Order this document by LM323/D The LM323,A are monolithic integrated circuits which supply a fixed positive 5.0 V output with a load driving capability in excess of 3.0 A. These three–terminal regulators employ internal current limiting, thermal shutdown, and safe–area compensation. The A–suffix is an improved device with superior electrical characteristics and a 2% output voltage tolerance. These regulators are offered with a 0° to +125°C temperature range in a low cost plastic power package. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. These devices can be used with a series pass transistor to supply up to 15 A at 5.0 V. • Output Current in Excess of 3.0 A • • • • • • Available with 2% Output Voltage Tolerance No External Components Required 3–AMPERE, 5 VOLT POSITIVE VOLTAGE REGULATORS SEMICONDUCTOR TECHNICAL DATA T SUFFIX PLASTIC PACKAGE CASE 221A Internal Thermal Overload Protection Internal Short Circuit Current Limiting Pin 1. Input 2. Ground 3. Output Output Transistor Safe–Area Compensation Thermal Regulation and Ripple Rejection Have Specified Limits 1 2 3 Heatsink surface is connected to Pin 2. Simplified Application Input LM323, A Cin* 0.33µF Output CO** A common ground is required between the input and the output voltages. The input voltage must remain typically 2.5 V above the output voltage even during the low point on the input ripple voltage. * Cin is required if regulator is located an appreciable * distance from power supply filter. (See Applications * Information for details.) ** CO is not needed for stability; however, it does ** improve transient response. ORDERING INFORMATION Device Output Voltage Tolerance LM323T 4% LM323AT 2% Motorola, Inc. 1996 MOTOROLA ANALOG IC DEVICE DATA Operating Temperature Range Package TJ = 0° to +125°C Plastic Power Rev 0 1 LM323, A MAXIMUM RATINGS Symbol Value Unit Input Voltage Rating Vin 20 Vdc Power Dissipation PD Internally Limited W Operating Junction Temperature Range TJ 0 to +125 °C Tstg –65 to +150 °C Tsolder 300 °C Storage Temperature Range Lead Temperature (Soldering, 10 s) ELECTRICAL CHARACTERISTICS (TJ = Tlow to Thigh [Note 1], unless otherwise noted.) LM323A Characteristics LM323 Symbol Min Typ Max Min Typ Max Unit Output Voltage (Vin = 7.5 V, 0 ≤ Iout ≤ 3.0 A, TJ = 25°C) VO 4.9 5.0 5.1 4.8 5.0 5.2 V Output Voltage (7.5 V ≤ Vin ≤ 15 V, 0 ≤ Iout ≤ 3.0 A, P ≤ Pmax) (Note 2) VO 4.8 5.0 5.2 4.75 5.0 5.25 V Line Regulation (7.5 V ≤ Vin ≤ 15 V, TJ = 25°C) (Note 3) Regline – 1.0 15 – 1.0 25 mV Load Regulation (Vin = 7.5 V, 0 ≤ Iout ≤ 3.0 A, TJ = 25°C) (Note 3) Regload – 10 50 – 10 100 mV Regtherm – 0.001 0.01 – 0.002 0.03 %VO/W Quiescent Current (7.5 V ≤ Vin ≤ 15 V, 0 ≤ Iout ≤ 3.0 A) IB – 3.5 10 – 3.5 20 mA Output Noise Voltage (10 Hz ≤ f ≤ 100 kHz, TJ = 25°C) VN – 40 – – 40 – µVrms Ripple Rejection (8.0 V ≤ Vin ≤ 18 V, Iout = 2.0A, f = 120 Hz, TJ = 25°C) RR 66 75 – 62 75 – dB Short Circuit Current Limit (Vin = 15 V, TJ = 25°C) (Vin = 7.5 V, TJ = 25°C) ISC – – 4.5 5.5 – – – – 4.5 5.5 – – S – – 35 – – 35 mV RΘJC – 2.0 – – 2.0 – °C/W Thermal Regulation (Pulse = 10 ms, P = 20 W, TA = 25°C) Long Term Stability Thermal Resistance, Junction–to–Case (Note 4) A NOTES: 1. Tlow to Thigh = 0° to +125°C 2. Although power dissipation is internally limited, specifications apply only for P ≤ Pmax = 25 W. 3. Load and line regulation are specified at constant junction temperature. Pulse testing is required with a pulse width ≤ 1.0 ms and a duty cycle ≤ 5%. 4. Without a heatsink, the thermal resistance (RθJA is 65°C/W). With a heatsink, the effective thermal resistance can approach the specified values of 2.0°C/W, depending on the efficiency of the heatsink. 2 MOTOROLA ANALOG IC DEVICE DATA LM323, A Representative Schematic Diagram 2 1.0k Input 1.0k 210 Q2 Q1 Q8 Q22 6.7V Q20 Q9 Q21 16k 100 Q24 1.0k Q25 200 Q27 300 Q3 Q4 3.0k 10k Q26 10pF Q19 5.6k Q5 300 Q23 13 Q16 Q10 520 50 0.12 200 Output Q12 2.6k 2.0k 3.9k Q6 Q7 40pF 6.0k Q17 Q13 840 7.2k Q18 1.7k Q15 Q11 6.0k Q14 2.8k Gnd VOLTAGE REGULATOR PERFORMANCE 2 2 1 18 V Iout , OUTPUT CURRENT (A) Vin , INPUT VOLTAGE (V) ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) (2.0 mV/DIV) Figure 1. Line and Thermal Regulation ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) (2.0 mV/DIV) be caused by a change in either input voltage or the load current. Thermal regulation is a function of IC layout and die attach techniques, and usually occurs within 10 ms of a change in power dissipation. After 10 ms, additional changes in the output voltage are due to the temperature coefficient of the device. Figure 1 shows the line and thermal regulation response of a typical LM323A to a 20 W input pulse. The variation of the output voltage due to line regulation is labeled À and the thermal regulation component is labeled Á. Figure 2 shows the load and thermal regulation response of a typical LM323A to a 20 W load pulse. The output voltage variation due to load regulation is labeled À and the thermal regulation component is labeled Á. The performance of a voltage regulator is specified by its immunity to changes in load, input voltage, power dissipation, and temperature. Line and load regulation are tested with a pulse of short duration (< 100 µs) and are strictly a function of electrical gain. However, pulse widths of longer duration (> 1.0 ms) are sufficient to affect temperature gradients across the die. These temperature gradients can cause a change in the output voltage, in addition to changes by line and load regulation. Longer pulse widths and thermal gradients make it desirable to specify thermal regulation. Thermal regulation is defined as the change in output voltage caused by a change in dissipated power for a specified time, and is expressed as a percentage output voltage change per watt. The change in dissipated power can 8.0 V t, TIME (2.0 ms/DIV) Vout = 5.0 V Vin = 8.0 V → 18 V → 8.0 V Iout = 2.0 A 1 = Regline = 2.4 mV 2 = Regtherm = 0.0015% VO/W MOTOROLA ANALOG IC DEVICE DATA Figure 2. Load and Thermal Regulation 2 1 2 2.0 0 t, TIME (2.0 ms/DIV) Vout = 5.0 V Vin = 15 V Iout = 0 A → 2.0 A → 0 A 1 = Regline = 5.4 mV 2 = Regtherm = 0.0015% VO/W 3 LM323, A Figure 3. Temperature Stability Figure 4. Output Impedance 10 Z O , OUTPUT IMPEDANCE ( Ω ) Vout , OUTPUT VOLTAGE (Vdc) 5.1 Vin = 10 V Iout = 100 mA 5.0 4.9 –90 –50 –10 30 70 110 TJ, JUNCTION TEMPERATURE (°C) 150 190 10–1 10–2 10–3 10–4 1.0 Figure 5. Ripple Rejection versus Frequency 10 100 1.0 k 10 k 100 k f, FREQUENCY (Hz) 1.0 M 10 M 100 M Figure 6. Ripple Rejection versus Output Current 100 100 Iout = 50 mA RR, RIPPLE REJECTION (dB) RR, RIPPLE REJECTION (dB) Vin = 7.5 V Iout = 1.0 A CO = 0 TJ = 25°C 80 Iout = 3.0 A 60 Vin = 10 V CO = 0 TJ = 25°C 40 80 60 Vin = 10 V CO = 0 f = 120 Hz TJ = 25°C 40 20 1.0 10 100 1.0 k 10 k 100 k f, FREQUENCY (Hz) 1.0 M 10 M 30 0.01 100 M Figure 7. Quiescent Current versus Input Voltage 5.0 TJ = 55°C TJ = 25°C 3.0 TJ = 150°C 2.0 TJ = 150°C Iout = 2.0 A TJ = 55°C 1.0 10 Figure 8. Quiescent Current versus Output Current IB , QUIESCENT CURRENT (mA) IB , QUIESCENT CURRENT (mA) 4.0 0.1 1.0 Iout, OUTPUT CURRENT (A) 4.0 TJ = –55°C TJ = 25°C 3.0 2.0 TJ = 150°C 1.0 Vin = 10 V TJ = 25°C 0 4 0 5.0 10 15 Vin, INPUT VOLTAGE (Vdc) 20 0 0.01 0.1 1.0 Iout, OUTPUT CURRENT (A) 10 MOTOROLA ANALOG IC DEVICE DATA LM323, A Figure 9. Dropout Voltage Figure 10. Short Circuit Current Iout = 3.0 A 2.0 Iout = 1.0 A 1.5 Iout = 0.5 A 1.0 ∆Vout = 50 mV –50 –10 30 70 110 TJ, JUNCTION TEMPERATURE (°C) 150 6.0 TJ = 0°C TJ = 25°C 4.0 TJ = 125°C 2.0 0 5.0 190 10 Figure 11. Line Transient Response 0.8 Iout = 150 mA CO = 0 TJ = 25°C 0.6 0.4 0.2 0 –0.2 –0.4 –0.6 1.0 0.5 0 0 10 20 30 15 Vin, INPUT VOLTAGE (Vdc) 20 25 Figure 12. Load Transient Response ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) 0.5 –90 ∆ Vin , INPUT VOLTAGE CHANGE (V) ISC , SHORT CIRCUIT CURRENT AT ZERO VOLTS (A) 8.0 Iout , OUTPUT CURRENT (A) V in –Vout , INPUT TO OUTPUT VOLTAGE DIFFERENTIAL (Vdc) 2.5 40 0.3 Vin = 10 V CO = 0 TJ = 25°C 0.2 0.1 0 –0.1 –0.2 –0.3 1.5 1.0 0.5 0 0 10 20 30 40 t, TIME (µs) t, TIME (µs) APPLICATIONS INFORMATION Design Considerations The LM323,A series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjected to an excessive power overload condition, Internal Short Circuit Protection that limits the maximum current the circuit will pass, and Output Transistor Safe–Area Compensation that reduces the output short circuit current as the voltage across the pass transistor is increased. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the MOTOROLA ANALOG IC DEVICE DATA regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. An input bypass capacitor should be selected to provide good high–frequency characteristics to insure stable operation under all load conditions. A 0.33 µF or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulator’s input terminals. Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. 5 LM323, A Figure 13. Current Regulator Figure 14. Adjustable Output Regulator LM323, A Input Output LM323, A R 0.33µF IO Input Constant Current to Grounded Load 7 – 0.33µF The LM323,A regulator can also be used as a current source when connected as above. Resistor R determines the current as follows: 6 MC1741 + 1.0k 2 0.1µF 3 10k 4 IO = 5.0 V + IB R ∆IB IB ^ 0.7 mA over line, load and temperature changes ^ 3.5 mA VO, 8.0 V to 20 V For example, a 2.0 A current source would require R to be a 2.5 Ω, 15 W resistor and the output voltage compliance would be the input voltage less 7.5 V. The addition of an operational amplifier allows adjustment to higher or intermediate values while retaining regulation characteristics. The minimum voltage obtainable with this arrangement is 3.0 V greater than the regulator voltage. Figure 16. Current Boost with Short Circuit Protection Figure 15. Current Boost Regulator 2N4398 or Equiv R Input LM323, A Rsc 2N4398 or Equiv. MJ2955 or Equiv. Output R 1.0µF Vin – VO ≥ 2.5 V LM323, A Output 0.1µF 1.0µF The LM323, A series can be current boosted with a PNP transistor. The 2N4398 provides current to 15 A. Resistor R in conjuction with the VBE of the PNP determines when the pass transistor begins conducting; this circuit is not short circuit proof. Input–output differential voltage minimum is increased by the VBE of the pass transistor. 6 The circuit of Figure 16 can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, RSC, and an additional PNP transistor. The current sensing PNP must be able to handle the short circuit current of the three–terminal regulator. Therefore, an 8.0 A power transistor is specified. MOTOROLA ANALOG IC DEVICE DATA LM323, A OUTLINE DIMENSIONS T SUFFIX PLASTIC PACKAGE CASE 221A–06 ISSUE Y –T– B C F T S SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. 4 A Q 1 2 3 U H K Z L R V J G D N MOTOROLA ANALOG IC DEVICE DATA DIM A B C D F G H J K L N Q R S T U V Z INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 ––– ––– 0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 ––– ––– 2.04 7 LM323, A Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 8 ◊ *LM323/D* MOTOROLA ANALOG IC DEVICE DATA LM323/D