ANADIGICS AWT6302RM9Q7

AWT6302R
PCS/CDMA 3.4V/28dBm
Linear Power Amplifier Module
Data Sheet - Rev 2.1
FEATURES
• InGaP HBT Technology
• High Efficiency:
39%, VMODE = 0 V
40%, VMODE = +2.85 V (no mode switching)
• Low Quiescent Current: 50 mA
• Low Leakage Current in Shutdown Mode: <1 µA
• VREF = +2.85 V (+2.75 V min over temp)
• Optimized for a 50 Ω System
• Low Profile Miniature Surface Mount Package:
1.1 mm
• CDMA 1XRTT, 1xEV-DO Compliant
• Pinout Enables Easy Phone Board Migration
From 4 mm x 4 mm Package
M9 Package
8 Pin 3 mm x 3 mm x 1.1 mm
Surface Mount Module
• RoHS-Compliant Package, 250 oC MSL-3
APPLICATIONS
• CDMA/EVDO PCS-band Wireless Handsets and
Data Devices
PRODUCT DESCRIPTION
The AWT6302R meets the increasing demands for
higher efficiency and linearity in CDMA 1X handsets,
while reducing pcb area by 44%. The package pinout
was chosen to enable handset manufacturers to
switch from a 4 mm x 4 mm PA module with very few
layout changes to the phone board. The PA module is
optimized for VREF = +2.85 V. The device is manufactured
on an advanced InGaP HBT MMIC technology offering
state-of-the-art reliability, temperature stability, and
ruggedness. Selectable bias modes that optimize
efficiency for different output power levels, and a
shutdown mode with low leakage current, increase
handset talk and standby time. The self-contained
3 mm x 3 mm x 1.1 mm surface mount package
incorporates matching networks optimized for output
power, efficiency, and linearity in a 50 Ω system.
GND at slug (pad)
1
8
VCC
RFIN 2
7
RFOUT
6
GND
5
GND
VCC
VMODE 3
Bias Control
VREF 4
Figure 1: Block Diagram
09/2008
AWT6302R
GND
VCC
1
8
VCC
RFIN
2
7
RFOUT
VMODE
3
6
GND
VREF
4
5
GND
GND
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
2
PIN
NAME
DESCRIPTION
1
VCC
Supply Voltage
2
RFIN
RF Input
3
VMODE
Mode Control Voltage
4
VREF
Reference Voltage
5
GND
Ground
6
GND
Ground
7
RFOUT
RF Output
8
VCC
Supply Voltage
Data Sheet - Rev 2.1
09/2008
AWT6302R
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
MAX
UNIT
Supply Voltage (VCC)
0
+5
V
Mode Control Voltage (VMODE)
0
+3.5
V
Reference Voltage (VREF)
0
+3.5
V
RF Input Power (PIN)
-
+10
dBm
-40
+150
°C
Storage Temperature (TSTG)
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure
to absolute ratings for extended periods of time may adversely affect
reliability.
Table 3: Operating Ranges
PARAMETER
MIN
TYP
MAX
UNIT
Operating Frequency (f)
1850
-
1910
MHz
Supply Voltage (VCC)
+3.2
+3.4
+4.2
V
Reference Voltage (VREF)
+2.75
0
+2.85
-
+3.1
+0.5
V
PA "on"
PA "shut down"
Mode Control Voltage (VMODE)
+2.5
0
+2.85
-
+3.1
+0.5
V
Low Bias Mode
High Bias Mode
+28.0
-
dBm
-
+85
°C
RF Output Power (POUT)
27.5
Case Temperature (TC)
-30
(1)
COMMENTS
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
over the conditions defined in the electrical specifications.
Notes:
(1) For operation at Vcc = +3.2 V, Pout is derated by 0.5 dB.
Data Sheet - Rev 2.1
09/2008
3
AWT6302R
Table 4: Electrical Specifications
(TC = +25 °C, VCC = +3.4 V, VREF = +2.85 V, 50 Ω system)
PARAMETER
MIN
TYP
MAX
UNIT
Gain
24.5
22
26.5
24.5
29
27
dB
POUT = +28 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.85 V
Adjacent Channel Power
at +1.25 MHz offset
Primary Channel BW =1.23 MHz
Adjacent Channel BW = 30 kHz
-
-51
-51
-47
-47
dBc
POUT = +28 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.85 V
Adjacent Channel Power
at +2.25 MHz offset
Primary Channel BW =1.23 MHz
Adjacent Channel BW = 30 kHz
-
-63
-69
-57
-57
dBc
POUT = +28 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.85 V
Power-Added Efficiency
37
8.3
39
9
-
%
POUT = +28 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.85 V
Quiescent Current (Icq)
-
50
62
mA
VMODE = +2.85 V
Reference Current
-
2.3
4
mA
through VREF pin, PA "on"
Mode Control Current
-
0.3
1.0
mA
through VMODE pin, VMODE = +2.85 V
Leakage Current
-
<1
5
µA
VCC = +4.2 V, VREF = 0 V,
VMODE = 0 V
Noise in Receive Band
-
-132
-130
Harmonics
2fo
3fo, 4fo
-
-40
-55
-30
-30
dBc
Input Impedance
-
-
2.5:1
VSWR
Spurious Output Level
(all spurious outputs)
Load mismatch stress with no
permanent degradation or failure
dBm/Hz 1930 MHz to 1990 MHz
-
-
-65
dBc
POUT < +28 dBm
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating ranges
8:1
-
-
VSWR
Applies over full operating range
Notes:
1. ACPRs and Efficiency Limits at mid-band only.
4
COMMENTS
Data Sheet - Rev 2.1
09/2008
AWT6302R
Table 5: Electrical Specifications
(TC = +25 °C, VCC = +3.4 V, VREF = +2.85 V, VMODE = +2.85 V, 50 Ω system)
PARAMETER
MIN
TYP
MAX
UNIT
24
22
26
24.5
28
27
dB
POUT = +28 dBm
POUT = +16 dBm
Adjacent Channel Power
at +1.25 MHz offset
Primary Channel BW - 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-52
-51
-47
-47
dBc
POUT = +28 dBm
POUT = +16 dBm
Adjacent Channel Power
at +2.25 MHz offset
Primary Channel BW - 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-61
-69
-57
-57
dBc
POUT = +28 dBm
POUT = +16 dBm
Power-Added Efficiency
37
8.3
40
9
-
%
POUT = +28 dBm
POUT = +16 dBm
Quiescent Current (Icq)
-
48
62
mA
VMODE = +2.85 V
Reference Current
-
2.3
4
mA
through VREF pin, PA "on"
Mode Control Current
-
0.3
1.0
mA
through VMODE pin
Leakage Current
-
<1
5
µA
VCC = +4.2 V, VREF = 0 V,
VMODE = 0 V
Noise in Receive Band
-
-132
-130
Harmonics
2fo
3fo, 4fo
-
-40
-55
-30
-30
dBc
Input Impedance
-
-
2.5:1
VSWR
Gain
Spurious Output Level
(all spurious outputs)
Load mismatch stress with no
permanent degradation or failure
COMMENTS
dBm/Hz 1930 MHz to 1990 MHz
-
-
-65
dBc
POUT < +28 dBm
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating ranges
8:1
-
-
VSWR
Applies over full operating range
Notes:
1. ACPRs and Efficiency Limits at mid-band only.
Data Sheet - Rev 2.1
09/2008
5
AWT6302R
APPLICATION INFORMATION
Bias Modes
The power amplifier may be placed in either a Low Bias
mode or a High Bias mode by applying the appropriate
logic level (see Operating Ranges table) to the VMODE
voltage. The Bias Control table lists the recommended
modes of operation for various applications.
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying logic low levels (see Operating
Ranges table) to both the VREF and VMODE voltages.
Table 6: Bias Control
APPLICATION
POUT
LEVELS
BIAS
MODE
CDMA - low power
<+16dBm
Low
+2.85 V +2.85 V
CDMA - high power
>+16 dBm
High
+2.85 V
0V
-
Shutdown
0V
0V
Shutdown
VREF
VMODE
VCC1
VCC2
C5
2.2µF
RF IN
VMODE
VREF
C1
1000 pF
1
VCC
2
RFIN
GND
at slug
VCC
RFOUT
8
7
3
VMODE
GND 6
4
V REF
GND 5
C2
0.01µF
Figure 3: Application Circuit
6
C3
1000 pF
Data Sheet - Rev 2.1
09/2008
C6
68 pF
C4
2.2 µF
RF OUT
AWT6302R
PACKAGE OUTLINE
Figure 4: M9 Package Outline - 8 Pin 3 mm x 3 mm x 1.1 mm Surface Mount Module
6302R
LLLLNN
BBBBCC
Figure 5: Branding Specification
Data Sheet - Rev 2.1
09/2008
7
AWT6302R
COMPONENT PACKAGING
Figure 6: Tape & Reel Packaging
Table 7: Tape & Reel Dimensions
8
PACKAGE TYPE
TAPE WIDTH
POCKET PITCH
REEL CAPACITY
MAX REEL DIA
3 mm x 3 mm x 1 mm
12 mm
4 mm
2500
7"
Data Sheet - Rev 2.1
09/2008
AWT6302R
NOTES
Data Sheet - Rev 2.1
09/2008
9
AWT6302R
ORDERING INFORMATION
ORDER NUMBER
AWT6302RM9Q7
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
COMPONENT PACKAGING
-30 °C to +85 °C
RoHS-Compliant
8 Pin
3 mm x 3 mm x 1 mm
Surface Mount Module
Tape and Reel, 2500 pieces per Reel
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: [email protected]
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers
to verify that the information they are using is current before placing orders.
warning
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product
in any such application without written consent is prohibited.
10
Data Sheet - Rev 2.1
09/2008