Ordering number: EN5191A Bi-CMOS LSI LV3403M 3 V Operation Filter for FM Multiplex Broadcasting Reception Overview Package Dimensions The LV3403M is a filter IC for FM multiplex broadcasting reception which is used in combination with demodulationerror correction IC (LC72703). The use of switched capacitor filter (SCF) technique obviates the need for frequency adjustment and ensures stable operation. unit : mm 3111-MFP14S [LV3403M] Functions . 76 kHz BPF (Gaussian filter) . 54 kHz HPF . 125 kHz LPF . Anti-aliasing filter . Limiter circuit SANYO : MFP14S Features . No adjustments needed due to SCF-used configuration. . Few external components needed. Specifications Maximum Ratings at Ta = 25 °C Parameter¬ Symbol¬ Maximum supply voltage¬ VCC max¬ Maximum input voltage¬ VIN max¬ Allowable power dissipation¬ Pd max¬ Conditions¬ Ratings¬ Unit 6¬ SIG.IN, CLK IN pin¬ –0.3 to VCC +0.3¬ V V 180¬ mW Operating temperature¬ Topr¬ –20 to +70¬ °C Storage temperature¬ Tstg¬ –55 to +125¬ °C Operating Conditions at Ta = 25 °C Parameter¬ Symbol¬ Recommended supply voltage¬ VCC Operating supply voltage range¬ VCC op¬ Input voltage range¬ VIN Conditions¬ Ratings¬ 3 Base band signal equivalent to FM: 100% modulation fIN = 76 kHz, CW¬ Clock frequency¬ fck¬ Rectangular wave¬ Clock input voltage¬ Vck¬ Rectangular wave¬ Unit V 2.7 to 4.5¬ V 200 to 300¬ mVrms 8 to 30¬ mVrms 3.60¬ 1.0 to VCC MHz Vp-p SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 62096HA(II)/81095HA(II) No.5191-1/3 LV3403M Electrical Characteristics at Ta = 25 °C, VCC = 3 V, fck = 3.6 MHz, Vck = 1 Vp-p Parameter¬ Current drain¬ SCF block common voltage¬ Input signal resistance¬ Clock input resistance¬ [MSK Output] Symbol¬ ICCO V2 RIN3 RIN12 Input sensitivity¬ V3S Output high-level voltage¬ Output low-level voltage¬ V10H V10L Conditions¬ Current on pin 14 when VIN = no signal¬ Voltage on pin 2 when VIN = no signal¬ Pin 3 input resistance¬ Pin 12 input resistance¬ fIN = 76 kHz, the input level at which MSK output is the same frequency when CW is applied VIN = 76 kHz, 4 mVrms, CW¬ VIN = 76 kHz, 4 mVrms, CW¬ min¬ 3.5¬ 1.2¬ typ¬ 5¬ 1.4¬ 36¬ 5¬ max¬ 6.5¬ 1.6¬ Unit mA V kΩ kΩ 4¬ mVrms 2.5¬ 0.4¬ V V Reference Characteristics Ratings¬ Unit AAF cut-off frequency¬ Parameter¬ 300¬ kHz HPF corner frequency¬ 54¬ kHz LPF cut-off frequency¬ 125¬ kHz BPF center frequency¬ 76¬ kHz BPF –3 dB frequency¬ 19¬ kHz Difference in maximum group delay within band¬ ±5 µs Group delay Group delay –µs Gain, G – dB Integrated Characteristics Input frequency, fIN – kHz Pin Assignment Top view No.5191-2/3 LV3403M Pin Descriptions Pin No.¬ Pin name¬ Description 1¬ GND¬ Ground. 2 VCOM Common for SCF section. Connect to decoupling capacitor. 3¬ SIG.IN¬ Signal input. Input a frequency-modulated signal (composite signal) at 200 to 300 mVrms. When inputting 76 kHz only, the input sensitivity is 4 mVrms or less. 10¬ MSK OUT¬ 11¬ VREF 12¬ CLK IN 14¬ VCC 5, 8, 13¬ TEST PIN¬ 4, 6, 7, 9¬ NC¬ MSK output (CMOS output.) Limiter reference pin. Form an LPF with the 10 kΩ internal resistor and an external capacitor. 3.6 MHz clock input. Because the DC bias is output by the limiter amplifier input, the clock is input with capacitor coupling. Power supply Test pin. Leave open. Unused. Notes on usage: (1) When using this IC, leave pins 4 to 9 and pin 13 open. (2) The clock is connected to pin 12 from the decoder (LC72700) clock output pin through a 100 pF capacitor. In addition, by inserting a resistor in the clock line, it is possible to dampen the rising and falling edges, reducing spurious radiation. Equivalent Circuit Block Diagram Clock input MSK output Dual-mode clock generator Bias circuit SIG. input 76 kHz CW Note : Pins 4 through 9 and pin 13 must be left open. No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. Anyone purchasing any products described or contained herein for an above-mentioned use shall: 1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: 2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of June, 1996. Specifications and information herein are subject to change without notice. No.5191-3/3