DATA SHEET GBJ4A~GBJ4K GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 4.0 Amperes Recongnized File #E228882 GBJ Unit: inch ( mm ) FEATURES 0.122(3.1) 0.142(3.6) 0.146(3.7) 0.129(3.3) • Surge overload rating: 150 Amperes peak 0.578(14.7) 0.603(15.3) • Reliable low cost construction utilizing molded plastic technique • High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension 0.087(2.2) 0.070(1.8) Case: Reliable low cost construction utilizing molded plastic technique 0.044(1.1) 0.035(0.9) Terminals: Leads solderable per MIL-STD-202, Method 208 0.304(7.7) 0.288(7.3) Mounting position: Any 0.115(2.9) 0.098(2.5) 0.669(17.0) 0.709(18.0) MECHANICAL DATA 0.304(7.7) 0.288(7.3) 0.304(7.7) 0.288(7.3) Mounting torque: 5 in. lb. Max. 0.150(3.8) 0.133(3.4) 0.382(9.7) 0.366(9.3) • Ideal for printed circuit board 0.189(4.8) 0.173(4.4) 0.996(25.3) 0.972(24.7) C 0.118 (3.0) • Plastic material has Underwriters Laboratory Flammability Classification 94V-O 0.032(0.8) 0.024(0.6) Weight: 0.15 ounce, 4.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. GBJ4J GBJ4K UNIT 400 600 800 V 140 280 420 560 V 200 400 600 800 V GBJ4A GBJ4B GBJ4D Maximum Recurrent Peak Reverse Voltage 50 100 200 Maximum RMS Input Voltage 35 70 Maximum DC Blocking Voltage 50 100 Maximum Average Forward TC=100°C GBJ4G 4.0 A I2t Rating for fusing ( t<8.3ms) 127 A2sec Peak Forward Surge Current single sine-wave superimposed on rated load (JEDEC method) 150 Apk Maximum Instantaneous Forward Voltage Drop per element at 2.0A 1.0 Vpk Maximum Reverse Leakage at rated TA=25° 5 CDc Blocking Voltage per element TC=100°C 500 µA µA Typical Thermal Resistance per leg(Note 2) RθJA 8.6 °C / W Typical Thermal Resistance per leg(Note 3) RθJC 3.1 °C / W -55 to +150 °C Rectified Output Current Operating and Storage Temperature Range, TJ,TSTG NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate. DATE : OCT.08.2002 PAGE . 1 INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD CURRENT AMPERES RATING AND CHARACTERISTIC C URVES 6.0 HEAT-SINK MOUNTING,TC (4* 4 * 0 .15) INCH COPPER PLATE 4.0 2.0 MOUNTED ON PC BOARD. TA 0.5"(12.7mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 50 100 150 100 40 20 10 4.0 TJ= 25OC Pulse Wid th= 300 S 1% DULY Cyc le 2.0 1.0 0.4 0.2 0.1 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 Fig . 2- TYPICAL INSTANTANEOUS FORWARD CHARACTERIS ITCS PER ELEMENT FPRWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS FORWARD VOLT AGE, V OLTS Fig . 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT INSTANTANEOUS REVERSE CURRENT, MICROAMPERES TEMPERATUREOC 10 O TC = 100 C 1.0 0.1 O TA= 25 C 0.01 0 20 40 60 80 100 120 140 PERCENT OF PEAK REVERSE VOLTAGE 150 120 90 60 O TA= 105 C 30 0 1 2 6 10 20 40 60 100 NO. OF CYCLES AT 62Hz Fig . 3- TYP ICAL REAK REVERSE CHARACTERISTICS Fig . 4- MAXIMUM NON-REPETITEVE PEAK FORWARD S URGE CURRENT CAPACITANCE, p F 400 100 O Tj= 25 C f= 1.0MHz Vsig = 50mVp -p 50 10 1 5 10 50 100 REVERSE VOLTAGE, VOLTS Fig.5- TYPICL JUNCTION CAPACITANCE PERELEMENT DATE : OCT.08.2002 PAGE . 2