M54HC279 M74HC279 QUAD S - R LATCH . . . . . . . . HIGH SPEED tPD = 12 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 2 µA (MAX.) AT TA = 25 °C HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V TO 6 V PIN AND FUNCTION COMPATIBLE WITH 54/74LS279 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HC279F1R M74HC279M1R M74HC279B1R M74HC279C1R PIN CONNECTIONS (top view) DESCRIPTION The M54/74HC279 is a high speed CMOS QUAD S - R LATCH fabricated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption. All inputs are equipped with protection circuits against static discharge and transient excess voltage. INPUT AND OUTPUT EQUIVALENT CIRCUIT NC = No Internal Connection March 1993 1/10 M54/M74HC279 PIN DESCRIPTION PIN No SYMBOL 1, 5, 10. 14 1R to 4R 2, 3, 6, 11, 1S1, 1S2, 2S, 12, 15 3S1, 3S2, 4S 4, 7, 9, 13 1Q to 4Q 8 GND 16 V CC IEC LOGIC SYMBOL NAME AND FUNCTION Reset Inputs (Active LOW) Set Inputs (Active LOW) Outputs Ground (0V) Positive Supply Voltage TRUTH TABLE S # H L H L R H H L L Q Q0 H L H NOTE: Q0 = THE LEVEL OF Q BEFORE THE INDICRTED INPUT CONDITION WAS ESTABLISHED. # FOR LATCHES WITH DOUBLE S INPUT: H = BOTH S INPUTS HIGH L = ONE OF BOTH INPUTS LOW LOGIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit VCC VI Supply Voltage DC Input Voltage -0.5 to +7 -0.5 to VCC + 0.5 V V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK IOK DC Input Diode Current DC Output Diode Current ± 20 ± 20 mA mA IO DC Output Source Sink Current Per Output Pin ± 25 mA ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg TL Storage Temperature Lead Temperature (10 sec) ± 50 mA 500 (*) mW -65 to +150 300 o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC 2/10 M54/M74HC279 RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC VI Supply Voltage Input Voltage VO Output Voltage Top Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time tr, tf Value Unit 2 to 6 0 to VCC V V 0 to VCC V o -55 to +125 -40 to +85 0 to 1000 VCC = 2 V VCC = 4.5 V 0 to 500 VCC = 6 V 0 to 400 C C ns o DC SPECIFICATIONS Test Conditions Symbol VIH V IL V OH VOL Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage VCC (V) 2.0 Min. 1.5 4.5 3.15 6.0 2.0 4.2 6.0 2.0 ICC Quiescent Supply Current Max. -40 to 85 oC -55 to 125 oC 74HC 54HC Min. 1.5 Max. 3.15 Min. 1.5 4.2 4.2 0.5 0.5 1.35 1.35 1.35 1.8 2.0 1.9 1.9 4.5 4.4 4.4 6.0 4.5 5.9 4.18 6.0 4.31 5.9 4.13 5.9 4.10 6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60 6.0 6.0 V 1.8 1.9 4.4 2.0 4.5 V 0.5 1.8 Unit Max. 3.15 VI = IO=-20 µA VIH or V IL IO=-4.0 mA 4.5 4.5 6.0 Input Leakage Current Typ. 4.5 6.0 II Value TA = 25 oC 54HC and 74HC V 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.17 0.18 0.26 0.26 0.33 0.33 0.40 0.40 VI = VCC or GND ±0.1 ±1 ±1 µA VI = VCC or GND 2 20 40 µA VI = IO= 20 µA VIH or V IL IO= 4.0 mA IO= 5.2 mA V 3/10 M54/M74HC279 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions o TA = 25 C 54HC and 74HC Value -40 to 85 oC -55 to 125 oC 74HC 54HC Symbol Parameter VCC (V) tTLH tTHL Output Transition Time 2.0 4.5 Typ. 30 8 Max. 75 15 tPLH tPHL Propagation Delay Time (S1, S2 - Q) 6.0 2.0 4.5 6.0 7 45 15 13 13 130 26 22 16 165 33 28 19 195 39 33 tPLH tPHL Propagation Delay Time (S - Q) tPHL Propagation Delay Time (R - Q) 2.0 4.5 6.0 2.0 4.5 38 12 10 42 14 100 20 17 120 24 125 25 21 150 30 150 30 26 180 36 6.0 12 5 18 20 10 26 10 31 10 CIN CPD (*) Min. Input Capacitance Power Dissipation Capacitance Min. Max. 95 19 Min. Max. 110 22 Unit ns ns ns ns pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC SWITCHING CHARACTERISTICS TEST WAVEFORM 4/10 M54/M74HC279 TEST CIRCUIT ICC (Opr.) 5/10 M54/M74HC279 Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 6/10 M54/M74HC279 Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 7/10 M54/M74HC279 SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 8/10 M54/M74HC279 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 9/10 M54/M74HC279 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 10/10