CURRENT 1.0 Ampere VOLTAGE 50 to 1000 Volts 1N4001 THRU 1N4007 Features · The plastic package carries Underwrites Laboratory Flammability Classification 94V-0 · Construction utilizes void-free molded plastic technique · Low reverse leakage · High forward surge current capability · High temperature soldering guaranteed : 250℃/10 seconds, 0.375"(9.5mm) lead length, 5lbs.(2.3kg). DO-41 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) Mechanical Data · Case : JEDEC DO-41 molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.012 ounce, 0.33 gram 1.0(25.4) MIN. 0.034(0.9) 0.028(0.7) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols 1N 4001 1N 4002 1N 4003 1N 4004 1N 4005 1N 4006 1N 4007 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length TA=75℃ I(AV) 1.0 Amp Peak forward surge current 8.3ms half sine wave superimposed on rated load (JEDEC method) at TA=75℃ IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF 1.1 Volts Maximum reverse current at rated DC blocking voltage TA=25℃ TA=100℃ IR 5.0 50.0 μA RθJA 50.0 RθJL 25.0 Typical junction capacitance (Note 1) CJ 15.0 pF Maximum DC blocking voltage temperature TA +150 ℃ TJ TSTG -50 to +175 ℃ Typical thermal resistance (Note 2) Operating and storage temperature range Notes: (1) Measured at 1MHz and applied reverse voltage of 4.0V DC. (2) Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length, P.C.B. mounted ℃/W RATINGS AND CHARACTERISTIC CURVES 1N4001 THRU 1N4007 FIG.1-FORWARD CURRENT DERATING CURVE FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0.8 20 INSTANTANEOUS FORWARD CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES 1.0 0.6 0.4 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.2 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( ℃) 10 1 TJ=25℃ PULSE WIDTH=300μS 0.1 1% DUTY CYCLE 0.01 FIG.3-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 0.6 0.8 1.0 1.2 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 40 30 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 10 10 0 1 10 100 NUMBER OF CYCLES AT 60Hz FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 100 INSTANTANEOUS REVERSE CURRENT (μA) PEAK FORWARD SURGE CURRENT (AMPERES) 50 TJ=100℃ 1.0 0.1 TJ=25℃ 0.01 0 20 40 60 80 100 TJ=25℃ PERCENT OF RATED PEAK REVERSE VOLTAGE (%) 10 1 0.1 1 10 REVERSE VOLTAGE. VOLTS 100 120 140