SFAF1001G THRU SFAF1008G Isolation 10.0 AMPS. Glass Passivated Super Fast Rectifiers Voltage Range 50 to 600 Volts Current 10.0 Amperes ITO-220AC Features .185(4.7) .406(10.3) .173(4.4) Low forward voltage drop High current capability High reliability High surge current capability .390(9.90) .124(3.16) .118(3.00) .13 4(3. 4)D IA . 112 (2. 85) . 11 3(3. 0)D IA . 100 (2.5 5) .2 72( 6. 9) .2 48( 6. 3) . 606(1 5.5 ) . 583(1 4.8 ) Mechanical Data .0 63 (1 .6 ) MA X Cases: ITO-220AC molded plastic Epoxy: UL 94V-O rate flame retardant Terminals: Leads solderable per MILSTD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260oC/10 seconds/.16”,(4.06mm) lead lengths at 5 lbs., (2.3kg) tension Weight: 2.24 grams .161(4.1) .146(3.7) .110( 2.8) . 071 (1. 8) . 543( 13. 8) MA X . 512( 13. 2) .0 98(2 .5) 2 . 10 0( 2 . 55) . 100 (2.5 5) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol SFAF SFAF SFAF SFAF Type Number SFAF SFAF SFAF SFAF 1001G 1002G 1003G 1004G 1005G 1006G 1007G 1008G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 10.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ VRRM VRMS VDC Maximum Reverse Recovery Time (Note1) Trr Cj RθJC TJ Typical Junction Capacitance (Note 2) Typical Thermal Resistance (Note 3) Operating Temperature Range 50 35 50 100 150 200 300 400 500 600 70 105 140 210 280 350 420 100 150 200 300 400 500 600 Units V V V I(AV) 10.0 A IFSM 150 A VF 0.975 IR 1.3 1.7 10 400 35 170 140 4 -65 to +150 Storage Temperature Range TSTG -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mounted on Heatsink. Size (2” x 3” x 0.25”) Al-plate. - 270 - V uA uA nS pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (SFAF1001G THRU SFAF1008G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm 8 6 4 2 0 50 100 150 o FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT TJ=100 0C 100 TJ=75 0C 10 1 TJ=25 0C 250 Tj=25 0C 200 0.1 8.3ms Single Half Sine Wave JEDEC Method 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 150 FIG.6- TYPICAL FORWARD CHARACTERISTICS 100 100 50 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL JUNCTION CAPACITANCE 300 Tj=25 0C 250 200 SF AF 150 SF AF 1 100 01 00 G~ SF AF 5G ~S FA F1 0 50 0 10 10 04 G 2 5 10 G 20 10 3 1 G 05 10 AF SF G 08 10 F FA ~S G 07 10 AF SF 0.3 0.1 0.01 0.4 50 G 06 10 F FA ~S 0.03 08 1 30 SF AF 10 01 G~ SF AF 10 04 G PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) INSTANTANEOUS REVERSE CURRENT. ( A) 1000 0 CAPACITANCE.(pF) FIG.3- TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE SET TIME BASE FOR 5/ 10ns/ cm 100 200 500 1000 REVERSE VOLTAGE. (V) - 271- Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) 1.6 1.8