SFD601G THRU SFD608G 6.0 AMPS. Glass Passivated Super Fast Rectifiers Voltage Range 50 to 600 Volts Current 6.0 Amperes DPAK Features .093(2.35) .089(2.25) .211(5.36) .207(5.26) Marking .043(1.10) .035(0.90) 0 5 0 5 Mechanical Data 30 .112(2.85) .092(2.35) .059(1.45) .039(0.95) .053(1.30) .045(1.10) .211(5.36) .207(5.26) .165(4.20) .149(3.80) .031(0.80) Case: Epoxy molded Epoxy: UL 94V-O rate flame retardant Terminals: Leads solderable per MIL-STD202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260oC/10 seconds. Weight: 0.4 grams 5 .013(0.54) .011(0.48) .024(0.60) .013(0.54) .011(0.48) .384(9.75) .364(9.25) Ultrafast Recovery Low forward voltage drop High current capability High reliability High surge current capability .274(6.95) .270(6.85) .250(6.55) .246(6.45) .250(6.55) .246(6.45) 1 2 3 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol SFD SFD SFD SFD Type Number SFD SFD SFD SFD 601G 602G 603G 604G 605G 606G 607G 608G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 137℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @3.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ VRRM VRMS VDC A IFSM 50 A 1.1 VF TSTG 1.3 1.7 5.0 200 35 9.0 IR Storage Temperature Range Typical Junction Capacitance (Note 2) V V V 6.0 Operating Temperature Range Typical Thermal Resistance (Note 3) 100 150 200 300 400 500 600 70 105 140 210 280 350 420 100 150 200 300 400 500 600 I(AV) Trr RθJC Cj TJ Maximum Reverse Recovery Time(Note1) 50 35 50 Units 50 -65 to +150 -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Thermal Resistance from Junction to Case. - 258 - 30 V µA µA nS ℃/W pF ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (SFD601G THRU SFD608G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm FIG.3- TYPICAL REVERSE CHARACTERISTICS 1000 8 6 4 2 0 0 50 100 150 o FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG TJ=100 0C 10 TJ=25 0C 1 50 TJ=125 0C 40 0.1 8.3ms Single Half Sine Wave JEDEC Method 0 20 40 60 80 100 120 140 30 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 20 FIG.6- TYPICAL FORWARD CHARACTERISTICS PER LEG 100 20 50 100 FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG 60 Tj=25 0C 50 40 SF 30 SF 20 10 0 1 2 D6 D6 05 01G ~S G~ SF 5 D6 FD 604 G 20 SF 3 50 100 200 500 1000 REVERSE VOLTAGE. (V) - 259 - D6 05 SF 1 S G~ D6 FD 07 G 60 ~S 6G FD 60 8G 0.3 0.1 0.01 0.4 10 60 10 0.03 G 08 30 FD 10 ~S 5 1G 2 60 1 D 0 4G 10 NUMBER OF CYCLES AT 60Hz CAPACITANCE.(pF) 100 SF PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) INSTANTANEOUS REVERSE CURRENT. ( A) 10 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE SET TIME BASE FOR 5/ 10ns/ cm Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) 1.6 1.8