Features ● ● ● ● ● ● ● ● ● ● INNOLINE Single Output up to 25A Dual Outputs Total Power up to 100W Input/Output 1.6kVDC Isolation Adjustable Output Voltage Under-Voltage Lockout No Minimum Load Industry Standard Footprint Fixed Operating Frequency Halt Tested Compact 61.0 x 57.91 x 12.7mm Package High Efficiency to 90% DC/DC-Converter RP100-S_DI Series Selection Guide Part Number Single Output Input Voltage (VDC) Output Voltage (VDC) Output Current (A) RP100-481.8S 36 – 75 1.8 25 4 RP100-482.5S 36 – 75 2.5 25 5 8 1.608 87 RP100-483.3S 36 – 75 3.3 25 7 10 2.022 90 RP100-4805S 36 – 75 5 20 10 15 2.480 90 RP100-4815S 36 – 75 15 6.66 30 45 2.507 90 Output Current I1 / I2 (A) Line Regulation V1 / V2 (mV) Load Regulation V1 / V2 (mV) Part Number Input Efficiency (9) Current(8) (A) % 6 1.157 86 (VDC) Output Voltage V1 / V2 (VDC) (A) % RP100-483.305DI 36 – 75 5 / 3.3 20 / 25 25 / 16.5 25 / 16.5 2.39 87 RP100-482.505DI 36 – 75 5 / 2.5 20 / 25 25 / 12.5 25 / 12.5 2.45 85 RP100-482.53.3DI 36 – 75 3.3 / 2.5 25 / 25 16.5 / 12.5 16.5 / 12.5 2.44 85 Dual Output Input Voltage Line Load Regulation Regulation (mV) (mV) 100 Watt Isolated Single & Dual Output Input Efficiency Current(8) (9) Notes: 1. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used, the +Vsense should be connected to its corresponding +Vout and likewise the -Vsense should be connected to its corresponding -Vout. 2. Single: Measured with a 1uF M/C and a 10uF T/C. Dual: For each outputs. 3. An external filter capacitor is required for normal operation. The capacitor should be capable of handing 1A ripple current for 48V models. RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90mΩ. 4. Single: The negative / positive logic and length are optional ( see table ). The pin voltage is referenced to negative input. Dual: The ON/OFF control function. There are positive logic ( standard ) and negative logic ( option ). The pin voltage is referenced to negative input. To order negative logic ON/OFF control add the suffix-N. ( Ex:RP100-483.305I/N ) 5. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40°C. ( Ground fixed and controlled environment ) 6. Heat sink is optional and P/N: 7G-0021, 7G-0022, 7G-0023, 7G-0024. 7. The RP100 meets level A and level B conducted emissions only with external components connected before the input pin to the converter. 8. Maximum value at nominal input voltage and full load. 9. Typical value at nominal input voltage and full load. The dual efficiency test condition: RP100-483.305DI @ 5V/12A and 3.3V/12A RP100-482.505DI @ 5V/12A and 2.5V/16A RP100-482.53.3DI @ 3.3V/18A and 2.5V/16A 10. BASEPLATE GROUNDING: Base-plate should be grounded at one of four screw bolts prior to operation. 11. The converter is provided by basic insulation. N” for Negative remote ON/OFF. 12. “N 13. “PP” for Positive remote ON/OFF. www.recom-international.com April-2005 149 INNOLINE RP100-S_DI Series DC/DC-Converter Specifications (refer to the standard application circuit, Ta: 25°C) Input Voltage Range 36-75VDC 48V nom. Over-Voltage Lockout Start-up Voltage Dual 76.5V typ. Over-Voltage Lockout Shuntdown Voltage Unde-Voltage Lockout Start-up Voltage Dual Single Dual Single Dual 78.5V typ. 34V typ. 35V typ. 32V typ. 33V typ. Unde-Voltage Lockout Shuntdown Voltage Input Filter (Note 3) Input voltage variation dv/dt Input Surge Voltage 100mS max Single Start up time Nominal Vin and constant resistive load Single Input Reflected-Ripple Current Single (5Hz to 20Hz, 12uH Source inpedance) Remote ON/OFF (Note 4) Single (Positive logic) Single (Negative logic) Dual (Positive logic) Dual (Negative logic) Continuous Output Power Output Voltage Accuracy (Full load and nominal Vin) Output Voltage Adjustment (Note 1) L-C type 5V/ms max (Complies with ETS300 132 part4.4) 100VDC 20mAp-p ON=Open or 3.5V < Vr < 15V, OFF=Short or 0V < Vr < 1.2V, ON=Short or 0V < Vr < 1.2V, OFF=Open or 3.5V < Vr < 15V, ON=Open or 3.5V < Vr < +Vin, OFF=Short or Vr < 1.2V, ON=Short or 3.5V < Vr < +Vin, OFF=Open or Vr < 1.2V. IIN=50µA max. IIN=1mA max. IIN=1mA max. IIN=50µA max. 100W max. ±1.5% ±1.0% +10%, -20% ±10% Single Dual Single Dual Minimum Load Line Regulation Load Regulation 25mS typ. 0% LL to HL at FL Single 0% to 100% FL Dual 0% to 100% FL Dual for each Outputs Remote Sense (Note 1) See table See table 10% of Vout Ripple and Noise 20MHz bandwidth (Note 2) 100mVp-p Temperature Coefficient ±0.02%/ºC Transient Response Recovery Time (25% load step change) Over Voltage Protection threshold (Hiccup) Single & Dual 2.5V 3.3V 5V Over Current Protection threshold 200us 115% ~ 130% of Vout 3.0V 3.9V 6.2V 110% ~ 140% of Iout Rated Short Circuit Protection Hiccup, Automatic recovery Efficiency (at nominal input voltage, full load) up to 90% Continued next page 150 April-2005 www.recom-international.com RP100-S_DI Series INNOLINE DC/DC-Converter Specifications (refer to the standard application circuit, Ta: 25°C) Isolation Voltage Isolation Resistance Isolation Capacitance Input to Output Input to Case Output to Case Single Dual Single Dual Operating Frequency Operating Base-plate Temperature Range ( Note 6 ) Over Temperature Protection 300KHz typ. Single Dual for Base-plate Storage Temperature Range 95% Thermal Shock MIL-STD-810D Vibration Conducted Emissions 10 ~ 55Hz 2G, 3minutes period, 30minutes analog EN55022 (Note 7) EN55022 (Note 7) Radiated Emisssions ESD Radiated Immunity Fast Transient Surge Conducted Immunity EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Case Material Dual www.recom-international.com X, Y and Z Level A Level B Level A Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Non-conductive black plastic Base material MTBF ( Note 6 ) -40ºC to +100ºC 110°C 105°C -55°C to +125°C Humidity max., Non-condensing Potting material Weight 1.600VDC min. 1.000VDC min. 1.000VDC min. 7 10 ohms min. 9 10 ohms min 2.500pF max. 1.500pF max. Aluminum base-plate Dual Single Dual Single Silicon (UL94-V0) 55g 105g 6 2 x 10 hrs 6 1.004 x 10 hrs April-2005 151 RP100-S_DI Series INNOLINE DC/DC-Converter Characteristics Efficiency vs Output Load 100 90 80 Efficiency (%) 70 60 50 10 20 30 40 50 60 70 80 90 100 Output Power (%) Ta=25°C 48V Input Without Heatsink 110 90 1.) LFM590 2.) LFM400 3.) LFM200 Output Power (%) 70 50 4.) LFM20 30 10 -40 -20 0 20 40 60 1 80 2 34 100 Ambient Temperature (°C) 48V Input With Heatsink (7G-0022) 110 90 1.) LFM590 2.) LFM400 3.) LFM200 Output Power (%) 70 50 4.) LFM20 30 10 -40 -20 0 20 40 60 1 80 2 34 100 Ambient Temperature (°C) 152 April-2005 www.recom-international.com INNOLINE RP100-S_DI Series DC/DC-Converter Package Style and Pinning (mm) 3rd angle projection Single Output 60.96 57.91 12.70 Side View 5.08 50.80 48.26 4xM3 x 0.5 ( Note 10) Pin Connections 5 1 2 35.56 6 Bottom View 15.24 25.40 7 3 8 4 9 17.78 10.16 External Output Trimming 7 6 8 Trim Down RD RU 7 Pin Ø 1.016 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm Product Options Table Output can be externally trimmed by using the method shown below. See application notes for values. Trim Up Pin # Function 1 –Vin 2 Case 3 Remote ON/OFF 4 +Vin 5 –Vout 6 –Vsense 7 Trim 8 +Vsense 9 +Vout XX.X ± 0.5 mm XX.XX ± 0.25 mm Pin pitch tolerance 0.35mm Option Suffix Negative remote ON/OFF logic, 0.20” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length L Negative remote ON/OFF logic, 0.11” pin length K Positive remote ON/OFF logic, 0.20” pin length P Positive remote ON/OFF logic, 0.145” pin length S Positive remote ON/OFF logic, 0.11” pin length M Example: RP100-483.3S/P www.recom-international.com April-2005 153 INNOLINE RP100-S_DI Series DC/DC-Converter Package Style and Pinning (mm) 3rd angle projection Dual Output 60.96 57.91 5.08 12.70 Side View 50.80 48.26 4xM3 x 0.5 ( Note 10) Pin Connections 5 1 6 35.56 2 Bottom View 7 25.40 10.16 15.24 40.64 8 3 9 4 Product Options Table Option Output can be externally trimmed by using the method shown below. See application notes for values. ( ) for V2 output trim 9(6) 10(7) 154 8(5) Suffix Negative remote ON/OFF logic, 0.20” pin length (standard) Trim Down RD RU 10(7) Pin Ø 1.016 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm 2.032 mm 1.016 mm 2.032 mm 2.032 mm 1.016 mm 10 External Output Trimming Trim Up Pin # Function 1 –Vin 2 Case 3 Remote ON/OFF 4 +Vin 5 +V2 6 –V2 (Com) 7 V2 Trim 8 +V1 9 +V1 (Com) 10 V1 Trim XX.X ± 0.5 mm XX.XX ± 0.25 mm Pin pitch tolerance 0.35mm Negative remote ON/OFF logic, 0.145” pin length L Negative remote ON/OFF logic, 0.11” pin length K Positive remote ON/OFF logic, 0.20” pin length P Positive remote ON/OFF logic, 0.145” pin length S Positive remote ON/OFF logic, 0.11” pin length M Example: RP100-483.305I/N April-2005 www.recom-international.com