74LCXU04 LOW VOLTAGE CMOS HEX INVERTER(SINGLE STAGE) WITH 5V TOLERANT INPUTS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 5V TOLERANT INPUTS HIGH SPEED: tPD = 5.2ns (MAX.) at VCC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) at VCC = 3V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2.0V to 3.6V (1.5V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES U04 LATCH-UP PERFORMANCE EXCEEDS 500mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V DESCRIPTION The 74LCXU04 is a low voltage CMOS HEX INVERTER (SINGLE STATE) fabricated with sub-micron silicon gate and double-layer metal SOP TSSOP Table 1: Order Codes PACKAGE T&R SOP TSSOP 74LCXU04MTR 74LCXU04TTR wiring C2MOS technology. It is ideal for low power and high speed 3.3V applications. It can be interfaced to 5V signal environment for inputs. It has same speed performance at 3.3V than 5V AC/ACT family, combined with a lower power consumption. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols September 2004 Rev. 4 1/11 74LCXU04 Figure 2: Input And Output Equivalent Circuit Table 2: Pin Description Table 3: Truth Table PIN N° SYMBOL 1,3,5,9,11,13 2, 4, 6, 8, 10, 12 7 1A to 6A Data Inputs 1Y to 6Y Data Outputs GND VCC Ground (0V) 14 NAME AND FUNCTION A Y L H H L Positive Supply Voltage Table 4: Absolute Maximum Ratings Symbol VCC Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage (VCC = 0V) -0.5 to +7.0 V VO DC Output Voltage (High or Low State) (note 1) IIK DC Input Diode Current IOK IO -0.5 to VCC + 0.5 V - 50 mA DC Output Diode Current (note 2) - 50 mA DC Output Current ± 50 mA ± 100 mA ICC DC Supply Current per Supply Pin IGND DC Ground Current per Supply Pin Tstg Storage Temperature TL Lead Temperature (10 sec) ± 100 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND 2/11 74LCXU04 Table 5: Recommended Operating Conditions Symbol VCC Parameter Supply Voltage (note 1) Value Unit 2.0 to 3.6 V VI Input Voltage 0 to 5.5 V VO Output Voltage (VCC = 0V) 0 to 5.5 V VO Output Voltage (High or Low State) 0 to VCC V ± 24 mA IOH, IOL High or Low Level Output Current (VCC = 3.0 to 3.6V) IOH, IOL High or Low Level Output Current (VCC = 2.7V) Top dt/dv Operating Temperature Input Rise and Fall Time (note 2) ± 12 mA -55 to 125 °C 0 to 10 ns/V 1) Truth Table guaranteed: 1.5V to 3.6V 2) VIN from 0.8V to 2V at VCC = 3.0V Table 6: DC Specifications Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Ioff ICC ∆ICC Input Leakage Current Power Off Leakage Current Quiescent Supply Current ICC incr. per Input Min. Max. 2.0 -55 to 125 °C Min. Unit Max. 2.0 V 2.7 to 3.6 0.8 0.8 2.7 to 3.6 IO=-100 µA VCC-0.2 VCC-0.2 2.7 IO=-12 mA 2.2 2.2 IO=-18 mA 2.4 2.4 IO=-24 mA 2.2 2.2 V V 2.7 to 3.6 IO=100 µA 0.2 0.2 2.7 IO=12 mA 0.4 0.4 IO=16 mA 0.4 0.4 IO=24 mA 0.55 0.55 2.7 to 3.6 VI = 0 to 5.5V ±5 ±5 µA 0 VI or VO = 5.5V 10 10 µA 2.7 to 3.6 VI = VCC or GND VI or VO= 3.6 to 5.5V 10 10 ± 10 ± 10 2.7 to 3.6 VIH = VCC - 0.6V 500 500 3.0 II -40 to 85 °C VCC (V) 3.0 VOL Value V µA µA Table 7: Dynamic Switching Characteristics Test Condition Symbol VOLP VOLV Parameter Dynamic Low Level Quiet Output (note 1) TA = 25 °C VCC (V) 3.3 Value Min. CL = 50pF VIL = 0V, VIH = 3.3V Typ. 0.8 -0.8 Unit Max. V 1) Number of outputs defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. 3/11 74LCXU04 Table 8: AC Electrical Characteristics Test Condition Symbol tPLH tPHL tOSLH tOSHL Parameter Propagation Delay Time Output To Output Skew Time (note1, 2) VCC (V) 2.7 3.0 to 3.6 3.0 to 3.6 Value CL (pF) RL (Ω) ts = tr (ns) 50 500 2.5 50 500 2.5 -40 to 85 °C -55 to 125 °C Min. Max. Min. Max. 1.0 6.0 5.2 1.0 1.0 6.0 5.2 1.0 Unit ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|) 2) Parameter guaranteed by design Table 9: Capacitive Characteristics Test Condition Symbol Parameter Value TA = 25 °C VCC (V) Min. Typ. CIN Input Capacitance 3.3 VIN = 0 to VCC 6 CPD Power Dissipation Capacitance (note 1) 3.3 fIN = 10MHz VIN = 0 or VCC 50 Unit Max. pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate) Figure 3: Test Circuit CL = 50 pF or equivalent (includes jig and probe capacitance) RL = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) 4/11 74LCXU04 Figure 4: Waveform - Propagation Delay (f=1MHz; 50% duty cycle) 5/11 74LCXU04 SO-14 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 0.344 E 3.8 4.0 0.150 0.157 e 1.27 0.050 H 5.8 6.2 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.4 1.27 0.016 0.050 k 0° 8° 0° 8° ddd 0.100 0.004 0016019D 6/11 74LCXU04 TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 7/11 74LCXU04 Tape & Reel SO-14 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 8/11 TYP 0.504 22.4 0.519 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 74LCXU04 Tape & Reel TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 9/11 74LCXU04 Table 10: Revision History Date Revision 15-Sep-2004 4 10/11 Description of Changes Ordering Codes Revision - pag. 1. 74LCXU04 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 11/11