K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Document Title 256Kx36 & 512Kx18-Bit Synchronous Burst SRAM Revision History Rev. No. History Draft Date Remark 0.0 Initial draft May. 18 . 2001 Preliminary 0.1 Add x32 org part and industrial temperature part Aug. 11. 2001 Preliminary 0.2 1. change scan order(1) form 4T to 6T at 119BGA(x18) Aug. 28. 2001 Preliminary 1.0 1. Final spec release 2. Change ISB2 form 50mA to 60mA Nov. 16. 2001 Final 2.0 Change ordering information( remove 225MHz at SPB) April. 01. 2002 Final 2.1 1. Delete 119BGA package April. 04. 2003 Final 3.0 1. Remove x32 organization 2. Remove -85 speed bin Nov. 17. 2003 Final The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions on the parameters of this device. If you have any questions, please contact the SAMSUNG branch office near your office, call or contact Headquarters. -1- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM 8Mb SB/SPB Synchronous SRAM Ordering Information Org. Part Number K7B801825B-QC(I)65/75 512Kx18 K7A801800B-QC(I)16/14 K7A801809B-QC(I)25 K7B803625B-QC(I)65/75 256Kx36 K7A803600B-QC(I)16/14 K7A803609B-QC(I)25 Mode VDD Speed FT ; Access Time(ns) Pipelined ; Cycle Time(MHz) SB 3.3 6.5/7.5 ns SPB(2E1D) 3.3 167/138 MHz SPB(2E1D) 3.3 250 MHz SB 3.3 6.5/7.5 ns SPB(2E1D) 3.3 167/138 MHz SPB(2E1D) 3.3 250 MHz -2- PKG Temp Q: 100TQFP C: Commercial Temperature Range I: Industrial Temperature Range Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM 256Kx36 & 512Kx18-Bit Synchronous Burst SRAM FEATURES GENERAL DESCRIPTION • Synchronous Operation. • On-Chip Address Counter. • Self-Timed Write Cycle. • On-Chip Address and Control Registers. • 3.3V+0.165V/-0.165V Power Supply. • I/O Supply Voltage 3.3V+0.165V/-0.165V for 3.3V I/O or 2.5V+0.4V/-0.125V for 2.5V I/O • 5V Tolerant Inputs Except I/O Pins. • Byte Writable Function. • Global Write Enable Controls a full bus-width write. • Power Down State via ZZ Signal. • LBO Pin allows a choice of either a interleaved burst or a linear burst. • Three Chip Enables for simple depth expansion with No Data Contention only for TQFP. • Asynchronous Output Enable Control. • ADSP, ADSC, ADV Burst Control Pins. • TTL-Level Three-State Output. • 100-TQFP-1420A • Operating in commeical and industrial temperature range. The K7B803625B and K7B801825B are 9,437,184-bit Synchronous Static Random Access Memory designed for high performance second level cache of Pentium and Power PC based System. It is organized as 256K(512K) words of 36(18) bits and integrates address and control registers, a 2-bit burst address counter and added some new functions for high performance cache RAM applications; GW, BW, LBO, ZZ. Write cycles are internally self-timed and synchronous. Full bus-width write is done by GW, and each byte write is performed by the combination of WEx and BW when GW is high. And with CS1 high, ADSP is blocked to control signals. Burst cycle can be initiated with either the address status processor(ADSP) or address status cache controller(ADSC) inputs. Subsequent burst addresses are generated internally in the system′s burst sequence and are controlled by the burst address advance(ADV) input. LBO pin is DC operated and determines burst sequence(linear or interleaved). ZZ pin controls Power Down State and reduces Stand-by current regardless of CLK. The K7B803625B and K7B801825B are fabricated using SAMSUNG′s high performance CMOS technology and is available in a 100pin TQFP and Multiple power and ground pins are utilized to minimize ground bounce. FAST ACCESS TIMES PARAMETER Symbol -65 -75 -85 Unit Cycle Time tCYC 7.5 8.5 10 ns Clock Access Time tCD 6.5 7.5 8.5 ns Output Enable Access Time tOE 3.5 3.5 4.0 ns LOGIC BLOCK DIAGRAM CLK LBO BURST CONTROL LOGIC CONTROL REGISTER ADV ADSC A0~A1 A0~A17 or A0~A18 ADSP ADDRESS REGISTER A′0~A′1 256Kx36 , 512Kx18 MEMORY ARRAY A2~A17 or A2~A18 DATA-IN REGISTER CONTROL REGISTER CS1 CS2 CS2 GW BW WEx (x=a,b,c,d or a,b) BURST ADDRESS COUNTER OUTPUT BUFFER CONTROL LOGIC OE ZZ DQa0 ~ DQd7 or DQa0 ~ DQb7 DQPa ~ DQPd DQPa,DQPb -3- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM CLK GW BW OE ADSC ADSP ADV A8 A9 88 87 86 85 84 83 82 81 WEa VSS WEb 93 89 WEc 94 90 WEd 95 CS2 CS2 96 VDD CS1 97 91 A7 98 92 A6 99 100 Pin TQFP (20mm x 14mm) 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A4 A3 A2 A1 A0 N.C. N.C. VSS VDD N.C. A17 A10 A11 A12 A13 A14 A15 A16 K7B803625B(256Kx36) A5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 LBO DQPc DQc0 DQc1 VDDQ VSSQ DQc2 DQc3 DQc4 DQc5 VSSQ VDDQ DQc6 DQc7 N.C. VDD N.C. VSS DQd0 DQd1 VDDQ VSSQ DQd2 DQd3 DQd4 DQd5 VSSQ VDDQ DQd6 DQd7 DQPd 100 PIN CONFIGURATION(TOP VIEW) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DQPb DQb7 DQb6 VDDQ VSSQ DQb5 DQb4 DQb3 DQb2 VSSQ VDDQ DQb1 DQb0 VSS N.C. VDD ZZ DQa7 DQa6 VDDQ VSSQ DQa5 DQa4 DQa3 DQa2 VSSQ VDDQ DQa1 DQa0 DQPa PIN SYMBOL PIN NAME TQFP PIN NO. 32,33,34,35,36,37,43 44,45,46,47,48,49,50 81,82,99,100 83 ADV Burst Address Advance Address Status Processor 84 ADSP Address Status Controller 85 ADSC 89 Clock CLK 98 Chip Select CS1 97 Chip Select CS2 92 Chip Select CS2 93,94,95,96 WEx(x=a,b,c,d) Byte Write Inputs 86 Output Enable OE 88 Global Write Enable GW 87 Byte Write Enable BW 64 Power Down Input ZZ 31 Burst Mode Control LBO A0 - A17 Address Inputs SYMBOL PIN NAME TQFP PIN NO. VDD VSS N.C. Power Supply(+3.3V) Ground No Connect 15,41,65,91 17,40,67,90 14,16,38,39,42,66 DQa0~a7 DQb0~b7 DQc0~c7 DQd0~d7 DQPa~Pd Data Inputs/Outputs 52,53,56,57,58,59,62,63 68,69,72,73,74,75,78,79 2,3,6,7,8,9,12,13 18,19,22,23,24,25,28,29 51,80,1,30 VDDQ Output Power Supply (2.5V or 3.3V) Output Ground 4,11,20,27,54,61,70,77 VSSQ 5,10,21,26,55,60,71,76 Notes : 1. A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired. 2. The pin 42 is reserved for address bit for the 16Mb . -4- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM ADSP ADV A8 A9 83 82 81 48 49 50 A15 A16 A17 ADSC 84 47 A14 OE 85 46 A13 BW 86 45 A12 GW 87 44 A11 CLK 88 43 A18 VSS 89 WEa 90 WEb 93 42 N.C. 94 N.C. N.C. 95 CS2 CS2 96 VDD CS1 97 91 A7 98 92 A6 99 100 Pin TQFP (20mm x 14mm) 31 32 33 34 35 36 37 38 39 40 41 A4 A3 A2 A1 A0 N.C. N.C. VSS VDD K7B801825B(512Kx18) A5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 LBO N.C. N.C. N.C. VDDQ VSSQ N.C. N.C. DQb0 DQb1 VSSQ VDDQ DQb2 DQb3 N.C. VDD N.C. VSS DQb4 DQb5 VDDQ VSSQ DQb6 DQb7 DQPb N.C. VSSQ VDDQ N.C. N.C. N.C. 100 PIN CONFIGURATION(TOP VIEW) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A10 N.C. N.C. VDDQ VSSQ N.C. DQPa DQa7 DQa6 VSSQ VDDQ DQa5 DQa4 VSS N.C. VDD ZZ DQa3 DQa2 VDDQ VSSQ DQa1 DQa0 N.C. N.C. VSSQ VDDQ N.C. N.C. N.C. PIN NAME SYMBOL PIN NAME A0 - A18 Address Inputs ADV ADSP ADSC CLK CS1 CS2 CS2 WEx OE GW BW ZZ LBO Burst Address Advance Address Status Processor Address Status Controller Clock Chip Select Chip Select Chip Select Byte Write Inputs Output Enable Global Write Enable Byte Write Enable Power Down Input Burst Mode Control TQFP PIN NO. SYMBOL 32,33,34,35,36,37,43 44,45,46,47,48,49,50 80,81,82,99,100 83 84 85 89 98 97 92 93,94 86 88 87 64 31 PIN NAME TQFP PIN NO. VDD VSS N.C. Power Supply(+3.3V) Ground No Connect 15,41,65,91 17,40,67,90 1,2,3,6,7,14,16,25,28,29, 30,38,39,42,51,52,53,56, 57,66,75,78,79,95,96 DQa0 ~ a7 DQb0 ~ b7 DQPa, Pb VDDQ Data Inputs/Outputs 58,59,62,63,68,69,72,73 8,9,12,13,18,19,22,23 74,24 4,11,20,27,54,61,70,77 VSSQ Output Power Supply (2.5V or 3.3V) Output Ground 5,10,21,26,55,60,71,76 Notes : 1. A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired. 2. The pin 42 is reserved for address bit for the 16Mb . -5- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM FUNCTION DESCRIPTION The K7B803625B and K7B801825B are synchronous SRAM designed to support the burst address accessing sequence of the Power PC based microprocessor. All inputs (with the exception of OE, LBO and ZZ) are sampled on rising clock edges. The start and duration of the burst access is controlled by ADSC, ADSP and ADV and chip select pins. The accesses are enabled with the chip select signals and output enabled signals. Wait states are inserted into the access with ADV. When ZZ is pulled high, the SRAM will enter a Power Down State. At this time, internal state of the SRAM is preserved. When ZZ returns to low, the SRAM normally operates after 2cycles of wake up time. ZZ pin is pulled down internally. Read cycles are initiated with ADSP(or ADSC) using the new external address clocked into the on-chip address register when both GW and BW are high or when BW is low and WEa, WEb, WEc, and WEd are high. When ADSP is sampled low, the chip selects are sampled active, and the output buffer is enabled with OE. the data of cell array accessed by the current address are projected to the output pins. Write cycles are also initiated with ADSP(or ADSC) and are differentiated into two kinds of operations; All byte write operation and individual byte write operation. All byte write occurs by enabling GW(independent of BW and WEx.), and individual byte write is performed only when GW is high and BW is low. In K7B803625B, a 256Kx36 organization, WEa controls DQa0 ~ DQa7 and DQPa, WEb controls DQb0 ~ DQb7 and DQPb, WEc controls DQc0 ~ DQc7 and DQPc and WEd controls DQd0 ~ DQd7 and DQPd. CS1 is used to enable the device and conditions internal use of ADSP and is sampled only when a new external address is loaded. ADV is ignored at the clock edge when ADSP is asserted, but can be sampled on the subsequent clock edges. The address increases internally for the next access of the burst when ADV is sampled low. Addresses are generated for the burst access as shown below, The starting point of the burst sequence is provided by the external address. The burst address counter wraps around to its initial state upon completion. The burst sequence is determined by the state of the LBO pin. When this pin is Low, linear burst sequence is selected. And this pin is High, Interleaved burst sequence is selected. BURST SEQUENCE TABLE LBO PIN HIGH First Address Fourth Address (Interleaved Burst) Case 1 A1 0 0 1 1 Case 2 A0 0 1 0 1 A1 0 0 1 1 Case 3 A0 1 0 1 0 A1 1 1 0 0 Case 4 A0 0 1 0 1 A1 1 1 0 0 BQ TABLE LBO PIN A0 1 0 1 0 (Linear Burst) LOW First Address Fourth Address Case 1 A1 0 0 1 1 Case 2 A0 0 1 0 1 A1 0 1 1 0 Case 3 A0 1 0 1 0 A1 1 1 0 0 Case 4 A0 0 1 0 1 A1 1 0 0 1 A0 1 0 1 0 Note : 1. LBO pin must be tied to High or Low, and Floating State must not be allowed. -6- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM TRUTH TABLES SYNCHRONOUS TRUTH TABLE CS1 CS2 CS2 H X X ADSP ADSC X L ADV WRITE CLK ADDRESS ACCESSED OPERATION X X ↑ N/A Not Selected L L X L X X X ↑ N/A Not Selected L X H L X X X ↑ N/A Not Selected L L X X L X X ↑ N/A Not Selected L X H X L X X ↑ N/A Not Selected L H L L X X X ↑ External Address Begin Burst Read Cycle L H L H L X L ↑ External Address Begin Burst Write Cycle L H L H L X H ↑ External Address Begin Burst Read Cycle X X X H H L H ↑ Next Address Continue Burst Read Cycle H X X X H L H ↑ Next Address Continue Burst Read Cycle X X X H H L L ↑ Next Address Continue Burst Write Cycle H X X X H L L ↑ Next Address Continue Burst Write Cycle X X X H H H H ↑ Current Address Suspend Burst Read Cycle H X X X H H H ↑ Current Address Suspend Burst Read Cycle X X X H H H L ↑ Current Address Suspend Burst Write Cycle H X X X H H L ↑ Current Address Suspend Burst Write Cycle Notes : 1. X means "Don′t Care". 2. The rising edge of clock is symbolized by ↑. 3. WRITE = L means Write operation in WRITE TRUTH TABLE. WRITE = H means Read operation in WRITE TRUTH TABLE. 4. Operation finally depends on status of asynchronous input pins(ZZ and OE). WRITE TRUTH TABLE( x36) GW BW WEa WEb WEc WEd OPERATION H H X X X X READ H L H H H H READ H L L H H H WRITE BYTE a H L H L H H WRITE BYTE b H L H H L L WRITE BYTE c and d H L L L L L WRITE ALL BYTEs L X X X X X WRITE ALL BYTEs Notes : 1. X means "Don′t Care". 2. All inputs in this table must meet setup and hold time around the rising edge of CLK(↑). WRITE TRUTH TABLE(x18) GW BW WEa WEb OPERATION H H X X READ H L H H READ H L L H WRITE BYTE a H L H L WRITE BYTE b H L L L WRITE ALL BYTEs L X X X WRITE ALL BYTEs Notes : 1. X means "Don′t Care". 2. All inputs in this table must meet setup and hold time around the rising edge of CLK(↑). -7- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM ASYNCHRONOUS TRUTH TABLE Operation ZZ OE I/O STATUS Sleep Mode H X High-Z L L DQ Read L H High-Z Write L X Din, High-Z Deselected L X High-Z Notes 1. X means "Don′t Care". 2. ZZ pin is pulled down internally 3. For write cycles that following read cycles, the output buffers must be disabled with OE, otherwise data bus contention will occur. 4. Sleep Mode means power down state of which stand-by current does not depend on cycle time. 5. Deselected means power down state of which stand-by current depends on cycle time. ABSOLUTE MAXIMUM RATINGS* PARAMETER SYMBOL RATING UNIT Voltage on VDD Supply Relative to VSS VDD -0.3 to 4.6 V Voltage on VDDQ Supply Relative to VSS VDDQ VDD V Voltage on Input Pin Relative to VSS VIN -0.3 to VDD+0.3 V Voltage on I/O Pin Relative to VSS VIO -0.3 to VDDQ+0.3 V Power Dissipation Storage Temperature Commercial Operating Temperature Industrial Storage Temperature Range Under Bias PD 1.6 W TSTG -65 to 150 °C TOPR 0 to 70 °C TOPR -40 to 85 °C TBIAS -10 to 85 °C *Note : Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. OPERATING CONDITIONS at 3.3V I/O(0°C ≤ TA ≤ 70°C) PARAMETER Supply Voltage Ground SYMBOL MIN Typ. MAX UNIT VDD 3.135 3.3 3.465 V VDDQ 3.135 3.3 3.465 V VSS 0 0 0 V * The above parameters are also guaranteed at industrial temperature range. OPERATING CONDITIONS at 2.5V I/O(0°C ≤ TA ≤ 70°C) PARAMETER Supply Voltage Ground SYMBOL MIN Typ. MAX UNIT VDD 3.135 3.3 3.465 V VDDQ 2.375 2.5 2.9 V VSS 0 0 0 V * The above parameters are also guaranteed at industrial temperature range. CAPACITANCE*(TA=25°C, f=1MHz) PARAMETER Input Capacitance Output Capacitance SYMBOL TEST CONDITION MIN MAX UNIT CIN VIN=0V - 5 pF COUT VOUT=0V - 7 pF *Note : Sampled not 100% tested. -8- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM DC ELECTRICAL CHARACTERISTICS(VDD=3.3V+0.165V/-0.165V, TA=0°C to +70°C) Parameter Symbol Test Conditions Min Max Unit Input Leakage Current(except ZZ) IIL VDD=Max ; VIN=VSS to VDD -2 +2 µA Output Leakage Current IOL Output Disabled, Vout=VSS to VDDQ -2 +2 µA Operating Current ICC ISB Device Selected, IOUT=0mA, -65 - 300 ZZ≤VIL , Cycle Time ≥ tCYC Min -75 - 280 Device deselected, IOUT=0mA, -65 - 140 -75 - 130 - 100 mA - 60 mA 0.4 V ZZ≤VIL, f=Max, All Inputs≤0.2V or ≥ VDD-0.2V Standby Current ISB1 ISB2 Device deselected, IOUT=0mA, ZZ≤0.2V, f=0, All Inputs=fixed (VDD-0.2V or 0.2V) Device deselected, IOUT=0mA, ZZ≥VDD-0.2V, f=Max, All Inputs≤VIL or ≥VIH Notes mA 1,2 mA Output Low Voltage(3.3V I/O) VOL IOL=8.0mA - Output High Voltage(3.3V I/O) VOH IOH=-4.0mA 2.4 - V Output Low Voltage(2.5V I/O) VOL IOL=1.0mA - 0.4 V Output High Voltage(2.5V I/O) VOH IOH=-1.0mA Input Low Voltage(3.3V I/O) VIL 2.0 - V -0.3* 0.8 V Input High Voltage(3.3V I/O) VIH 2.0 VDD+0.3 V Input Low Voltage(2.5V I/O) VIL -0.3* 0.7 V Input High Voltage(2.5V I/O) VIH 1.7 VDD+0.3 V 3 3 Notes : The above parameters are also guaranteed at industrial temperature range. 1. Reference AC Operating Conditions and Characteristics for input and timing. 2. Data states are all zero. 3. In Case of I/O Pins, the Max. VIH=VDDQ+0.3V VIH VSS VSS-1.0V 20% tCYC(MIN) TEST CONDITIONS (VDD=3.3V+0.165V/-0.165V,VDDQ=3.3V+0.165/-0.165V or VDD=3.3V+0.165V/-0.165V,VDDQ=2.5V+0.4V/-0.125V, TA=0to70°C) PARAMETER VALUE Input Pulse Level(for 3.3V I/O) 0 to 3.0V Input Pulse Level(for 2.5V I/O) 0 to 2.5V Input Rise and Fall Time(Measured at 20% to 80% for 3.3V I/O) 1.0V/ns Input Rise and Fall Time(Measured at 20% to 80% for 2.5V I/O) 1.0V/ns Input and Output Timing Reference Levels for 3.3V I/O 1.5V Input and Output Timing Reference Levels for 2.5V I/O VDDQ/2 Output Load See Fig. 1 * The above parameters are also guaranteed at industrial temperature range. -9- Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Output Load(B), (for tLZC, tLZOE, tHZOE & tHZC) Output Load(A) +3.3V for 3.3V I/O /+2.5V for 2.5V I/O RL=50Ω Dout Zo=50Ω 30pF* VL=1.5V for 3.3V I/O VDDQ/2 for 2.5V I/O 319Ω / 1667Ω Dout 353Ω / 1538Ω 5pF* * Including Scope and Jig Capacitance Fig. 1 AC TIMING CHARACTERISTICS(VDD=3.3V+0.165V/-0.165V, TA=0°C to +70°C) PARAMETER SYMBOL Cycle Time -65 -75 UNIT MIN MAX MIN MAX tCYC 7.5 - 8.5 - ns Clock Access Time tCD - 6.5 - 7.5 ns Output Enable to Data Valid tOE - 3.5 - 3.5 ns Clock High to Output Low-Z tLZC 2.5 - 2.5 - ns Output Hold from Clock High tOH 2.5 - 2.5 - ns Output Enable Low to Output Low-Z tLZOE 0 - 0 - ns Output Enable High to Output High-Z tHZOE - 3.5 - 3.5 ns Clock High to Output High-Z tHZC - 3.8 - 4.0 ns Clock High Pulse Width tCH 2.2 - 2.5 - ns Clock Low Pulse Width tCL 2.2 - 2.5 - ns Address Setup to Clock High tAS 1.5 - 2.0 - ns Address Status Setup to Clock High tSS 1.5 - 2.0 - ns Data Setup to Clock High tDS 1.5 - 2.0 - ns tWS 1.5 - 2.0 - ns Address Advance Setup to Clock High tADVS 1.5 - 2.0 - ns Chip Select Setup to Clock High tCSS 1.5 - 2.0 - ns Address Hold from Clock High tAH 0.5 - 0.5 - ns Address Status Hold from Clock High tSH 0.5 - 0.5 - ns Data Hold from Clock High tDH 0.5 - 0.5 - ns Write Hold from Clock High (GW, BW, WEX) tWH 0.5 - 0.5 - ns Address Advance Hold from Clock High tADVH 0.5 - 0.5 - ns Chip Select Hold from Clock High tCSH 0.5 - 0.5 - ns ZZ High to Power Down tPDS 2 - 2 - cycle ZZ Low to Power Up tPUS 2 - 2 - cycle Write Setup to Clock High (GW, BW, WEX) Notes : 1. The above parameters are also guaranteed at industrial temperature range. 2. All address inputs must meet the specified setup and hold times for all rising clock edges whenever ADSC and/or ADSP is sampled low and CS is sampled low. All other synchronous inputs must meet the specified setup and hold times whenever this device is chip selected. 3. Both chip selects must be active whenever ADSC or ADSP is sampled low in order for the this device to remain enabled. 4. ADSC or ADSP must not be asserted for at least 2 Clock after leaving ZZ state. - 10 - Nov. 2003 Rev 3.0 - 11 - Data Out OE ADV CS WRITE ADDRESS ADSC ADSP CLOCK tCSS tAS tSS tOE Q1-1 tHZOE tADVH tWH tSS A2 tSH Q2-1 tCD tOH Q2-2 Q2-3 A3 Q2-4 (ADV INSERTS WAIT STATE) BURST CONTINUED WITH NEW BASE ADDRESS tCYC tCL NOTES : WRITE = L means GW = L, or GW = H, BW = L, WEx.= L CS = L means CS1 = L, CS2 = H and CS2 = L CS = H means CS1 = H, or CS1 = L and CS2 = H, or CS1 = L, and CS2 = L tADVS tCSH tWS tLZOE A1 tAH tSH tCH TIMING WAVEFORM OF READ CYCLE Q3-1 Q3-2 Q3-3 Undefined Don′t Care Q3-4 tHZC K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Nov. 2003 Rev 3.0 - 12 - Data Out Data In OE ADV CS WRITE ADDRESS ADSC ADSP CLOCK Q0-3 tCSS tAS tSS Q0-4 A1 tLZOE tCSH tAH tSH D1-1 tCH tCYC tCL A2 D2-1 D2-2 (ADV SUSPENDS BURST) D2-2 D2-3 (ADSC EXTENDED BURST) TIMING WAVEFORM OF WRTE CYCLE D2-4 D3-1 A3 tDS tADVS tWS tSS D3-2 tDH tADVH tWH tSH D3-3 Undefined Don′t Care D3-4 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Nov. 2003 Rev 3.0 - 13 - Data Out Data In OE ADV CS WRITE ADDRESS ADSP CLOCK tHZC tSS A1 tLZC tCD tSH Q1-1 tHZOE tAS A2 tCL tCYC tDS tADVS tWS tAH tCH D2-1 tDH tADVH tWH A3 tLZOE tOE Q3-1 Q3-2 Q3-3 tOH Q3-4 TIMING WAVEFORM OF COMBINATION READ/WRTE CYCLE(ADSP CONTROLLED, ADSC=HIGH) Undefined Don′t Care K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Nov. 2003 Rev 3.0 - 14 - Data In Data Out OE ADV CS WRITE ADDRESS ADSC CLOCK tCSS tSS A1 tLZOE tOE tCSH tSH Q1-1 A2 Q2-1 A3 Q3-1 A4 Q4-1 tHZOE D5-1 A5 tDS tWS D6-1 A6 tDH tWH D7-1 A7 tWS tCD A8 A9 Q8-1 tCL tCYC tWH tCH TIMING WAVEFORM OF SINGLE READ/WRITE CYCLE(ADSC CONTROLLED, ADSP=HIGH) Undefined Don′t Care Q9-1 tOH K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Nov. 2003 Rev 3.0 - 15 - Data In Data Out OE ADV CS WRITE ADDRESS ADSP CLOCK tCSS tSS tOE tCSH tLZOE A1 tSH Q1-1 A2 Q2-1 A3 tAS Q3-1 A4 tAH tCYC tCH A5 Q4-1 tCL tHZOE D5-1 A6 tDS D6-1 tDH A7 D7-1 tCD A8 Q8-1 A9 TIMING WAVEFORM OF SINGLE READ/WRITE CYCLE(ADSP CONTROLLED, ADSC=HIGH) Q9-1 tOH Undefined Don′t Care K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Nov. 2003 Rev 3.0 - 16 - ZZ Data Out Data In OE ADV CS WRITE ADDRESS ADSC ADSP CLOCK tCSS tAS tSS A1 tLZOE tOE tCSH tAH tSH Q1-1 ZZ Setup Cycle tPDS tHZC Sleep State ZZ Recovery Cycle tPUS tCL tCYC tCH TIMING WAVEFORM OF POWER DOWN CYCLE tWS Normal Operation Mode tHZOE A2 D2-1 tWH Undefined Don′t Care D2-2 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM APPLICATION INFORMATION DEPTH EXPANSION The Samsung 256Kx36 Synchronous Burst SRAM has two additional chip selects for simple depth expansion. This permits easy secondary cache upgrades from 256K depth to 512K depth without extra logic. I/O[0:71] Data Address A[0:18] A[18] A[0:17] A[18] A[0:17] Address Data Address Data CLK CS2 CS2 CS2 CS2 CLK Microprocessor Address ADSC CLK WEx OE Cache Controller CLK 256Kx36 SB SRAM ADSC WEx (Bank 0) OE (Bank 1) CS1 CS1 ADV 256Kx36 SB SRAM ADV ADSP ADSP ADS INTERLEAVE READ TIMING (Refer to non-interleave write timing for interleave write timing) (ADSP CONTROLLED , ADSC=HIGH) CLOCK tSS tSH ADSP tAS ADDRESS [0:n] tAH A1 A2 tWS tWH WRITE tCSS tCSH CS1 Bank 0 is selected by CS2, and Bank 1 deselected by CS2 An+1 tADVS Bank 0 is deselected by CS2, and Bank 1 selected by CS2 tADVH ADV OE tOE Data Out (Bank 0) Data Out (Bank 1) tLZOE tHZC Q1-1 Q1-2 Q1-3 Q1-4 tCD tLZC Q2-1 *Notes : n = 14 32K depth , 16 128K depth , 18 512K depth 15 64K depth 17 256K depth Q2-2 Q2-3 Q2-4 Don′t Care - 17 - Undefined Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM APPLICATION INFORMATION DEPTH EXPANSION The Samsung 512Kx18 Synchronous Burst SRAM has two additional chip selects for simple depth expansion. This permits easy secondary cache upgrades from 512K depth to 1M depth without extra logic. I/O[0:71] Data Address A[19] A[0:19] A[19] A[0:18] Address Data Address Data CLK Microprocessor CS2 CS2 CS2 CS2 CLK Address ADSC CLK WEx OE Cache Controller A[0:18] 512Kx18 SB SRAM CLK ADSC WEx (Bank 0) OE (Bank 1) CS1 CS1 ADV 512Kx18 SB SRAM ADV ADSP ADSP ADS INTERLEAVE READ TIMING (Refer to non-interleave write timing for interleave write timing) (ADSP CONTROLLED , ADSC=HIGH) CLOCK tSS tSH ADSP tAS ADDRESS [0:n] tAH A1 A2 tWS tWH WRITE tCSS tCSH CS1 Bank 0 is selected by CS2, and Bank 1 deselected by CS2 An+1 tADVS Bank 0 is deselected by CS2, and Bank 1 selected by CS2 tADVH ADV OE tOE Data Out (Bank 0) Data Out (Bank 1) tLZOE tHZC Q1-1 Q1-2 Q1-3 Q1-4 tCD tLZC Q2-1 *Notes : n = 14 32K depth , 16 128K depth , 18 512K depth , 15 64K depth 17 256K depth 19 1M depth Q2-2 Q2-3 Q2-4 Don′t Care - 18 - Undefined Nov. 2003 Rev 3.0 K7B803625B K7B801825B 256Kx36 & 512Kx18 Synchronous SRAM PACKAGE DIMENSIONS 100-TQFP-1420A Units ; millimeters/Inches 0~8° 22.00 ±0.30 0.10 0.127 +- 0.05 20.00 ±0.20 16.00 ±0.30 14.00 ±0.20 0.10 MAX (0.83) 0.50 ±0.10 #1 0.65 (0.58) 0.30 ±0.10 0.10 MAX 1.40 ±0.10 1.60 MAX 0.50 ±0.10 - 19 - 0.05 MIN Nov. 2003 Rev 3.0