Ordering number:EN650C Diffused Junction Silicon Diode DBA60 6.0A Single-Phase Bridge Rectifier Features Package Dimensions · Plastic molded structure. · Glass passivation for high reliability. · Peak reverse voltage:VRM=100 to 400V. · Average rectified current :IO=6.0A. unit:mm 1091 [DBA60] Specifications Absolute Maximum Ratings at Ta = 25˚C Parameter Peak Reverse Voltage Symbol Conditions DBA60B DBA60C DBA60E Average Recitified Current VRM IO Surge Forward Current IFSM Junction Temperature Tj → → 150 Storage Temperature Tstg → → –30 to +150 Unit –100 –200 –400 V Ta=40˚C Ta=40˚C, mounted on 80×80×1.5mm3 AI fin → → 3.5 A → → 6.0 A 50Hz sine wave, 1 cycle → → 200 A ˚C ˚C Electrical Characteristics at Ta=25˚C, per constituent element of bridge Parameter Forward Voltage Reverse Current Symbol VF IR Conditions Rating min typ max Unit IF=3.0A 1.05 V VR:At each VRM –10 µA Note1 : Mounting Torque : 5kg·cm max SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquaters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 43098GI/8033KI, TS No.650-1/2 DBA60 IO — Ta Resistive,inductive load 6 5 L Capacitive load L=25mm 4 15mm L=25mm 3 15mm 5mm 5mm 2 1 With 80×80×1.5mm3 Al fin 0 0 20 40 60 80 IO — Ta 5 Average Rectifed Current, IO — A Average Rectifed Current, IO — A 7 100 120 140 L 4 Resistive,inductive load 2 5mm 1 No fin 20 40 60 80 100 120 140 160 3.5 5.0 Ambient Temperature, Ta — ˚C Fin Size(half side) — IO IF — VF ˚C 10 Ta=40˚C Fin:1.5mm Al fin 5 7 5 3 2 10 3 Ta=150 7 100 Forward Current, IF — A Fin Size(Half Side) — cm2 5mm 15mm Ambient Temperature, Ta — ˚C 2 15mm L=25mm 0 0 160 L=25mm Capacitive load 3 2 1.0 7 5 3 2 7 5 3 4 5 6 7 0.1 8 0 0.5 1.0 Average Rectified Current, IO — A IFSM — n 5 200 Solder Temperature — ˚C Surge Forward Current, IFSM — A 240 1.5 2.0 2.5 3.0 Forward Voltage, VF — V 160 120 50H z 80 Soldering Temperature — t L=1 5mm 4 10m m 3 5mm 1.5m m 2 40 L 0 1.0 2 3 5 7 10 2 3 Number of Cycles at 50Hz, n 5 7 100 100 1.0 2 3 5 7 2 10 Solder Dip Time — s No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. Anyone purchasing any products described or contained herein for an above-mentioned use shall: Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: Not impose any responsibilty for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of April, 1998. Specifications and information herein are subject to change without notice. PS No.650-2/2