 4.5 5.5 0.002 0.001 0.001 IOUT = –50 µA V *VIN = VIL or VIH –12 mA IOH –24 mA –24 mA IOUT = 50 µA V V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA IIN Maximum Input Leakage Current 5.5 ±0.1 ±1.0 µA VI = VCC, GND IOZ Maximum 3-State Current 5.5 ±0.5 ±5.0 µA VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND 5.5 75 mA VOLD = 1.65 V Max 5.5 –75 mA VOHD = 3.85 V Min 80 µA VIN = VCC or GND IOLD IOHD ICC †Minimum Dynamic Output Current Maximum Quiescent Supply Current 5.5 8.0 * All outputs loaded; thresholds on input associated with output under test. † Maximum test duration 2.0 ms, one output loaded at a time. Note: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC. FACT DATA 5-4 MC74AC353 MC74ACT353 AC CHARACTERISTICS (For Figures and Waveforms — See Section 3) Symbol Parameter VCC* (V) Min 74AC 74AC TA = +25°C CL = 50 pF TA = –40°C to +85°C CL = 50 pF Typ Max Min Max Unit Fig. No. tPLH Propagation Delay Sn to Zn 3.3 5.0 3.0 3.0 15.5 11.0 2.0 2.0 17.5 12.5 ns 3-6 tPHL Propagation Delay Sn to Zn 3.3 5.0 3.0 3.0 16.0 11.5 2.0 2.0 18.0 13.0 ns 3-6 tPLH Propagation Delay In to Zn 3.3 5.0 2.0 2.0 14.5 10.0 1.0 1.0 17.0 11.5 ns 3-6 tPHL Propagation Delay In to Zn 3.3 5.0 2.0 2.0 13.0 9.5 1.0 1.0 15.0 11.0 ns 3-6 tPZH Output Enable Time 3.3 5.0 1.0 1.0 8.0 6.0 0.5 0.5 8.5 6.5 ns 3-7 tPZL Output Enable Time 3.3 5.0 1.0 1.0 8.0 6.0 0.5 0.5 9.0 7.0 ns 3-8 tPHZ Output Disable Time 3.3 5.0 2.0 2.0 9.5 8.0 1.0 1.0 10.0 8.5 ns 3-7 tPLZ Output Disable Time 3.3 5.0 2.0 2.0 8.0 7.0 1.0 1.0 9.0 7.5 ns 3-8 * Voltage Range 3.3 V is 3.3 V ±0.3 V. Voltage Range 5.0 V is 5.0 V ±0.5 V. FACT DATA 5-5 MC74AC353 MC74ACT353 DC CHARACTERISTICS Symbol Parameter VCC (V) 74ACT 74ACT TA = +25°C TA = –40°C to +85°C Typ Guaranteed Limits Unit Conditions VIH Minimum High Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC – 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC – 0.1 V VOH Minimum High Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V 3.86 4.86 3.76 4.76 0.1 0.1 0.1 0.1 4.5 5.5 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOL 24 mA ±0.1 ±1.0 µA VI = VCC, GND 1.5 mA VI = VCC – 2.1 V ±5.0 µA VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND 5.5 75 mA VOLD = 1.65 V Max 5.5 –75 mA VOHD = 3.85 V Min 80 µA VIN = VCC or GND 4.5 5.5 VOL Maximum Low Level Output Voltage 4.5 5.5 IIN Maximum Input Leakage Current 5.5 ∆ICCT Additional Max. ICC/Input 5.5 IOZ Maximum 3-State Current 5.5 IOLD IOHD ICC †Minimum Dynamic Output Current Maximum Quiescent Supply Current 0.001 0.001 0.6 ±0.5 5.5 8.0 * All outputs loaded; thresholds on input associated with output under test. † Maximum test duration 2.0 ms, one output loaded at a time. FACT DATA 5-6 V V IOUT = –50 µA *VIN = VIL or VIH –24 mA IOH –24 mA IOUT = 50 µA MC74AC353 MC74ACT353 AC CHARACTERISTICS (For Figures and Waveforms — See Section 3) Symbol Parameter VCC* (V) 74ACT 74ACT TA = +25°C CL = 50 pF TA = –40°C to +85°C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay Sn to Zn 5.0 3.0 10.0 2.5 11.5 ns 3-6 tPHL Propagation Delay Sn to Zn 5.0 3.0 10.0 2.5 11.5 ns 3-6 tPLH Propagation Delay In to Zn 5.0 2.0 10.0 1.5 11.0 ns 3-6 tPHL Propagation Delay In to Zn 5.0 2.0 8.0 1.5 9.0 ns 3-6 tPZH Output Enable Time, OEn to Zn 5.0 1.0 7.0 1.0 8.0 ns 3-7 tPZL Output Enable Time 5.0 1.0 7.5 1.0 8.0 ns 3-8 tPHZ Output Disable Time 5.0 1.0 9.0 1.0 10 ns 3-7 tPLZ Output Disable Time 5.0 1.0 7.0 1.0 9.0 ns 3-8 * Voltage Range 5.0 V is 5.0 V ±0.5 V. CAPACITANCE Symbol Parameter Value Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 50 pF VCC = 5.0 V FACT DATA 5-7 MC74AC353 MC74ACT353 OUTLINE DIMENSIONS N SUFFIX PLASTIC DIP PACKAGE CASE 648–08 ISSUE R –A– 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B F C DIM A B C D F G H J K L M S L S SEATING PLANE –T– K H G D M J 16 PL 0.25 (0.010) T A M M D SUFFIX PLASTIC SOIC PACKAGE CASE 751B–05 ISSUE J –A– 16 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C –T– SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 –B– INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] –TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ FACT DATA 5-8 *MC74AC353/D* MC74AC353/D