TSM100 SINGLE OPERATIONAL AMPLIFIER AND SINGLE COMPARATOR OPERATIONAL AMPLIFIER ■ LOW INPUT OFFSET VOLTAGE : 0.5mV typ. ■ MEDIUM BANDWIDTH (unity gain) : 0.9MHz ■ LARGE OUTPUT VOLTAGE SWING : 0V to (VCC - 1.5V) ■ INPUT COMMON MODE VOLTAGE RANGE INCLUDES GROUND ■ WIDE POWER SUPPLY RANGE : 5 to 30V ±2.5 TO ±15V ■ ESD PROTECTION : 2kV D SO8 (Plastic Micropackage) COMPARATOR (OPEN COLLECTOR) ■ INPUT COMMON MODE VOLTAGE RANGE INCLUDES GROUND ■ LOW OUTPUT SATURATION VOLTAGE : 250mV @ Io = 4mA PIN CONNECTIONS (top view) DESCRIPTION 8 : Vcc Amp Input - : 2 7 : Comp Output ORDER CODE Part Number TSM100I + Amp Output : 1 - The TSM100 is a monolithic IC that includes one independent op-amp and one independent comparator. This device is offering space and cost saving in many applications like power supply management or data acquisition systems. Amp Input + : 3 Temperature Range -40°C, +105°C D Ground : 4 - 6 : Comp Input + Package 5 : Comp Input + • D = Small Outline Package (SO) - also available in Tape & Reel (DT) July 2001 1/5 TSM100 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit VCC Supply Voltage 32 V Vid Differential Input Voltage 32 V Vi Input Voltage -03. to +32 V Operating Free-air Temperature Range Toper -40 to +105 °C Tj Maximum Junction Temperature 150 °C Tl Maximum Lead Temperature (10 seconds maximum) 260 °C Thermal Resistance Junction to Ambient 175 °C/W Rthja ELECTRICAL CHARACTERISTICS Symbol ICC 2/5 Parameter Total Supply Current Vcc+ = 5V, no load Vcc+ = 30V, no load Min. Typ. Max. 0.9 1.4 1.8 Unit mA TSM100 OPERATIONAL AMPLIFIER VCC+ = +5V, VCC = Ground, V o = 1.4V,T amb = 25°C (unless otherwise specified) Symbol Vio DVio Parameter Min. Typ. Max. 0.5 3 4 Unit mV Input Offset Voltage Tamb = 25°C Tmin. ≤ Tamb ≤ Tmax. µV/°C Input Offset Voltage Drift 7 Iio Input Offset Current 2 30 nA Iib Input Bias Current 20 150 nA Avd V/mV Large Signal Voltage Gain VCC = 15V, RL = 2k, Vo = 1.4V to 11.4V 50 100 Supply Voltage Rejection Ratio VCC = 5V to 30V 65 100 Input Common Mode Voltage Range VCC = +30V - see note 1) 0 CMR Common Mode Rejection Ratio 65 Isource Output Current Source VCC = +15V, Vo = 2V, Vid = +1V SVR Vicm Io Isink VOH VOL SR GBP THD en dB High Level Output Voltage VCC+ = 30V Tamb = 25°C, RL = 2k Tamb = 25°C, RL = 10k 85 20 mA 10 12 60 20 50 mA µA V 26 27 27 28 mV 5 15 V/µs Slew Rate at Unity Gain Vi = 0.5 to 3V, VCC = 15V RL = 2k, CL = 100pF, unity gain 0.2 0.4 Gain Bandwidth Product VCC = 30V,RL = 2k, CL = 100pF f = 100kHz, Vin = 10mV 0.5 0.9 Equivalent Input Noise Voltage f = 1kHz, Rs = 100Ω Vcc = 30V dB 40 40 Low Level Output Voltage RL = 10k Total Harmonic Distortion f = 1kHz AV = 20dB,RL = 2k, VCC = 30V CL = 100pF, Vo = 2Vpp V mA Short Circuit to Ground VCC = +15V Output Current Sink Vid = -1V, VCC = +15V, Vo = 2V VCC = +15V, Vo = 0.2V (VCC+) -1.5 MHz % 0.015 nV/√Hz 40 1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V. But both inputs can go to Vcc+ +0.3V without damage. 3/5 TSM100 COMPARATOR VCC+ = +5V, VCC = Ground,Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit 1 5 mV Vio Input Offset Voltage Tamb = 25°C Iio Input Offset Current 5 50 nA Iib Input Bias Current 25 250 nA Large Signal Voltage Gain VCC = 15V, RL = 15k, Vo = 1V to 11V 200 Avd V/mV (VCC+) -1.5 Input Common Mode Voltage Range 1) 0 Isink Output Sink Current Vid = -1V, Vo = 1.5V 6 VOL Low Level Output Voltage Vid = -1V, Isink = 4mA 250 High Level Output Current Vid = 1V, Vcc = Vo = 30V 0.1 Response Time RL = 5.1k to VCC+ 2) 1.3 Large Signal Response Time Vi = TTL, Vref = +1.4V, RL = 5.1k to VCC+ 300 Vicm IOH tre trel 16 V mA mV 400 nA µs ns 1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V. But either of both inputs can go to 36V without damage. 2. The response time is specified for a 100mV input step with 5mV overdrive. For larger overdrive signals, 300ns can be obtained 4/5 TSM100 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) Millimeters Inches Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S Typ. Max. 0.65 0.35 0.19 0.25 1.75 0.25 1.65 0.85 0.48 0.25 0.5 4.8 5.8 5.0 6.2 0.1 Min. Typ. Max. 0.026 0.014 0.007 0.010 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 45° (typ.) 1.27 3.81 3.8 0.4 0.050 0.150 4.0 1.27 0.6 0.150 0.016 0.157 0.050 0.024 8° (max.) Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 5/5