ARS35 / AR35 35.0 AMPS. High Current Plastic Silicon Rectifiers Voltage Range 50 to 1000 Volts Current 35.0 Amperes ARS Features AR Plastic material used carries Underwriters Laboratory Classification 94V-O Low cost construction utilizing void-free molded plastic technique Low cost Diffused junction Low leakage High surge capability High temperature soldering guaranteed: 260oC for 10 seconds Mechanical Data Case: Molded plastic case Terminals: Plated terminals, solderable per MILSTD-202, Method 208 Polarity: Color ring denotes cathode end Weight: 0.07 ounce, 1.8 grams Mounting position: Any Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% ARS Type Number Maximum Recurrent Peak Revere Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @Tc = 150℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) at TJ=150oC Maximum Instantaneous Forward Voltage @ 35A Maximum DC Reverse Current @ Tc=25℃ at Rated DC Blocking Voltage @ Tc=100℃ Typical Reverse Recovery Time (Note 2) Typical Junction Capacitance ( Note 1 ) TJ=25oC Typical Thermal Resistance ( Note 3 ) AR 35A ARS 35B AR 35B ARS 35D AR 35D ARS 35G AR 35G ARS 35J AR 35J ARS 35K AR 35K 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 1000 560 700 800 1000 Symbol 35A VRRM VRMS VDC ARS 35M AR 35M Units V V V I(AV) 35 A IFSM 500 A VF 1.0 V Trr 5.0 250 3.0 uA uA uS Cj 300 pF RθJC 1.0 ℃/W ℃ IR TJ, TSTG -50 to +175 Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 2. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 3. Thermal Resistance from Junction to Case, Singe Side Cooled. Operating and Storage Temperature Range - 502 - RATINGS AND CHARACTERISTIC CURVES (ARS35 THRU AR35) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1000 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 35 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 30 25 20 15 10 5 0 125 8.3ms Single Half Sine Wave JEDEC Method 500 100 50 135 145 155 165 1 175 2 CASE TEMPERATURE. ( C) 20 10 5 o 50 100 NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL FORWARD CHARACTERISTICS FIG.4- TYPICAL REVERSE CHARACTERISTICS 1000 100 60 INSTANTANEOUS REVERSE CURRENT. ( A) 100 10 1 Tj=100 0C 20 10 6 4 2 1 Tj=25 0C 0.6 0.4 0 Tj=25 C PULSE WIDTH-300 S 2% DUTY CYCLE 0.1 0.6 1.0 1.4 1.8 2.2 0.2 0.1 2.6 FORWARD VOLTAGE. (V) 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE 1000 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 40 500 Tj=25 0C 100 50 1 2 5 10 REVERSE VOLTAGE. (V) - 503 - 20 50 100