HCC/HCF4013B DUAL ’D’ – TYPE FLIP–FLOP .. . . . .. .. SET-RESET CAPABILITY STATIC FLIP-FLOP OPERATION - RETAINS STATE INDEFINITELY WITH CLOCK LEVEL EITHER ”HIGH” OR ”LOW” MEDIUM-SPEED OPERATION - 16MHz (typ.) CLOCK TOGGLE RATE AT 10V QUIESCENT CURRENT SPECIFIED TO 20V FOR HCC DEVICE STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS 5V, 10V, AND 15V PARAMETRIC RATINGS INPUT CURRENT OF 100nA AT 18V AND 25°C FOR HCC DEVICE 100% TESTED FOR QUIESCENT CURRENT MEETS ALL REQUIREMENTS OF JEDEC TENTATIVE STANDARD No. 13A, ”STANDARD SPECIFICATIONS FOR DESCRIPTION OF ”B” SERIES CMOS DEVICES” EY (Plastic Package) M1 (Micro Package) F (Ceramic Frit Seal Package) C1 (Plastic Chip Carrier) ORDER CODES : HCC4013BF HCF4013BM1 HCF4013BEY HCF4013BC1 PIN CONNECTIONS DESCRIPTION The HCC4013B (extended temperature range) and HCF4013B (intermediate temperature range) are monolithic integrated circuits, available in 14-lead dual in-line plastic or ceramic package and plastic micropackage. The HCC/HCF4013B consists of two identical, independent data-type flip-flops. Each flip-flop has independent data, set, reset, and clock inputs and Q and Q outputs. These devices can be used for shift register applications, and, by connecting Q output to the data input, for counter and toggle applications. The logic level present at the D input is transferred to the Q output during the positive-going transition of the clock pulse. Setting or resetting is independent of the clock and is accomplished by a high level on the set or reset line, respectively. June 1989 1/11 HCC/HFC4013B ABSOLUTE MAXIMUM RATINGS Symbol V DD* Parameter Supply Voltage : HCC Types HC F Types Value Unit – 0.5 to + 20 – 0.5 to + 18 V V Vi Input Voltage – 0.5 to V DD + 0.5 V II DC Input Current (any one input) ± 10 mA Total Power Dissipation (per package) Dissipation per Output Transistor for T o p = Full Package-temperature Range 200 mW 100 mW Pt ot Top Operating Temperature : HCC Types H CF Types – 55 to + 125 – 40 to + 85 °C °C Tstg Storasge Temperature – 65 to + 150 °C Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability. * All voltages are with respect to VSS (GND). RECOMMENDED OPERATING CONDITIONS Symbol V DD VI Top Parameter Value Unit 3 to 18 3 to 15 V V 0 to V DD V – 55 to + 125 – 40 to + 85 °C °C Supply Voltage : HCC Types HC F Types Input Voltage Operating Temperature : HCC Types H CF Types LOGIC DIAGRAM AND TRUTH TABLE (one of two identical flip–flops) CL∆ – –/ – / – –\ – D R S Q Q 0 0 0 0 1 1 0 0 1 0 X 0 0 Q Q X X 1 0 0 1 X X 0 1 1 0 X X 1 1 1 1 LOGIC 0 = LOW LOGIC 1 = HIGH 2/11 NO CHANGE ∆ = LOW LEVEL X = DON’T CARE N(N) = FF1/FF2 TERMINAL ASSIGNEMENT HCC/HCF4013B STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions) Test Conditions Symbol IL Parameter Quiescent Current VI (V) VO (V) |I O | V D D T L o w* 25 °C T Hig h * (µA) (V) Min. Max. Min. Typ. Max. Min. Max. 0/5 5 1 0.02 1 HCC 0/10 Types 0/15 10 2 0.02 2 60 15 4 0.02 4 120 0/20 20 20 0.04 20 600 0/5 5 4 0.02 4 30 10 8 0.02 8 60 15 16 0.02 16 120 HCF 0/10 Types 0/15 V OH V OL Output High Voltage Output Low Voltage <1 5 4.95 4.95 4.95 0/10 <1 10 9.95 9.95 9.95 0/15 <1 15 14.95 14.95 14.95 5/0 <1 5 0.05 0.05 0.05 <1 10 0.05 0.05 0.05 V IL I OH I OL Input Low Voltage Output Drive Current Output Sink Current CI 15 <1 5 3.5 3.5 0.05 3.5 1/9 <1 10 7 7 7 1.5/13.5 < 1 15 11 4.5/0.5 <1 5 9/1 <1 10 3 3 3 13.5/1.5 < 1 15 4 4 4 11 1.5 1.5 5 – 2 – 1.6 – 3.2 – 1.15 HCC Types 0/10 4.6 5 – 0.64 – 0.51 – 1 – 0.36 9.5 10 – 1.6 – 1.3 – 2.6 – 0.9 0/15 13.5 15 – 4.2 – 3.4 – 6.8 – 2.4 0/ 5 2.5 5 – 1.53 – 1.36 – 3.2 – 1.1 0/ 5 HCF Types 0/10 4.6 5 – 0.52 – 0.44 – 1 – 0.36 9.5 10 – 1.3 – 1.1 – 2.6 – 0.9 0/15 13.5 15 – 3.6 – 3.0 – 6.8 – 2.4 0/5 0.4 5 0.64 0.51 1 0.36 0.5 10 1.6 1.3 2.6 0.9 1.5 15 4.2 3.4 6.8 2.4 0.4 5 0.52 0.44 1 0.36 0.5 10 1.3 1.1 2.6 0.9 1.5 15 3.6 3.0 6.8 2.4 HCC 0/18 Types Input Capacitance Any Input mA ± 0.1 ±10 ± 0.1 ± 1 15 ± 0.3 ±10 –5 ± 0.3 ± 1 5 –5 7.5 V mA 18 Any Input HCF 0/15 Types V 11 1.5 2.5 HCC 0/10 Types 0/15 V 0.05 0/5 HCF 0/10 Types 0/15 Input Leakage Current <1 0.5/4.5 0/5 0/5 I IH , I IL 0.05 µA V 10/0 Input High Voltage Unit 30 0/5 15/0 V IH Value µA pF * TLow= – 55°C for HCC device : – 40°C for HCF device. * THigh= + 125°C for HCC device : + 85°C for HCF device. The Noise Margin for both ”1” and ”0” level is : 1V min. with VDD = 5V, 2V min. with VDD = 10V, 2.5 V min. with VDD = 15V. 3/11 HCC/HFC4013B DYNAMIC ELECTRICAL CHARACTERISTICS (T amb = 25°C, C L = 50pF, R L = 200kΩ, typical temperature coefficient for all V DD = 0.3%/°C values, all input rise and fall time = 20ns) Symbol Parameter t P L H , t P HL Propagation Delay Time (clock to Q or Q outputs) tP LH t P HL Propagation Delay Time (set to Q or reset to Q) Propagation Delay Time (set to Q or reset to Q) t THL , t T L H Transition Time f CL * tW t r, t f ** tW t se t u p * ** Maximum Clock Input Frequency Cock Pulse Width Clock Input Rise or Fall Time Set or Reset Pulse Width Data Setup Time Test Conditions Value V D D (V) Min. Typ. Max. 5 150 300 10 65 130 15 45 90 5 150 300 10 65 130 15 45 90 5 200 400 10 85 170 15 60 120 5 100 200 10 50 100 15 40 80 5 3.5 7 10 8 16 15 12 24 5 140 70 10 60 30 15 40 20 10 4 15 1 90 10 80 40 15 50 25 5 40 20 10 20 10 15 15 7 ns ns ns ns 15 180 ns MHz 5 5 Unit µs ns ns Input tr, tf = 5ns. If more than unit is cascaded in a parallel clocked application, tr should be made less than or equal to the sum of the fixed propagation delay time at 15pF and the transition time of the carry output driving stage for the estimated capacitive load. 4/11 HCC/HCF4013B Typical Output Low (sink) Current Characteristics. Minimum Output Low (sink) Current Characteristics. Typical Output High (source) Current Characteristics. Minimum Output High (source) Current Characteristics. Typical Propagation Delay Time vs. Load Capacitance (CLOCK or SET to Q, CLOCK or RESET to Q). Typical Propagation Delay Time vs. Load Capacitance (SET to Q or RESET to Q). 5/11 HCC/HFC4013B Typical Maximum Clock Frequency vs. Supply Voltage. Typical Power Dissipation Device vs. Frequency. TEST CIRCUITS Quiescent Device Current. Input Leakage Current. 6/11 Noise Immunity. HCC/HCF4013B Plastic DIP14 MECHANICAL DATA mm DIM. MIN. a1 0.51 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 7/11 HCC/HFC4013B Ceramic DIP14/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7.0 0.276 D E 3.3 0.130 0.38 e3 0.015 15.24 0.600 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 1.52 2.54 0.060 0.100 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053C 8/11 HCC/HCF4013B SO14 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 E 5.8 8.75 0.336 6.2 0.228 0.344 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8° (max.) P013G 9/11 HCC/HFC4013B PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 10/11 HCC/HCF4013B Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 11/11