FREESCALE MPC8309EC

Freescale Semiconductor
Document Number: MPC8309EC
Rev. 0, 03/2011
Technical Data
MPC8309
PowerQUICC II Pro Integrated
Communications Processor
Family Hardware Specifications
This document provides an overview of the MPC8309
PowerQUICC II Pro processor features. The MPC8309 is a
cost-effective, highly integrated communications processor
that addresses the requirements of several networking
applications, including residential gateways,
modem/routers, industrial control, and test and measurement
applications. The MPC8309 extends current PowerQUICC
offerings, adding higher CPU performance, additional
functionality, and faster interfaces, while addressing the
requirements related to time-to-market, price, power
consumption, and board real estate. This document describes
the electrical characteristics of MPC8309.
To locate published errata or updates for this document, refer
to the MPC8309 product summary page on our website
listed on the back cover of this document or contact your
local Freescale sales office.
© 2011 Freescale Semiconductor, Inc. All rights reserved.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 7
Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 11
Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . 14
DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ethernet and MII Management . . . . . . . . . . . . . . . . . 23
TDM/SI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
HDLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
eSDHC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
FlexCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
IPIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 53
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
System Design Information . . . . . . . . . . . . . . . . . . . 76
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 79
Document Revision History . . . . . . . . . . . . . . . . . . . 81
Overview
1
Overview
The MPC8309 incorporates the e300c3 (MPC603e-based) core built on Power Architecture® technology,
which includes 16 Kbytes of each L1 instruction and data caches, dual integer units, and on-chip memory
management units (MMUs). The MPC8309 also includes a 32-bit PCI controller, two DMA engines and
a 16/32-bit DDR2 memory controller with 8-bit ECC.
A new communications complex based on QUICC Engine technology forms the heart of the networking
capability of the MPC8309. The QUICC Engine block contains several peripheral controllers and a 32-bit
RISC controller. Protocol support is provided by the main workhorses of the device—the unified
communication controllers (UCCs). A block diagram of the MPC8309 is shown in Figure 1.
2x DUART
I2C
Timers
GPIO
SPI
RTC
e300c3 Core with Power
Management
16-KB
I-Cache
16-KB
D-Cache
ULPI
Interrupt
Controller
FPU
QUICC Engine™ Block
4 FlexCAN
IO
Sequencer
Enhanced
Local Bus
eSDHC
DDR2
Controller
DMA
Engine 2
16 KB Multi-User RAM
Accelerators
48 KB Instruction RAM
DMA
Engine 1
PCI Controller
UCC7
UCC5
UCC3
UCC2
Single 32-bit RISC CP Serial DMA
UCC1
Baud Rate
Generators
USB 2.0 HS
Host/Device/OTG
Time Slot Assigner
Serial Interface
2x TDM Ports
2x HDLC
2 RMII/MII
1 RMII/MII
2x IEEE 1588
Figure 1. MPC8309 Block Diagram
Each of the five UCCs can support a variety of communication protocols such as 10/100 Mbps Ethernet
and HDLC.
In summary, the MPC8309 provides users with a highly integrated, fully programmable communications
processor. This helps to ensure that a low-cost system solution can be quickly developed and offers
flexibility to accommodate new standards and evolving system requirements.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
2
Freescale Semiconductor
Overview
1.1
Features
The major features of the device are as follows:
• e300c3 Power Architecture processor core
— Enhanced version of the MPC603e core
— High-performance, superscalar processor core with a four-stage pipeline and low interrupt
latency times
— Floating-point, dual integer units, load/store, system register, and branch processing units
— 16-Kbyte instruction cache and 16-Kbyte data cache with lockable capabilities
— Dynamic power management
— Enhanced hardware program debug features
— Software-compatible with Freescale processor families implementing Power Architecture
technology
— Separate PLL that is clocked by the system bus clock
— Performance monitor
• QUICC Engine block
— 32-bit RISC controller for flexible support of the communications peripherals with the
following features:
– One clock per instruction
– Separate PLL for operating frequency that is independent of system’s bus and e300 core
frequency for power and performance optimization
– 32-bit instruction object code
– Executes code from internal IRAM
– 32-bit arithmetic logic unit (ALU) data path
– Modular architecture allowing for easy functional enhancements
– Slave bus for CPU access of registers and multiuser RAM space
– 48 Kbytes of instruction RAM
– 16 Kbytes of multiuser data RAM
– Serial DMA channel for receive and transmit on all serial channels
— Five unified communication controllers (UCCs) supporting the following protocols and
interfaces:
– 10/100 Mbps Ethernet/IEEE Std. 802.3® through MII and RMII interfaces.
– IEEE Std. 1588™ support
– HDLC/Transparent (bit rate up to QUICC Engine operating frequency / 8)
– HDLC Bus (bit rate up to 10 Mbps)
– Asynchronous HDLC (bit rate up to 2 Mbps)
– Two TDM interfaces supporting up to 128 QUICC multichannel controller channels, each
running at 64 kbps
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
3
Overview
•
•
•
For more information on QUICC Engine sub-modules, see QUICC Engine Block Reference
Manual with Protocol Interworking.
DDR SDRAM memory controller
— Programmable timing supporting DDR2 SDRAM
— Integrated SDRAM clock generation
— Supports 8-bit ECC
— 16/32-bit data interface, up to 333-MHz data rate
— 14 address lines
— The following SDRAM configurations are supported:
– Up to two physical banks (chip selects), 512-Mbyte addressable space for 32 bit data
interface64-Mbit to 2-Gbit devices with x8/x16/x32 data ports (no direct x4 support)
— One 16-bit device or two 8-bit devices on a 16-bit bus, or two 16-bit devices or four 8-bit
devices on a 32-bit busSupport for up to 16 simultaneous open pages for DDR2
— Two clock pair to support up to 4 DRAM devices
— Supports auto refresh
— On-the-fly power management using CKE
Enhanced local bus controller (eLBC)
— Multiplexed 26-bit address and 8-/16-bit data operating at up to 66 MHz
— Eight chip selects supporting eight external slaves
– Four chip selects dedicated
– Four chip selects offered as multiplexed option
— Supports boot from parallel NOR Flash and parallel NAND Flash
— Supports programmable clock ratio dividers
— Up to eight-beat burst transfers
— 16- and 8-bit ports, seperate LWE for each 8 bit
— Three protocol engines available on a per chip select basis:
– General-purpose chip select machine (GPCM)
– Three user programmable machines (UPMs)
– NAND Flash control machine (FCM)
— Variable memory block sizes for FCM, GPCM, and UPM mode
— Default boot ROM chip select with configurable bus width (8 or 16)
— Provides two Write Enable signals to allow single byte write access to external 16-bit eLBC
slave devices
Integrated programmable interrupt controller (IPIC)
— Functional and programming compatibility with the MPC8260 interrupt controller
— Support for external and internal discrete interrupt sources
— Programmable highest priority request
— Six groups of interrupts with programmable priority
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
4
Freescale Semiconductor
Overview
•
•
— External and internal interrupts directed to host processor
— Unique vector number for each interrupt source
PCI interface
— Designed to comply with PCI Local Bus Specification, Revision 2.3
— 32-bit PCI interface operating at up to 66 MHz
— PCI 3.3-V compatible
— Not 5-V compatible
— Support for host and agent modes
— Support for PCI-to-memory and memory-to-PCI streaming
— Memory prefetching of PCI read accesses and support for delayed read transactions
— Support for posting of processor-to-PCI and PCI-to-memory writes
— On-chip arbitration, supporting three masters on PCI
— Arbiter support for two-level priority request/grant signal pairs
— Support for accesses to all PCI address spaces
— Support for parity
— Selectable hardware-enforced coherency
— Address translation units for address mapping between host and peripheral
— Mapping from an external 32-/64-bit address space to the internal 32-bit local space
— Support for dual address cycle (DAC) (as a target only)
— Internal configuration registers accessible from PCI
— Selectable snooping for inbound transactions
— Four outbound Translation Address Windows
– Support for mapping 32-bit internal local memory space to an external 32-bit PCI address
space and translating that address within the PCI space
— Four inbound Translation Address Windows corresponding to defined PCI BARs
– The first BAR is 32-bits and dedicated to on-chip register access
– The second BAR is 32-bits for general use
– The remaining two BARs may be 32- or 64-bits and are also for general use
Enhanced secure digital host controller (eSDHC)
— Compatible with the SD Host Controller Standard Specification Version 2.0 with test event
register support
— Compatible with the MMC System Specification Version 4.2
— Compatible with the SD Memory Card Specification Version 2.0 and supports the high capacity
SD memory card
— Compatible with the SD Input/Output (SDIO) Card Specification, Version 2.0
— Designed to work with SD Memory, miniSD Memory, SDIO, miniSDIO, SD Combo, MMC,
MMCplus, and RS-MMC cards
— Card bus clock frequency up to 33.25 MHz.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
5
Overview
•
•
•
•
•
— Supports 1-/4-bit SD and SDIO modes, 1-/4-bit modes
– Up to 133 Mbps data transfer for SD/SDIO/MMC cards using 4 parallel data lines
— Supports block sizes of 1 ~ 4096 bytes
Universal serial bus (USB) dual-role controller
— Designed to comply with Universal Serial Bus Revision 2.0 Specification
— Supports operation as a stand-alone USB host controller
— Supports operation as a stand-alone USB device
— Supports high-speed (480-Mbps), full-speed (12-Mbps), and low-speed (1.5-Mbps) operations.
Low speed is only supported in host mode.
FlexCAN module
— Full implementation of the CAN protocol specification version 2.0B
— Up to 64 flexible message buffers of zero to eight bytes data length
— Powerful Rx FIFO ID filtering, capable of matching incoming IDs
— Selectable backwards compatibility with previous FlexCAN module version
— Programmable loop-back mode supporting self-test operation
— Global network time, synchronized by a specific message
— Independent of the transmission medium (an external transceiver is required)
— Short latency time due to an arbitration scheme for high-priority messages
Dual I2C interfaces
— Two-wire interface
— Multiple-master support
— Master or slave I2C mode support
— On-chip digital filtering rejects spikes on the bus
— I2C1 can be used as the boot sequencer
DMA Engine1
— Support for the DMA engine with the following features:
– Sixteen DMA channels
– All data movement via dual-address transfers: read from source, write to destination
– Transfer control descriptor (TCD) organized to support two-deep, nested transfer operations
– Channel activation via one of two methods (for both the methods, one activation per
execution of the minor loop is required):
– Explicit software initiation
– Initiation via a channel-to-channel linking mechanism for continuous transfers
(independent channel linking at end of minor loop and/or major loop)
– Support for fixed-priority and round-robin channel arbitration
– Channel completion reported via optional interrupt requests
— Support for scatter/gather DMA processing
IO Sequencer
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
6
Freescale Semiconductor
Electrical Characteristics
•
•
•
•
•
•
•
•
2
Direct memory access (DMA) controller (DMA Engine 2)
— Four independent fully programmable DMA channels
— Concurrent execution across multiple channels with programmable bandwidth control
— Misaligned transfer capability for source/destination address
— Data chaining and direct mode
— Interrupt on completed segment, error, and chain
DUART
— Supports 2 DUART
— Each has two2-wire interfaces (RxD, TxD)
– The same can be configured as one 4-wire interface (RxD, TxD, RTS, CTS)
— Programming model compatible with the original 16450 UART and the PC16550D
Serial peripheral interface (SPI)
— Master or slave support
Power management controller (PMC)
— Supports core doze/nap/sleep/ power management
— Exits low power state and returns to full-on mode when
– The core internal time base unit invokes a request to exit low power state
– The power management controller detects that the system is not idle and there are
outstanding transactions on the internal bus or an external interrupt.
Parallel I/O
— General-purpose I/O (GPIO)
– 56 parallel I/O pins multiplexed on various chip interfaces
– Interrupt capability
System timers
— Periodic interrupt timer
— Software watchdog timer
— Eight general-purpose timers
Real time clock (RTC) module
— Maintains a one-second count, unique over a period of thousand of years
— Two possible clock sources:
– External RTC clock (RTC_PIT_CLK)
– CSB bus clock
IEEE Std. 1149.1™ compliant JTAG boundary scan
Electrical Characteristics
This section provides the AC and DC electrical specifications and thermal characteristics for the
MPC8309. The MPC8309 is currently targeted to these specifications. Some of these specifications are
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
7
Electrical Characteristics
independent of the I/O cell, but are included for a more complete reference. These are not purely I/O buffer
design specifications.
2.1
Overall DC Electrical Characteristics
This section covers the ratings, conditions, and other characteristics.
2.1.1
Absolute Maximum Ratings
Table 1 provides the absolute maximum ratings.
Table 1. Absolute Maximum Ratings1
Characteristic
Symbol
Max Value
Unit
Notes
Core supply voltage
VDD
–0.3 to 1.26
V
—
PLL supply voltage
AVDD1
AVDD2
AVDD3
–0.3 to 1.26
V
—
DDR2 DRAM I/O voltage
GVDD
–0.3 to 1.98
V
—
PCI, Local bus, DUART, system control and power management,
I2C, SPI, MII, RMII, MII management, eSDHC, FlexCAN,USB and
JTAG I/O voltage
OVDD
–0.3 to 3.6
V
2
Input voltage
MVIN
–0.3 to (GVDD + 0.3)
V
3
MVREF
–0.3 to (GVDD + 0.3)
V
3
Local bus, DUART, SYS_CLK_IN,
system control and power
management, I2C, SPI, and JTAG
signals
OVIN
–0.3 to (OVDD + 0.3)
V
4
PCI
OVIN
–0.3 to (OVDD + 0.3)
V
TSTG
–55 to 150
C
DDR2 DRAM signals
DDR2 DRAM reference
Storage temperature range
—
Notes:
1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
2. OVDD here refers to NVDDA, NVDDB,NVDDC, NVDDF, NVDDG, and NVDDH from the ball map.
3. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 100 ms during
power-on reset and power-down sequences.
4. Caution: OVIN must not exceed OVDD by more than 0.3 V. This limit may be exceeded for a maximum of 100 ms during
power-on reset and power-down sequences.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
8
Freescale Semiconductor
Electrical Characteristics
2.1.2
Power Supply Voltage Specification
Table 2 provides the recommended operating conditions for the MPC8309. Note that these values are the
recommended and tested operating conditions. Proper device operation outside of these conditions is not
guaranteed.
Table 2. Recommended Operating Conditions
Symbol
Recommended
Value
Unit
Notes
Core supply voltage
VDD
1.0 V ± 50 mV
V
1
PLL supply voltage
AVDD1
AVDD2
AVDD3
1.0 V ± 50 mV
V
1
DDR2 DRAM I/O voltage
GVDD
1.8 V ± 100 mV
V
1
PCI, Local bus, DUART, system control and power management,
I2C, SPI, MII, RMII, MII management, eSDHC, FlexCAN,USB and
JTAG I/O voltage
OVDD
3.3 V ± 300 mV
V
1, 3
Junction temperature
TA/TJ
0 to 105
C
2
Characteristic
Note:
1. GVDD, OVDD, AVDD, and VDD must track each other and must vary in the same direction—either in the positive or negative
direction.
2. Minimum temperature is specified with TA(Ambient Temperature); maximum temperature is specified with TJ(Junction
Temperature).
3. OVDD here refers to NVDDA, NVDDB,NVDDC, NVDDF, NVDDG, and NVDDH from the ball map.
Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8309
G/OVDD + 20%
G/OVDD + 5%
VIH
G/OVDD
GND
GND – 0.3 V
VIL
GND – 0.7 V
Not to Exceed 10%
of tinterface1
Note:
1. tinterface refers to the clock period associated with the bus clock interface.
Figure 2. Overshoot/Undershoot Voltage for GVDD/OVDD
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
9
Electrical Characteristics
2.1.3
Output Driver Characteristics
Table 3 provides information on the characteristics of the output driver strengths.
Table 3. Output Drive Capability
Output Impedance
()
Supply Voltage (V)
Local bus interface utilities signals
42
OVDD = 3.3
PCI Signal
25
DDR2 signal
18
GVDD = 1.8
DUART, system control, I2C, SPI, JTAG
42
OVDD = 3.3
GPIO signals
42
OVDD = 3.3
Driver Type
2.1.4
Input Capacitance Specification
Table 4 describes the input capacitance for the SYS_CLK_IN pin in the MPC8309.
Table 4. Input Capacitance Specification
Parameter/Condition
Input capacitance for all pins except SYS_CLK_IN and
QE_CLK_IN
Input capacitance for SYS_CLK_IN and QE_CLK_IN
Symbol
Min
Max
Unit
Notes
CI
6
8
pF
—
CICLK_IN
10
—
pF
1
Note:
1. The external clock generator should be able to drive 10 pF.
2.2
Power Sequencing
The device does not require the core supply voltage (VDD) and IO supply voltages (GVDD and OVDD) to
be applied in any particular order. Note that during power ramp-up, before the power supplies are stable
and if the I/O voltages are supplied before the core voltage, there might be a period of time that all input
and output pins are actively driven and cause contention and excessive current. In order to avoid actively
driving the I/O pins and to eliminate excessive current draw, apply the core voltage (VDD) before the I/O
voltage (GVDD and OVDD) and assert PORESET before the power supplies fully ramp up. In the case
where the core voltage is applied first, the core voltage supply must rise to 90% of its nominal value before
the I/O supplies reach 0.7 V; see Figure 3. Once both the power supplies (I/O voltage and core voltage) are
stable, wait for a minimum of 32 clock cycles before negating PORESET.
NOTE
There is no specific power down sequence requirement for the device. I/O
voltage supplies (GVDD and OVDD) do not have any ordering requirements
with respect to one another.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
10
Freescale Semiconductor
Power Characteristics
I/O Voltage (GVDD and OVDD)
V
Core Voltage (VDD)
0.7 V
90%
t
0
PORESET
>= 32  tSYS_CLK_IN
Figure 3. MPC8309 Power-Up Sequencing Example
3
Power Characteristics
The typical power dissipation for this family of MPC8309 devices is shown in Table 5.
Table 5.
MPC8309 Power Dissipation
Core
Frequency (MHz)
QUICC Engine
Frequency (MHz)
CSB
Frequency (MHz)
Typical
Maximum
Unit
Notes
266
200
133
0.341
0.920
W
1, 2,3
333
200
133
0.361
0.938
W
1,2,3
400
200
133
0.381
0.969
W
1,2,3
417
233
167
0.429
1.003
W
1,2,3
Notes:
1. The values do not include I/O supply power (OVDD and GVDD), but it does include VDD and AVDD power . For I/O power
values, see Table 6.
2. Typical power is based on a nominal voltage of VDD = 1.0 V, ambient temperature, and the core running a Dhrystone
benchmark application. The measurements were taken on the evaluation board using WC process silicon.
3. Maximum power is based on a voltage of VDD = 1.05 V, WC process, a junction TJ = 105C, and an smoke test code.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
11
Power Characteristics
Table 6 shows the estimated typical I/O power dissipation for the device.
Table 6. Typical I/O Power Dissipation
Interface
Parameter
DDR I/O
65% utilization
1.8 V
Rs = 20 
Rt = 50 
1 pair of clocks
266 MHz, 1  16 bits
Local bus I/O load = 25 pF
1 pair of clocks
66 MHz, 26 bits
QUICC Engine block and other I/Os
TDM serial, HDLC/TRAN
serial, DUART, MII, RMII,
Ethernet management,
USB, PCI, SPI ,
Timer output
FlexCAN
eSDHC
GVDD
(1.8 V)
OVDD
(3.3 V)
Unit
Comments
—
W
—
0.415
W
1
0.149
—
Note:
1. Typical IO power is based on a nominal voltage of VDD = 3.3V, ambient temperature, and the core running a Dhrystone
benchmark application. The measurements were taken on the evaluation board using WC process silicon.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
12
Freescale Semiconductor
Clock Input Timing
4
Clock Input Timing
This section provides the clock input DC and AC electrical characteristics for the MPC8309.
NOTE
The rise/fall time on QUICC Engine input pins should not exceed 5 ns. This
should be enforced especially on clock signals. Rise time refers to signal
transitions from 10% to 90% of OVDD; fall time refers to transitions from
90% to 10% of OVDD.
4.1
DC Electrical Characteristics
Table 7 provides the clock input (SYS_CLK_IN/PCI_SYNC_IN) DC specifications for the MPC8309.
These specifications are also applicable for QE_CLK_IN.
Table 7. SYS_CLK_IN DC Electrical Characteristics
Parameter
Condition
Symbol
Min
Max
Unit
Input high voltage
—
VIH
2.4
OVDD + 0.3
V
Input low voltage
—
VIL
–0.3
0.4
V
SYS_CLK_IN input current
0 V  VIN  OVDD
IIN
—
±5
A
SYS_CLK_IN input current
0 V  VIN  0.5 V or
OVDD – 0.5 V  VIN OVDD
IIN
—
±5
A
SYS_CLK_IN input current
0.5 V  VIN  OVDD – 0.5 V
IIN
—
±50
A
4.2
AC Electrical Characteristics
The primary clock source for the MPC8309 can be one of two inputs, SYS_CLK_IN or PCI_SYNC_IN,
depending on whether the device is configured in PCI host or agent mode. Table 8 provides the clock input
(SYS_CLK_IN/PCI_SYNC_IN) AC timing specifications for the MPC8309. These specifications are also
applicable for QE_CLK_IN.
Table 8. SYS_CLK_IN AC Timing Specifications
Parameter/Condition
Symbol
Min
Typical
Max
Unit
Notes
SYS_CLK_IN frequency
fSYS_CLK_IN
24
—
66.67
MHz
1
SYS_CLK_IN cycle time
tSYS_CLK_IN
15
—
41.6
ns
—
SYS_CLK_IN rise and fall time
tKH, tKL
1.1
—
2.8
ns
2
PCI_SYNC_IN rise and fall time
tPCH, tPCL
1.1
—
2.8
ns
2
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
13
RESET Initialization
Table 8. SYS_CLK_IN AC Timing Specifications
SYS_CLK_IN duty cycle
tKHK/tSYS_CLK_
40
—
60
%
3
—
—
±150
ps
4, 5
IN
SYS_CLK_IN jitter
—
Notes:
1. Caution: The system, core and QUICC Engine block must not exceed their respective maximum or minimum operating
frequencies.
2. Rise and fall times for SYS_CLK_IN are measured at 0.33 and 2.97 V.
3. Timing is guaranteed by design and characterization.
4. This represents the total input jitter—short term and long term—and is guaranteed by design.
5. The SYS_CLK_IN driver’s closed loop jitter bandwidth should be < 500 kHz at –20 dB. The bandwidth must be set low to
allow cascade-connected PLL-based devices to track SYS_CLK_IN drivers with the specified jitter.
6. Spread spectrum is allowed upto 1% down-spread @ 33kHz (max rate).
5
RESET Initialization
This section describes the AC electrical specifications for the reset initialization timing requirements of
the MPC8309. Table 9 provides the reset initialization AC timing specifications for the reset
component(s).
Table 9. RESET Initialization Timing Specifications
Parameter/Condition
Min
Max
Unit
Notes
Required assertion time of HRESET to activate reset flow
32
—
tSYS_CLK_IN
1
Required assertion time of PORESET with stable clock applied to
SYS_CLK_IN or PCI_SYNC_IN (in agent mode)
32
—
tSYS_CLK_IN
1
HRESET assertion (output)
512
—
tSYS_CLK_IN
1
Input setup time for POR configuration signals
(CFG_RESET_SOURCE[0:3]) with respect to negation of PORESET
4
—
tSYS_CLK_IN
1, 2
Input hold time for POR config signals with respect to negation of
HRESET
0
—
ns
1, 2
Notes:
1. tSYS_CLK_IN is the clock period of the input clock applied to SYS_CLK_IN. For more details, see the MPC8309
PowerQUICC II Pro Integrated Communications Processor Reference Manual.
2. POR configuration signals consists of CFG_RESET_SOURCE[0:3].
Table 10 provides the PLL lock times.
Table 10. PLL Lock Times
Parameter/Condition
PLL lock times
5.1
Min
Max
Unit
Notes
—
100
s
—
Reset Signals DC Electrical Characteristics
Table 11 provides the DC electrical characteristics for the MPC8309 reset signals mentioned in Table 9.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
14
Freescale Semiconductor
DDR2 SDRAM
Table 11. Reset Signals DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Notes
Output high voltage
VOH
IOH = –6.0 mA
2.4
—
V
1
Output low voltage
VOL
IOL = 6.0 mA
—
0.5
V
1
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
1
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
1
Input low voltage
VIL
—
–0.3
0.8
V
—
Input current
IIN
0 V  VIN  OVDD
—
±5
A
—
Note:
1. This specification applies when operating from 3.3 V supply.
6
DDR2 SDRAM
This section describes the DC and AC electrical specifications for the DDR2 SDRAM interface of the
MPC8309. Note that DDR2 SDRAM is GVDD(typ) = 1.8 V.
6.1
DDR2 SDRAM DC Electrical Characteristics
Table 12 provides the recommended operating conditions for the DDR2 SDRAM component(s) of the
MPC8309 when GVDD(typ) = 1.8 V.
Table 12. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
GVDD
1.7
1.9
V
1
MVREF
0.49  GVDD
0.51  GVDD
V
2
I/O termination voltage
VTT
MVREF – 0.04
MVREF + 0.04
V
3
Input high voltage
VIH
MVREF+ 0.125
GVDD + 0.3
V
—
Input low voltage
VIL
–0.3
MVREF – 0.125
V
—
Output leakage current
IOZ
–9.9
9.9
A
4
Output high current (VOUT = 1.35 V)
IOH
–13.4
—
mA
—
Output low current (VOUT = 0.280 V)
IOL
13.4
—
mA
—
I/O supply voltage
I/O reference voltage
Notes:
1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.
2. MVREF is expected to be equal to 0.5  GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak
noise on MVREF may not exceed ±2% of the DC value.
3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be
equal to MVREF. This rail should track variations in the DC level of MVREF.
4. Output leakage is measured with all outputs disabled, 0 V  VOUT GVDD.
Table 13 provides the DDR2 capacitance when GVDD(typ) = 1.8 V.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
15
DDR2 SDRAM
Table 13. DDR2 SDRAM Capacitance for GVDD(typ) = 1.8 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
Input/output capacitance: DQ, DQS
CIO
6
8
pF
1
Delta input/output capacitance: DQ, DQS
CDIO
—
0.5
pF
1
Note:
1. This parameter is sampled. GVDD = 1.8 V ± 0.100 V, f = 1 MHz, TA = 25 °C, VOUT = GVDD  2,
VOUT (peak-to-peak) = 0.2 V.
6.2
DDR2 SDRAM AC Electrical Characteristics
This section provides the AC electrical characteristics for the DDR2 SDRAM interface.
6.2.1
DDR2 SDRAM Input AC Timing Specifications
Table 14 provides the input AC timing specifications for the DDR2 SDRAM (GVDD(typ) = 1.8 V).
Table 14. DDR2 SDRAM Input AC Timing Specifications for 1.8-V Interface
At recommended operating conditions with GVDD of 1.8 V± 100mV.
Parameter
Symbol
Min
Max
Unit
Notes
AC input low voltage
VIL
—
MVREF – 0.25
V
—
AC input high voltage
VIH
MVREF + 0.25
—
V
—
Unit
Notes
ps
1, 2
Table 15 provides the input AC timing specifications for the DDR2 SDRAM interface.
Table 15. DDR2 SDRAM Input AC Timing Specifications
At recommended operating conditions with GVDD of 1.8V ± 100mV.
Parameter
Symbol
Controller skew for MDQS—MDQ/MDM
Min
Max
–750
750
tCISKEW
266 MHz
Notes:
1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any corresponding bit that
is captured with MDQS[n]. This should be subtracted from the total timing budget.
2. The amount of skew that can be tolerated from MDQS to a corresponding MDQ signal is called tDISKEW. This can be
determined by the equation: tDISKEW = ±(T/4 – abs(tCISKEW)) where T is the clock period and abs(tCISKEW) is the absolute
value of tCISKEW.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
16
Freescale Semiconductor
DDR2 SDRAM
Figure 4 shows the input timing diagram for the DDR controller.
MCK[n]
MCK[n]
tMCK
MDQS[n]
MDQ[x]
D0
D1
tDISKEW
tDISKEW
Figure 4. DDR Input Timing Diagram
6.2.2
DDR2 SDRAM Output AC Timing Specifications
Table 16 provides the output AC timing specifications for the DDR2 SDRAM interfaces.
Table 16. DDR2 SDRAM Output AC Timing Specifications
At recommended operating conditions with GVDD of 1.8V ± 100mV.
Parameter
MCK cycle time, (MCK/MCK crossing)
ADDR/CMD output setup with respect to MCK
Symbol1
Min
Max
Unit
Notes
tMCK
5.988
8
ns
2
ns
3
2.4
2.5
—
ns
3
ns
3
ns
3
ns
4
tDDKHAS
333 MHz
266 MHz
ADDR/CMD output hold with respect to MCK
tDDKHAX
333 MHz
266 MHz
MCS output setup with respect to MCK
—
2.4
2.5
—
tDDKHCS
333 MHz
266 MHz
MCS output hold with respect to MCK
tDDKHCX
333 MHz
266 MHz
MCK to MDQS Skew
2.4
2.5
tDDKHMH
2.4
2.5
—
–0.6
0.6
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
17
DDR2 SDRAM
Table 16. DDR2 SDRAM Output AC Timing Specifications (continued)
At recommended operating conditions with GVDD of 1.8V ± 100mV.
Symbol1
Parameter
MDQ/MDM output setup with respect to MDQS
Max
tDDKHDS,
tDDKLDS
333 MHz
266 MHz
MDQ/MDM output hold with respect to MDQS
Min
0.8
0.9
Notes
ns
5
ps
5
—
tDDKHDX,
tDDKLDX
333 MHz
266 MHz
Unit
900
1100
—
MDQS preamble start
tDDKHMP
0.75 x tMCK
—
ns
6
MDQS epilogue end
tDDKHME
0.4 x tMCK
0.6 x tMCK
ns
6
Notes:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing
(DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example,
tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs
(A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference
(K) goes low (L) until data outputs (D) are invalid (X) or data output hold time.
2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.
3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MDM/MDQS. For the ADDR/CMD
setup and hold specifications, it is assumed that the Clock Control register is set to adjust the memory clocks by 1/2 applied
cycle.
4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD)
from the rising edge of the MCK(n) clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control
of the DQSS override bits in the TIMING_CFG_2 register. This is typically set to the same delay as the clock adjust in the
CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same
adjustment value. See the MPC8309 PowerQUICC II Pro Integrated Communications Processor Reference Manual for a
description and understanding of the timing modifications enabled by use of these bits.
5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), or data
mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor.
6. tDDKHMP follows the symbol conventions described in note 1.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
18
Freescale Semiconductor
DDR2 SDRAM
Figure 5 shows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH).
MCK
MCK
tMCK
tDDKHMH(max) = 0.6 ns
MDQS
tDDKHMH(min) = –0.6 ns
MDQS
Figure 5. Timing Diagram for tDDKHMH
Figure 6 shows the DDR2 SDRAM output timing diagram.
MCK[n]
MCK[n]
tMCK
tDDKHAS ,tDDKHCS
tDDKHAX ,tDDKHCX
ADDR/CMD
Write A0
NOOP
tDDKHMP
tDDKHMH
MDQS[n]
tDDKHME
tDDKHDS
tDDKLDS
MDQ[x]/
MECC[x]
D0
D1
tDDKLDX
tDDKHDX
Figure 6. DDR2 SDRAM Output Timing Diagram
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
19
Local Bus
7
Local Bus
This section describes the DC and AC electrical specifications for the local bus interface of the MPC8309.
7.1
Local Bus DC Electrical Characteristics
Table 17 provides the DC electrical characteristics for the local bus interface.
Table 17. Local Bus DC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
OVDD + 0.3
V
Low-level input voltage
VIL
–0.3
0.8
V
High-level output voltage, IOH = –100 A
VOH
OVDD – 0.2
—
V
Low-level output voltage, IOL = 100 A
VOL
—
0.2
V
IIN
—
±5
A
Input current
7.2
Local Bus AC Electrical Specifications
Table 18 describes the general timing parameters of the local bus interface of the MPC8309.
Table 18. Local Bus General Timing Parameters
Symbol1
Min
Max
Unit
Notes
tLBK
15
—
ns
2
Input setup to local bus clock (LCLKn)
tLBIVKH
7
—
ns
3, 4
Input hold from local bus clock (LCLKn)
tLBIXKH
1.0
—
ns
3, 4
Local bus clock (LCLKn) to output valid
tLBKHOV
—
3
ns
3
Local bus clock (LCLKn) to output high impedance for LAD/LDP
tLBKHOZ
—
4
ns
5
Parameter
Local bus cycle time
Notes:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus
timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case
for clock one(1).
2. All timings are in reference to falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or rising edge of
LCLK0 (for all other inputs).
3. All signals are measured from OVDD/2 of the rising/falling edge of LCLK0 to 0.4  OVDD of the signal in question for 3.3-V
signaling levels.
4. Input timings are measured at the pin.
5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
20
Freescale Semiconductor
Local Bus
Figure 7 provides the AC test load for the local bus.
Z0 = 50 
Output
RL = 50 
OVDD/2
Figure 7. Local Bus AC Test Load
Figure 8 through Figure 10 show the local bus signals. These figures has been given indicate timing
parameters only and do not reflect actual functional operation of interface.
LCLK[n]
tLBIXKH
tLBIVKH
Input Signals:
LAD[0:15]
tLBIXKH
tLBIVKH
Input Signal:
LGTA
tLBIXKH
tLBKHOV
Output Signals:
LBCTL/LBCKE/LOE
tLBKHOV
tLBKHOZ
Output Signals:
LAD[0:15]
tLBOTOT
LALE
Figure 8. Local Bus Signals
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
21
Local Bus
LCLK
T1
T3
tLBKHOV
tLBKHOZ
GPCM Mode Output Signals:
LCS[0:3]/LWE
tLBIVKH
tLBIXKH
UPM Mode Input Signal:
LUPWAIT
tLBIXKH
tLBIVKH
Input Signals:
LAD[0:15]/LDP[0:3]
tLBKHOV
tLBKHOZ
UPM Mode Output Signals:
LCS[0:3]/LBS[0:1]/LGPL[0:5]
Figure 9. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
22
Freescale Semiconductor
Ethernet and MII Management
LCLK
T1
T2
T3
T4
tLBKHOZ
tLBKHOV
GPCM Mode Output Signals:
LCS[0:3]/LWE
tLBIVKH
tLBIXKH
UPM Mode Input Signal:
LUPWAIT
tLBIVKH
tLBIXKH
Input Signals:
LAD[0:15]
tLBKHOV
tLBKHOZ
UPM Mode Output Signals:
LCS[0:3]/LBS[0:1]/LGPL[0:5]
Figure 10. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4
8
Ethernet and MII Management
This section provides the AC and DC electrical characteristics for Ethernet interfaces.
8.1
Ethernet Controller (10/100 Mbps)—MII/RMII Electrical
Characteristics
The electrical characteristics specified here apply to all MII (media independent interface) and RMII
(reduced media independent interface), except MDIO (management data input/output) and MDC
(management data clock). The MII and RMII are defined for 3.3 V. The electrical characteristics for MDIO
and MDC are specified in Section 8.3, “Ethernet Management Interface Electrical Characteristics.”
8.1.1
DC Electrical Characteristics
All MII and RMII drivers and receivers comply with the DC parametric attributes specified in Table 19.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
23
Ethernet and MII Management
Table 19. MII and RMII DC Electrical Characteristics
Parameter
Symbol
Conditions
Min
Max
Unit
Supply voltage 3.3 V
OVDD
—
3
3.6
V
Output high voltage
VOH
IOH = –4.0 mA
OVDD = Min
2.40
OVDD + 0.3
V
Output low voltage
VOL
IOL = 4.0 mA
OVDD = Min
GND
0.50
V
Input high voltage
VIH
—
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
—
–0.3
0.90
V
Input current
IIN
0 V  VIN  OVDD
—
±5
A
8.2
MII and RMII AC Timing Specifications
The AC timing specifications for MII and RMII are presented in this section.
8.2.1
MII AC Timing Specifications
This section describes the MII transmit and receive AC timing specifications.
8.2.1.1
MII Transmit AC Timing Specifications
Table 20 provides the MII transmit AC timing specifications.
Table 20. MII Transmit AC Timing Specifications
At recommended operating conditions with OVDD of 3.3 V ± 300mV.
Symbol1
Min
Typical
Max
Unit
TX_CLK clock period 10 Mbps
tMTX
—
400
—
ns
TX_CLK clock period 100 Mbps
tMTX
—
40
—
ns
tMTXH/tMTX
35
—
65
%
tMTKHDX
1
5
15
ns
TX_CLK data clock rise VIL(min) to VIH(max)
tMTXR
1.0
—
4.0
ns
TX_CLK data clock fall VIH(max) to VIL(min)
tMTXF
1.0
—
4.0
ns
Parameter/Condition
TX_CLK duty cycle
TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay
Note:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit
timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general,
the clock reference symbol representation is based on two to three letters representing the clock of a particular functional.
For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is
used with the appropriate letter: R (rise) or F (fall).
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
24
Freescale Semiconductor
Ethernet and MII Management
Figure 14 provides the AC test load.
Z0 = 50 
Output
RL = 50 
OVDD/2
Figure 11. AC Test Load
Figure 12 shows the MII transmit AC timing diagram.
tMTXR
tMTX
TX_CLK
tMTXH
tMTXF
TXD[3:0]
TX_EN
TX_ER
tMTKHDX
Figure 12. MII Transmit AC Timing Diagram
8.2.1.2
MII Receive AC Timing Specifications
Table 21 provides the MII receive AC timing specifications.
Table 21. MII Receive AC Timing Specifications
At recommended operating conditions with OVDD of 3.3 V ± 300mV.
Symbol1
Min
Typical
Max
Unit
RX_CLK clock period 10 Mbps
tMRX
—
400
—
ns
RX_CLK clock period 100 Mbps
tMRX
—
40
—
ns
tMRXH/tMRX
35
—
65
%
RXD[3:0], RX_DV, RX_ER setup time to RX_CLK
tMRDVKH
10.0
—
—
ns
RXD[3:0], RX_DV, RX_ER hold time to RX_CLK
tMRDXKH
10.0
—
—
ns
RX_CLK clock rise VIL(min) to VIH(max)
tMRXR
1.0
—
4.0
ns
RX_CLK clock fall time VIH(max) to VIL(min)
tMRXF
1.0
—
4.0
ns
Parameter/Condition
RX_CLK duty cycle
Note:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive
timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K)
going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input
signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general,
the clock reference symbol representation is based on three letters representing the clock of a particular functional. For
example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used
with the appropriate letter: R (rise) or F (fall).
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
25
Ethernet and MII Management
Figure 13 shows the MII receive AC timing diagram.
tMRXR
tMRX
RX_CLK
tMRXF
tMRXH
RXD[3:0]
RX_DV
RX_ER
Valid Data
tMRDVKH
tMRDXKH
Figure 13. MII Receive AC Timing Diagram
8.2.2
RMII AC Timing Specifications
This section describes the RMII transmit and receive AC timing specifications.
8.2.2.1
RMII Transmit AC Timing Specifications
Table 20 provides the RMII transmit AC timing specifications.
Table 22. RMII Transmit AC Timing Specifications
At recommended operating conditions with OVDD of 3.3 V ± 300mV.
Symbol1
Min
Typical
Max
Unit
tRMX
—
20
—
ns
tRMXH/tRMX
35
—
65
%
REF_CLK to RMII data TXD[1:0], TX_EN delay
tRMTKHDX
2
—
13
ns
REF_CLK data clock rise VIL(min) to VIH(max)
tRMXR
1.0
—
4.0
ns
REF_CLK data clock fall VIH(max) to VIL(min)
tRMXF
1.0
—
4.0
ns
Parameter/Condition
REF_CLK clock
REF_CLK duty cycle
Note:
1. The symbols used for timing specifications follow the pattern of t(first three letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMTKHDX symbolizes RMII
transmit timing (RMT) for the time tRMX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in
general, the clock reference symbol representation is based on two to three letters representing the clock of a particular
functional. For example, the subscript of tRMX represents the RMII(RM) reference (X) clock. For rise and fall times, the latter
convention is used with the appropriate letter: R (rise) or F (fall).
Figure 14 provides the AC test load.
Output
Z0 = 50 
RL = 50 
OVDD/2
Figure 14. AC Test Load
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
26
Freescale Semiconductor
Ethernet and MII Management
Figure 15 shows the RMII transmit AC timing diagram.
tRMXR
tRMX
REF_CLK
tRMXH
tRMXF
TXD[1:0]
TX_EN
tRMTKHDX
Figure 15. RMII Transmit AC Timing Diagram
8.2.2.2
RMII Receive AC Timing Specifications
Table 21 provides the RMII receive AC timing specifications.
Table 23. RMII Receive AC Timing Specifications
At recommended operating conditions with OVDD of 3.3 V ± 300mV.
Symbol1
Min
Typical
Max
Unit
tRMX
—
20
—
ns
tRMXH/tRMX
35
—
65
%
RXD[1:0], CRS_DV, RX_ER setup time to REF_CLK
tRMRDVKH
4.0
—
—
ns
RXD[1:0], CRS_DV, RX_ER hold time to REF_CLK
tRMRDXKH
2.0
—
—
ns
REF_CLK clock rise VIL(min) to VIH(max)
tRMXR
1.0
—
4.0
ns
REF_CLK clock fall time VIH(max) to VIL(min)
tRMXF
1.0
—
4.0
ns
Parameter/Condition
REF_CLK clock period
REF_CLK duty cycle
Note:
1. The symbols used for timing specifications follow the pattern of t(first three letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMRDVKH symbolizes RMII
receive timing (RMR) with respect to the time data input signals (D) reach the valid state (V) relative to the tRMX clock
reference (K) going to the high (H) state or setup time. Also, tRMRDXKL symbolizes RMII receive timing (RMR) with respect
to the time data input signals (D) went invalid (X) relative to the tRMX clock reference (K) going to the low (L) state or hold
time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a
particular functional. For example, the subscript of tRMX represents the RMII (RM) reference (X) clock. For rise and fall times,
the latter convention is used with the appropriate letter: R (rise) or F (fall).
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
27
Ethernet and MII Management
Figure 16 shows the RMII receive AC timing diagram.
tRMXR
tRMX
REF_CLK
tRMXF
tRMXH
RXD[1:0]
CRS_DV
RX_ER
Valid Data
tRMRDVKH
tRMRDXKH
Figure 16. RMII Receive AC Timing Diagram
8.3
Ethernet Management Interface Electrical Characteristics
The electrical characteristics specified here apply to MII management interface signals MDIO
(management data input/output) and MDC (management data clock). The electrical characteristics for
MII, and RMII are specified in Section 8.1, “Ethernet Controller (10/100 Mbps)—MII/RMII Electrical
Characteristics.”
8.3.1
MII Management DC Electrical Characteristics
MDC and MDIO are defined to operate at a supply voltage of 3.3 V. The DC electrical characteristics for
MDIO and MDC are provided in Table 24.
Table 24. MII Management DC Electrical Characteristics When Powered at 3.3 V
Parameter
Supply voltage (3.3 V)
Symbol
Conditions
Min
Max
Unit
OVDD
—
3
3.6
V
Output high voltage
VOH
IOH = –1.0 mA
OVDD = Min
2.40
OVDD + 0.3
V
Output low voltage
VOL
IOL = 1.0 mA
OVDD = Min
GND
0.50
V
Input high voltage
VIH
—
2.00
—
V
Input low voltage
VIL
—
—
0.80
V
Input current
IIN
0 V  VIN  OVDD
—
±5
A
8.3.2
MII Management AC Electrical Specifications
Table 25 provides the MII management AC timing specifications.
Table 25. MII Management AC Timing Specifications
At recommended operating conditions with OVDD is 3.3 V ± 300mV.
Symbol1
Min
Typical
Max
Unit
Notes
MDC frequency
fMDC
—
2.5
—
MHz
—
MDC period
tMDC
—
400
—
ns
—
MDC clock pulse width high
tMDCH
32
—
—
ns
—
Parameter/Condition
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
28
Freescale Semiconductor
Ethernet and MII Management
Table 25. MII Management AC Timing Specifications (continued)
At recommended operating conditions with OVDD is 3.3 V ± 300mV.
Symbol1
Min
Typical
Max
Unit
Notes
MDC to MDIO delay
tMDKHDX
10
—
70
ns
—
MDIO to MDC setup time
tMDDVKH
8.5
—
—
ns
—
MDIO to MDC hold time
tMDDXKH
0
—
—
ns
—
MDC rise time
tMDCR
—
—
10
ns
—
MDC fall time
tMDHF
—
—
10
ns
—
Parameter/Condition
Note:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes
management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data
hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the
valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the
latter convention is used with the appropriate letter: R (rise) or F (fall).
Figure 17 shows the MII management AC timing diagram.
tMDC
tMDCR
MDC
tMDCH
tMDCF
MDIO
(Input)
tMDDVKH
tMDDXKH
MDIO
(Output)
tMDKHDX
Figure 17. MII Management Interface Timing Diagram
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
29
Ethernet and MII Management
IEEE 1588 DC Specifications
8.3.3
The IEEE 1588 DC timing specifications are given in Table 27.
Table 26. IEEE 1588 DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
unit
Output high voltage
VOH
IOH = -8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
IOL = 3.2mA
—
0.4
V
Output low voltage
VOL
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
- 0.3
0.8
V
Input current
IIN
0V ≤ VIN ≤ OVDD
—
±5
μA
8.3.4
IEEE 1588 AC Specifications
The IEEE 1588 AC timing specifications are given in Table 27.
Table 27. IEEE 1588 AC Timing Specifications
At recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter/Condition
Symbol
Min
Typ
Max
Unit
Notes
QE_1588_CLK clock period
tT1588CLK
2.5
—
TRX_CLK  9
ns
1, 3
tT1588CLKH/tT1588CLK
40
50
60
%
—
QE_1588_CLK peak-to-peak jitter
tT1588CLKINJ
—
—
250
ps
—
Rise time QE_1588_CLK
(20%–80%)
tT1588CLKINR
1.0
—
2.0
ns
—
Fall time QE_1588_CLK
(80%–20%)
tT1588CLKINF
1.0
—
2.0
ns
—
QE_1588_CLK_OUT clock period
tT1588CLKOUT
2  tT1588CLK
—
—
ns
—
QE_1588_CLK_OUT duty cycle
tT1588CLKOTH
/tT1588CLKOUT
30
50
70
%
—
tT1588OV
0.5
—
3.0
ns
—
tT1588TRIGH
2  tT1588CLK_MAX
—
—
ns
2
QE_1588_CLK duty cycle
QE_1588_PULSE_OUT
QE_1588_TRIG_IN pulse width
Notes:
1.TRX_CLK is the max clock period of QUICC engine receiving clock selected by TMR_CTRL[CKSEL]. See the MPC
PowerQUICC II Pro Integrated Processor Family Reference Manual, for a description of TMR_CTRL registers.
2. It need to be at least two times of clock period of clock selected by TMR_CTRL[CKSEL]. See the MPC PowerQUICC II Pro
Integrated Processor Family Reference Manual, for a description of TMR_CTRL registers.
3. The maximum value of tT1588CLK is not only defined by the value of TRX_CLK, but also defined by the recovered clock. For
example, for 10/100 Mbps modes, the maximum value of tT1588CLK is 3600 and 280ns, respectively.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
30
Freescale Semiconductor
TDM/SI
Figure 18 provides the data and command output timing diagram.
tT1588CLKOUT
tT1588CLKOUTH
TSEC_1588_CLK_OUT
tT1588OV
TSEC_1588_PULSE_OUT
TSEC_1588_TRIG_OUT
Note: The output delay is count starting rising edge if tT1588CLKOUT is non-inverting. Otherwise, it is
count starting falling edge.
Figure 18. IEEE 1588 Output AC Timing
Figure 19 provides the data and command input timing diagram.
tT1588CLK
tT1588CLKH
TSEC_1588_CLK
TSEC_1588_TRIG_IN
tT1588TRIGH
Figure 19. IEEE 1588 Input AC Timing
9
TDM/SI
This section describes the DC and AC electrical specifications for the time-division-multiplexed and serial
interface of the MPC8309.
9.1
TDM/SI DC Electrical Characteristics
Table 28 provides the DC electrical characteristics for the MPC8309 TDM/SI.
Table 28. TDM/SI DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –2.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.5
V
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V  VIN  OVDD
—
±5
A
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
31
TDM/SI
9.2
TDM/SI AC Timing Specifications
Table 29 provides the TDM/SI input and output AC timing specifications.
Table 29. TDM/SI AC Timing Specifications1
Symbol2
Min
Max
Unit
TDM/SI outputs—External clock delay
tSEKHOV
2
14
ns
TDM/SI outputs—External clock High Impedance
tSEKHOX
2
10
ns
TDM/SI inputs—External clock input setup time
tSEIVKH
5
—
ns
TDM/SI inputs—External clock input hold time
tSEIXKH
2
—
ns
Characteristic
Notes:
1. Output specifications are measured from the 50% level of the rising edge of QE_CLK_IN to the 50% level of the signal.
Timings are measured at the pin.
2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tSEKHOX symbolizes the TDM/SI
outputs external timing (SE) for the time tTDM/SI memory clock reference (K) goes from the high state (H) until outputs (O)
are invalid (X).
Figure 20 provides the AC test load for the TDM/SI.
Output
Z0 = 50 
RL = 50 
OVDD/2
Figure 20. TDM/SI AC Test Load
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
32
Freescale Semiconductor
HDLC
Figure 21 represents the AC timing from Table 29. Note that although the specifications generally
reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the
active edge.
TDM/SICLK (Input)
tSEIXKH
tSEIVKH
Input Signals:
TDM/SI
(See Note)
tSEKHOV
Output Signals:
TDM/SI
(See Note)
tSEKHOX
Note: The clock edge is selectable on TDM/SI.
Figure 21. TDM/SI AC Timing (External Clock) Diagram
10 HDLC
This section describes the DC and AC electrical specifications for the high level data link control (HDLC),
of the MPC8309.
10.1
HDLC DC Electrical Characteristics
Table 30 provides the DC electrical characteristics for the MPC8309 HDLC protocol.
Table 30. HDLC DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –2.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.5
V
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V  VIN OVDD
—
±5
A
10.2
HDLC AC Timing Specifications
Table 31 provides the input and output AC timing specifications for HDLC protocol.
Table 31. HDLC AC Timing Specifications1
Symbol2
Min
Max
Unit
Outputs—Internal clock delay
tHIKHOV
0
9
ns
Outputs—External clock delay
tHEKHOV
1
12
ns
Outputs—Internal clock high impedance
tHIKHOX
0
5.5
ns
Characteristic
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
33
HDLC
Table 31. HDLC AC Timing Specifications1 (continued)
Symbol2
Min
Max
Unit
tHEKHOX
1
8
ns
Inputs—Internal clock input setup time
tHIIVKH
9
—
ns
Inputs—External clock input setup time
tHEIVKH
4
—
ns
Inputs—Internal clock input hold time
tHIIXKH
0
—
ns
Inputs—External clock input hold time
tHEIXKH
1
—
ns
Characteristic
Outputs—External clock high impedance
Notes:
1. Output specifications are measured from the 50% level of the rising edge of QE_CLK_IN to the 50% level of the signal.
Timings are measured at the pin.
2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tHIKHOX symbolizes the outputs
internal timing (HI) for the time tserial memory clock reference (K) goes from the high state (H) until outputs (O) are invalid (X).
Figure 22 provides the AC test load.
Output
Z0 = 50 
RL = 50 
OVDD/2
Figure 22. AC Test Load
Figure 23 and Figure 24 represent the AC timing from Table 31. Note that although the specifications
generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge
is the active edge.
Figure 23 shows the timing with external clock.
Serial CLK (Input)
tHEIVKH
tHEIXKH
Input Signals:
(See Note)
tHEKHOV
Output Signals:
(See Note)
tHEKHOX
Note: The clock edge is selectable.
Figure 23. AC Timing (External Clock) Diagram
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
34
Freescale Semiconductor
PCI
Figure 24 shows the timing with internal clock.
Serial CLK (Output)
tHIIXKH
tHIIVKH
Input Signals:
(See Note)
tHIKHOV
Output Signals:
(See Note)
tHIKHOX
Note: The clock edge is selectable.
Figure 24. AC Timing (Internal Clock) Diagram
11 PCI
This section describes the DC and AC electrical specifications for the PCI bus of the MPC8309.
11.1
PCI DC Electrical Characteristics
Table 32 provides the DC electrical characteristics for the PCI interface of the MPC8309.
Table 32. PCI DC Electrical Characteristics1,2
Parameter
Symbol
Test Condition
Min
Max
Unit
High-level input voltage
VIH
VOUT VOH (min) or
2
OVDD + 0.3
V
Low-level input voltage
VIL
VOUT  VOL (max)
–0.3
0.8
V
High-level output voltage
VOH
OVDD = min,
IOH = –100 A
OVDD – 0.2
—
V
Low-level output voltage
VOL
OVDD = min,
IOL = 100 A
—
0.2
V
IIN
0 V VIN OVDD
—
±5
A
Input current
Notes:
1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2.
2. Ranges listed do not meet the full range of the DC specifications of the PCI 2.3 Local Bus Specifications.
11.2
PCI AC Electrical Specifications
This section describes the general AC timing parameters of the PCI bus of the MPC8309. Note that the
PCI_CLK or PCI_SYNC_IN signal is used as the PCI input clock depending on whether the MPC8309 is
configured as a host or agent device. Table 33 shows the PCI AC timing specifications at 66 MHz.
.
Table 34 shows the PCI AC timing specifications at 33 MHz.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
35
PCI
Table 33. PCI AC Timing Specifications at 66 MHz
Symbol1
Min
Max
Unit
Notes
Clock to output valid
tPCKHOV
—
6.0
ns
2
Output hold from clock
tPCKHOX
1
—
ns
2
Clock to output high impedence
tPCKHOZ
—
14
ns
2, 3
Input setup to clock
tPCIVKH
3.0
—
ns
2, 4
Input hold from clock
tPCIXKH
0
—
ns
2, 4
Parameter
Notes:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing
(PC) with respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN clock, tSYS, reference
(K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset
(R) went high (H) relative to the frame signal (F) going to the valid (V) state.
2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications.
3. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
4. Input timings are measured at the pin.
Table 34. PCI AC Timing Specifications at 33 MHz
Symbol1
Min
Max
Unit
Notes
Clock to output valid
tPCKHOV
—
11
ns
2
Output hold from clock
tPCKHOX
2
—
ns
2
Clock to output high impedence
tPCKHOZ
—
14
ns
2, 3
Input setup to clock
tPCIVKH
3.0
—
ns
2, 4
Input hold from clock
tPCIXKH
0
—
ns
2, 4
Parameter
Notes:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing
(PC) with respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN clock, tSYS, reference
(K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset
(R) went high (H) relative to the frame signal (F) going to the valid (V) state.
2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications.
3. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
4. Input timings are measured at the pin.
Figure 25 provides the AC test load for PCI.
Output
Z0 = 50 
RL = 50 
OVDD/2
Figure 25. PCI AC Test Load
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
36
Freescale Semiconductor
USB
Figure 26 shows the PCI input AC timing conditions.
CLK
tPCIVKH
tPCIXKH
Input
Figure 26. PCI Input AC Timing Measurement Conditions
Figure 27 shows the PCI output AC timing conditions.
CLK
tPCKHOV
tPCKHOX
Output Delay
tPCKHOZ
High-Impedance
Output
Figure 27. PCI Output AC Timing Measurement Condition
12 USB
12.1
USB Controller
This section provides the AC and DC electrical specifications for the USB (ULPI) interface.
12.1.1
USB DC Electrical Characteristics
Table 35 provides the DC electrical characteristics for the USB interface.
Table 35. USB DC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
High-level input voltage
VIH
2.0
OVDD + 0.3
V
Low-level input voltage
VIL
–0.3
0.8
V
Input current
IIN
—
±5
A
High-level output voltage, IOH = –100 A
VOH
OVDD – 0.2
—
V
Low-level output voltage, IOL = 100 A
VOL
—
0.2
V
12.1.2
USB AC Electrical Specifications
Table 36 describes the general timing parameters of the USB interface.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
37
USB
Table 36. USB General Timing Parameters
Symbol1
Min
Max
Unit
tUSCK
15
—
ns
Input setup to USB clock—all inputs
tUSIVKH
4
—
ns
input hold to USB clock—all inputs
tUSIXKH
1
—
ns
USB clock to output valid—all outputs (except
USBDR_STP_USBDR_STP)
tUSKHOV
—
7
ns
USB clock to output valid—USBDR_STP
tUSKHOV
—
7.5
ns
Output hold from USB clock—all outputs
tUSKHOX
2
—
ns
Parameter
USB clock cycle time
Notes
Note:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes USB timing
(USB) for the input (I) to go invalid (X) with respect to the time the USB clock reference (K) goes high (H). Also, tUSKHOX
symbolizes us timing (USB) for the USB clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or
output hold time.
Figure 28 and Figure 29 provide the AC test load and signals for the USB, respectively.
Z0 = 50 
Output
RL = 50 
OVDD/2
Figure 28. USB AC Test Load
USBDR_CLK
tUSIVKH
tUSIXKH
Input Signals
tUSKHOV
tUSKHOX
Output Signals
Figure 29. USB Signals
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
38
Freescale Semiconductor
DUART
13 DUART
This section describes the DC and AC electrical specifications for the DUART interface of the MPC8309.
13.1
DUART DC Electrical Characteristics
Table 37 provides the DC electrical characteristics for the DUART interface of the MPC8309.
Table 37. DUART DC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
OVDD + 0.3
V
Low-level input voltage OVDD
VIL
–0.3
0.8
V
High-level output voltage, IOH = –100 A
VOH
OVDD – 0.2
—
V
Low-level output voltage, IOL = 100 A
VOL
—
0.2
V
IIN
—
±5
A
Input current (0 V VIN OVDD
)1
Note:
1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2.
13.2
DUART AC Electrical Specifications
Table 38 provides the AC timing parameters for the DUART interface of the MPC8309.
Table 38. DUART AC Timing Specifications
Parameter
Value
Unit
Minimum baud rate
256
baud
Maximum baud rate
>1,000,000
baud
1
16
—
2
Oversample rate
Notes
Notes:
1. Actual attainable baud rate is limited by the latency of interrupt processing.
2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are
sampled each 16th sample.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
39
eSDHC
14 eSDHC
This section describes the DC and AC electrical specifications for the eSDHC interface of the device.
14.1
eSDHC DC Electrical Characteristics
Table 39 provides the DC electrical characteristics for the eSDHC interface.
Table 39. eSDHC Interface DC Electrical Characteristics
At recommended operating conditions with OVDD = 3.3 V
Characteristic
Symbol
Condition
Min
Max
Unit
Notes
Input high voltage
VIH
—
0.625  OVDD
—
V
1
Input low voltage
VIL
—
—
0.25  OVDD
V
1
Output high voltage
VOH
IOH = –100 A at
OVDD min
0.75  OVDD
—
V
—
Output low voltage
VOL
IOL = 100 A at
OVDD min
—
0.125  OVDD
V
—
Output high voltage
VOH
IOH = –100 mA
OVDD – 0.2
—
V
2
Output low voltage
VOL
IOL = 2 mA
—
0.3
V
2
IIN/IOZ
—
–10
10
A
—
Input/output leakage current
Note:
1. Note that the min VILand max VIH values are based on the respective min and max OVIN values found in Table 2..
2. Open drain mode for MMC cards only.
14.2
eSDHC AC Timing Specifications
Table 40 provides the eSDHC AC timing specifications as defined in Figure 30 and Figure 31.
Table 40. eSDHC AC Timing Specifications
At recommended operating conditions with OVDD = 3.3 V
Symbol1
Min
Max
Unit
Notes
SD_CLK clock frequency:
SD/SDIO Full-speed/High-speed mode
MMC Full-speed/High-speed mode
fSHSCK
0
25/33.25
20/52
MHz
2, 4
SD_CLK clock low time—Full-speed/High-speed mode
tSHSCKL
10/7
—
ns
4
SD_CLK clock high time—Full-speed/High-speed mode
tSHSCKH
10/7
—
ns
4
SD_CLK clock rise and fall times
tSHSCKR/
tSHSCKF
—
3
ns
4
Input setup times: SD_CMD, SD_DATx, SD_CD to
SD_CLK
tSHSIVKH
5
—
ns
4
Parameter
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
40
Freescale Semiconductor
eSDHC
Table 40. eSDHC AC Timing Specifications (continued)
At recommended operating conditions with OVDD = 3.3 V
Symbol1
Min
Max
Unit
Notes
Input hold times: SD_CMD, SD_DATx, SD_CD to
SD_CLK
tSHSIXKH
2.5
—
ns
3, 4
Output delay time: SD_CLK to SD_CMD, SD_DATx valid
tSHSKHOV
–3
3
ns
4
Parameter
Notes:
1. The symbols used for timing specifications herein follow the pattern of t(first three letters of functional block)(signal)(state)
(reference)(state) for inputs and t(first three letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tFHSKHOV
symbolizes eSDHC high-speed mode device timing (SHS) clock reference (K) going to the high (H) state, with respect to the
output (O) reaching the invalid state (X) or output hold time. Note that in general, the clock reference symbol is based on five
letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the
appropriate letter: R (rise) or F (fall).
2. In full-speed mode, the clock freqency value can be 0–25 MHz for an SD/SDIO card and 0–20 MHz for an MMC card. In
high-speed mode, the clock freqency value can be 0–33.25 MHz for an SD/SDIO card and 0–52 MHz for an MMC card.
3. To satisfy hold timing, the delay difference between clock input and cmd/data input must not exceed 2 ns.
4. CCARD  10 pF, (1 card), and CL = CBUS + CHOST + CCARD 40 pF
Figure 30 provides the eSDHC clock input timing diagram.
eSDHC
External Clock
operational mode
VM
VM
VM
tSHSCKL
tSHSCKH
tSHSCK
VM = Midpoint Voltage (OVDD/2)
tSHSCKR
tSHSCKF
Figure 30. eSDHC Clock Input Timing Diagram
Figure 31 provides the data and command input/output timing diagram.
SD_CK
External Clock
VM
VM
tSHSIVKH
VM
VM
tSHSIXKH
SD_DAT/CMD
Inputs
SD_DAT/CMD
Outputs
tSHSKHOV
VM = Midpoint Voltage (OVDD/2)
Figure 31. eSDHC Data and Command Input/Output Timing Diagram Referenced to Clock
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
41
FlexCAN
15 FlexCAN
This section describes the DC and AC electrical specifications for the FlexCAN interface.
15.1
FlexCAN DC Electrical Characteristics
Table 41 provides the DC electrical characteristics for the FlexCAN interface.
Table 41. FlexCAN DC Electrical Characteristics (3.3V)
For recommended operating conditions, see Table 2
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±5
A
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. Min VILand max VIH values are based on the respective min and max OVIN values found in Table 2.
2. OVIN represents the input voltage of the supply. It is referenced in Table 2.
15.2
FlexCAN AC Timing Specifications
Table 42 provides the AC timing specifications for the FlexCAN interface.
Table 42. FlexCAN AC Timing Specifications
For recommended operating conditions, see Table 2
Parameter
Baud rate
Min
Max
Unit
Notes
10
1000
Kbps
—
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
42
Freescale Semiconductor
I2 C
16 I2C
This section describes the DC and AC electrical characteristics for the I2C interface of the MPC8309.
16.1
I2C DC Electrical Characteristics
Table 43 provides the DC electrical characteristics for the I2C interface of the MPC8309.
Table 43. I2C DC Electrical Characteristics
At recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage level
VIH
0.7  OVDD
OVDD + 0.3
V
—
Input low voltage level
VIL
–0.3
0.3  OVDD
V
—
Low level output voltage
VOL
0
0.4
V
1
Output fall time from VIH(min) to VIL(max) with a bus
capacitance from 10 to 400 pF
tI2KLKV
20 + 0.1  CB
250
ns
2
Pulse width of spikes which must be suppressed by the
input filter
tI2KHKL
0
50
ns
3
Capacitance for each I/O pin
CI
—
10
pF
—
Input current (0 V VIN OVDD)
IIN
—
±5
A
4
Notes:
1. Output voltage (open drain or open collector) condition = 3 mA sink current.
2. CB = capacitance of one bus line in pF.
3. Refer to the MPC8309 PowerQUICC II Pro Integrated Communications Processor Reference Manual for information on
the digital filter used.
4. I/O pins obstructs the SDA and SCL lines if OVDD is switched off.
16.2
I2C AC Electrical Specifications
Table 44 provides the AC timing parameters for the I2C interface of the MPC8309.
Table 44. I2C AC Electrical Specifications
All values refer to VIH (min) and VIL (max) levels (see Table 43).
Symbol1
Min
Max
Unit
SCL clock frequency
fI2C
0
400
kHz
Low period of the SCL clock
tI2CL
1.3
—
s
High period of the SCL clock
tI2CH
0.6
—
s
Setup time for a repeated START condition
tI2SVKH
0.6
—
s
Hold time (repeated) START condition (after this period, the first clock
pulse is generated)
tI2SXKL
0.6
—
s
Data setup time
tI2DVKH
100
—
ns
300
0.93
s
300
ns
Parameter
Data hold time:
I2C
bus devices
Rise time of both SDA and SCL signals
tI2DXKL
tI2CR
20 + 0.1
CB4
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
43
I2 C
Table 44. I2C AC Electrical Specifications (continued)
All values refer to VIH (min) and VIL (max) levels (see Table 43).
Symbol1
Min
Max
Unit
tI2CF
20 + 0.1 CB4
300
ns
Setup time for STOP condition
tI2PVKH
0.6
—
s
Bus free time between a STOP and START condition
tI2KHDX
1.3
—
s
Noise margin at the LOW level for each connected device (including
hysteresis)
VNL
0.1  OVDD
—
V
Noise margin at the HIGH level for each connected device (including
hysteresis)
VNH
0.2  OVDD
—
V
Parameter
Fall time of both SDA and SCL signals
Notes:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2)
with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high
(H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition
(S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C
timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock
reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate
letter: R (rise) or F (fall).
2. MPC8309 provides a hold time of at least 300 ns for the SDA signal (referred to the VIH(min) of the SCL signal) to bridge
the undefined region of the falling edge of SCL.
3. The maximum tI2DVKL has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal.
4. CB = capacitance of one bus line in pF.
Figure 32 provides the AC test load for the I2C.
Z0 = 50 
Output
RL = 50 
OVDD/2
Figure 32. I2C AC Test Load
Figure 33 shows the AC timing diagram for the I2C bus.
SDA
tI2CF
tI2DVKH
tI2CL
tI2KHKL
tI2SXKL
tI2CF
tI2CR
SCL
tI2SXKL
S
tI2CH
tI2DXKL
tI2SVKH
Sr
tI2PVKH
P
S
2
Figure 33. I C Bus AC Timing Diagram
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
44
Freescale Semiconductor
Timers
17 Timers
This section describes the DC and AC electrical specifications for the timers of the MPC8309.
17.1
Timer DC Electrical Characteristics
Table 45 provides the DC electrical characteristics for the MPC8309 timer pins, including TIN, TOUT,
TGATE, and RTC_PIT_CLK.
Table 45. Timer DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –6.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 6.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V  VIN  OVDD
—
±5
A
17.2
Timer AC Timing Specifications
Table 46 provides the timer input and output AC timing specifications.
Table 46. Timer Input AC Timing Specifications1
Characteristic
Timers inputs—minimum pulse width
Symbol2
Min
Unit
tTIWID
20
ns
Notes:
1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.
2. Timer inputs and outputs are asynchronous to any visible clock. Timer outputs should be synchronized before use by any
external synchronous logic. Timer inputs are required to be valid for at least tTIWID ns to ensure proper operation.
Figure 34 provides the AC test load for the timers.
Output
Z0 = 50 
RL = 50 
OVDD/2
Figure 34. Timers AC Test Load
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
45
GPIO
18 GPIO
This section describes the DC and AC electrical specifications for the GPIO of the MPC8309.
18.1
GPIO DC Electrical Characteristics
Table 11 provides the DC electrical characteristics for the MPC8309 GPIO.
Table 47. GPIO DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Notes
Output high voltage
VOH
IOH = –6.0 mA
2.4
—
V
1
Output low voltage
VOL
IOL = 6.0 mA
—
0.5
V
1
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
1
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
1
Input low voltage
VIL
—
–0.3
0.8
V
—
Input current
IIN
0 V VIN OVDD
—
±5
A
—
Note:
1. This specification applies when operating from 3.3-V supply.
18.2
GPIO AC Timing Specifications
Table 48 provides the GPIO input and output AC timing specifications.
Table 48. GPIO Input AC Timing Specifications1
Characteristic
GPIO inputs—minimum pulse width
Symbol2
Min
Unit
tPIWID
20
ns
Notes:
1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.
2. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs should be synchronized before use by any
external synchronous logic. GPIO inputs are required to be valid for at least tPIWID ns to ensure proper operation.
Figure 35 provides the AC test load for the GPIO.
Output
Z0 = 50 
RL = 50 
OVDD/2
Figure 35. GPIO AC Test Load
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
46
Freescale Semiconductor
IPIC
19 IPIC
This section describes the DC and AC electrical specifications for the external interrupt pins of the
MPC8309.
19.1
IPIC DC Electrical Characteristics
Table 49 provides the DC electrical characteristics for the external interrupt pins of the MPC8309.
Table 49. IPIC DC Electrical Characteristics1,2
Characteristic
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
—
—
±5
A
Output High Voltage
VOH
IOL = -8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 6.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Notes:
1. This table applies for pins IRQ, MCP_OUT, and QE ports Interrupts.
2. MCP_OUT is open drain pins, thus VOH is not relevant for those pins.
19.2
IPIC AC Timing Specifications
Table 50 provides the IPIC input and output AC timing specifications.
Table 50. IPIC Input AC Timing Specifications1
Characteristic
IPIC inputs—minimum pulse width
Symbol2
Min
Unit
tPIWID
20
ns
Notes:
1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.
2. IPIC inputs and outputs are asynchronous to any visible clock. IPIC outputs should be synchronized before use by any
external synchronous logic. IPIC inputs are required to be valid for at least tPIWID ns to ensure proper operation when working
in edge triggered mode.
20 SPI
This section describes the DC and AC electrical specifications for the SPI of the MPC8309.
20.1
SPI DC Electrical Characteristics
Table 51 provides the DC electrical characteristics for the MPC8309 SPI.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
47
SPI
Table 51. SPI DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –6.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 6.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V  VIN  OVDD
—
±5
A
20.2
SPI AC Timing Specifications
Table 52 and provide the SPI input and output AC timing specifications.
Table 52. SPI AC Timing Specifications1
Symbol2
Min
Max
Unit
SPI outputs—Master mode (internal clock) delay
tNIKHOV
0.5
6
ns
SPI outputs—Slave mode (external clock) delay
tNEKHOV
2
8
ns
SPI inputs—Master mode (internal clock) input setup time
tNIIVKH
6
—
ns
SPI inputs—Master mode (internal clock) input hold time
tNIIXKH
0
—
ns
SPI inputs—Slave mode (external clock) input setup time
tNEIVKH
4
—
ns
SPI inputs—Slave mode (external clock) input hold time
tNEIXKH
2
—
ns
Characteristic
Notes:
1. Output specifications are measured from the 50% level of the rising edge of SPICLK to the 50% level of the signal. Timings
are measured at the pin.
2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOV symbolizes the NMSI
outputs internal timing (NI) for the time tSPI memory clock reference (K) goes from the high state (H) until outputs (O) are
valid (V).
3. All units of output delay must be enabled for 8309_output_port spimosi_lpgl0(SPI Master Mode)
4. delay units must not be enabled for Slave Mode.
Figure 36 provides the AC test load for the SPI.
Output
Z0 = 50 
RL = 50 
OVDD/2
Figure 36. SPI AC Test Load
Figure 37 and Figure 38 represent the AC timing from Table 52. Note that although the specifications
generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge
is the active edge.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
48
Freescale Semiconductor
JTAG
Figure 37 shows the SPI timing in slave mode (external clock).
SPICLK (Input)
tNEIXKH
tNEIVKH
Input Signals:
SPIMOSI
(See Note)
tNEKHOV
Output Signals:
SPIMISO
(See Note)
Note: The clock edge is selectable on SPI.
Figure 37. SPI AC Timing in Slave Mode (External Clock) Diagram
Figure 38 shows the SPI timing in master mode (internal clock).
SPICLK (Output)
tNIIXKH
tNIIVKH
Input Signals:
SPIMISO
(See Note)
tNIKHOV
Output Signals:
SPIMOSI
(See Note)
Note: The clock edge is selectable on SPI.
Figure 38. SPI AC Timing in Master Mode (Internal Clock) Diagram
21 JTAG
This section describes the DC and AC electrical specifications for the IEEE Std. 1149.1™ (JTAG)
interface of the MPC8309.
21.1
JTAG DC Electrical Characteristics
Table 53 provides the DC electrical characteristics for the IEEE Std. 1149.1 (JTAG) interface of the
MPC8309.
Table 53. JTAG Interface DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –6.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 6.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
49
JTAG
Table 53. JTAG Interface DC Electrical Characteristics (continued)
Characteristic
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V  VIN  OVDD
—
±5
A
21.2
JTAG AC Electrical Characteristics
This section describes the AC electrical specifications for the IEEE Std. 1149.1 (JTAG) interface of the
MPC8309. Table 54 provides the JTAG AC timing specifications as defined in Figure 40 through
Figure 43.
Table 54. JTAG AC Timing Specifications (Independent of SYS_CLK_IN)1
At recommended operating conditions (see Table 2).
Symbol2
Min
Max
Unit
Notes
JTAG external clock frequency of operation
fJTG
0
33.3
MHz
—
JTAG external clock cycle time
t JTG
30
—
ns
—
tJTKHKL
11
—
ns
—
tJTGR, tJTGF
0
2
ns
—
tTRST
25
—
ns
3
Boundary-scan data
TMS, TDI
tJTDVKH
tJTIVKH
4
4
—
—
Boundary-scan data
TMS, TDI
tJTDXKH
tJTIXKH
10
10
—
—
Boundary-scan data
TDO
tJTKLDV
tJTKLOV
2
2
15
15
Parameter
JTAG external clock pulse width measured at 1.4 V
JTAG external clock rise and fall times
TRST assert time
Input setup times:
ns
Input hold times:
4
ns
Valid times:
4
ns
5
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
50
Freescale Semiconductor
JTAG
Table 54. JTAG AC Timing Specifications (Independent of SYS_CLK_IN)1 (continued)
At recommended operating conditions (see Table 2).
Symbol2
Min
Max
Boundary-scan data
TDO
tJTKLDX
tJTKLOX
2
2
—
—
JTAG external clock to output high impedance:
Boundary-scan data
TDO
tJTKLDZ
tJTKLOZ
2
2
19
9
Parameter
Unit
Notes
ns
Output hold times:
5
ns
5, 6
6
Notes:
1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question.
The output timings are measured at the pins. All output timings assume a purely resistive 50-load (see Figure 39).
Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device
timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K)
going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals
(D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference
symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the
latter convention is used with the appropriate letter: R (rise) or F (fall).
3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.
4. Non-JTAG signal input timing with respect to tTCLK.
5. Non-JTAG signal output timing with respect to tTCLK.
6. Guaranteed by design and characterization.
Figure 39 provides the AC test load for TDO and the boundary-scan outputs of the MPC8309.
Z0 = 50 
Output
RL = 50 
OVDD/2
Figure 39. AC Test Load for the JTAG Interface
Figure 40 provides the JTAG clock input timing diagram.
JTAG
External Clock
VM
VM
VM
tJTGR
tJTKHKL
tJTGF
tJTG
VM = Midpoint Voltage (OVDD/2)
Figure 40. JTAG Clock Input Timing Diagram
Figure 41 provides the TRST timing diagram.
TRST
VM
VM
tTRST
VM = Midpoint Voltage (OVDD/2)
Figure 41. TRST Timing Diagram
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
51
JTAG
Figure 42 provides the boundary-scan timing diagram.
JTAG
External Clock
VM
VM
tJTDVKH
tJTDXKH
Input
Data Valid
Boundary
Data Inputs
tJTKLDV
tJTKLDX
Boundary
Data Outputs
Output Data Valid
tJTKLDZ
Boundary
Data Outputs
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
Figure 42. Boundary-Scan Timing Diagram
Figure 43 provides the test access port timing diagram.
JTAG
External Clock
VM
VM
tJTIVKH
tJTIXKH
Input
Data Valid
TDI, TMS
tJTKLOV
tJTKLOX
TDO
Output Data Valid
tJTKLOZ
TDO
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
Figure 43. Test Access Port Timing Diagram
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
52
Freescale Semiconductor
Package and Pin Listings
22 Package and Pin Listings
This section details package parameters, pin assignments, and dimensions. The MPC8309 is available in
a thermally enhanced MAPBGA (mold array process-ball grid array); see Section 22.1, “Package
Parameters for the MPC8309,” and Section 22.2, “Mechanical Dimensions of the MPC8309 MAPBGA,”
for information on the MAPBGA.
22.1
Package Parameters for the MPC8309
The package parameters are as provided in the following list.
Package outline
19 mm 19 mm
Package Type
MAPBGA
Interconnects
489
Pitch
0.80 mm
Module height (typical)
1.48 mm; Min = 1.31mm and Max 1.61mm
Solder Balls
96 Sn / 3.5 Ag / 0.5 Cu (VM package)
Ball diameter (typical)
0.40 mm
22.2
Mechanical Dimensions of the MPC8309 MAPBGA
Figure 44 shows the mechanical dimensions and bottom surface nomenclature of the MPC8309,
489-MAPBGA package.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
53
Package and Pin Listings
Figure 44. Mechanical Dimensions and Bottom Surface Nomenclature of the MPC8309 MAPBGA
Notes:
1. All dimensions are in millimeters.
2. Dimensions and tolerances per ASME Y14.5M-1994.
3. Maximum solder ball diameter measured parallel to datum A.
4. Datum A, the seating plane, is determined by the spherical crowns of the solder balls.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
54
Freescale Semiconductor
Package and Pin Listings
22.3
Pinout Listings
Following table shows the pin list of the MPC8309.
Table 55. MPC8309 Pinout Listing
Signal
Terminal
Pad Dir
Power Supply
Notes
DDR Memory Controller Interface
MEMC_MDQ0
U5
IO
GVDD
-
MEMC_MDQ1
AA1
IO
GVDD
-
MEMC_MDQ2
W3
IO
GVDD
-
MEMC_MDQ3
R5
IO
GVDD
-
MEMC_MDQ4
W2
IO
GVDD
-
MEMC_MDQ5
U3
IO
GVDD
-
MEMC_MDQ6
U2
IO
GVDD
-
MEMC_MDQ7
T3
IO
GVDD
-
MEMC_MDQ8
H3
IO
GVDD
-
MEMC_MDQ9
H4
IO
GVDD
-
MEMC_MDQ10
G3
IO
GVDD
-
MEMC_MDQ11
F3
IO
GVDD
-
MEMC_MDQ12
G5
IO
GVDD
-
MEMC_MDQ13
F4
IO
GVDD
-
MEMC_MDQ14
F5
IO
GVDD
-
MEMC_MDQ15
E3
IO
GVDD
-
MEMC_MDQ16
V4
IO
GVDD
-
MEMC_MDQ17
Y2
IO
GVDD
-
MEMC_MDQ18
Y1
IO
GVDD
-
MEMC_MDQ19
U4
IO
GVDD
-
MEMC_MDQ20
V1
IO
GVDD
-
MEMC_MDQ21
R4
IO
GVDD
-
MEMC_MDQ22
U1
IO
GVDD
-
MEMC_MDQ23
T2
IO
GVDD
-
MEMC_MDQ24
J5
IO
GVDD
-
MEMC_MDQ25
G2
IO
GVDD
-
MEMC_MDQ26
G1
IO
GVDD
-
MEMC_MDQ27
F1
IO
GVDD
-
MEMC_MDQ28
E2
IO
GVDD
-
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
55
Package and Pin Listings
MEMC_MDQ29
D2
IO
GVDD
-
MEMC_MDQ30
C2
IO
GVDD
-
MEMC_MDQ31
C1
IO
GVDD
-
MEMC_MECC0
Y5
IO
GVDD
-
MEMC_MECC1
AA4
IO
GVDD
-
MEMC_MECC2
Y4
IO
GVDD
-
MEMC_MECC3
AA3
IO
GVDD
-
MEMC_MECC4
AC2
IO
GVDD
-
MEMC_MECC5
AB2
IO
GVDD
-
MEMC_MECC6
Y3
IO
GVDD
-
MEMC_MECC7
AB1
IO
GVDD
-
MEMC_MDM0
W1
O
GVDD
-
MEMC_MDM1
E1
O
GVDD
-
MEMC_MDM2
V3
O
GVDD
-
MEMC_MDM3
D1
O
GVDD
-
MEMC_MDM8
W5
O
GVDD
-
MEMC_MDQS0
T5
IO
GVDD
-
MEMC_MDQS1
H5
IO
GVDD
-
MEMC_MDQS2
P5
IO
GVDD
-
MEMC_MDQS3
E5
IO
GVDD
-
MEMC_MDQS8
V5
IO
GVDD
-
MEMC_MBA0
K2
O
GVDD
-
MEMC_MBA1
K3
O
GVDD
-
MEMC_MBA2
N5
O
GVDD
-
MEMC_MA0
L3
O
GVDD
-
MEMC_MA1
L5
O
GVDD
-
MEMC_MA2
L2
O
GVDD
-
MEMC_MA3
L1
O
GVDD
-
MEMC_MA4
M3
O
GVDD
-
MEMC_MA5
M4
O
GVDD
-
MEMC_MA6
M1
O
GVDD
-
MEMC_MA7
N1
O
GVDD
-
MEMC_MA8
N2
O
GVDD
-
MEMC_MA9
N3
O
GVDD
-
MEMC_MA10
L4
O
GVDD
-
MEMC_MA11
P2
O
GVDD
-
MEMC_MA12
N4
O
GVDD
-
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
56
Freescale Semiconductor
Package and Pin Listings
MEMC_MA13
P1
O
GVDD
-
MEMC_MWE_B
J1
O
GVDD
-
MEMC_MRAS_B
K1
O
GVDD
-
MEMC_MCAS_B
J3
O
GVDD
-
MEMC_MCS_B0
J4
O
GVDD
-
MEMC_MCS_B1
K5
O
GVDD
-
MEMC_MCKE
P4
O
GVDD
-
MEMC_MCK0
R1
O
GVDD
-
MEMC_MCK1
R3
O
GVDD
-
MEMC_MCK_B0
T1
O
GVDD
-
MEMC_MCK_B1
P3
O
GVDD
-
MEMC_MODT0
H1
O
GVDD
-
MEMC_MODT1
H2
O
GVDD
-
MEMC_MVREF
M6
GVDD
-
Local Bus Controller Interface
LAD0
B5
IO
OVDD
-
LAD1
A4
IO
OVDD
-
LAD2
C7
IO
OVDD
-
LAD3
D9
IO
OVDD
-
LAD4
A5
IO
OVDD
-
LAD5
E10
IO
OVDD
-
LAD6
A6
IO
OVDD
-
LAD7
C8
IO
OVDD
-
LAD8
D10
IO
OVDD
-
LAD9
A7
IO
OVDD
-
LAD10
B7
IO
OVDD
-
LAD11
C9
IO
OVDD
-
LAD12
E11
IO
OVDD
-
LAD13
B8
IO
OVDD
-
LAD14
A8
IO
OVDD
-
LAD15
C10
IO
OVDD
-
LA16/ECID_TMODE_IN
C11
IO
OVDD
-
LA17
B10
O
OVDD
-
LA18
D12
O
OVDD
-
LA19
A9
O
OVDD
-
LA20
E12
O
OVDD
-
LA21
B11
O
OVDD
-
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
57
Package and Pin Listings
LA22
A11
O
OVDD
-
LA23
A10
O
OVDD
-
LA24
C12
O
OVDD
-
LA25
A12
O
OVDD
-
LCLK0
E13
O
OVDD
-
LCS_B0
D13
O
OVDD
2
LCS_B1
C13
O
OVDD
2
LCS_B2
A13
O
OVDD
2
LCS_B3
B13
O
OVDD
2
LWE_B0/LFWE_B0/LBS_B0
A14
O
OVDD
-
LWE_B1/LBS_B1
B14
O
OVDD
-
LBCTL
A15
O
OVDD
-
LGPL0/LFCLE
C14
O
OVDD
-
LGPL1/LFALE
C15
O
OVDD
-
LGPL2/LOE_B/LFRE_B
B16
O
OVDD
2
LGPL3/LFWP_B
A16
O
OVDD
-
LGPL4/LGTA_B/LUPWAIT/LFRB_B
E14
IO
OVDD
2
LGPL5
B17
O
OVDD
-
LALE
A17
O
OVDD
-
DUART
UART1_SOUT1
AB7
O
OVDD
-
UART1_SIN1
AC6
I
OVDD
-
UART1_SOUT2/UART1_RTS_B1/
W10
O
OVDD
-
Y9
I
OVDD
-
UART1_SIN2/UART1_CTS_B1/
I2C
IIC_SDA1
A20
IO
OVDD
1
IIC_SCL1
B20
IO
OVDD
1
IIC_SDA2 /CKSTOP_OUT_B/
D19
IO
OVDD
1
IIC_SCL2/CKSTOP_IN_B/
C20
IO
OVDD
1
Interrupts
IRQ_B0_MCP_IN_B
A21
IO
OVDD
-
IRQ_B1/MCP_OUT_B/
A22
IO
OVDD
-
IRQ_B2/CKSTOP_IN_B/
E18
I
OVDD
-
IRQ_B3/CKSTOP_OUT_B/INTA_B/
E19
IO
OVDD
-
IO
OVDD
-
SPI
SPIMOSI
B19
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
58
Freescale Semiconductor
Package and Pin Listings
SPIMISO
E16
IO
OVDD
-
SPICLK
E17
IO
OVDD
-
SPISEL
A19
I
OVDD
-
SPISEL_BOOT_B
D18
OVDD
-
JTAG
TCK
A2
I
OVDD
-
TDI
C5
I
OVDD
2
TDO
A3
O
OVDD
-
TMS
D7
I
OVDD
2
TRST_B
E9
I
OVDD
2
I
OVDD
-
Test Interface
TEST_MODE
C6
System Control Signals
HRESET_B
W23
IO
OVDD
1
PORESET_B
W22
I
OVDD
-
Clock Interface
QE_CLK_IN
R22
I
OVDD
-
SYS_CLK_IN
R23
I
OVDD
-
SYS_XTAL_IN
P23
I
OVDD
-
SYS_XTAL_OUT
P19
O
OVDD
-
PCI_SYNC_IN
T23
I
OVDD
-
PCI_SYNC_OUT
R20
O
OVDD
-
CFG_CLKIN_DIV_B
U23
I
OVDD
-
RTC_PIT_CLOCK
V23
I
OVDD
-
OVDD
-
Miscellaneous Signals
QUIESCE_B
D6
THERM0
E8
O
GPIO
GPIO_0/SD_CLK/MSRCID0 (DDR ID)
E4
IO
OVDD
-
GPIO_1/SD_CMD/MSRCID1 (DDR ID)
E6
IO
OVDD
-
GPIO_2/SD_CD/MSRCID2 (DDR ID)
D3
IO
OVDD
-
GPIO_3/SD_WP/MSRCID3 (DDR ID)
E7
IO
OVDD
-
GPIO_4/SD_DAT0/MSRCID4 (DDR ID)
D4
IO
OVDD
-
GPIO_5/SD_DAT1/MDVAL (DDR ID)
C4
IO
OVDD
-
GPIO_6/SD_DAT2/QE_EXT_REQ_3
B2
IO
OVDD
-
GPIO_7/SD_DAT3/QE_EXT_REQ_1
B3
IO
OVDD
-
GPIO_8/RXCAN1/LSRCID0/LCS_B4
C16
IO
OVDD
-
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
59
Package and Pin Listings
GPIO_9/TXCAN1/LSRCID1/LCS_B5
C17
IO
OVDD
-
GPIO_10/RXCAN2/LSRCID2/LCS_B6
E15
IO
OVDD
-
GPIO_11/TXCAN2/LSRCID3/LCS_B7
A18
IO
OVDD
-
GPIO_12/RXCAN3/LSRCID4/LCLK1
D15
IO
OVDD
-
GPIO_13/TXCAN3/LDVAL/
C18
IO
OVDD
-
GPIO_14/RXCAN4
D16
IO
OVDD
-
GPIO_15/TXCAN4
C19
IO
OVDD
-
USB
USBDR_PWRFAULT/CE_PIO_1/
AA6
I
OVDD
1
USBDR_CLK/UART2_SIN2/UART2_CTS_B1/
AC9
I
OVDD
-
USBDR_DIR/URM_TRIG/
AA7
I
OVDD
-
USBDR_NXT/UART2_SIN1/UC1_URM/QE_EXT
_REQ_4
AC5
I
OVDD
-
USBDR_TXDRXD0/GPIO_32/QE_TRB_O
Y6
IO
OVDD
-
USBDR_TXDRXD1/GPIO_33/QE_TRB_I
W9
IO
OVDD
-
USBDR_TXDRXD2/GPIO_34/QE_BRG_1
AB5
IO
OVDD
-
USBDR_TXDRXD3/GPIO_35/QE_BRG_2
AA5
IO
OVDD
-
USBDR_TXDRXD4/GPIO_36/QE_BRG_3
Y8
IO
OVDD
-
USBDR_TXDRXD5/GPIO_37/QE_BRG_4
AC4
IO
OVDD
-
USBDR_TXDRXD6/GPIO_38/QE_BRG_9
AC3
IO
OVDD
-
USBDR_TXDRXD7/GPIO_39/QE_BRG_11
AB3
IO
OVDD
-
USBDR_PCTL0/UART2_SOUT1/UC2_URM/LB_
POR_CFG_BOOT_ECC
W8
O
OVDD
-
USBDR_PCTL1/UART2_SOUT2/UART2_RTS_B
1/LB_POR_BOOT_ERR
W7
O
OVDD
-
USBDR_STP/UC3_URM/QE_EXT_REQ_2
W6
O
OVDD
-
PCI
PCI_INTA_B
B22
O
OVDD
-
PCI_RESET_OUT_B
F19
O
OVDD
-
PCI_AD0/BOOT_ROM_ADDR[2]
B23
IO
OVDD
-
PCI_AD1/BOOT_ROM_ADDR[3]
C21
IO
OVDD
-
PCI_AD2/BOOT_ROM_ADDR[4]
E20
IO
OVDD
-
PCI_AD3/BOOT_ROM_ADDR[5]
G19
IO
OVDD
-
PCI_AD4/BOOT_ROM_ADDR[6]
C23
IO
OVDD
-
PCI_AD5/BOOT_ROM_ADDR[7]
H19
IO
OVDD
-
PCI_AD6/CE_PIO_0/BOOT_ROM_ADDR[8]
D21
IO
OVDD
-
PCI_AD7/BOOT_ROM_ADDR[9]
F20
IO
OVDD
-
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
60
Freescale Semiconductor
Package and Pin Listings
PCI_AD8/BOOT_ROM_ADDR[10]
E21
IO
OVDD
-
PCI_AD9/BOOT_ROM_ADDR[11]
H20
IO
OVDD
-
PCI_AD10/BOOT_ROM_ADDR[12]
D22
IO
OVDD
-
PCI_AD11/BOOT_ROM_RDATA[0]
D23
IO
OVDD
-
PCI_AD12/BOOT_ROM_RDATA[1]
J19
IO
OVDD
-
PCI_AD13/BOOT_ROM_RDATA[2]
F21
IO
OVDD
-
PCI_AD14/BOOT_ROM_RDATA[3]
G21
IO
OVDD
-
PCI_AD15/BOOT_ROM_RDATA[4]
E22
IO
OVDD
-
PCI_AD16/BOOT_ROM_RDATA[5]
E23
IO
OVDD
-
PCI_AD17/BOOT_ROM_RDATA[6]
J20
IO
OVDD
-
PCI_AD18/BOOT_ROM_RDATA[7]
F23
IO
OVDD
-
PCI_AD19/BOOT_ROM_RDATA[8]
G23
IO
OVDD
-
PCI_AD20/BOOT_ROM_RDATA[9]
K19
IO
OVDD
-
PCI_AD21/BOOT_ROM_RDATA[10]
H21
IO
OVDD
-
PCI_AD22/BOOT_ROM_RDATA[11]
L19
IO
OVDD
-
PCI_AD23/BOOT_ROM_RDATA[12]
G22
IO
OVDD
-
PCI_AD24/BOOT_ROM_RDATA[13]
H23
IO
OVDD
-
PCI_AD25/BOOT_ROM_RDATA[14]
J21
IO
OVDD
-
PCI_AD26/UC5_URM/BOOT_ROM_RDATA[15]
H22
IO
OVDD
-
PCI_AD27BOOT_ROM_RDATA[16]
J23
IO
OVDD
-
PCI_AD28/UC7_URM/BOOT_ROM_RDATA[17]
K18
IO
OVDD
-
PCI_AD29/BOOT_ROM_RDATA[18]
K21
IO
OVDD
-
PCI_AD30/BOOT_ROM_RDATA[19]
K22
IO
OVDD
-
PCI_AD31/BOOT_ROM_RDATA[20]
K23
IO
OVDD
-
PCI_C_BE_B0 / BOOT_ROM_RDATA[21]
L20
IO
OVDD
-
PCI_C_BE_B1 / BOOT_ROM_RDATA[22]
L23
IO
OVDD
-
PCI_C_BE_B2 / BOOT_ROM_RDATA[23]
L22
IO
OVDD
-
PCI_C_BE_B3 / /BOOT_ROM_RDATA[24]
L21
IO
OVDD
-
PCI_PAR/BOOT_ROM_RDATA[25]
M19
IO
OVDD
-
PCI_FRAME_B / BOOT_ROM_RDATA[26]
M20
IO
OVDD
-
PCI_TRDY_B / BOOT_ROM_RDATA[27]
M23
IO
OVDD
-
PCI_IRDY_B / BOOT_ROM_RDATA[28]
M21
IO
OVDD
-
PCI_STOP_B / BOOT_ROM_RDATA[29]
N23
IO
OVDD
-
PCI_DEVSEL_B / BOOT_ROM_RDATA[30]
N22
IO
OVDD
-
PCI_IDSEL / BOOT_ROM_RDATA[31]
N21
IO
OVDD
-
PCI_SERR_B / BOOT_ROM_MOD_EN
N19
IO
OVDD
-
PCI_PERR_B / BOOT_ROM_RWB
P20
IO
OVDD
-
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
61
Package and Pin Listings
PCI_REQ_B0 / BOOT_ROM_XFR_WAIT
P21
IO
OVDD
-
PCI_REQ_B1/CPCI_HS_ES/BOOT_ROM_XFR_
ERR
P22
IO
OVDD
-
PCI_REQ_B2
T22
IO
OVDD
-
PCI_GNT_B0
T21
IO
OVDD
-
PCI_GNT_B1/CPCI_HS_LED/
U22
O
OVDD
-
PCI_GNT_B2/CPCI_HS_ENUM/
U21
IO
OVDD
-
M66EN
V21
I
OVDD
-
PCI_CLK0
T19
O
OVDD
-
PCI_CLK1
U19
O
OVDD
-
PCI_CLK2
R19
O
OVDD
-
Ethernet Management
FEC_MDC
W18
O
OVDD
-
FEC_MDIO
W17
IO
OVDD
-
Y18
IO
OVDD
-
FEC1_CRS/GTM1_TGATE1_B/GPIO_17/
AA19
IO
OVDD
-
FEC1_RX_CLK[CLK9]/GPIO_18/
W16
IO
OVDD
-
FEC1_RX_DV/GTM1_TIN2/GPIO_19/PLLCZ_C
ORE_CLKIN
AC22
IO
OVDD
-
FEC1_RX_ER/GTM1_TGATE2_B/GPIO_20/JTA
G_BISE
AA18
IO
OVDD
-
FEC1_RXD0/GPIO_21/JTAG_PRPGPS
AB20
IO
OVDD
-
FEC1_RXD1/GTM1_TIN3/GPIO_22/JTAG_BISR
_TDO_EN
Y17
IO
OVDD
-
FEC1_RXD2/GTM1_TGATE3_B/GPIO_23/TPR_
SYS_AAD[0]
AB19
IO
OVDD
-
FEC1_RXD3/GPIO_24/TPR_SYS_AAD[1]
AC21
IO
OVDD
-
FEC1_TX_CLK[CLK10]/GTM1_TIN4/GPIO_25/T
PR_SYS_AAD[2]
W15
IO
OVDD
-
FEC1_TX_EN/GTM1_TGATE4_B/GPIO_26/TPR
_SYS_AAD[3]
AC19
IO
OVDD
-
FEC1_TX_ER/GTM1_TOUT4_B/GPIO_27/TPR_
SYS_AAD[4]
AC20
IO
OVDD
-
FEC1_TXD0/GTM1_TOUT1_B/GPIO_28/TPR_S
YS_AAD[5]
AA17
IO
OVDD
-
FEC1_TXD1/GTM1_TOUT2_B/GPIO_29/TPR_S
YS_AAD[6]
AC18
IO
OVDD
-
FEC1_TXD2/GTM1_TOUT3_B/GPIO_30/TPR_S
YS_AAD[7]
AA16
IO
OVDD
-
FEC/GTM/GPIO
FEC1_COL/GTM1_TIN1/GPIO_16/
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
62
Freescale Semiconductor
Package and Pin Listings
FEC1_TXD3/GPIO_31/TPR_SYS_AAD[8]
AB17
IO
OVDD
-
FEC2_COL/GTM2_TIN1/GPIO_32/TPR_SYS_A
AD[9]
Y15
IO
OVDD
-
FEC2_CRS/GTM2_TGATE1_B/GPIO_33/TPR_S
YS_AAD[10]
AC17
IO
OVDD
-
FEC2_RX_CLK[CLK7]/GPIO_34/TPR_SYS_AAD
[11]
W14
IO
OVDD
-
FEC2_RX_DV/GTM2_TIN2/GPIO_35/TPR_SYS
_AAD[12]
AB16
IO
OVDD
-
FEC2_RX_ER/GTM2_TGATE2_B/GPIO_36/TPR
_SYS_AAD[13]
Y14
IO
OVDD
-
FEC2_RXD0/GPIO_37/TPR_SYS_AAD[14]
AA15
IO
OVDD
-
FEC2_RXD1/GTM2_TIN3/GPIO_38/TPR_SYS_
AAD[15]
AC15
IO
OVDD
-
FEC2_RXD2/GTM2_TGATE3_B/GPIO_39/TPR_
SYS_SYNC
AC16
IO
OVDD
-
FEC2_RXD3/GPIO_40/TPR_SYS_DACK
AA14
IO
OVDD
-
FEC2_TX_CLK[CLK8]/GTM2_TIN4/GPIO_41/
W13
IO
OVDD
-
FEC2_TX_EN/GTM2_TGATE4_B/GPIO_42/CLO
CK_XLB_CLOCK_OUT
AB14
IO
OVDD
-
FEC2_TX_ER/GTM2_TOUT4_B/GPIO_43/
AC14
IO
OVDD
-
Y12
IO
OVDD
-
FEC2_TXD1/GTM2_TOUT2_B/GPIO_45/
AA13
IO
OVDD
-
FEC2_TXD2/GTM2_TOUT3_B/GPIO_46/
AB13
IO
OVDD
-
FEC2_TXD3/GPIO_47/
AC13
IO
OVDD
-
FEC3_COL/GPIO_48/
AC12
IO
OVDD
-
FEC3_CRS/GPIO_49/
W11
IO
OVDD
-
FEC3_RX_CLK[CLK11]/GPIO_50/
W12
IO
OVDD
-
FEC3_RX_DV/FEC1_TMR_TX_ESFD/GPIO_51/
AA12
IO
OVDD
-
FEC3_RX_ER/FEC1_TMR_RX_ESFD/GPIO_52/
AB11
IO
OVDD
-
FEC3_RXD0/FEC3_TMR_TX_ESFD/GPIO_53/
AA11
IO
OVDD
-
FEC3_RXD1/FEC3_TMR_RX_ESFD/GPIO_54/
AC11
IO
OVDD
-
FEC3_RXD2/TSEC_TMR_TRIG1/GPIO_55/
Y11
IO
OVDD
-
FEC3_RXD3/TSEC_TMR_TRIG2/GPIO_56/
AB10
IO
OVDD
-
FEC3_TX_CLK[CLK12]/TSEC_TMR_CLK/GPIO
_57/
AC10
IO
OVDD
-
FEC3_TX_EN/TSEC_TMR_GCLK/GPIO_58/
AA10
IO
OVDD
-
FEC2_TXD0/GTM2_TOUT1_B/GPIO_44/PD_XL
B2MG_DDR_CLOCK
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
63
Package and Pin Listings
FEC3_TX_ER/TSEC_TMR_PP1/GPIO_59/
AC8
IO
OVDD
-
FEC3_TXD0/TSEC_TMR_PP2/GPIO_60/
AB8
IO
OVDD
-
FEC3_TXD1/TSEC_TMR_PP3/GPIO_61/
AA9
IO
OVDD
-
FEC3_TXD2/TSEC_TMR_ALARM1/GPIO_62/
AA8
IO
OVDD
-
FEC3_TXD3/TSEC_TMR_ALARM2/GPIO_63/
AC7
IO
OVDD
-
HDLC/TDM/GPIO
HDLC1_TXCLK[CLK16]/GPIO_0/QE_BRG_5/TD
M1_TCK[CLK4]
AA20
IO
OVDD
-
HDLC1_RXCLK[CLK15]/GPIO_1/TDM1_RCK
[CLK3]/
AA21
IO
OVDD
-
HDLC1_TXD/GPIO_2/TDM1_TD/CFG_RESET_
SOURCE[0]
AB22
IO
OVDD
1
HDLC1_RXD/GPIO_3/TDM1_RD/
AB23
IO
OVDD
-
HDLC1_CD_B/GPIO_4/TDM1_TFS/
W19
IO
OVDD
-
HDLC1_CTS_B/GPIO_5/TDM1_RFS/
V19
IO
OVDD
-
HDLC1_RTS_B/GPIO_6/TDM1_STROBE_B/CF
G_RESET_SOURCE[1]
AA23
IO
OVDD
-
HDLC2_TXCLK[CLK13]/GPIO_16/QE_BRG_7/T
DM2_TCK[CLK6]
Y20
IO
OVDD
-
HDLC2_RXCLK[CLK14]/GPIO_17/TDM2_RCK
[CLK5]/QE_BRG_8
Y22
IO
OVDD
-
HDLC2_TXD/GPIO_18/TDM2_TD/CFG_RESET
_SOURCE[2]
W20
IO
OVDD
1
HDLC2_RXD/GPIO_19/TDM2_RD/
W21
IO
OVDD
-
HDLC2_CD_B/GPIO_20/TDM2_TFS/
V20
IO
OVDD
-
HDLC2_CTS_B/GPIO_21/TDM2_RFS/
Y23
IO
OVDD
-
HDLC2_RTS_B/GPIO_22/TDM2_STROBE_B/C
FG_RESET_SOURCE[3]
U20
IO
OVDD
-
Power
AVDD1
L16
-
-
-
AVDD2
M16
-
-
-
AVDD3
N8
-
-
-
GVDD
F6, G6, H6, J6, K6, L6,
N6, P6, R6, T6, U6, V6,
V7
-
-
-
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
64
Freescale Semiconductor
Package and Pin Listings
NVDD
F7, F8, F9, F10, F11,
F12, F13,F14, F15, F16,
F17, F18, G18,H18, J18,
L18, M18, N18, P18,R18,
T18, U18, V8, V9, V10,
V11, V12, V13, V14, V15,
V16, V17, V18
-
-
-
VDD
H8,H9,H10,H11,H12,M8,
H13,N16,H14,H15,H16,
P16,P8,L8,K16,J16,K8,J
8,R8,T16,R16,T8,T9,T11
,T10,T12,T13,T14,T15
-
-
-
VSS
A1, C3, F22, J14, K14,
M15, L15, N20, R9, Y21,
T20, AB21, B1, C22,G4,
K15, J15, M2, M22, P9,
R10, V2, AA2, AC1,
B4,D5, G20, J22, K20,
M5, N9, P10, R11, V22,
AA22,AC23, B6, D8, J2,
K4, M9,L9, N10, P11,
R12, W4, AB4, D11, B9,
J9, K9, L10,M10, N11,
P12, R13, Y7,AB6, B12,
D14, J10, K10, L11, M11,
P13, N12, R14,
Y10,AB9, B15, D17, J11,
K11, D20, B18, J12, K12,
L13, L12, L14, K13, J13,
F2, B21, M14, M13, M12,
Y19, Y16, AB15, AB12,
Y13, N13, N14, N15,
P14, P15, R2, AB18,
R15, R21, T4
-
-
-
NC
A23
-
-
-
Notes
1. This pin is an open drain signal. A weak pull-up resistor should be placed on this pin to OVDD
2 This pin has weak pull-up that is always enabled.
4. OVDD here refers to NVDDA, NVDDB,NVDDC, NVDDF, NVDDG, and NVDDH from the ball map.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
65
Clocking
23 Clocking
Figure 45 shows the internal distribution of clocks within the MPC8309.
Figure 45. MPC8309 Clock Subsystem
MPC8309
e300c3 core
core_clk
Core PLL
Rest of the System
/n
csb_clk
to DDR
memory
controller
DDR
Clock
Divider
/2
MEMC_MCK
DDR
Memory
Device
MEMC_MCK
ddr_clk
Clock
Unit
System
PLL
lbc_clk
/n
to local bus
SYS_XTAL_OUT
CRYSTAL
csb_clk to rest
of the device
SYS_XTAL_IN
LBC
Clock
Divider
LCLK[0:1]
Local Bus
Memory
Device
PCI_SYNC_IN
SYS_CLK_IN
PCI_SYNC_OUT
PCI Clock Divider
PCI_CLK[0:2]
CFG_CLKIN_DIV
QE_CLK_IN
QE PLL
CLK Gen
qe_clk
QE Block
The primary clock source for the MPC8309 can be one of three inputs,Crystal(SYS_XTAL_IN ), SYS_CLK_IN
or PCI_SYNC_IN, depending on whether the device is configured in PCI host or PCI agent mode,
respectively.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
66
Freescale Semiconductor
Clocking
23.1
Clocking in PCI Host Mode
When the MPC8309 is configured as a PCI host device (RCWH[PCIHOST] = 1), SYS_CLK_IN is its
primary input clock. SYS_CLK_IN feeds the PCI clock divider (2) and the PCI_SYNC_OUT and
PCI_CLK multiplexors. The CFG_CLKIN_DIV configuration input selects whether SYS_CLK_IN or
SYS_CLK_IN/2 is driven out on the PCI_SYNC_OUT signal.
PCI_SYNC_OUT is connected externally to PCI_SYNC_IN to allow the internal clock subsystem to
synchronize to the system PCI clocks. PCI_SYNC_OUT must be connected properly to PCI_SYNC_IN,
with equal delay to all PCI agent devices in the system.
23.1.1
PCI Clock Outputs (PCI_CLK[0:2])
When the MPC8309 is configured as a PCI host, it provides three separate clock output signals,
PCI_CLK[0:2], for external PCI agents.
When the device comes out of reset, the PCI clock outputs are disabled and are actively driven to a steady
low state. Each of the individual clock outputs can be enabled (enable toggling of the clock) by setting its
corresponding OCCR[PCICOEn] bit. All output clocks are phase-aligned to each other.
23.2
Clocking in PCI Agent Mode
When the MPC8309 is configured as a PCI agent device, PCI_SYNC_IN is the primary input clock. In
agent mode, the SYS_CLK_IN signal should be tied to GND, and the clock output signals, PCI_CLKn and
PCI_SYNC_OUT, are not used.
23.3
System Clock Domains
As shown in Figure 45, the primary clock input (frequency) is multiplied up by the system phase-locked
loop (PLL) and the clock unit to create four major clock domains:
• The coherent system bus clock (csb_clk)
• The QUICC Engine clock (qe_clk)
• The internal clock for the DDR controller (ddr_clk)
• The internal clock for the local bus controller (lbc_clk)
The csb_clk frequency is derived from the following equation:
csb_clk = [PCI_SYNC_IN × (1 + ~CFG_CLKIN_DIV)] × SPMF
Eqn. 1
In PCI host mode,
PCI_SYNC_IN = SYS_CLK_IN (1 + ~CFG_CLKIN_DIV) .
Eqn. 2
The csb_clk serves as the clock input to the e300 core. A second PLL inside the core multiplies up the
csb_clk frequency to create the internal clock for the core (core_clk). The system and core PLL multipliers
are selected by the SPMF and COREPLL fields in the reset configuration word low (RCWL) which is
loaded at power-on reset or by one of the hard-coded reset options.For more information, see the Reset
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
67
Clocking
Configuration chapter in the MPC8309 PowerQUICC II Pro Communications Processor Reference
Manual.
The qe_clk frequency is determined by the QUICC Engine PLL multiplication factor (RCWL[CEPMF])
and the QUICC Engine PLL division factor (RCWL[CEPDF]) as the following equation:
qe_clk = (QE_CLK_IN × CEPMF)  (1 + CEPDF)
Eqn. 3
For more information, see the QUICC Engine PLL Multiplication Factor section and the “QUICC Engine
PLL Division Factor” section in the MPC8309 PowerQUICC II Pro Communications Processor
Reference Manual for more information.
The DDR SDRAM memory controller operates with a frequency equal to twice the frequency of csb_clk.
Note that ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider
(2) to create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate
is the same frequency as ddr_clk.
The local bus memory controller operates with a frequency equal to the frequency of csb_clk. Note that
lbc_clk is not the external local bus frequency; lbc_clk passes through the LBC clock divider to create the
external local bus clock outputs (LCLK). The LBC clock divider ratio is controlled by LCCR[CLKDIV].
For more information, see the LBC Bus Clock and Clock Ratios section in the MPC8309 PowerQUICC
II Pro Communications Processor Reference Manual.
In addition, some of the internal units may be required to be shut off or operate at lower frequency than
the csb_clk frequency. These units have a default clock ratio that can be configured by a memory mapped
register after the device comes out of reset.
Table 56 specifies which units have a configurable clock frequency. For detailed description, refer to the
“System Clock Control Register (SCCR)” section in the MPC8309 PowerQUICC II Pro Communications
Processor Reference Manual.
Table 56. Configurable Clock Units
Unit
Default Frequency
I2C,SDHC, USB, DMA Complex
csb_clk
Options
Off, csb_clk, csb_clk/2, csb_clk/3
NOTE
Setting the clock ratio of these units must be performed prior to any access
to them.
Table 57 provides the maximum operating frequencies for the MPC8309 MAPBGA under recommended
operating conditions (see Table 2).
Table 57. Operating Frequencies for MAPBGA
Characteristic1
Max Operating Frequency
Unit
e300 core frequency (core_clk)
417
MHz
Coherent system bus frequency (csb_clk)
167
MHz
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
68
Freescale Semiconductor
Clocking
Table 57. Operating Frequencies for MAPBGA (continued)
Characteristic1
QUICC Engine frequency (qe_clk)
2
DDR2 memory bus frequency (MCLK)
Local bus frequency
(LCLKn)3
Max Operating Frequency
Unit
233
MHz
167
MHz
66
MHz
1
The SYS_CLK_IN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen such that the resulting csb_clk,
MCLK, LCLK, and core_clk frequencies do not exceed their respective maximum or minimum operating frequencies.
2
The DDR2 data rate is 2× the DDR2 memory bus frequency.
3
The local bus frequency is 1/2, 1/4, or 1/8 of the lb_clk frequency (depending on LCCR[CLKDIV]) which is in turn 1× or 2× the
csb_clk frequency (depending on RCWL[LBCM]).
23.4
System PLL Configuration
The system PLL is controlled by the RCWL[SPMF] parameter. Table 58 shows the multiplication factor
encodings for the system PLL.
NOTE
System PLL VCO frequency = 2 × (CSB frequency) × (System PLL VCO
divider). The VCO divider needs to be set properly so that the System PLL
VCO frequency is in the range of 450–750 MHz.
Table 58. System PLL Multiplication Factors
RCWL[SPMF]
System PLL Multiplication Factor
0000
Reserved
0001
Reserved
0010
×2
0011
×3
0100
×4
0101
×5
0110
×6
0111–1111
Reserved
As described in Section 23, “Clocking,” the LBCM, DDRCM, and SPMF parameters in the reset
configuration word low select the ratio between the primary clock input (SYS_CLK_IN) and the internal
coherent system bus clock (csb_clk). Table 59 shows the expected frequency values for the CSB frequency
for selected csb_clk to SYS_CLK_IN ratios.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
69
Clocking
Table 59. CSB Frequency Options
PCI_SYNC_IN(MHz)
SPMF
csb_clk : sys_clk_in Ratio
25
33.33
66.67
csb_clk Frequency (MHz)
23.5
0010
2:1
0011
3:1
0100
4:1
0101
5:1
0110
6:1
133
133
125
167
Core PLL Configuration
RCWL[COREPLL] selects the ratio between the internal coherent system bus clock (csb_clk) and the e300
core clock (core_clk). Table 60 shows the encodings for RCWL[COREPLL]. COREPLL values not listed
in Table 60 should be considered reserved.
Table 60. e300 Core PLL Configuration
RCWL[COREPLL]
0-1
2-5
core_clk : csb_clk Ratio
VCO Divider
6
nn
0000
n
PLL bypassed
(PLL off, csb_clk clocks core directly)
PLL bypassed
(PLL off, csb_clk clocks core directly)
00
0001
0
1:1
2
01
0001
0
1:1
4
10
0001
0
1:1
8
11
0001
0
1:1
8
00
0001
1
1.5:1
2
01
0001
1
1.5:1
4
10
0001
1
1.5:1
8
11
0001
1
1.5:1
8
00
0010
0
2:1
2
01
0010
0
2:1
4
10
0010
0
2:1
8
11
0010
0
2:1
8
00
0010
1
2.5:1
2
01
0010
1
2.5:1
4
10
0010
1
2.5:1
8
11
0010
1
2.5:1
8
00
0011
0
3:1
2
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
70
Freescale Semiconductor
Clocking
Table 60. e300 Core PLL Configuration (continued)
RCWL[COREPLL]
0-1
2-5
core_clk : csb_clk Ratio
VCO Divider
6
01
0011
0
3:1
4
10
0011
0
3:1
8
11
0011
0
3:1
8
NOTE
Core VCO frequency = core frequency  VCO divider. The VCO divider
(RCWL[COREPLL[0:1]]), must be set properly so that the core VCO
frequency is in the range of 400–800 MHz.
23.6
QUICC Engine PLL Configuration
The QUICC Engine PLL is controlled by the RCWL[CEPMF] and RCWL[CEPDF] parameters. Table 61
shows the multiplication factor encodings for the QUICC Engine PLL.
Table 61. QUICC Engine PLL Multiplication Factors
RCWL[CEPMF]
RCWL[CEPDF]
QUICC Engine PLL Multiplication Factor = RCWL[CEPMF]/
(1 + RCWL[CEPDF)
00000–00001
0
Reserved
00010
0
2
00011
0
3
00100
0
4
00101
0
5
00110
0
6
00111
0
7
01000
0
8
01001–11111
0
Reserved
The RCWL[CEVCOD] denotes the QUICC Engine PLL VCO internal frequency as shown in Table 62.
Table 62. QUICC Engine PLL VCO Divider
RCWL[CEVCOD]
VCO Divider
00
2
01
4
10
8
11
Reserved
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
71
Clocking
NOTE
The VCO divider (RCWL[CEVCOD]) must be set properly so that the
QUICC Engine VCO frequency is in the range of 300–600 MHz. The
QUICC Engine frequency is not restricted by the CSB and core frequencies.
The CSB, core, and QUICC Engine frequencies should be selected
according to the performance requirements.
The QUICC Engine VCO frequency is derived from the following
equations:
qe_clk = (primary clock input × CEPMF)  (1 + CEPDF)
QUICC Engine VCO Frequency = qe_clk × VCO divider × (1 + CEPDF)
23.7
Suggested PLL Configurations
To simplify the PLL configurations, the MPC8309 might be separated into two clock domains. The first
domain contains the CSB PLL and the core PLL. The core PLL is connected serially to the CSB PLL, and
has the csb_clk as its input clock. The second clock domain has the QUICC Engine PLL. The clock
domains are independent, and each of their PLLs are configured separately.
Table 63 shows suggested PLL configurations for 33 and 66 MHz input clocks.
Table 63. Suggested PLL Configurations
CEDF
Input Clock
Frequency
(MHz)
CSB
Frequency
(MHz)
Core
Frequency
(MHz)
QUICC
Engine
Frequency
(MHz)
Conf No.
SPMF
Core
PLL
1
0100
0000100
0110
0
33.33
133.33
266.66
200
2
0100
0000101
1000
0
25
100
250
200
3
0010
0000100
0011
0
66.67
133.33
266.66
200
4
0100
0000101
0110
0
33.33
133.33
333.33
200
5
0101
0000101
1000
0
25
125
312.5
200
6
0010
0000101
0011
0
66.67
133.33
333.33
200
7
0100
0000110
0110
0
33.33
133.33
399.96
200
8
0101
0000110
1000
0
25
125
375
200
9
0010
0000110
0011
0
66.67
133.33
399.96
200
10
0101
0000101
0111
0
33.33
166.67
416.67
233
CEPMF
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
72
Freescale Semiconductor
Thermal
24 Thermal
This section describes the thermal specifications of the MPC8309.
24.1
Thermal Characteristics
Table 64 provides the package thermal characteristics for the 369, 19  19 mm MAPBGA of the
MPC8309.
Table 64. Package Thermal Characteristics for MAPBGA
Characteristic
Board type
Symbol
Value
Unit
Notes
Junction-to-ambient natural convection
Single-layer board (1s)
RJA
40
°C/W
1, 2
Junction-to-ambient natural convection
Four-layer board (2s2p)
RJA
25
°C/W
1, 2 ,3
Junction-to-ambient (@200 ft/min)
Single-layer board (1s)
RJMA
33
°C/W
1, 3
Junction-to-ambient (@200 ft/min)
Four-layer board (2s2p)
RJMA
22
°C/W
1, 3
Junction-to-board
—
RJB
15
°C/W
4
Junction-to-case
—
RJC
9
°C/W
5
Natural convection
JT
2
°C/W
6
Junction-to-package top
Notes:
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
2. Per JEDEC JESD51-2 with the single layer board horizontal. Board meets JESD51-9 specification.
3. Per JEDEC JESD51-6 with the board horizontal.
4. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method
1012.1).
6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature
per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.
24.1.1
Thermal Management Information
For the following sections, PD = (VDD  IDD) + PI/O, where PI/O is the power dissipation of the I/O
drivers.
24.1.2
Estimation of Junction Temperature with Junction-to-Ambient
Thermal Resistance
An estimation of the chip junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RJA  PD)
Eqn. 1
where:
TJ = junction temperature (C)
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
73
Thermal
TA = ambient temperature for the package (C)
RJA = junction-to-ambient thermal resistance (C/W)
PD = power dissipation in the package (W)
The junction-to-ambient thermal resistance is an industry standard value that provides a quick and easy
estimation of thermal performance. As a general statement, the value obtained on a single layer board is
appropriate for a tightly packed printed-circuit board. The value obtained on the board with the internal
planes is usually appropriate if the board has low power dissipation and the components are well separated.
Test cases have demonstrated that errors of a factor of two (in the quantity TJ – TA) are possible.
24.1.3
Estimation of Junction Temperature with Junction-to-Board
Thermal Resistance
The thermal performance of a device cannot be adequately predicted from the junction-to-ambient thermal
resistance. The thermal performance of any component is strongly dependent on the power dissipation of
surrounding components. In addition, the ambient temperature varies widely within the application. For
many natural convection and especially closed box applications, the board temperature at the perimeter
(edge) of the package is approximately the same as the local air temperature near the device. Specifying
the local ambient conditions explicitly as the board temperature provides a more precise description of the
local ambient conditions that determine the temperature of the device.
At a known board temperature, the junction temperature is estimated using the following equation:
TJ = TB + (RJB  PD)
Eqn. 2
where:
TJ = junction temperature (C)
TB = board temperature at the package perimeter (C)
RJB = junction-to-board thermal resistance (C/W) per JESD51-8
PD = power dissipation in package (W)
When the heat loss from the package case to the air can be ignored, acceptable predictions of junction
temperature can be made. The application board should be similar to the thermal test condition: the
component is soldered to a board with internal planes.
24.1.4
Experimental Determination of Junction Temperature
To determine the junction temperature of the device in the application after prototypes are available, the
thermal characterization parameter (JT) can be used to determine the junction temperature with a
measurement of the temperature at the top center of the package case using the following equation:
TJ = TT + (JT  PD)
Eqn. 3
where:
TJ = junction temperature (C)
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
74
Freescale Semiconductor
Thermal
TT = thermocouple temperature on top of package (C)
JT = thermal characterization parameter (C/W)
PD = power dissipation in package (W)
The thermal characterization parameter is measured per JESD51-2 specification using a 40 gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
24.1.5
Heat Sinks and Junction-to-Case Thermal Resistance
In some application environments, a heat sink is required to provide the necessary thermal management of
the device. When a heat sink is used, the thermal resistance is expressed as the sum of a junction-to-case
thermal resistance and a case to ambient thermal resistance as shown in the following equation:
RJA = RJC + RCA
Eqn. 4
where:
RJA = junction-to-ambient thermal resistance (C/W)
RJC = junction-to-case thermal resistance (C/W)
RCA = case-to-ambient thermal resistance (C/W)
RJC is device related and cannot be influenced by the user. The user controls the thermal environment to
change the case-to-ambient thermal resistance, RCA. For instance, the user can change the size of the heat
sink, the air flow around the device, the interface material, the mounting arrangement on printed-circuit
board, or change the thermal dissipation on the printed-circuit board surrounding the device.
To illustrate the thermal performance of the devices with heat sinks, the thermal performance has been
simulated with a few commercially available heat sinks. The heat sink choice is determined by the
application environment (temperature, air flow, adjacent component power dissipation) and the physical
space available. Because there is not a standard application environment, a standard heat sink is not
required.
Accurate thermal design requires thermal modeling of the application environment using computational
fluid dynamics software which can model both the conduction cooling and the convection cooling of the
air moving through the application. Simplified thermal models of the packages can be assembled using the
junction-to-case and junction-to-board thermal resistances listed in the thermal resistance table. More
detailed thermal models can be made available on request.
24.2
Heat Sink Attachment
When attaching heat sinks to these devices, an interface material is required. The best method is to use
thermal grease and a spring clip. The spring clip should connect to the printed-circuit board, either to the
board itself, to hooks soldered to the board, or to a plastic stiffener. Avoid attachment forces which would
lift the edge of the package or peel the package from the board. Such peeling forces reduce the solder joint
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
75
System Design Information
lifetime of the package. Recommended maximum force on the top of the package is 10 lb (4.5 kg) force.
If an adhesive attachment is planned, the adhesive should be intended for attachment to painted or plastic
surfaces and its performance verified under the application requirements.
24.2.1
Experimental Determination of the Junction Temperature with a
Heat Sink
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back calculate the case temperature using a separate measurement of the thermal resistance of the
interface.
From this case temperature, the junction temperature is determined from the junction-to-case thermal
resistance using the following equation:
TJ = TC + (RJC  PD)
Eqn. 5
where:
TC = case temperature of the package (C)
RJC = junction-to-case thermal resistance (C/W)
PD = power dissipation (W)
25 System Design Information
This section provides electrical and thermal design recommendations for successful application of the
MPC8309.
25.1
System Clocking
The MPC8309 includes three PLLs.
• The system PLL (AVDD2) generates the system clock from the externally supplied SYS_CLK_IN
input. The frequency ratio between the system and SYS_CLK_IN is selected using the system PLL
ratio configuration bits as described in Section 23.4, “System PLL Configuration.”
• The e300 core PLL (AVDD3) generates the core clock as a slave to the system clock. The frequency
ratio between the e300 core clock and the system clock is selected using the e300 PLL ratio
configuration bits as described in Section 23.5, “Core PLL Configuration.”
• The QUICC Engine PLL (AVDD1) which uses the same reference as the system PLL. The QUICC
Engine block generates or uses external sources for all required serial interface clocks.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
76
Freescale Semiconductor
System Design Information
25.2
PLL Power Supply Filtering
Each of the PLLs listed above is provided with power through independent power supply pins. The voltage
level at each AVDDn pin should always be equivalent to VDD, and preferably these voltages are derived
directly from VDD through a low frequency filter scheme such as the following.
There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to
provide independent filter circuits as illustrated in Figure 46, one to each of the three AVDD pins. By
providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the
other is reduced.
This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz
range. It should be built with surface mount capacitors with minimum effective series inductance (ESL).
Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook
of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a
single large value capacitor.
Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize
noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AVDD
pin, which is on the periphery of package, without the inductance of vias.
Figure 46 shows the PLL power supply filter circuit.
VDD
10
AVDD
2.2 µF
2.2 µF
Low ESL Surface Mount Capacitors (<0.5 nH)
GND
Figure 46. PLL Power Supply Filter Circuit
25.3
Decoupling Recommendations
Due to large address and data buses, and high operating frequencies, the MPC8309 can generate transient
power surges and high frequency noise in its power supply, especially while driving large capacitive loads.
This noise must be prevented from reaching other components in the MPC8309 system, and MPC8309
itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system
designer place at least one decoupling capacitor at each VDD, OVDD, and GVDD pins of the MPC8309.
These decoupling capacitors should receive their power from separate VDD, OVDD, GVDD, and GND
power planes in the PCB, utilizing short traces to minimize inductance. Capacitors may be placed directly
under the device using a standard escape pattern. Others may surround the part.
These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology)
capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the VDD, OVDD, and GVDD planes, to enable quick recharging of the smaller chip capacitors.
These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick
response time necessary. They should also be connected to the power and ground planes through two vias
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
77
System Design Information
to minimize inductance. Suggested bulk capacitors—100 to 330 µF (AVX TPS tantalum or Sanyo
OSCON).
25.4
Output Buffer DC Impedance
For all buses, the driver is a push-pull single-ended driver type (open drain for I2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD
or GND. Then, the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 47). The
output impedance is the average of two components, the resistances of the pull-up and pull-down devices.
When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals
OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each
other in value. Then, Z0 = (RP + RN)/2.
OVDD
RN
SW2
Data
Pad
SW1
RP
OGND
Figure 47. Driver Impedance Measurement
The value of this resistance and the strength of the driver’s current source can be found by making two
measurements. First, the output voltage is measured while driving logic 1 without an external differential
termination resistor. The measured voltage is V1 = Rsource  Isource. Second, the output voltage is measured
while driving logic 1 with an external precision differential termination resistor of value Rterm. The
measured voltage is V2 = (1/(1/R1 + 1/R2))  Isource. Solving for the output impedance gives
Rsource = Rterm  (V1/V2 – 1). The drive current is then Isource = V1/Rsource.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
78
Freescale Semiconductor
Ordering Information
Table 65 summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD,
nominal OVDD, 105C.
Table 65. Impedance Characteristics
Impedance
Local Bus, Ethernet, DUART, Control,
Configuration and Power Management
DDR DRAM
Symbol
Unit
RN
42 Target
20 Target
Z0
Ω
RP
42 Target
20 Target
Z0
Ω
Differential
NA
NA
ZDIFF
Ω
Note: Nominal supply voltages. See Table 1, Tj = 105C.
25.5
Configuration Pin Multiplexing
The MPC8309 provides the user with power-on configuration options which can be set through the use of
external pull-up or pull-down resistors of 4.7 k on certain output pins (Refer to the “Reset, Clocking
and Initialization” of MPC8309 PowerQUICC II Pro Integrated Communications Processor Family
Reference Manual). These pins are generally used as output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins
while HRESET is asserted, is latched when HRESET deasserts, at which time the input receiver is disabled
and the I/O circuit takes on its normal function. Careful board layout with stubless connections to these
pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should minimize
the disruption of signal quality or speed for output pins thus configured.
26 Ordering Information
This section presents ordering information for the devices discussed in this document, and it shows an
example of how the parts are marked. Ordering information for the devices fully covered by this document
is provided in Section 26.1, “Part Numbers Fully Addressed by This Document.”
26.1
Part Numbers Fully Addressed by This Document
Table 66 provides the Freescale part numbering nomenclature for the MPC8309 family. Note that the
individual part numbers correspond to a maximum processor core frequency. For available frequencies,
contact your local Freescale sales office. In addition to the maximum processor core frequency, the part
numbering scheme also includes the maximum effective DDR memory speed and QUICC Engine bus
frequency. Each part number also contains a revision code which refers to the die mask revision number.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
79
Ordering Information
Table 66. Part Numbering Nomenclature
MPC
nnnn
C
VM
AF
D
C
A
Product
Code
Part
Identifier
Temperature
Range1
Package2
e300 Core
Frequency3
DDR2
Frequency
QUICC
Engine
Frequency
Revision
Level
MPC
8309
VM = Pb-free
AD = 266 MHz
AF = 333 MHz
AG = 400 MHz
AH = 417MHz
D = 266 MHz
F = 333 MHz
C = 200 MHz
E = 233 MHz
Blank = 0 to
105C
C = –40 to
105C
Contact local
Freescale
sales office
Notes:
1. Contact local Freescale office on availability of parts with C temperature range.
2. See Section 22, “Package and Pin Listings,” for more information on available package types.
3. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this
specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other
maximum core frequencies.
26.2
Part Marking
Parts are marked as in the example shown in Figure 48.
MPCnnnnetppaaar
core/platform MHZ
ATWLYYWW
CCCCC
*MMMMM
YWWLAZ
MAPBGA
Notes:
ATWLYYWW is the traceability code.
CCCCC is the country code.
MMMMM is the mask number.
YWWLAZ is the assembly traceability code.
Figure 48. Freescale Part Marking for MAPBGA Devices
Table 67 shows the SVR Settings.
Table 67. SVR Settings
Device
MPC8309
Package
MAPBGA
SVR (Rev 1.0)
SVR (Rev 1.1)
0x8110_0010
0x8110_0011
Note: PVR = 0x8085_0020
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
80
Freescale Semiconductor
Document Revision History
27 Document Revision History
Table 68 provides a revision history for this hardware specification.
Table 68. Document Revision History
Rev.
No.
Date
0
03/2011
Substantive Change(s)
Initial Release.
MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0
Freescale Semiconductor
81
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1-800-521-6274 or
+1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0064
Japan
0120 191014 or
+81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
[email protected]
For Literature Requests Only:
Freescale Semiconductor
Literature Distribution Center
1-800 441-2447 or
+1-303-675-2140
Fax: +1-303-675-2150
LDCForFreescaleSemiconductor
@hibbertgroup.com
Document Number: MPC8309EC
Rev. 0
03/2011
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals” must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale, the Freescale logo, CodeWarrior, ColdFire, PowerQUICC,
StarCore, and Symphony are trademarks of Freescale Semiconductor, Inc.
Reg. U.S. Pat. & Tm. Off. CoreNet, QorIQ, QUICC Engine, and VortiQa are
trademarks of Freescale Semiconductor, Inc. All other product or service
names are the property of their respective owners. The Power Architecture
and Power.org word marks and the Power and Power.org logos and related
marks are trademarks and service marks licensed by Power.org. RapidIO is
a registered trademark of the RapidIO Trade Association. IEEE 802.11i,
1588, 802.3 and 1149.1 are registered trademarks of the Institute of Electrical
and Electronics Engineers, Inc. (IEEE). This product is not endorsed or
approved by the IEEE.
© 2011 Freescale Semiconductor, Inc.