STMICROELECTRONICS VV6501C001

STV0681
®
DUAL-MODE DIGITAL CAMERA CO-PROCESSOR
DESCRIPTION
●
Quick Power Down (by holding Mode Button).
STMicroelectronics Imaging Division has produced
the camera co-processor STV0681 which, used
with CIF/VGA sensors as part of a low cost dualmode camera chipset, allows a new line of low cost
cameras or toy products to be brought to the
market. STV0681 is a mask ROM version of
STV0680B, programmed with v3.00 Firmware.
●
“Delete Last” Function
FEATURES
ST have maintained the standard features already
available in the successful STV068B chipset,
including:
Audio Record and Playback
The enhanced features included in STV0681 allow
audio memos to be recorded at a sampling rate of
11kHz, by adding a microphone and comparator
chip, and by utilizing the pre-amplifier included in
CIF/VGA sensors such as VV6411 and VV6501
respectively.
These sounds can be uploaded to the PC over USB
or RS232, and played back using a Software
application developed by the OEM using the SDK.
Demonstration PC software with source code is
available with the Evaluation Kit (EVK). With
suitable OEM software, the camera could even be
used to record comments about pictures or video
clips in a “dictaphone” fashion, with the audio
commentary played back when viewing the
pictures/video.
●
Support for VV6411 (CIF) and VV6501 (VGA)
CMOS imaging sensors.
●
Support for SDRAM sizes 16MBit (up to 20
CIF images) or 64Mbit (up to 80 CIF or 26
VGA images).
●
Low resolution “economy” mode allows for
more images to be stored.
●
High frame rate web cam (tethered video)
over USB.
●
Audio record/playback and “Delete Last”
function
●
Custom sounds playback (e.g. “Talking” or
“Musical” camera)
●
Support for an OEM Flashgun module
●
Automatic anti-flicker exposure control.
●
Image up load over RS232 or USB.
Evaluation Kit and Reference Design
●
Driver support for Win98/Win2k/WinME and
MacOS 8.6/9.0/9.1.
●
Continuous capture while untethered (except
when Flashgun enabled) and downloading to
AVI file format
Evaluation kits are available for STV0681 features.
Precise design guidelines are available from ST as
a reference design manual (see Chapter 10).
●
Power-saving “stand-by” mode which
maintains memory contents.
●
Simple user interface including 2 buttons,
status LCD display, and buzzer.
●
Evaluation Kit (EVK) available.
●
Software Development Kit (SDK) allows OEM
PC Software applications to be written.
March 2003
Recorded audio sounds can also be played back on
the camera, with the addition of an amplifier chip
and speaker or headphone socket.
By auto-detecting hardware, STV0681 will only
enable these additional functions if audio hardware
is fitted. Actual hardware implementation is the
subject of a separate STV0681 Reference design
(see Chapter 10).
Note:
ADCS 7283313C
Simultaneous audio record and
continuous video capture is not possible.
1/44
STV0681
Table of Contents
Chapter 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.1
Digital camera chipset .......................................................................................................... 5
1.2
Key system features ............................................................................................................. 6
Chapter 2
Detailed Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.1
Sensor type and image formats ........................................................................................... 9
2.2
User interface ..................................................................................................................... 10
2.3
Battery level detect and USB auto-switch .......................................................................... 12
2.4
Audio record and playback ................................................................................................. 12
2.5
PC interface options and software support ........................................................................ 13
2.6
Anti-flicker exposure and gain control ................................................................................ 14
Chapter 3
Camera Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3.1
Modes available ................................................................................................................. 15
3.2
Description of modes ......................................................................................................... 16
Chapter 4
STV0681 Hardware Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
4.1
Sensor interface ................................................................................................................. 18
4.2
Memory interface ............................................................................................................... 18
4.3
USB interface ..................................................................................................................... 21
4.4
UART module for RS232 interface ..................................................................................... 22
4.5
Power management and battery type ................................................................................ 23
4.6
Quartz crystal ..................................................................................................................... 24
4.7
Numeric LCD interface ....................................................................................................... 24
4.8
Switches and LED’s ........................................................................................................... 25
4.9
Flashgun hardware interface .............................................................................................. 26
4.10
IR filter ................................................................................................................................ 26
Chapter 5
Customising the STV0681 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
2/44
5.1
External EEPROM ............................................................................................................. 27
5.2
EEPROM data format ........................................................................................................ 28
5.3
Programming the EEPROM ............................................................................................... 28
ADCS 7283313C
STV0681
Chapter 6
Software support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
6.1
General features ................................................................................................................ 29
6.2
Software installation ........................................................................................................... 30
Chapter 7
Detailed Chipset Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
7.1
Typical camera specifications ............................................................................................ 31
7.2
Absolute maximum ratings ................................................................................................. 31
7.3
STV0681 specifications ...................................................................................................... 32
7.4
USB specifications ............................................................................................................. 32
7.5
DC characteristics .............................................................................................................. 33
7.6
PLL characteristics ............................................................................................................. 33
7.7
Crystal tolerance ................................................................................................................ 33
7.8
Typical current consumption of complete camera .............................................................. 34
Chapter 8
STV0681 pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
8.1
STV0681 pinout ................................................................................................................. 35
8.2
STV0681 pin description .................................................................................................... 36
Chapter 9
STV0681 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Chapter 10
Evaluation Kit (EVK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
10.1
Ordering details .................................................................................................................. 42
10.2
Technical support ............................................................................................................... 43
ADCS 7283313C
3/44
STV0681
Document Revision History
Revision
Draft
Date
Comments
A
1.0
May 2001
Initial release (product preview)
B
4.0
April 2002
Document status updated to datasheet.
Major changes: removed references of VV6410 and VV6444
sensors
C
4.1
November
2002
Removed all salestypes for imaging sensors:
removed section 6.1
addition of chapter 5 - Customizing the STV0681
Replacement of section 6.1 - General features (in Chapter 6 Software support)
4/44
ADCS 7283313C
STV0681
1
Introduction
1.1
Digital camera chipset
1.1.1
General
Introduction
This document describes the features and functionality of a CMOS chipset, comprising an
STMicroelectronics (ST) CIF or VGA resolution sensor and an STV0681 companion processor, as
well as outlining what peripheral components are required/supported in order to complete a camera
using the chipset. Such a camera is particularly suited to dual-mode digital stills or toy applications.
1.1.2
Stills capture and image upload
In stills mode, the camera stores raw image data in memory. The camera features no colour
processing, ensuring its simplicity and low cost. Subsequent upload of raw data to a PC or
Macintosh for processing is done through an RS232 or USB interface, through demo software, a
TWAIN driver, or OEM custom application. The license to use the colour algorithm (embedded in
the PC or Mac driver software) is included in the price of the chipset.
1.1.3
Webcam Video over USB
A video option is provided, when tethered through USB. It allows for Video for Microsoft Windows
applications, and ‘video clips’ to be recorded while untethered by continuously capturing images in
‘continuous’ mode. Images are then downloaded to the PC for playback, using software to create an
AVI file.
1.1.4
Audio features
The STV0681 allows audio memos to be recorded at a sampling rate of 11kHz. These sounds can
be uploaded to the PC over USB or RS232 and played on the PC, or they can be replayed on the
camera.
With audio playback hardware fitted to the camera, it is possible to download a set of up to 20.WAV
file “sound bites”, to store in SDRAM, each of which can be linked to a particular camera function.
This allows for camera “Theme Music”, custom sounds such as an imitation shutter “Click-Whirr”, or
for certain functions to “talk” to the user, e.g. “Nice picture!”.
This has limitless possibilities for OEM language customizing or licensed character cameras.
Downloading sounds is possible with the use of an OEM application developed using the SDK, and
a demonstration PC application with source code is available with the EVK. Sounds are stored in
SDRAM and will therefore reduce the number of images/amount of audio which can be stored,
STV0681 calculates the remaining memory and displays the number of images left. Sounds can
only be stored when untethered while battery power is maintained.
1.1.5
Flashgun support
The addition of an OEM flashgun module increases the camera capabilities and improves low light
image quality. STV0681 flashgun support includes modified exposure control, an enable input and a
correctly timed trigger output. Although it remains the responsibility of the OEM to source a suitable
Flashgun module, advice on hardware interfacing, flash charge sensing and required flashgun
energy are given in a separate Flashgun Application Note (AN1312), please contact ST for details.
ADCS 7283313C
5/44
Introduction
1.1.6
STV0681
“Delete Last” function
An additional user interface function is available in STV0681 with either audio record or playback
hardware fitted. With these, the user can delete the last image or continuous clip to be captured, or
the last audio memo to be recorded. The standard “Clear all” (“CL”) function remains, whether or not
audio hardware is fitted.
1.1.7
Backward compatibility with STV0680B
STV0681 is electrically and functionally compatible with cameras designed for STV0680B, and uses
the same PC/Mac drivers, however the change of device pinout means that some PCB re-design
will be required.
Precise design guidelines are available from ST as a reference design (see Chapter 10). A software
development kit (SDK) for PC is available from ST to interface to the camera and provide the basis
to develop a custom software application for stills and/or video. It includes colour processing
software.
Figure 1: Typical camera system block diagram
LED
Audio
Speaker
Amplifier
Push
Buttons:
“Shutter
/Record”
Flashgun
Enable/Trigger
2 x 7 seg. LCD
“Mode”
CMOS Sensor
OEM Flashgun
Module
VV6411 (CIF)
VV6501 (VGA)
Microphone
Comparator
GPIO
Enable/Trigger
Audio
Pre-Amp
Audio DAC
Sensor data
Sensor clock
Sensor
I/F
Piezo
Buzzer
PWM
LCD memory
Driver
I/F
RS232
I/F
STV0681
Image Array
Subject
Lens +
IR Filter
USB
I/F
Detect Low
Battery
12MHz XTAL
VReg
16MBit or 64MBit
SDRAM
Transceiver
Circuit (Discretes)
Power
Management
Circuit (Discretes)
RS232 interface
to PC
USB interface
to PC
4.5 - 6v Battery e.g.
3-4 x AA, AAA, etc.
3v3 supply
4-5v (Nominal) supply from Battery or USB
1.2
Key system features
The key features of a typical camera based on the STV0681 chipset are listed here below.
1.2.1
Image features
●
Support for CIF resolution sensor - 352 x 288 pixels
●
Support for VGA resolution sensor - 640 x 480 pixels
●
80 picture storage capacity possible for CIF, with 64MB memory
●
26 picture storage capacity for VGA, with 64MBit memory
●
A greater number of images can be stored when ‘Low’ resolution mode is enabled (e.g. 80 QCIF
images with 16Mbit memory, 107 QVGA images with 64Mbit memory). See Table 1.
●
Automatic anti-flicker exposure and gain control
●
Support for flashgun.
6/44
ADCS 7283313C
STV0681
1.2.2
Introduction
User features on camera
●
Self-timer mode allows a picture to be captured after several seconds.
●
Twin 7 segment LCD panel supported - showing number of pictures left, and modes.
●
Picture counter helps the user to know how much memory is left.
●
Un-tethered ‘Continuous’ mode allows capture of image sequences for storage in memory and
subsequent download to PC.
●
Piezo buzzer indicates a number of useful events to the user, e.g. whether enough light is present for
picture capture, etc.
●
LED indicator .
●
“Clear all” function clears camera.
●
“Low Resolution” mode increases number of images which can be captured by reducing image
resolution.
●
Audio Record function (if audio record hardware detected) allows sounds to be recorded.
●
Audio Playback function (if audio playback hardware fitted) allows sounds which have been recorded
to be played back.
●
“Delete last” function allows user to delete audio memos, pictures or continuous clips, deletion must
be carried out “most reset first”.
●
Camera can be configured by the user to play custom sounds at certain functions, using a PC
application.
●
“Go to sleep” function, whereby the camera can be put into standby mode while untethered.
1.2.3
User features on PC software
PC software allows a number of features such as fast download of thumbnail images for picture
selection, and automatic detection and correction of sensor defects. The driver compatibility
includes:
●
TWAIN driver to suit all TWAIN compatible imaging applications
●
Video for Microsoft Windows PC driver for tethered video mode (through USB), available at all
resolutions, with fastest framerates at QCIF resolution
●
AVI video file creation from image sequences captured in ‘continuous’ mode
●
Quicktime Video driver and Adobe Photoshop stills plug-in for Mac
Custom OEM PC software can be developed by using the SDK (for SDK availability, contact ST), to
upload thumbnails/still images or ‘continuous’ images, e.g. for AVI file creation.
The SDK (version 2.90 or later) allows:
●
the OEM to write a custom application and upload sound memos based on the example LCDC demo
software.
●
the OEM to write a custom application and download custom sounds to the camera based on the
example CustomSound software.
1.2.4
Power management features and USB compliance
●
Retention of pictures, recorded sounds and downloaded custom sounds with extremely low power
operation. The camera seems to be “switched off”.
●
Auto power-off after 30 seconds of non usage.
●
Operates from 4.5-6V battery, although system voltage is 5V or 3.3V, dependant on sensor.
●
Low battery detection.
ADCS 7283313C
7/44
Introduction
STV0681
●
Dependant on hardware configuration, switch-over to USB power supply is supported and the device
can operate with low batteries or without batteries when connected to USB.
●
Full USB compliance requirements are listed in the USB specification. However, in a camera designed
using this chipset, the following must at least be included: (a) an SDRAM with sufficiently low selfrefresh current, (b) USB inrush protection circuitry to maintain sufficient supply voltage to the 5V
sensor. See Section 7 for further details.
1.2.5
General features
●
High speed picture/sounds upload to PC/Mac over USB
●
ST colour processing algorithms included under license (as part of drivers/SDK)
●
USB or RS232 serial interface options, and VfW / TWAIN driver support.
8/44
ADCS 7283313C
STV0681
Detailed Features
2
Detailed Features
2.1
Sensor type and image formats
The sensor type is auto-detected by STV0681, the correct sensor timing is enabled and the correct
image resolutions are enabled, as shown in Table 1.
For stills photography, ‘High’ or ‘Low’ resolution mode can be selected, to give CIF or QCIF pictures
from a CIF sensor, and VGA or QVGA from a VGA sensor (see Table 1). Reduced resolution allows
for storage of more images. Images captured in both ‘High’ and ‘Low’ resolution can be stored in
camera memory at the same time. Therefore there is no need to clear images stored in memory
prior to changing image resolution.
Where USB is connected, the host PC software (through a Video for Microsoft Windows driver)
can activate tethered video mode, regardless of the user inputs to the camera buttons. In this case,
the image resolution is controlled by the PC driver.
Note:
When tethered VfW video (PC) or Quicktime driver (Mac) is activated, all images or recorded
sounds or video clips are deleted from the camera SDRAM. A software solution is available
(“Camera control”, as part of the SDK for PC, and “Plug’n Save” for Mac) which can monitor whether
a camera is connected and warns the user if activating the VfW driver causes SDRAM contents to
be deleted.
Table 1: Image modes supported
Sensor
Image Size
CIF 352 x 288
Max. no. of
images
Resolution
stored in
Final Image Size
mode
16MBit
memory
(Note 2)
High
CIF 352 x 288
20
Low
QCIF 176 x 144
80
Approximate
VfW framerate
(Note 1)
80
15 frames/sec.
322
22.5 frames/sec.
(see Note 3)
(Subsampled)
VGA 640 x 480
Max. no. of
images
stored in
64MBit
memory
(Note 2)
High
VGA 640 x 480
(6)
Low
QVGA 320 x 240
(26)
(Subsampled)
26
2 frames/sec.
107
12 frames/sec.
(see Note 3)
Note: 1 VfW framerate is dependent on PC performance and USB bus loading
2 The number of images which can be stored is reduced if Audio sounds have been recorded on the
camera or if custom sounds have been downloaded from the PC to the camera. The reduction of
capacity depends on the length of audio clip, but a rough guide is that if 1 CIF image uses the same
amount of SDRAM as 10sec of audio, and one VGA image uses the same amount of SDRAM as 30
sec. of audio.
3 A CIF camera with STV0681 and 64Mbit SDRAM can store up to 320 images by using QCIF mode.
When more than 99 images are available, the LCD display remains at 99. When the number of
available images is inferior to 99, the LCD display shows the number of available images like in all
other modes.
ADCS 7283313C
9/44
Detailed Features
2.1.1
STV0681
IR filter
For IR filter design, the best choice filter follows the GS0034 dielectric stack filter specification
available from STMicroelectronics. An alternative, although not optimal filter, would be Schott
S8612 doped glass also sold as CM500.
2.2
User interface
The user interface supported by STV0681 comprises of user controls, buzzer sounds or customized
sounds and visual displays.
2.2.1
Push buttons
The following are the functions which are supported by the chipset. These functions are achievable
with no more than 2 push buttons.
1
Mode button (wake-up/switch between modes)
This button allows the user (1.1) to wake the camera up from standby mode when the camera
is to be used for taking pictures, or (1.2) to switch between modes of operation shown in
Chapter 3.
2
Shutter button (shutter/confirm action)
This button allows the user to take a picture or confirm an action, as shown in Chapter 3
The modes of operation are described in Chapter 3.
It may also be desirable to include an on-off slider switch. The advantages and disadvantages as
well as its exact function are discussed in the reference design available from STMicroelectronics.
When a flashgun module is included in the camera, it is necessary to include a flash on/flash off
push button or slider switch depending on the exact flashgun module design. Possible
implementations are discussed in a separate application note AN1312 available from
STMicroelectronics.
2.2.2
LED indicator
The LED indicator displays the camera status when not in Standby/PC suspend mode.
2.2.3
Picture counter using 2 x 7 segment display
STV0681 stores a picture counter value indicating how many images can still be captured.
STV0681 supports a 2x7 segment LCD panel. In ‘Snapshot’ mode and continuous capture mode,
this LCD panel displays the number of pictures still available. This is useful to identify when the user
is approaching the maximum number of images which can be stored (see Table 1). The user can
clear the images stored in memory and continue taking pictures. In other modes, this LCD panel
displays a 2-character code that helps the user to navigate around the modes.
Note:
A CIF camera with STV0681 and 64Mbit SDRAM can store up to 320 images by using QCIF mode.
When more than 99 images are still available, the LCD display remains at 99. When the number of
available images is inferior to 99, the LCD display shows how many images are available like in all
other modes.
For suitable numeric LCD panel types, see Section 4.7.
10/44
ADCS 7283313C
STV0681
2.2.4
Detailed Features
Piezo buzzer
An on-chip pulse width modulator (PWM) generates buzzer sounds to signal certain events. The
distinctive sounds are characteristic of the type of events indicated by the buzzer, as described here
below.
2.2.5
1
Camera has been ‘Woken up’ from standby mode (either by the user pressing a button, by reconnecting the power source, or by connecting a USB/RS232 connection).
2
Camera has ‘gone to sleep’ that is moved into standby mode. Pictures are retained in memory.
3
Picture was taken successfully once the user had pressed the capture button.
4
Picture has NOT been taken when the user pressed the capture button because of insufficient
light, or because the exposure control was not ready following a rapid change of lighting in the
scene.
5
Picture has NOT been taken when the user pressed the capture button because the picture
counter had reached the maximum number of images. The user has the chance to reset the
counter if desired.
6
End of continuous capture in un-tethered ‘Continuous’ mode due to full memory.
7
Self-timer activated, count down has started.
Custom sounds
A camera which includes STV0681 and audio playback hardware can have a set of custom sounds
downloaded from a PC application. A different sound can be associated with each of the following
functions:
Table 2: List of custom sound functions
Power On
Power Off
Good picture
Bad picture
(Normally due to insufficient light)
Memory full
Self timer #1
Self timer #2
Low resolution
High resolution
Picture delete
Sound delete
Continuous clip delete
Clear memory
Confirm action
Low power
Flashgun ON
Flashgun OFF
Flashgun Trigger
ADCS 7283313C
11/44
Detailed Features
STV0681
Table 2: List of custom sound functions
Frequency 50kHz
Frequency 60kHz
Note: 1 When a sound is associated to a given function, and it is stored in SDRAM, the piezo buzzer does
not give any beeps for that function. Not all functions need to have custom sounds associated with
them, this is the choice of the user or OEM.
2 A demonstration PC application “CustomSounds” is available from ST, however this is not intended
for end-users. Source code is available which allows the OEM to build their own PC application
using the SDK.
2.3
Battery level detect and USB auto-switch
An on-chip battery level detector on STV0681 detects when the battery voltage falls below a
threshold. The chosen threshold level is determined by a resistor value, as shown in Chapter 7.
Where no USB has been detected, the LCD display flashes, indicating that the battery is low. When
a USB connection has been detected, the LCD display does not flash.
Note:
It may be a requirement of certain USB compliance tests that such additional hardware is included
in the camera design, in order to enable the camera to switch to supply from USB and hence report
back to the PC while connected to the USB bus without a battery.
2.4
Audio record and playback
2.4.1
Record
A camera including the STV0681 with a microphone, a comparator and other periphery (also using
the sensor pre-amplifier) can record sounds stored like images. STV0681 auto-detects the
presence of audio record hardware and includes audio record and “delete last” functions into the
user interface. The audio sample rate is 11.025 kHz, the signal is digitized using a successive
approximation A-D converter with 8 bits resolution. The SDRAM stores 1 second of audio recording
per 11 kByte of memory.
2.4.2
Playback
A camera including the STV0681 with an amplifier, a speaker/headphone socket and other
periphery can playback sounds either recorded on the camera or downloaded from the PC.
The quality of audio playback is largely dependant on the type of speaker used, and on the correct
mounting of the speaker in the camera plastics.
12/44
ADCS 7283313C
STV0681
2.5
Detailed Features
PC interface options and software support
USB interface (full speed 12Mbit per second maximum) and RS232 interface (115.2kbaud) are
supported by the chipset, with driver software available from STMicroelectronics for both. The
interface type is auto-detected by the chipset. PC software can be one of the following:
2.5.1
1
Simple image upload demonstration software supplied by ST, allowing uploading of stills or
‘continuous’ images. This software should not be supplied as an end-user product.
2
TWAIN driver to suit all TWAIN compatible imaging applications,
3
Video for Microsoft Windows driver for tethered video mode (USB only),
4
Custom end-user software developed by OEM using SDK (for SDK availability, contact ST).
The SDK is supplied by ST as a 32-bit DLL format, running on Microsoft Windows 98, and
accessed through a documented software interface. This provides the basis for developing a
custom software application for uploading stills and/or video.
USB
Complete images (displayed as either thumbnails or in full resolution), or the entire SDRAM
contents (e.g. for uploading continuously captured image sequences, recorded using ‘Continuous
Capture’ mode) can be downloaded through USB, and USB connection also allows for tethered
video mode to be activated by the USB driver.
Thumbnail image download is extremely fast for the entire memory contents in the camera. Once a
picture is selected for download, full image download takes approximately 0.15 second per image
for a CIF image (0.6 second for a VGA image), plus post processing time per image.
For USB interface details, see Section 4.3.
Note:
Actual USB download and post processing time also depends on PC performance and USB bus
loading
2.5.2
RS232
Thumbnails of images, complete stored images, or the entire SDRAM contents can be downloaded
through RS232, but tethered video is not supported.
Once a picture is selected for download, full image download takes approximately 10 seconds per
image for a CIF image (around 30 seconds for a VGA image), plus post processing time per image
(of the order of 1 second approximately).
For RS232 interface details, see Section 4.4.
Note:
Actual post processing time after RS232 download also depends on PC performance
ADCS 7283313C
13/44
Detailed Features
STV0681
2.6
Anti-flicker exposure and gain control
2.6.1
General
The chipset operates automatic exposure and gain control for either 50Hz or 60Hz mains-driven
indoor lighting, using the same 12MHz crystal. This improves picture quality by selecting a set of
exposure values which minimize ‘flicker’ effects. Detection of the mains frequency is dependant on
the status of the GPIO3 pin, which can be achieved by population of a PCB link at a late stage in
production, once the country of destination is known, without the need to change the crystal
frequency.
The auto exposure and gain algorithm is always enabled during Snapshot’/self-timer/continuous
mode. When the shutter button is pressed in ‘Snapshot’ mode, the chipset captures an image if the
exposure and gain values are suitable for the current scene. If the light has suddenly changed, the
camera may emit an audible tone to indicate that more time is required to reach the correct
exposure target. In ‘Snapshot’ mode the chipset only captures the image data if sufficient light is
present in the image. In continuous capture mode, the chipset captures images regardless of
whether enough light is present.
The exposure control algorithm in STV0681 chooses exposure values which minimize “flicker”
effects from occurring under fluorescent lighting. STV0681 can only prevent flicker in lighting
powered by 50Hz or 60Hz electricity supply, but automatic detection of the flicker frequency is not
possible. Hence choosing the correct anti-flicker setting is important, in order to prevent dark stripes
from appearing across the image, and this selection must be done in hardware.
Figure 2: Illustration of flicker problem
Flicker setting not correct
2.6.2
Flicker setting correct
Flashgun exposure
When the STV0681 and a flashgun module are included in the camera, and the flashgun enable
signal is high, the exposure mode operates in a different manner. The CMOS sensor progressive
scan readout requires that the sensor is set to maximum exposure so that all lines are exposed.
The flashgun operates during a few 100 µs in order to correctly expose all sensor lines, (contact ST
for more precise details), therefore the flashgun module design should have reached maximum light
output within this period after the falling edge of the flash trigger output from STV0681.
Possible flashgun implementations, regarding hardware interface, charge sensing, and flash energy
required are discussed in a separate application note AN1312 available from STMicroelectronics.
14/44
ADCS 7283313C
STV0681
3
Camera Modes of Operation
Camera Modes of Operation
This section refers to the two switches as discussed in section Section 2.2.1
●
“Mode”: connects GPIO0 pin of STV0681 to GND when pressed
●
“Shutter”: connects GPIO1 pin of STV0681 to GND when pressed
Pressing the mode switch repeatedly cycles through a series of modes as displayed on the LCD.
When a given mode is displayed it may be selected by pressing the shutter button. If an option is not
selected within 5 seconds, the display reverts to showing the number of available pictures.
3.1
Modes available
Figure 3: STV0681 modes (CIF camera with 16Mbit SDRAM assumed)
Press Mode button
Normal: 20 / 80
After 30sec of inactivity
Standby mode (untethered)
Audio Record: Ar
Notes:
Audio Playback: AP
1. Audio Record only available if audio hardware is fitted
2. Audio Playback only available once an audio clip has been recorded
Delete Last: dA / dP / dC
Continuous Capture: Ct
Self-Timer: St
3. Delete Last displays (only available if audio hardware fitted)
dA - if the last object is an audio clip
dP - if the last object is a picture
dC - if the last object is a continuous capture clip
The mode is inhibited if the camera is empty.
4. Continuous Capture mode is inhibited when the flashgun is enabled
(SW6 down)
Clear All: CL
Resolution: Hr / Lr
ADCS 7283313C
15/44
Camera Modes of Operation
STV0681
3.2
Description of modes
3.2.1
Standby mode (untethered) and Wake-up
On power-up, or wake-up from untethered standby mode, (i.e. by pressing the Mode button), the
camera beeps twice. The LCD briefly indicates the camera resolution either ‘Hr.’ for high resolution
(80 CIF or 26 VGA images - using 64Mbit memory) or ‘Lr’ for low resolution (322 QCIF or 107 VGA
images - using 64Mbit memory) and then displays the number of pictures which may be taken.
Please note that in low resolution mode, although there can be up to 322 images available, the LCD
counter only goes up to 99, it reports 99 until there are less than 99 images left.
The camera goes back to standby mode after 30 seconds of inactivity, LED1 turns off and the LCD
goes blank. This is also achieved by pressing the mode switch during more than 2 seconds.
3.2.2
Normal mode
Press the shutter button to take a picture. The camera beeps. A high pitched beep indicates that the
picture was taken successfully and the counter decrements (if there are less than 99 images left to
take). A low beep indicates insufficient light to take a picture. A series of beeps indicates that the
camera is full.
Stored pictures can be uploaded to a PC at any time, whether or not the camera is full. Plugging the
USB connector into the camera causes it to reset and issues a double beep but all stored pictures
remain. When the USB connector is unplugged the camera goes to sleep. When connected to the
PC, the camera can still be used in the normal way.
Note:
When flashgun is enabled, the camera always takes a picture, with or without sufficient light.
3.2.3
Audio record - Ar
This mode is available with audio record hardware fitted.
Pressing the shutter button within 5 seconds causes the camera to start recording for as long as the
shutter button is pressed down. If the shutter button is not pressed within 5 seconds, the camera
reverts to normal picture taking mode. Whilst recording, the LCD display flashes ‘Ar’. If the
recording stops because the memory is full, the ‘memory full’ audio tone is sounded and the display
stops flashing and displays ‘00’. The audio data is digitized and stored in SDRAM.
3.2.4
Audio Playback - AP
This mode is available with audio playback hardware fitted.
Pressing the shutter button within 5 seconds causes the camera to play back the most recent audio
recording. If the shutter button is not pressed within 5 seconds the camera reverts to normal picture
taking mode. Whilst playing, the LCD display flashes ‘AP’.
Once in Audio Playback mode, repeated presses of the shutter button steps the camera through
each of the audio recordings in the camera (most recent first). Keeping the shutter button pressed
down also allows to cycle through the audio recordings. Pressing the mode button during playback
stops the audio clip.
Note:
16/44
Minimum audio recording length is set to 0.5 seconds.
ADCS 7283313C
STV0681
3.2.5
Camera Modes of Operation
Delete Last Object - dA/dP/dC
This mode is available with audio record hardware fitted.
If the last object captured was an audio recording, 'dA' (delete audio) is displayed, if the last object
was an image, then 'dP' (delete picture) is displayed, or, if the last object was part of a continuous
capture sequence, then 'dC' (delete continuous) is displayed. If the camera is empty, the mode is
suppressed. The mode works like ‘CL’ (Clear All), that is once the mode is selected, pressing the
shutter button once causes the camera to beep and ‘dA’, ‘dP’ or ‘dC’ to start flashing. Pressing the
shutter button again within 5 seconds deletes the last audio clip, picture or continuous capture
sequence.
3.2.6
Continuous mode - Ct
Pressing the shutter button within 5 seconds causes the camera to start taking pictures for as long
as the shutter button is pressed down (and the camera is not full). If the shutter button is not pressed
within 5 seconds the camera reverts to normal picture taking mode.
Note: 1 In continuous mode, the camera allows pictures to be taken regardless of the available light, which
could result in insufficient exposure.
2 In continuous mode, only every alternate field is grabbed hence capture rate is halved. For example,
12.5fps CIF and 7.5fps VGA
3 Continuous mode is suppressed when the FlashGun enable signal (GPIO2) is high.
3.2.7
Self timer - St
Pressing the shutter button starts a 10-second self-timer. The camera issues a short beep every
second, followed by a longer beep. A further beep will then indicate that the picture has been taken
(high beep - picture successful, low beep - insufficient light, picture not taken). The self-timer mode
cannot be selected when the camera is full. The self-timer count down cannot be stopped once it
has started.
3.2.8
Clearing the camera memory - CL
Pressing the shutter button once causes the camera to beep and the ‘CL’ to start flashing. Pressing
the shutter button again within 5 seconds clears all the images/audio clips in the camera and resets
the counter.
3.2.9
Changing picture resolution - Hr/Lr
The resolution option is displayed, either Hr to change to high-resolution mode (if currently in lowresolution mode) or Lr to change to low-resolution (if currently in high-resolution mode). Press the
shutter button within 5 seconds to select the resolution option, the camera beeps and the display is
reset, indicating the number of pictures available in the new mode. The picture resolution can be
changed at any time, that is the camera can store both high and low resolution images.
ADCS 7283313C
17/44
STV0681 Hardware Interfaces
STV0681
4
STV0681 Hardware Interfaces
4.1
Sensor interface
STV0681 uses a standard ST digital interface from the sensor, and the sensor clock input is
provided by an output from STV0681. The design of a camera using this chipset should be
implemented as closely as possible to the reference design (Chapter 7), in which case the chipset
can be regarded as a functional ‘black box’, and no further details regarding the STV0681-sensor
interface are required.
4.2
Memory interface
STV0681 is designed to interface to an external 16Mbit or 64Mbit SDRAM (see Table 1). The
SDRAM device must have a 16 bit wide data bus and operate from a 3.3V supply. Two sizes of
SDRAM memory are supported by STV0681, 16MBits (1M x 16 bits wide) or 64MBits (4M x 16 bits
wide), the memory size is auto-detected by STV0681. STV0681 clocks the SDRAM at 6MHz,
typically this is well below the figures offered by most manufacturers’ devices.
4.2.1
SDRAM current consumption
For maximum system battery life while no pictures are being taken, and to meet requirements for
USB compliance, an SDRAM should be chosen with the lowest possible self refresh current
specification.
In addition, the USB suspend mode current specification requires that the camera consumes less
than 300µA when un-tethered. Meeting this specification, which is included in the requirements for
USB compliance, assumes an SDRAM with up to approximately 250µA self-refresh current, based
on a current consumption of approximately 50µA for STV0681 + support circuit.
18/44
ADCS 7283313C
STV0681
4.2.2
STV0681 Hardware Interfaces
SDRAM interface timing requirements
Figure 4: SDRAM Read Timing (16Mbit device, burst read)
tCK
tL
tH
DCLK
CKE
tCMS
tCMH
Command
ACTIVE
A0-9,BA
ROW
A10
READ
NOP
PRECHARGE
NOP
COLUMN
ROW
tAS
tAH
tCMS
tCMH
tOH
tAC
DQM
DQ
DOUT M
tRCD
DOUT M + 1
DOUT M + 2
DOUT M + 3
READ Latency
tRC
tRAS
tRP
DQ sample
ADCS 7283313C
DQ sample
DQ sample
DQ sample
19/44
STV0681 Hardware Interfaces
STV0681
Figure 5: SDRAM Write Timing (16Mbit device, burst write)
tCK
tL
tH
DCLK
CKE
tCMS
tCMH
Command
ACTIVE
A0-9,BA
ROW
WRITE
NOP
PRECHARGE
NOP
COLUMN
ROW
A10
tAS
tAH
tCMS
tCMH
tDS
DQM
DQ
DIN M
DIN M + 1
tDH
DIN M + 2
tRCD
DIN M + 3
tRC
tRAS
tRP
Table 3: Timing parameters for SDRAM read/write
Symbol
Min.
Max
Units
Symbol
Min.
tCK
166.45
166.89
ns
tDS
81.01
ns
tCH
½
tCK
tDH
83.41
ns
tCL
½
tCK
tRCD
1
tCK
tCK
tRAS
5
tAC
4.2.3
½
Max
5
Units
tCK
tOH
0
ns
tRC
7
tCK
tCMS
82.88
ns
tRP
2
tCK
tCMH
82.85
ns
tRCD
1
tCK
tAS
82.88
ns
tAH
82.76
ns
SDRAM refresh period
The SDRAM refresh period from STV0681 is guaranteed to be inferior or equal to 15.6µs during
‘Snapshot’/self-timer/continuous/tethered video modes of operation (that is not standby mode). In
standby mode, the SDRAM is set to self-refresh, therefore no refresh from STV0681 takes place.
4.2.4
SDRAM initialisation period
The SDRAM initialisation period is currently set to 981µs in STV0681.
20/44
ADCS 7283313C
STV0681
4.3
STV0681 Hardware Interfaces
USB interface
STV0681 includes a USB Version 1.1 compliant Universal Serial Bus Interface, including a
transceiver. This allows direct connection from STV0681 to a USB connector with minimal
additional hardware (that is a small number of passive discretes) - see Chapter 7
The USB interface interfaces the STV0681 to the USB at full speed 12MHz data rate. Some of the
features are:
●
Compliant with USB protocol revision 1.1.
●
USB protocol handling.
●
USB device state handling.
●
Clock and data recovery from USB.
●
Bit stripping and bit stuffing functions.
●
CRC5 checking, CRC16 generation and checking.
●
Serial to parallel conversion.
●
Single bulk-end point.
USB drivers are supplied by ST. For USB timing information, please refer to the USB specification
V1.1.
ADCS 7283313C
21/44
STV0681 Hardware Interfaces
4.4
STV0681
UART module for RS232 interface
The UART module on STV0681 provides a 115200 baud full duplex serial interface to an external
host.
4.4.1
RS232 physical interface
STV0681 does not support direct connection to a RS232 serial link. Physical line driver circuitry is
required, e.g. using a standard RS232 transceiver chip, or by using a small number of low cost
discretes (refer to Reference Design for details). Unscreened cable can be used, a suitable low cost
connector is a 3.5mm stereo audio jack plug.
4.4.2
UART module overview
Receiving data
The UART module in STV0681 receives serial data through the RXD pin. Data reception is initiated
by a 1-to-0 transition on RXD, and the received data is sampled every 8.66µs.
If the RXD input is not 0 when the incoming data is first sampled, the UART module goes back to
look for another 1-to-0 transition. This is to provide rejection of false start bits. If the start bit proves
valid, reception of the rest of the frame proceeds.
Transmitting data
When a transmission is activated by STV0681, the contents of an internal transmit shift register are
shifted onto the TXD pin, every 8.66µs.
The UART operates at 12MHz, which is not an integer multiple of 115200, so the actual baud rate is
115232 +/- 0.3%, which is well within the requirements of a typical 16x oversampling UART, which
can tolerate a 3.75% error in baud rate.
22/44
ADCS 7283313C
STV0681
4.5
STV0681 Hardware Interfaces
Power management and battery type
STV0681 and the SDRAM require a 3.3V supply. When a VV6411 or VV6501 (3.3V) sensor is used,
a single voltage regulator can regulate the supply for all three components from the battery, or the
sensor on-board VReg can be used. These are explained more fully in the reference design.
4.5.1
Power switching to USB
Included in the USB compliance requirements, is the ability of the camera to report to the PC when
connected to the USB bus, whether or not there is a fresh battery in the camera. This means that
power sourcing from USB is required, which also saves on battery life while the camera is used in
USB tethered video mode. In order to allow switching from battery to USB power, some additional
hardware is required.
●
The USBDETECT input to STV0681 is used to detect that a USB power supply is connected
●
If the USB is detected, additional hardware is used to switch off the battery
●
An inrush protection circuit can protect the USB bus from current draw in the case of a low battery/
battery not fitted. This may be necessary to comply with the USB specification.
For precise USB compliance requirements, please consult the USB specification version 1.1.
4.5.2
Switched sensor supply
Dependant on the hardware implementation, the SENSPWR output from STV0681 is used to put
the sensor into suspend mode. This has a significant improvement on battery life.
4.5.3
Battery type
It is possible to use various battery types and configurations. The evaluation kit uses four 1.5V AAA
cells.
ADCS 7283313C
23/44
STV0681 Hardware Interfaces
4.6
STV0681
Quartz crystal
Regardless of the sensor type or anti-flicker requirements, the sensor + STV0681 chipset operates
from a single 12MHz fundamental quartz crystal. For specification requirements, see Table 13.
STV0681 includes an on-chip low jitter PLL. For PLL characteristics, see Table 12.
4.7
Numeric LCD interface
STV0681 supports a 2-digit LCD panel only, for alpha-numeric display.
4.7.1
LCD types
STV0681 connects to a non multiplexed, direct drive LCD with 2 x 7 segments. Many LCD types are
compatible with this interface. The LCD refresh frequency is 34.7Hz.
4.7.2
LCD interface pinout
The convention for segment numbering is as follows: '0' connects to segment 'a', '1' connects to
segment 'b', and so on, where a to g are standard for all 7-segment displays, as well as an LCD
common output, giving fifteen signals in total.
24/44
ADCS 7283313C
STV0681
4.8
STV0681 Hardware Interfaces
Switches and LED’s
The GPIO lines on STV0681 have the following pre-defined functions, see Section 2.2 for user
interface functionality.
MODE push button and SHUTTER push button: GPIO0 and GPIO1: both push button inputs have
internal de-bounce circuits, reducing the amount of hardware required externally. It is
recommended that labelling is used on the camera casing to help the user understand the
functioning of the 2-button interface.
4.8.1
Input to select between 50 and 60Hz flicker frequency: GPIO3
This allows for factory setting of the anti-flicker frequency, dependant on the final country of
destination. See also Section 2.6. The polarity of this selection is detailed in the reference design.
4.8.2
LED indicator output: GPIO5
The LED output has an 8mA current sinking capability.
4.8.3
Other pins: GPIO2, 4, 6, 7
With STV0681, these pins are used, as detailed in Table 4.
Table 4: Other GPIO usage with STV0681
GPIO
2
4
6
7
Audio Record
No
Yes
No
No
Audio
Playback
No
No
Yes
No
Flashgun
Yes
No
No
Yes
Their specific functions are detailed in the reference design and in the following documents
available from ST:
●
Audio: application note AN1310
●
Flashgun: application note AN1312
4.8.4
Audio Record Hardware interface
STV0681 implements the A/D conversion by outputting successive analogue levels (successive
approximation) through the DAC output, which are compared with the actual signal level (output
from the sensor microphone preamplifier), and the resulting high or low signal from the comparator
is read at GPIO4. The sampling frequency is 11kHz, and the successive approximation is done at 8
bits resolution per sample. It is not possible to speed up the sampling frequency due to the limitation
of STV0681 processing speed.
An actual hardware implementation is given in the audio application note AN1310.
4.8.5
Audio Playback Hardware interface
STV0681 outputs the desired signal level through the DAC output, which is amplified to the speaker
or headphone socket. GPIO6 is used to switch off the amplifier during periods of audio recording, to
prevent the successive approximation waveform from being heard during periods of recording, and
to reduce the power consumption and unwanted crackle through the speaker.
An actual hardware implementation is given in the audio application note AN1310.
ADCS 7283313C
25/44
STV0681 Hardware Interfaces
4.9
STV0681
Flashgun hardware interface
STV0681 will revert to flashgun exposure when it detects GPIO2 is high. Ideally the hardware
should combine the two factors of (a) user intention (e.g. user switches on flashgun) and (b) charge
sensing (i.e. flash is charged up and ready to fire).
These two factors (a) and (b) are independent, since there may be a delay of several seconds
between switching on the flashgun charger, and the flashgun being able to fire. To revert to flashgun
exposure before the flashgun is completely charged up would cause very bad pictures to be taken
in low light conditions because there is no “low light” threshold when flashgun exposure is enabled,
since the camera expects a flash to fire. A suggested flashgun hardware interface is given in the
flashgun application note AN1312.
When flashgun exposure is enabled and the shutter button is pressed, a picture is taken and the
flash trigger pin GPIO7 is pulsed low at the correct point in time so that all lines of the CMOS imager
are exposed.
4.10
IR filter
An Infra-Red Blocking Filter is required to achieve correct colour response. The exact specification
for the IR filter characteristics are given in the reference design manual.
26/44
ADCS 7283313C
STV0681
5
Customising the STV0681
Customising the STV0681
The firmware inside the STV0681 is stored in ROM and may not be changed. It is possible,
however, to use an external serial EEPROM to store certain information to allow a degree of
customization of the device.
The STV0681 reports a USB Vendor ID (VID) of 0553(hex) and a Product ID (PID) of 0202 (hex).
Alternative values for the VID and PID as well as Manufacturer and Product strings may be stored in
an external EEPROM.
In addition to USB descriptor information, the EEPROM may also be used to set various other
parameters as follows:
●
Auto power-down time: this is the length of time before the STV0681 shuts down after no activity.
●
Mode button power-down time: the length of time you must hold the Mode button to powerdown the
system.
●
50Hz/60Hz flicker-free selection: the EEPROM allows this selection to be via a GPIO pin on the
STV0681 or fixed at either 50Hz or 60Hz
●
Number of self-timer beeps
5.1
External EEPROM
An external 128byte serial EEPROM may be used in conjunction with STV0681 to hold customer
specific information.
The EEPROM is connected onto the sensor IIC bus and must be set to IIC address A0 (hex). The
EEPROM is auto-detected by the STV0681 and no additional changes need to be made. A suitable
EEPROM device is manufactured by STMicroelectronics part number M24C01W (alternatives are
available from other suppliers).
ADCS 7283313C
27/44
Customising the STV0681
5.2
EEPROM data format
Location(decimal)
5.3
STV0681
Contents
0
Leave blank
1
VidLo, The low byte of the Vendor ID
2
VidHi, The high byte of the Vendor ID
3
PidLo, The low byte of the Product ID
4
PidHi, The high byte of the Product ID
5
Max Power (in units of 0.5mA)
6
Max Power with audio playback enabled (in units of 0.5mA)
7
Auto powerdown time Hi byte (in units of 256ms)
8
Auto powerdown time Lo byte (in units of 10ms)
9
Mode button press time Hi byte (in units of 256ms)
10
Mode button presss time Lo byte (in units of 10ms)
11
50Hz/60Hz flicker free selection
0 = board link (GPIO3) , 1 = 50Hz, 2 = 60Hz
12
Number of self-timer beeps
13
CheckSum - low byte of sum of EEPROM locations 1 to 12
inclusive.
20
Length of Manufacturer String
21-54 (max)
Manufacturer String (ASCII codes)
55
Length of Product String
56-89 (max)
Product String (ASCII codes)
90
Length of Interface0 String
91-127 (max)
Interface 0 String (ASCII codes)
Programming the EEPROM
There is no facility to program the EEPROM using the STV0681 itself and so the device must be
programmed before fitting it to the PCB.
28/44
ADCS 7283313C
STV0681
6
Software support
6.1
General features
Software support
The chipset is a dual-mode camera, i.e. stills and video, and is supported by a range of
demonstration software, standard drivers, and software development options.
PC
Driver software is available to support both USB and RS232 interfaces. Drivers are available for
TWAIN, WIA, Video for Windows (VfW) and DirectShow (DS) depending on the Operating System
as listed below:
●
Win98/Win98SE/WinME – VfW and TWAIN
●
Win2k – DS, VfW and TWAIN
●
WinXP – DS, VfW, WIA and TWAIN
Mac
Quicktime drivers and a Photoshop stills plug in for MacOS 8.6/9.0/9.1/9.2 are supported.
The driver will also run under MacOS X in Classic Mode.
Example software applications (PC only) are provided to create. AVI video files from untethered
continuous capture of images (AVICreator), to upload still images and recorded sounds
(LCDCdemo) and to download.WAV files from the PC to the camera (CustomSound). In each case,
PC source code is provided to assist in OEM software development using the SDK.
ST colour processing and defect detection/correction software runs on the host and is supplied
under licence agreement as part of all host software/drivers/SDK
6.1.1
Still image upload
This is available through demonstration software, OEM custom software, or using standard TWAIN
applications. Features include:
●
Fast upload through USB, or upload through RS232.
●
Colour display of image thumbnails for picture selection.
●
Download of full image once selected by user software.
●
Automatic detection and correction of sensor defects
●
Colour processing of full image, using the ST colour process
The above features also apply to “AVI Creator” or any OEM custom software for AVI video creation
at part of pictures taken while un-tethered, since this is essentially a “stills” function.
6.1.2
Streaming video (only while tethered to USB)
This is available through demonstration software, or using standard VfW applications. Features
include:
●
Streaming video through standard VfW driver
●
Automatic detection and correction of sensor defects
●
Colour processing of full image, using the ST colour process
ADCS 7283313C
29/44
Software support
6.2
STV0681
Software installation
The following software support is only available to OEMs. Access to the latest installation files is
possible through a password-protected web page, contact ST for details. The installation files are for
the following:
●
Drivers (always check the Web site for latest driver version).
●
EVK software, i.e. LCDCdemo.exe and AVIcreator.exe, G2Video.exe, and CTItest2.exe
●
SDK installation: source code for sample applications, and documentation
6.2.1
Driver support available
Table 5: Driver choices
RS232
USB
Microsoft Windows:
Microsoft Windows:
PC Operating system
Win9x, WinNT4, Win2k,
Windows Millennium
Windows XP
Win98 and Win2k only,
Windows millenium
Windows XP
Mac OS
N/A
8.6, 9.0, 9.1, 9.2
Interface type:
6.2.2
EVK software
Note:
The following is also supplied with evaluation kits/demonstration units, but all the following software
is only for demonstration purposes and should NOT be supplied as an end-user product. However,
application-level source code (i.e. not driver/colour processing source) for LCDCdemo.exe, AVI
creator, and CTItest.exe is available as part of the SDK, which allows similar applications to be built
by the software developer:
6.2.3
1
Simple demonstration software LCDCdemo.exe for uploading thumbnails and images.
2
AVIcreator.exe software for uploading continuous images for creating ‘movie’ clips.
3
G2Video.exe is a VfW application which shows streaming video while tethered to USB and
allows creation of.AVI video clips.
4
CTItest.exe is only for debugging purposes, for software developers using the SDK
Software Development Kit (SDK) and source code
A software development kit allows the OEM to develop a custom application which calls the same
range of drivers as listed in Section 6.2.1, hence allowing the OEM application to perform picture
download, thumbnail display, and colour processing using the ST colour process. Inclusion of
source code for the applications listed in Section 6.2.2 allows the software developer to use these
as the basis for their own application.
The SDK is supplied by ST as a 32-bit DLL format, running on Microsoft Windows 98/Win2KTM, and
accessed through a documented software interface. Development requires Microsoft Visual Studio
Version 6 or later. This provides the basis for developing a custom software application for stills.
Note:
30/44
Source code for PC Drivers, Defect Correction and Colour Processing algorithms are not available.
ADCS 7283313C
STV0681
Detailed Chipset Specifications
7
Detailed Chipset Specifications
7.1
Typical camera specifications
The following data assumes that the camera has been built according to the ST Reference Design.
Dual USB or battery power supply is only possible when the required power switching hardware is
included.
Figures are approximate and depend on actual components sources.
Table 6: Typical camera specifications
Supply voltage
4.1-6V (when powered from battery or USB)
Operating temperature range
0oC - 40oC
Max. RS232 cable length supported
2m
CIF output
352 x 288 pixels
QCIF output
176 x 144 pixels
VGA output
640 x 480 pixels
QVGA output
320 x 240 pixels
SDRAM storage and image upload format
Raw Bayer
PC driver output format
Colour RGB bitmap
Table 7: Approximate shutter speeds
7.2
Sensor resolution
Min.
Max
CIF
8 µs
44 ms
VGA
8 µs
66 ms
Absolute maximum ratings
Table 8: STV0681 absolute maximum ratings
Parameter
Range
Units
Ambient temperature
0 to 40
°C
Storage temperature
-50 to 150
°C
0-VDD
V
Voltage on USB D+/D-
ADCS 7283313C
31/44
Detailed Chipset Specifications
7.3
STV0681
STV0681 specifications
Table 9: STV0681 specifications
Parameter
Supply voltage
Min.
Typ.
Max.
Units
3.0
3.3
3.6
V
18
-
mA
10
-
µA
Current consumption (normal operation)
Stand-by current consumption
-
Package
100TQFP (14x14x1.4)
Exposure control
7.4
1 000 000: 1
USB specifications
Table 10: STV0681 USB specifications
Parameter
Description
Min.
Typ.
Max.
Units
3.0
3.3
3.6
V
0.8
V
VDD
Power Supply
VILU
USB differential pad D+/D- input low
VIHU
USB differential pad D+/D- input high (driven)
2.0
VIHUZ
USB differential pad D+/D- input high (floating)
2.7
VDI
USB differential pad D+/D- input sensitivity
0.2
VCM
USB differential pad D+/D- common mode voltage
0.8
VOLU
USB differential pad D+/D- output low voltage
VOHU
Notes
V
3.6
V
V
1
2.5
V
2
0.0
0.3
V
USB differential pad D+/D- output high voltage
2.8
3.6
V
VCRS
USB differential pad D+/D- output signal cross over
voltage
1.51
1.79
V
RPU
USB differential pad D+/D- pull up resistor
1.425
1.575
kΩ
RPD
USB differential pad D+/D- pull-down resistor
14.25
15.75
kΩ
TFR
Rise Time
4
20
ns
TFF
Fall Time
4
20
ns
TFRFM
Differential Rise Time and Fall Time Matching
96
98
%
Note 3
ZDRV
Driver Output Resistance
30.0
Ω
Note 4
24.7
26.6
Note: 1 VDI = |(D+) - (D-)|
2 VCM includes VDI range.
3 TFRFM =(TFR / TFF).
4 ZDRV includes an external resistor of 20 Ohms serial to this transceiver.
32/44
ADCS 7283313C
STV0681
7.5
Detailed Chipset Specifications
DC characteristics
Table 11: STV0681 DC characteristics
Parameter
Description
Min.
Typ.
Max.
Units
0.35 VDD
V
VII
CMOS input low voltage
VIH
CMOS input high voltage
VT+
CMOS schmitt input low to high threshold voltage
2.15
V
VT-
CMOS schmitt input high to low threshold voltage
1.05
V
VT
Threshold point
1.65
V
VOH
Output high voltage
VOL
Output low voltage
7.6
0.65 VDD
V
2.4
V
0.4
V
PLL characteristics
Table 12: STV0681 PLL characteristics
Parameter
Conditions
Peak to peak jitters
@VCOfreq = 240MHz - 312MHz
Duty cycle
Operating voltage range
Symbol
Min.
Typ.
Max.
Unit
--
--
--
500
ps
--
45
50
55
%
VDD
3
3.3
3.6
V
Input low voltage
VDD=3.3V
VIL
-
0.8
V
Input high voltage
VDD=3.3V
VIH
0.7VDD
VDD
V
Ready
--
--
0.1
ms
Tsr(Fout)
--
0.100+0.1082*CL
--
ns
Pull in Time + Locking Time
Output Slew Rate
7.7
CL: Output Load (pF)
Crystal tolerance
Table 13: STV0681 crystal tolerance
Parameter
Min.
Crystal specification
Typ.
Max.
Units
50/50/10/30 (12mhz Fundamental)
Crystal frequency
12.000
MHz
Frequency tolerance
50
ppm
Temperature stability
50
ppm
Operating temperature
-10
ADCS 7283313C
°C
33/44
Detailed Chipset Specifications
7.8
STV0681
Typical current consumption of complete camera
The following data assumes that the camera has been built according to reference design referred
to in Chapter 10. Figures are approximate and depend on actual components sources - see notes.
The sensor operates at @ 3.3V DC
Table 14: Current consumption, complete STV0681+VV6411/6501 camera
Mode
Typical
Comments
’Snapshot’/Continuous/
Self timer mode
(while un-tethered)
60mA
Assuming appropriate hardware included, power is sourced
from PC while USB connected.
’Snapshot’/Continuous/
Self timer mode
(while tethered to PC)
60mA
While playing back audio
sounds through speaker
90mA
Standby mode
(when NOT connected to
USB)
Assuming 8Ω speaker as explained in application note
AN1310
Approx. 270µA + SDRAM
self-refresh current
(see Note 2) + sensor
suspend mode current
Total current in this mode equals:
STV0681 standby current consumption (see Note 1)
+ SDRAM self-refresh current (see Note 2)
+ peripheral circuitry (approx. 50µA).
+ Sensor suspend mode current
PC Suspend mode
Approx. 300µA + SDRAM
(when connected to USB): self-refresh current
(see Note 2) + sensor
Sensor SUSPEND pin
suspend
mode current
asserted
Standby mode
Total current in this mode equals:
STV0681 Standby current consumption (see Note 1)
+SDRAM self-refresh current (see Note 2)
+ peripheral circuitry (approx. 50µA)
+ 200µA, based on 1.5k pull-up in camera and 15k pulldown in PC.
+ Sensor suspend mode current
Approx. 270µA + SDRAM
self-refresh current
(see Note 2)
Total current in this mode equals:
Approx. 100µA + SDRAM
(when connected to USB): self-refresh current
sensor powered off using (see Note 2)
FET (see Note 3)
Total current in this mode equals:
(when not connected to
USB): sensor powered off
using FET (see Note 3)
PC Suspend mode
STV0681 Standby current consumption (see Note 1)
+SDRAM self-refresh current (see Note 2)
+ peripheral circuitry (approx. 50µA).
STV0681 Standby current consumption (see Note 1)
+SDRAM self-refresh current (see Note 2)
+ peripheral circuitry (approx. 50µA).
Note: 1 See Table 9 from Section 7.3
2 From limited evaluation, typical self-refresh current figures of certain SDRAM chips are well below
manufacturers’ maximum specification, e.g. 100-250µA.
3 Option included in reference design to save current consumption, which can increase battery life
and increase chances of meeting USB suspend mode compliance requirements.
34/44
ADCS 7283313C
STV0681
STV0681 pin description
8
STV0681 pin description
8.1
STV0681 pinout
AMP_EN
FL_TRIG
SENSPWR
SENSRST
SENS_CLK
QCLK
SD[0]
SD[1]
SD[2]
SD[3]
SDA
SCL
RXD
67
66
65
64
63
62
61
60
59
58
57
56
55
PLL_AVDD
LED
68
PLL_AVSS
VDD
69
51
VSS
70
PLL_GVSS
COMP_OUT
71
52
50/60
72
TXD
FLASH_EN
73
53
SHUTTER
74
54
MODE
75
Figure 6: STV0681 pinout diagram
AUD_VSS
76
50
RESET
LO_BAT_REF
77
49
XOUT
LO_BAT
78
48
XIN
DACRES
79
47
TEST2
DACOUT
80
46
TEST1
AUD_VDD
81
45
TEST0
PIEZO
82
44
USB-
LCD_COM
83
43
USB+
VSS
84
42
USB_DET
VDD
85
41
AD_4
LCD2_6
86
40
AD_3
LCD2_5
87
39
VDD
LCD2_4
88
38
VSS
LCD2_3
89
37
AD_5
LCD2_2
90
36
AD_2
LCD2_1
91
35
AD_6
LCD2_0
92
34
AD_1
LCD1_6
93
33
AD_7
LCD1_5
94
32
AD_0
LCD1_4
95
31
AD_8
LCD1_3
96
30
AD_10
LCD1_2
97
29
AD_9
LCD1_1
98
28
AD_13
LCD1_0
99
27
AD_11
100
26
AD_12
25
CS
24
CKE
23
22
DCLK
RAS
21
CAS
20
16
DQ_7
DQ_8
DQML
DQMU
15
DQ_9
19
14
WE
12
VSS
DQ_10
DQ_6
18
11
VDD
ADCS 7283313C
17
10
DQ_5
13
9
8
DQ_4
DQ_11
7
6
DQ_3
DQ_12
5
4
3
2
1
TQFP100
DQ_15
DQ_1
DQ_14
DQ_2
DQ_13
DQ_0
STV0681
35/44
STV0681 pin description
8.2
STV0681
STV0681 pin description
Table 15: STV0681 pin listing
Pin no.
Signal
Type
Description
drive
Sensor Interface
65
SENSPWR
Output, active
high
Power-up Sensor
2mA
(SL)
64
SENSRST
Output, active low
Reset Sensor
2mA
(SL)
56
SCL
Input/Output
(OD,T)
Sensor serial interface
4mA
(SL)
57
SDA
Input/Output
(OD,T)
Sensor serial interface
4mA
(SL)
58
SD[3]
Input (S,T)
Sensor data
59
SD[2]
Input (S,T)
Sensor data
60
SD[1]
Input (S,T)
Sensor data
61
SD[0]
Input (S,T)
Sensor data
62
QCLK
Input (S,T)
Qualification clock from sensor
63
SENS_CLK
Output
Clock output to sensor
4mA
I/O and Camera Control pins
75
MODE
Debounced input
Push button (Wake-up/Mode)
74
SHUTTER
Debounced input
Push button (Shutter/Confirm)
73
FLASH_EN
Input
Enable Flash Exposure (Active High)
72
50/60_SEL
Input
S elect between 50Hz and 60Hz lighting
71
COMP_OUT
Input
Output from Audio Comparator
68
LED
Output (OD)
LED indicator
8mA
(SL)
67
AMP_ENABLE
Output, active low
(OD)
Audio Amplifier Enable
8mA
(SL)
66
FL_TRIG
Output, active low
(OD)
Flashgun trigger
8mA
(SL)
Input (S)
Detect Power source from USB.
USB Interface
42
USBDET
(For camera with RS232 only, this pin should be tied
to GND)
43
DATA+
Input/Output
USB bus
(For camera with RS232 only, this pin should be
connected to test points to allow for USB production
test (lens focussing))
44
DATA-
Input/Output
USB bus.
(For camera with RS232 only, this pin should be
connected to test points to allow for USB production
test (lens focussing))
36/44
ADCS 7283313C
USB
specific
ation
V1.1
complia
nt I/O
STV0681
STV0681 pin description
Table 15: STV0681 pin listing
Pin no.
Signal
Type
Description
drive
RS232 Interface
54
TXD
Output
Serial data transmit
(For camera with USB only, this pin should be tied to
RXD)
55
RXD
Input (S)
4mA
(SL)
Serial data receive
(For camera with USB only, this pin should be tied to
TXD)
STV0680B Master Clocks and Reset
48
XIN
Input
Quartz Crystal IN
49
XOUT
Output
Quartz Crystal OUT
50
RESET
Input (S)
Active (LOW) STV0680B reset
System Memory (SDRAM) Interface
20
DQMU
Output
Data input/output mask for dram_DQ[15:8]
2mA
(SL)
22
DCLK
Output
Clock: all SDRAM input signals are sampled on the
positive edge
4mA
(SL)
24
CKE
Output
Clock enable: activates (HIGH) and deactivates
(LOW) the SDRAM CLK signal
2mA
(SL)
32
AD0
Output
SDRAM address A0
2mA
(SL)
34
AD1
Output
SDRAM address A1
2mA
(SL)
36
AD2
Output
SDRAM address A2
2mA
(SL)
40
AD3
Output
SDRAM address A3
2mA
(SL)
41
AD4
Output
SDRAM address A4
2mA
(SL)
37
AD5
Output
SDRAM address A5
2mA
(SL)
35
AD6
Output
SDRAM address A6
2mA
(SL)
33
AD7
Output
SDRAM address A7
2mA
(SL)
31
AD8
Output
SDRAM address A8
2mA
(SL)
29
AD9
Output
SDRAM address A9
2mA
(SL)
30
AD10
Output
SDRAM address A10
2mA
(SL)
27
AD11
Output
SDRAM address A11 for 64M SDRAM or BA for 16M
SDRAM
2mA
(SL)
26
AD12
Output
SDRAM address A12, BA0 for 64M SDRAM, unused
on 16M
2mA
(SL)
ADCS 7283313C
37/44
STV0681 pin description
STV0681
Table 15: STV0681 pin listing
Pin no.
38/44
Signal
Type
Description
drive
28
AD13
Output
SDRAM address A13, BA1 for 64M SDRAM, unused
on 16M
2mA
(SL)
25
CS
Output, active low
Chip select: enables (registered LOW) and disables
(registered HIGH) the SDRAM command decoder.
2mA
(SL)
23
RAS
Output, active low
SDRAM row address strobe command
2mA
(SL)
21
CAS
Output, active low
SDRAM column address strobe command
2mA
(SL)
19
WE
Output, active low
SDRAM write enable command
2mA
(SL)
18
DQML
Output
Data input/output mask for dram_DQ[7:0]
2mA
(SL)
100
DQ0
Input/Output
SDRAM Data Bus
2mA
(SL)
2
DQ1
Input/Output
SDRAM Data Bus
2mA
(SL)
4
DQ2
Input/Output
SDRAM Data Bus
2mA
(SL)
6
DQ3
Input/Output
SDRAM Data Bus
2mA
(SL)
8
DQ4
Input/Output
SDRAM Data Bus
2mA
(SL)
10
DQ5
Input/Output
SDRAM Data Bus
2mA
(SL)
14
DQ6
Input/Output
SDRAM Data Bus
2mA
(SL)
16
DQ7
Input/Output
SDRAM Data Bus
2mA
(SL)
17
DQ8
Input/Output
SDRAM Data bus
2mA
(SL)
15
DQ9
Input/Output
SDRAM Data bus
2mA
(SL)
13
DQ10
Input/Output
SDRAM Data bus
2mA
(SL)
9
DQ11
Input/Output
SDRAM Data Bus
2mA
(SL)
7
DQ12
Input/Output
SDRAM Data Bus
2mA
(SL)
5
DQ13
Input/Output
SDRAM Data Bus
2mA
(SL)
3
DQ14
Input/Output
SDRAM Data Bus
2mA
(SL)
1
DQ15
Input/Output
SDRAM Data Bus
2mA
(SL)
ADCS 7283313C
STV0681
STV0681 pin description
Table 15: STV0681 pin listing
Pin no.
Signal
Type
Description
drive
LCD Interface
83
LCDCOM
Output
LCD Common
4mA
(SL)
93
LCD1_6
Output
LCD digit 1 segment G
2mA
(SL)
94
LCD1_5
Output
LCD digit 1 segment F
2mA
(SL)
95
LCD1_4
Output
LCD digit 1 segment E
2mA
(SL)
96
LCD1_3
Output
LCD digit 1 segment D
2mA
(SL)
97
LCD1_2
Output
LCD digit 1 segment C
2mA
(SL)
98
LCD1_1
Output
LCD digit 1 segment B
2mA
(SL)
99
LCD1_0
Output
LCD digit 1 segment A
2mA
(SL)
86
LCD2_6
Output
LCD digit 2 segment G
2mA
(SL)
87
LCD2_5
Output
LCD digit 2 segment F
2mA
(SL)
88
LCD2_4
Output
LCD digit 2segment E
2mA
(SL)
89
LCD2_3
Output
LCD digit 2segment D
2mA
(SL)
90
LCD2_2
Output
LCD digit 2segment C
2mA
(SL)
91
LCD2_1
Output
LCD digit 2 segment B
2mA
(SL)
92
LCD2_0
Output
LCD digit 2 segment A
2mA
(SL)
Output
Direct connection to piezo buzzer
8mA
(SL)
Piezo Interface
82
PIEZO
Battery Level Comparator Interface
78
LO_BAT
Input (A)
Battery level comparator input. The voltage on
low_bat is compared to the reference to determine
the battery status
77
LO_BAT_REF
Input (A)
1.22V battery level comparator reference input
ADCS 7283313C
39/44
STV0681 pin description
STV0681
Table 15: STV0681 pin listing
Pin no.
Signal
Type
Description
drive
Power and Ground
12, 38,
70, 84
DVSS
Power pin
Digital Ground
11, 39,
69, 85
DVDD
Power pin
Digital Power
76
AUD_VSS
Power pin
Audio DAC Ground. Requires clean supply.
81
AUD_VDD
Power pin
Audio DAC Power. Requires clean supply.
53
PLLGVSS
Power pin
PLL Guard Ground
51
PLLAVDD
Power pin
PLL Analog Power
52
PLLAVSS
Power pin
PLL Analog Ground
Non-user pins
45
TEST0
Input
Non-user pin - connect to 3V3
46
TEST1
Input
Non-user pin - connect to 3V3
47
TEST2
Input
Non-user pin - connect to 3V3
79
DACRES
I(A)
DAC bias amplifier reference input.
80
DACOUT
O (A)
8-bit DAC current source output.
Key
SL
slew rate limited output
OD
open drain output
S
Schmidt input
A
analogue input/output
T
5V tolerant pad (these pads do not have diode protection)
Note: 1 Where the I/O pad type is not explicitly defined, assume CMOS.
40/44
ADCS 7283313C
0-10mA
STV0681
9
STV0681 package mechanical data
STV0681 package mechanical data
mm
inch
Dim.
Min.
Typ.
Max.
A
Min.
Typ.
1.60
A1
0.05
A2
1.35
B
0.17
C
0.09
0.063
0.15
0.002
0.006
1.40
1.45
0.053
0.055
0.057
0.22
0.27
0.007
0.009
0.011
0.20
0.003
0.008
D
16.00
0.630
D1
14.00
0.551
D3
12.00
0.472
e
0.50
0.019
E
16.00
0.630
E1
14.00
0.551
E3
12.00
0.472
L
0.45
L1
Max.
0.60
0.75
0.018
1.00
K
0.024
0.030
TQFP100
0.039
3
3.5° (min.), 7° (max.)
D
A
D1
A2
D3
A1
75
51
76
50
0.076mm
.003 inch
Seating Plane
e
E3 E1
E
B
Pin 1
identification
100
26
1
25
K
TQFP100M
C
L
L1
ADCS 7283313C
41/44
Evaluation Kit (EVK)
10
STV0681
Evaluation Kit (EVK)
STMicroelectronics can supply an Evaluation Kit for initial evaluation and design-in.
The EVK includes an STV0681 Motherboard PCB and two lensed sensor daughter boards (CIF and
VGA). Additional motherboards and daughter boards may be ordered separately. The EVK PCB
includes SDRAM memory, connectors, numeric LCD display, battery holder, push buttons/switches,
audio record and playback circuitry, flashgun interface circuitry, and a flashgun hotshoe connector
(for use of a standard camera flashgun). Optional PCB links enable alternate functionality, and
demonstration software is included, allowing for tethered video, upload to the PC of pictures,
sounds, and AVI movie clips, and download to the camera of custom sounds.
A reference design manual, giving the camera designer everything required for standard features
and audio record/playback is available, including schematics, explanatory notes, parts list, and
layout advice.
10.1
Ordering details
Table 16: Ordering details for STV0681 + VV6411/6501 Evaluation Kits
Description
Part number
STV0681 companion processor
STV0681
VV6411 CIF color CMOS sensor (36LCC package)
VV6411C036
VV6501 VGA color CMOS sensor (36LCC package)
VV6501C001
Complete Evaluation Kit
STV0681 complete Evaluation Kit
(includes STV-681-M01, STV-6411C-D01 and STV6501C-D01)
STV-681-E01
Additional EVK Components
Evaluation Kit Motherboard
Note:
42/44
STV-681-M01
Sensor Daughter Board with VV6411
STV-6411C-D01
Sensor Daughter Board with VV6501
STV-6501C-D01
All Evaluation Kits include hardware and software support for Audio, Custom sounds, and Flashgun
features.
ADCS 7283313C
STV0681
10.2
Evaluation Kit (EVK)
Technical support
Technical support information, such as datasheets, software downloads,etc, for products of the
STMicroelectronics Imaging Division can be found at www.st.com (click on Imaging products)
General sales/technical enquiries can be directed to regional email contacts:
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
ADCS 7283313C
43/44
STV0681
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
© 2003 STMicroelectronics - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
www.st.com
ADCS 7283313C
44/44