AWT6130 Cellular Dual Mode AMPS/CDMA 3.5V 29dBm Power Amplifier Module PRELIMINARY DATA SHEET - Rev 1.0 FEATURES • InGaP HBT Technology • High Efficiency: 48% AMPS, 37% CDMA • Low Quiescent Current: 50 mA • Low Leakage Current in Shutdown Mode: <1 µA • Optimized for a 50 Ω System • Low Profile Miniature Surface Mount Package • CDMA 1XRTT Compliant • CDMA 1xEV-DO Compliant APPLICATIONS • Single Mode CDMA Wireless Handsets • Dual Mode AMPS/CDMA Wireless Handsets • Tri Mode CDMA Handsets with GPS M7 Package 10 Pin 4mm x 4mm Surface Mount Module PRODUCT DESCRIPTION The AWT6130 provides the additional output power margin RF designers need to overcome additional post-PA insertion loss in tri-mode handset designs supporting E911 (GPS enabled). The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, increase handset talk and standby time. The self-contained 4mm x 4mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. GND at slug (pad) VREF 10 GND 1 VMODE 2 9 GND GND 3 8 RFOUT RFIN 4 7 GND VCC 5 6 VCC Bias Control Figure 1: Block Diagram 06/2003 AWT6130 GND VREF 1 10 GND VMODE 2 9 GND GND 3 8 RFOUT RFIN 4 7 GND VCC 5 6 VCC GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VREF Reference Voltage 2 VMODE Mode Control Voltage 3 GND Ground 4 RFIN RF Input 5 V CC Supply Voltage 6 V CC Supply Voltage 7 GND Ground 8 RFOUT RF Output 9 GND Ground 10 GND Ground PRELIMINARY DATA SHEET Rev 1.0 06/2003 AWT6130 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC) 0 +5 V Mode Control Voltage (VMODE) 0 +3.5 V Reference Voltage (VREF) 0 +3.5 V RF Input Power (PIN) - +10 dB m -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 824 - 849 MHz Supply Voltage (VCC) +3.2 +3.5 +4.2 V Reference Voltage (VREF) +2.8 0 +2.9 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.5 0 +2.9 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) +31.5 +29.0 - - dB m Case Temperature (TC) -30 - +85 °C AMPS, VCC = +3.5 V CDMA, VCC = +3.5 V The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. PRELIMINARY DATA SHEET Rev 1.0 06/2003 3 AWT6130 Table 4: Electrical Specifications - AMPS Operation (TC = +25 °C, VCC = +3.5 V, VREF = +2.9 V, VMODE = +2.9 V, POUT = +31.5 dBm, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain 25.5 28 30 dB - 0.3 1.0 dB Power-Added Efficiency 44 48 - % Quiescent Current (Icq) - 50 65 mA Reference Current - 3 5 mA through VREF pin Mode Control Current - 0.3 0.5 mA through VMODE pin Leakage Current - <1 5 µA VCC = +4.2 V, VREF = 0 V VMODE = 0 V Noise in Receive Band - -135 -133 Harmonics 2fo 3fo, 4fo - -40 -50 -30 -30 dB c Input Impedance - - 2:1 VSWR Gain Variation Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure 4 COMMENTS dBm/Hz 869 MHz to 894 MHz - - -70 dB c 8:1 - - VSWR PRELIMINARY DATA SHEET Rev 1.0 06/2003 POUT < +31.5 dBm In-band load VSWR < 8:1 Out-of-band load VSWR < 10:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range AWT6130 Table 5: Electrical Specifications - CDMA Operation (TC = +25 °C, VCC = +3.5 V, VREF = +2.9 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain 25.5 - 28 26 30 - dB POUT = +29 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.9 V Adjacent Channel Power at ±885 kHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -50 -50 -46.5 -46.5 dB c POUT = +29 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.9 V Adjacent Channel Power at ±1.98 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -59 -65 -56 -57 dB c POUT = +29 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.9 V Power-Added Efficiency 34 6.5 37.5 7.5 - % POUT = +29 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.9 V Quiescent Current (Icq) - 50 65 mA VMODE = +2.9 V Reference Current - 3 5 mA through VREF pin Mode Control Current - 0.3 0.5 mA through VMODE pin Leakage Current - <1 5 µA VCC = +4.2 V, VREF = 0 V VMODE = 0 V Noise in Receive Band - -135 -133 Harmonics 2fo 3fo, 4fo - -40 -50 -30 -30 dB c Input Impedance - - 2:1 VSWR Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure COMMENTS dBm/Hz 869 MHz to 894 MHz - - -70 dB c 8:1 - - VSWR PRELIMINARY DATA SHEET Rev 1.0 06/2003 POUT < +29 dBm In-band load VSWR < 8:1 Out-of-band load VSWR < 10:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range 5 AWT6130 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. Table 6: Bias Control POUT LE V E LS BIAS MODE V R EF VMODE (all) Low +2.9 V +2.9 V CDMA - low power <+16dBm Low +2.9 V +2.9 V CDMA - high power >+16 dBm High +2.9 V 0V - Shutdown 0V 0V APPLICATION AMPS Shutdown 6 PRELIMINARY DATA SHEET Rev 1.0 06/2003 AWT6130 PACKAGE OUTLINE Figure 3: M7 Package Outline - 10 Pin 4mm x 4mm Surface Mount Module PRELIMINARY DATA SHEET Rev 1.0 06/2003 7 AWT6130 ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 PRELIMINARY DATA SHEET Rev 1.0 06/2003