74V1G05 SINGLE INVERTER (OPEN DRAIN) PRELIMINARY DATA ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 3.7 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1 µA (MAX.) at TA = 25 oC HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) POWER DOWN PROTECTION ON INPUT OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 5.5V IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74V1G05 is an advanced high-speed CMOS SINGLE INVERTER (OPEN DRAIN) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. The internal circuit is composed of 3 stages including buffer output, which provide high noise S (SOT23-5L) C (SC-70) ORDER CODE: 74V1G05S 74V1G05C immunity and stable output. Power down protection is provided on input and 0 to 7V can be accepted on input with no regard to the supply voltage. This device can be used to interface 5V to 3V. PIN CONNECTION AND IEC LOGIC SYMBOLS September 1999 1/7 74V1G05 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 N.C. NAME AND FUNCT ION 2 1A Data Input 4 1Y Data Output 3 GND Ground (0V) 5 VCC Positive Supply Voltage Not Connected TRUTH TABLE A Y L Z H L Z: High Impedance ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current 25 mA ± 50 mA VCC ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) -65 to +150 o 260 o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. RECOMMENDED OPERATING CONDITIONS Symbol Parameter 2.0 to 5.5 V Input Voltage 0 to 5.5 V VO Output Voltage 0 to VCC Top dt/dv Operating Temperature Input Rise and Fall Time (see note 1) (VCC = 3.3 ± 0.3V) (V CC = 5.0 ± 0.5V) 1) VIN from 30% to70%of VCC 2/7 Unit VI VCC Supply Voltage Valu e -40 to +85 0 to 100 0 to 20 V o C ns/V ns/V 74V1G05 DC SPECIFICATIONS Symb ol VIH VIL VOL Parameter T est Cond ition s Min. II ICC Typ . Un it -40 to 85 o C Max. Min . Max. High Level Input Voltage 2.0 1.5 1.5 3.0 to 5.5 0.7VCC 0.7VCC Low Level Input Voltage 2.0 0.5 0.5 3.0 to 5.5 0.3VCC 0.3VCC Low Level Output Voltage High Impedance Output Leakage Current Input Leakage Current Quiescent Supply Current V 2.0 I O=50 µA 0.0 0.1 0.1 3.0 IO=50 µA IO=50 µA 0.0 0.1 0.1 0.0 0.1 0.1 4.5 IOZ Value T A = 25 o C V CC (V) V V 3.0 IO=4 mA 0.36 0.44 4.5 IO=8 mA 0.36 0.44 VI = VIH or VIL VO = VCC or GND ±0.25 ±2.5 µA 5.5 0 to 5.5 VI = 5.5V or GND ±0.1 ±1.0 µA 5.5 VI = VCC or GND 2 20 µA AC ELECTRICAL CHARACTERISTICS (Input tr = tf =3 ns) Symbol Parameter V CC (V) tPZL tPLZ Propagation Delay Time Propagation Delay Time T est Conditio n CL (p F) 3.3 (*) 3.3 (*) 5.0(**) 5.0(**) 3.3 (*) 15 50 15 50 50 RL RL RL RL RL (**) 50 R L = 1 KΩ 5.0 Valu e T A = 25 o C Min. = 1 KΩ = 1 KΩ = 1 KΩ = 1 KΩ = 1 KΩ Unit -40 to 85 o C T yp. 5.5 8.0 3.7 5.2 9.0 Max. 7.9 11.4 5.5 7.5 11.4 Min. 1.0 1.0 1.0 1.0 1.0 Max. 9.5 13.0 6.5 8.5 13.0 6.0 7.5 1.0 8.5 ns ns (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5V ± 0.5V CAPACITIVE CHARACTERISTICS Symb ol Parameter T est Cond ition s Value T A = 25 o C Min. C IN Input Capacitance Un it -40 to 85 o C Typ . Max. 4 10 Min . Max. 10 pF COUT Output Capacitance 5 pF CPD Power Dissipation Capacitance (note 1) 6 pF 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operating current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC 3/7 74V1G05 TEST CIRCUIT CL = 15/50 pF or equivalent (includes jig and probe capacitance) RL = R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 4/7 74V1G05 SOT23-5L MECHANICAL DATA mm DIM. MIN. TYP. mils MAX. MIN. TYP. MAX. A 0.90 1.45 35.4 57.1 A1 0.00 0.15 0.0 5.9 A2 0.90 1.30 35.4 51.2 b 0.35 0.50 13.7 19.7 C 0.09 0.20 3.5 7.8 D 2.80 3.00 110.2 118.1 E 2.60 3.00 102.3 118.1 E1 1.50 1.75 59.0 68.8 L 0.35 0.55 13.7 21.6 e 0.95 37.4 e1 1.9 74.8 5/7 74V1G05 SC-70 MECHANICAL DATA mm DIM. MIN. 6/7 TYP. mils MAX. MIN. TYP. MAX. A 0.80 1.10 31.5 43.3 A1 0.00 0.10 0.0 3.9 A2 0.80 1.00 31.5 39.4 b 0.15 0.30 5.9 11.8 C 0.10 0.18 3.9 7.1 D 1.80 2.20 70.9 86.6 E 1.80 2.40 70.9 94.5 E1 1.15 1.35 45.3 53.1 L 0.10 0.30 3.9 11.8 e 0.65 25.6 e1 1.3 51.2 74V1G05 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 7/7