FREESCALE MPC8569E

Freescale Semiconductor
Data Sheet: Technical Data
Document Number: MPC8569EEC
Rev. 1, 02/2012
MPC8569E
MPC8569E PowerQUICC III
Integrated Processor
Hardware Specifications
• High-performance, 32-bit e500 core, scaling up to
1.33 GHz, that implements the Power Architecture®
technology
– 2799 MIPS at 1.33 GHz (estimated Dhrystone 2.1)
– 36-bit physical addressing
– Double-precision embedded floating point APU using
64-bit operands
– Embedded vector and scalar single-precision
floating-point APUs using 32- or 64-bit operands
– Memory management unit (MMU)
• Integrated L1/L2 cache
– L1 cache—32-Kbyte data and 32-Kbyte instruction
– L2 cache—512-Kbyte (8-way set associative)
• Two DDR2/DDR3 SDRAM memory controllers with full
ECC support
– One 64-bit or two 32-bit data bus configuration
– Up to 400 MHz clock (800 MHz data rate)
– Supporting up to 16 Gbytes of main memory
– Using ECC, detects and corrects all single-bit errors and
detects all double-bit errors and all errors within a nibble
– Invoke a level of system power management by
asserting MCKE SDRAM signal on-the-fly to put the
memory into a low-power sleep mode
– Both hardware and software options to support
battery-backed main memory
– Initialization bypass feature that allow system designers
to prevent re-initialization of main memory during
system power on following abnormal shutdown
• Integrated security engine (SEC) optimized to process all
the algorithms associated with IPsec, IKE, SSL/TLS,
iSCSI, SRTP, IEEE Std 802.11i™, IEEE Std 802.16™
(WiMAX), IEEE 802.1ae™ (MACSec), 3GPP, A5/3 for
GSM and EDGE, and GEA3 for GPRS.
– XOR engine for parity checking in RAID storage
applications
– Four crypto-channels, each supporting multi-command
descriptor chains
Freescale reserves the right to change the detail specifications as may be required
to permit improvements in the design of its products.
© 2008–2012 Freescale Semiconductor, Inc. All rights reserved.
FC–PBGA–783
29 mm × 29 mm
•
•
•
•
•
•
•
•
•
•
•
– Cryptographic execution units for PKEU, DEU, AESU,
AFEU, MDEU, KEU, CRCU, RNG and SEU- SNOW
QUICC Engine technology
– Four 32-bit RISC cores
– Supports Ethernet, ATM, POS, and T1/E1 along with
associated interworking
– Four Gigabit Ethernet interfaces (up to two with
SGMII)
– Up to eight 10/100-Mbps Ethernet interfaces
– Up to 16 T1/E1 TDM links (512 × 64 channels)
– Multi-PHY UTOPIA/POS-PHY L2 interface
(16-bit)
– IEEE Std 1588™ v2 support
– SPI and Ethernet PHY management interface
– One full-/low-speed USB interface supporting USB 2.0
– General-purpose I/O signals
High-speed interfaces (multiplexed) supporting:
– Two 1× Serial RapidIO interfaces (with message unit) or
one 4x interface
– ×4/×2/×1 PCI Express interface
– Two SGMII interfaces
On-chip network switch fabric
133 MHz, 16-bit, 3.3 V I/O, enhanced local bus (eLBC)
with memory controller
Enhanced secured digital host controller (eSDHC) used for
SD/MMC card interface
Integrated four-channel DMA controller
Dual I2C and dual universal asynchronous
receiver/transmitter (DUART) support
Programmable interrupt controller (PIC)
IEEE Std 1149.1™ JTAG test access port
1.0-V and 1.1-V core voltages with 3.3-V, 2.5-V, 1.8-V,
1.5-V and 1.0-V I/O
783-pin FC-PBGA package, 29 mm × 29 mm
Table of Contents
1
2
Pin Assignments and Reset States . . . . . . . . . . . . . . . . . . . . .4
1.1 Ball Layout Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2 Pinout List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
2.1 Overall DC Electrical Characteristics . . . . . . . . . . . . . .36
2.2 Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . .42
2.3 Input Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
2.4 DDR2 and DDR3 SDRAM Controller . . . . . . . . . . . . . .45
2.5 DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
2.6 Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
2.7 Ethernet Management Interface . . . . . . . . . . . . . . . . . .74
2.8 HDLC, BISYNC, Transparent, and Synchronous UART
Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
2.9 High-Speed SerDes Interfaces (HSSI) . . . . . . . . . . . . .78
2.10 PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
2.11 Serial RapidIO (SRIO) . . . . . . . . . . . . . . . . . . . . . . . . .90
2.12 I2C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
2.13 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
2.14 JTAG Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
2.15 Enhanced Local Bus Controller . . . . . . . . . . . . . . . . .101
2.16 Enhanced Secure Digital Host Controller (eSDHC) . .108
3
4
5
6
7
2.17 Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
2.18 Programmable Interrupt Controller (PIC). . . . . . . . . . 111
2.19 SPI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
2.20 TDM/SI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
2.21 USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
2.22 UTOPIA/POS Interface . . . . . . . . . . . . . . . . . . . . . . . 117
Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
3.1 Thermal Characteristics. . . . . . . . . . . . . . . . . . . . . . . 119
3.2 Recommended Thermal Model . . . . . . . . . . . . . . . . . 119
3.3 Thermal Management Information . . . . . . . . . . . . . . 120
Package Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
4.1 Package Parameters for the MPC8569E . . . . . . . . . . 122
4.2 Mechanical Dimensions of the FC-PBGA with Full Lid123
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
5.1 Part Numbers Fully Addressed by This Document . . 124
5.2 Part Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
5.3 Part Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Product Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . 126
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
2
Freescale Semiconductor
NOTE
The MPC8569E is also available without a security engine in a configuration known as the
MPC8569. All specifications other than those relating to security apply to the MPC8569
exactly as described in this document.
The following figure shows the major functional units within the MPC8569E.
e500v2 Core
MPC8569E
32-Kbyte
I-Cache
XOR
Acceleration
Performance
Monitor
DUART
2 × I2C
Enhanced
Local
Bus
Security
Engine
OpenPIC
32-Kbyte
D-Cache
e500
Coherency
Module
QUICC Engine Block
Accelerators
Baud Rate
Generators
256-Kbyte
IRAM
128-Kbyte
MURAM
One 64-bit or
Two 32-bit
DDR2/DDR3
Controller(s)
Enhanced
Secure
Digital Controller
Serial DMA
Four 32-bit eRISCs
512-Kbyte
L2
Cache
Interrupt
Controller
4-Channel DMA
Up To
16 T1/E1
UTOPIA/
POS-PHY L2
Up To
8 RMII
Up To
4 Gigabit Ethernet
PCI Express
Serial RapidIO
Serial RapidIO
SGMII
Four-Lane SerDes
Communications Interfaces
On-Chip Network
USB
SPI1 & 2
Eth Mgmt
Time Slot Assigner
UCC8
UCC7
UCC6
UCC5
UCC4
UCC3
UCC2
UCC1
MCC2
MCC1
RIO Msg Unit
SGMII
Figure 1. MPC8569E Block Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
3
Ball Layout Diagrams
1
Pin Assignments and Reset States
1.1
Ball Layout Diagrams
The following figure shows the top view of the MPC8569E 783-pin BGA ball map diagram.
1
A
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
D2_
MCKE
[3]
D2_
MODT
[1]
D2_
MA
[1]
D2_
MA
[11]
D2_
MCS
[1]
D2_
MDQ
[31]
D2_
MDQ
[30]
D2_
MDM
[3]
D2_
MDQ
[29]
D2_
MDQ
[7]
D2_
MDQ
[6]
D2_
MDM
[0]
D2_
MDQ
[5]
D1_
MA
[13]
D1_
MCKE
[3]
D1_
MDIC
[1]
D1_
MA
[1]
D1_
MA
[11]
D1_
MDIC
[0]
D1_
MDQ
[31]
D1_
MDQ
[30]
D1_
MDM
[3]
D1_
MDQ
[29]
D1_
MDQ
[7]
D1_
MDQ
[6]
D1_
MDM
[0]
D1_
MDQ
[5]
A
GND
D2_
MA
[4]
GVDD
GND
D2_
MDQ
[27]
GVDD
GND
D2_
MDQ
[28]
D2_
MDQ
[3]
GVDD
GND
D2_
MDQ
[0]
D2_
MDQ
[4]
GVDD
GND
D1_
MA
[4]
GVDD
GND
D1_
MDQ
[27]
GVDD
GND
D1_
MDQ
[28]
D1_
MDQ
[3]
GVDD
GND
D1_
MDQ
[4]
B
GND
D2_
MCK
[2]
D2_
MCK
[2]
D2_
MDQ
[26]
D2_
MDQ
[25]
D2_
MDQS
[3]
D2_
MDQ
[24]
D2_
MDQ
[2]
D2_
MDQS
[0]
D2_
MDQS
[0]
D2_
MDQ
[1]
D1_
MA
[15]
D1_
MODT
[0]
D1_
MCKE
[2]
D1_
MA
[6]
D1_
MCK
[2]
D1_
MCK
[2]
D1_
MDQ
[26]
D1_
MDQ
[25]
D1_
MDQS
[3]
D1_
MDQ
[24]
D1_
MDQ
[2]
D1_
MDQS
[0]
D1_
MDQ
[1]
D1_
MDQ
[0]
C
D2_
MECC
[7]
D2_
MECC
[5]
D2_
MDQS
[3]
GVDD
GND
D2_
MDQ
[14]
D2_
MDM
[1]
D2_
MDQ
[13]
GVDD
GND
D1_
MCS
[0]
GVDD
GND
D1_
MA
[14]
D1_
MECC
[7]
D1_
MECC
[5]
D1_
MDQS
[3]
GVDD
GND
D1_
MDQS
[0]
GVDD
GND
D
D2_
MDM
[8]
D2_
MCK
[0]
D2_
MCK
[0]
D2_
MDQ
[15]
GVDD
GND
D2_
MDQ
[12]
D1_
MAPAR_
OUT
D1_
MODT
[3]
D1_
MWE
D1_
MA
[0]
D1_
MA
[8]
D1_
MBA
[2]
D1_
MECC
[6]
D1_
MDM
[8]
D1_
MCK
[0]
D1_
MCK
[0]
D1_
MDQ
[15]
D1_
MDQ
[14]
D1_
MDM
[1]
D1_
MDQ
[13]
E
GVDD
GND
D2_
MECC
[4]
D2_
MDQ
[11]
D2_
MDQS
[1]
D2_
MDQ
[9]
D2_
MDQ
[8]
D1_
MAPAR_
ERR
GVDD
GND
D1_
MBA
[1]
GND
D1_
MECC
[3]
GVDD
GND
D1_
MECC
[4]
D1_
MDQ
[11]
GVDD
GND
D1_
MDQ
[12]
F
D2_
MDM
[2]
D2_
MDQ
[21]
D1_
MCS
[3]
D1_
MCKE
[0]
D1_
MECC
[2]
D1_
MDQS
[8]
D1_
MDQ
[10]
D1_
MDQS
[1]
D1_
MDQ
[9]
D1_
MDQ
[8]
G
GVDD
GVDD
GND
D1_
MECC
[1]
D1_
MDQS
[8]
GVDD
GND
D1_
MDQS
[1]
GVDD
GND
H
GVDD
D1_
MCKE
[1]
D1_
MA
[7]
D1_
MA
[12]
D1_
MCK
[1]
D1_
MCK
[1]
D1_
MDQ
[23]
D1_
MDQ
[22]
D1_
MDM
[2]
D1_
MDQ
[21]
J
GND
D1_
MCS
[2]
GVDD
D1_
MDQ
[18]
D1_
MDQS
[2]
D1_
MDQ
[19]
GVDD
GND
D1_
MDQ
[20]
K
GVDD
GND
D1_
MDQS
[2]
D1_
MDQ
[17]
D1_
MDQ
[16]
GND
L
ASLEEP
CLK_
OUT
M
B
D2_
MA
[15]
GVDD
C
D2_
MODT
[0]
D2_
MCKE
[2]
GVDD
D
GVDD
GND
D2_
MA
[13]
GVDD
GND
D2_
MA
[14]
E
D2_
MODT
[3]
D2_
MWE
D2_
MCS
[0]
D2_
MA
[0]
D2_
MA
[8]
D2_
MBA
[2]
D2_
MECC
[6]
F
D2_
MAPAR_
OUT
GVDD
GND
D2_
MBA
[1]
GND
D2_
MECC
[3]
G
D2_
MAPAR_
ERR
D2_
MCS
[3]
D2_
MA
[6]
D2_
MRAS
GND
GVDD
D2_
MODT
[2]
D2_
MA
[5]
D2_
MVREF
D2_
MDIC
[0]
D2_
MCAS
H
J
GVDD
GVDD
D2_
MA
[3]
D2_
MCKE
[0]
D2_
MECC
[2]
D2_
MDQS
[8]
GVDD
GND
D2_
MCS
[2]
D2_
MECC
[1]
D2_
MDQS
[8]
D2_
MBA
[0]
D2_
MA
[10]
D2_
MA
[2]
D2_
MA
[7]
D2_
MA
[12]
D2_
MCKE
[1]
D2_
MA
[9]
SEE DETAIL A
K
AVDD_
CE
GND
GVDD
GVDD
GND
GVDD
GND
L
AVDD_
CORE
D2_
MDIC
[1]
QE_PC
[3]
QE_PA
[22]
QE_PA
[18]
QE_PA
[15]
QE_PC
[16]
LVDD2
QE_PA
[23]
QE_PA
[20]
QE_PA
[16]
LVDD2
M
N
GND
QE_PA
[24]
GND
QE_PA
[28]
QE_PC
[2]
P
QE_PA
[19]
QE_PB
[17]
QE_PC
[25]
R
QE_PA
[25]
QE_PB
[23]
T
QE_PA
[27]
U
QE_PA
[26]
QE_PA
[21]
QE_PB
[9]
QE_PB
[1]
QE_PC
[9]
QE_PB
[22]
QE_PE
[22]
QE_PA
[17]
GND
D2_
MDQS
[1]
GVDD
GND
D2_
MDQ
[23]
GVDD
GND
D2_
MDQ
[20]
D2_
MCK
[1]
D2_
MCK
[1]
D2_
MDQ
[19]
D2_
MDQS
[2]
D2_
MDQ
[17]
D2_
MDQ
[16]
D1_
MODT
[1]
GND
D2_
MDQ
[18]
D2_
MDQS
[2]
GND
D1_
MCS
[1]
D1_
MBA
[0]
GVDD
GVDD
GVDD
GND
GND
QE_PB
[18]
QE_PB
[12]
QE_PC
[17]
QE_PB
[19]
LVDD2
QE_PB
[13]
QE_PC
[24]
QE_PB
[20]
D2_
MDQ
[22]
D2_
MDQ
[10]
D2_
MECC
[0]
GND
QE_PB
[14]
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
GVDD
GND
VDD
SENSE- SENSEVDD
VSS
GND
VDD
GND
GVDD
D1_
MODT
[2]
D1_
MRAS
D1_
MA
[9]
GND
D1_
MA
[5]
D1_
MA
[2]
D1_
MCAS
D1_
MA
[10]
VDD
GND
VDD
GVDD
GND
VDD
GND
D1_
MA
[3]
VDD
GND
GND
IRQ_
OUT
VDD
IRQ4_
MSRCID
[3]
GND
GND
IRQ
[1]
Rsvd
SD_TX
[0]
SD_TX
[0]
SCORE- SCOREVDD
GND
SD_RX
[0]
VDD
GND
VDD
Rsvd
Rsvd
GND
XVDD
XGND
AGND_
SRDS
XGND
SD_TX
[1]
SD_TX
[1]
SCORE- SCOREVDD
GND
XGND
XVDD
SD_REF_ SD_REF_ SCORE- SCOREVDD
GND
CLK
CLK
W
SD_TX
[2]
SD_TX
[2]
SCORE- SCOREVDD
GND
Y
XGND
SD_IMP_ SD_PLL_ SCORE- SCOREVDD
CAL_TX
TPA
GND
AA
SD_RX
[3]
AB
HRESET_ SCORE- SCOREVDD
GND
REQ
AC
VDD
GND
VDD
GND
VDD
QE_PB
[3]
GND
QE_PA
[31]
GND
QE_PC
[8]
QE_PA
[8]
GND
LVDD1
QE_PA
[0]
VDD
GND
VDD
GND
VDD
QE_PB
[25]
QE_PB
[4]
QE_PB
[5]
QE_PB
[6]
QE_PA
[30]
QE_PC
[20]
QE_PA
[9]
QE_PA
[7]
QE_PA
[3]
QE_PA
[1]
GND
VDD
GND
VDD
GND
V
QE_PE
[14]
QE_PE
[17]
QE_PB
[7]
QE_PB
[8]
QE_PB
[10]
QE_PB
[2]
QE_PC
[29]
QE_PA
[13]
QE_PA
[11]
QE_PA
[10]
QE_PA
[5]
VDD
GND
VDD
GND
VDD
GND
VDD
GND
GND
W
QE_PE
[16]
QE_PC
[5]
QE_PC
[0]
QE_PC
[1]
QE_PC
[6]
OVDD
QE_PC
[7]
QE_PC
[26]
QE_PC
[27]
OVDD
QE_PB
[11]
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
Y
QE_PE
[11]
OVDD
QE_PC
[22]
QE_PC
[23]
QE_PC
[19]
GND
QE_PC
[4]
QE_PD
[18]
QE_PD
[26]
GND
QE_PD
[21]
VDD
GND
VDD
GND
GND
GND
VDD
GND
AA
AB
QE_PC
[21]
AC
QE_PE
[12]
AD
QE_PE
[21]
AE
QE_PE
[23]
AF
QE_PD
[28]
GND
QE_PC
[10]
QE_PC
[18]
QE_PE
[15]
QE_PD
[10]
QE_PE
[13]
QE_PE
[18]
QE_PD
[11]
SEE DETAIL C
OVDD
QE_PD
[6]
QE_PD
[8]
QE_PD
[15]
QE_PD
[14]
QE_PD
[16]
QE_PB
[28]
OVDD
GND
QE_PD
[20]
QE_PC
[31]
QE_PC
[30]
QE_PD
[25]
QE_PD
[23]
QE_PE
[25]
QE_PE
[26]
LDP
[0]
QE_PF
[10]
QE_PE
[19]
QE_PE
[20]
QE_PD
[5]
GND
QE_PD
[9]
QE_PD
[7]
QE_PB
[29]
QE_PB
[30]
QE_PB
[31]
OVDD
QE_PE
[5]
QE_PD
[4]
QE_PD
[12]
QE_PD
[13]
QE_PE
[31]
QE_PF
[2]
QE_PF
[16]
QE_PF
[15]
GND
QE_PE
[4]
QE_PE
[2]
QE_PD
[3]
QE_PD
[1]
OVDD
QE_PF
[0]
QE_PF
[17]
QE_PF
[18]
QE_PF
[11]
QE_PE
[24]
QE_PF
[4]
LCS
[3]
QE_PF
[12]
QE_PF
[9]
QE_PF
[5]
LCS4_
IRQ
[8]
OVDD
QE_PF
[7]
QE_PF
[3]
LA
[18]
GND
QE_PF
[6]
QE_PC
[28]
LAD
[1]
AG
QE_PD
[29]
QE_PD
[30]
QE_PE
[6]
QE_PE
[3]
QE_PE
[9]
QE_PD
[2]
GND
QE_PF
[1]
QE_PF
[21]
QE_PE
[28]
QE_PE
[30]
QE_PF
[8]
QE_PB
[26]
LAD
[0]
AH
QE_PD
[31]
QE_PE
[0]
QE_PE
[1]
QE_PE
[8]
QE_PE
[7]
QE_PD
[0]
QE_PF
[20]
QE_PF
[19]
QE_PF
[22]
QE_PE
[29]
QE_PE
[27]
QE_PF
[13]
QE_PF
[14]
QE_PB
[27]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
LDP
[1]
LGPL
[5]
GND
LCS
[2]
BVDD
LCS
[1]
GND
VDD
LGPL4_
LGPL1_ LUPWAIT_ LGPL0_
LFALE LBPBSE_ LFCLE
LFRB
LWE1_
GND
GND
LBS
[1]
BVDD
LCS
[0]
GND
LWE0_
LBS0_
LFWE
LBCTL
LA
[24]
LA
[26]
LAD
[13]
15
16
BVDD
XGND
LA
[27]
LA
[22]
LSYNC_ LSYNC_
OUT
IN
XGND
LCS7_
IRQ
[11]
LAD
[12]
LA
[20]
LAD
[2]
XVDD
LCS6_
IRQ
[10]
LA
[23]
BVDD
GND
LAD
[6]
GND
LAD
[3]
LAD
[4]
17
18
XVDD
SD_TX
[3]
LAD
[15]
LA
[21]
GND
XVDD
LA
[25]
LA
[19]
LCLK
[0]
XGND
BVDD
LA
[17]
BVDD
SD_PLL_ SD_IMP_
TPD
CAL_RX
SEE DETAIL D
LA
[16]
LCLK
[1]
XVDD
LGPL3_ SD_TX_ SD_TX_
CLK
CLK
LFWP
LGPL2_
LOE_
LFRE
BVDD
P
VDD
GND
QE_PD
[22]
GND
GND
QE_PA
[2]
QE_PD
[27]
GND
LVDD_
VSEL
[1]
GND
XGND
QE_PA
[4]
QE_PD
[17]
N
TRIG_IN
TRIG_OUT_
TDO _READY__ SYSCLK
QUIESCE
XVDD
QE_PA
[6]
QE_PD
[19]
AVDD_
PLAT
OVDD
VDD
LVDD1
QE_PA
[12]
QE_PD
[24]
D1_
MVREF
TMS
GND
LVDD1
QE_PC
[11]
QE_PC
[12]
GND
TRST
QE_PB
[0]
QE_PC
[14]
OVDD
BVDD_
VSEL
[0]
IRQ6_
DVAL
QE_PB
[15]
QE_PC
[15]
RTC
TDI
QE_PB
[16]
QE_PC
[13]
TCK
MCP
AVDD_
DDR
IRQ5_
MSRCID
[4]
QE_PB
[21]
QE_PE
[10]
UDE
GND
IRQ
[0]
QE_PB
[24]
VDD
GVDD
GND
QE_PA
[14]
GND
GND
BVDD_
VSEL
[1]
QE_PA
[29]
VDD
D1_
MECC
[0]
SEE DETAIL B
LAD
[7]
BVDD
LAD
[14]
IRQ
[3]
SD_TX
[3]
XGND
XVDD
SRESET
IRQ
[2]
AVDD_
SRDS
GND
LAD
[8]
GND
LAD
[11]
LAD
[5]
LALE
LAD
[9]
LAD
[10]
GND
AVDD_
LBIU
19
20
21
22
23
24
IIC1_
SCL
GND
IIC1_
SDA
25
26
SD_RX
[0]
T
SCORE- SCOREVDD
GND
U
SD_RX
[1]
V
SD_RX
[2]
SCOREGND
IIC2_
SDA_SD_
CLK
R
SD_RX
[1]
SD_RX
[3]
DMA_
DMA_
DMA_
HRESET DACK2_ DDONE_ DREQ2_
SD_CMD
SD_DAT0
[0]
DMA_
DMA_
LCS5_
GND
IRQ DDONE1_ DREQ1_
[9]
MSRCID2 MSRCID0
DMA_
DMA_
IIC2_
OVDD DDONE2_ SCL_SD_
DACK_
SD_WP
CD
[0]
DMA_
DREQ_
[0]
SCORE- SCOREVDD
GND
SD_RX
[2]
DMA_
DACK1_
MSRCID1
LVDD_
VSEL
[0]
AD
OVDD
CKSTP_
IN
AE
UART_
SIN0_DMA CKSTP_
_DACK3_ OUT
SD_DAT2
UART_
UART_
CTS0_DMA SOUT0_DMA
_DDONE3_ _DREQ3_
SD_DAT1
SD_DAT3
LSSD_ UART_
RTS
MODE
[0]
27
AF
AG
AH
28
Figure 2. MPC8569E Top View Ballmap
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
4
Freescale Semiconductor
Ball Layout Diagrams
The following figure provides detailed view A of the MPC8569E 783-pin BGA ball map diagram.
1
A
2
3
4
5
6
7
8
9
10
11
12
13
14
D2_
MCKE
[3]
D2_
MODT
[1]
D2_
MA
[1]
D2_
MA
[11]
D2_
MCS
[1]
D2_
MDQ
[31]
D2_
MDQ
[30]
D2_
MDM
[3]
D2_
MDQ
[29]
D2_
MDQ
[7]
D2_
MDQ
[6]
D2_
MDM
[0]
D2_
MDQ
[5]
B
D2_
MA
[15]
GVDD
GND
D2_
MA
[4]
GVDD
GND
D2_
MDQ
[27]
GVDD
GND
D2_
MDQ
[28]
D2_
MDQ
[3]
GVDD
GND
D2_
MDQ
[0]
C
D2_
MODT
[0]
D2_
MCKE
[2]
GVDD
GND
D2_
MCK
[2]
D2_
MCK
[2]
D2_
MDQ
[26]
D2_
MDQ
[25]
D2_
MDQS
[3]
D2_
MDQ
[24]
D2_
MDQ
[2]
D2_
MDQS
[0]
D2_
MDQS
[0]
D2_
MDQ
[1]
D
GVDD
GND
D2_
MA
[13]
GVDD
GND
D2_
MA
[14]
D2_
MECC
[7]
D2_
MECC
[5]
D2_
MDQS
[3]
GVDD
GND
D2_
MDQ
[14]
D2_
MDM
[1]
D2_
MDQ
[13]
E
D2_
MODT
[3]
D2_
MWE
D2_
MCS
[0]
D2_
MA
[0]
D2_
MA
[8]
D2_
MBA
[2]
D2_
MECC
[6]
D2_
MDM
[8]
D2_
MCK
[0]
D2_
MCK
[0]
D2_
MDQ
[15]
GVDD
GND
D2_
MDQ
[12]
F
D2_
MAPAR_
OUT
GVDD
GND
D2_
MBA
[1]
GVDD
GND
D2_
MECC
[3]
GVDD
GND
D2_
MECC
[4]
D2_
MDQ
[11]
D2_
MDQS
[1]
D2_
MDQ
[9]
D2_
MDQ
[8]
G
D2_
MAPAR_
ERR
D2_
MCS
[3]
D2_
MA
[6]
D2_
MRAS
D2_
MA
[9]
D2_
MA
[3]
D2_
MCKE
[0]
D2_
MECC
[2]
D2_
MDQS
[8]
D2_
MECC
[0]
D2_
MDQ
[10]
D2_
MDQS
[1]
D2_
MDQ
[22]
D2_
MDM
[2]
H
GND
GVDD
D2_
MODT
[2]
D2_
MA
[5]
GVDD
GND
D2_
MCS
[2]
D2_
MECC
[1]
D2_
MDQS
[8]
GVDD
GND
D2_
MDQ
[23]
GVDD
GND
J
D2_
MVREF
D2_
MDIC
[0]
GVDD
D2_
MCAS
D2_
MBA
[0]
D2_
MA
[10]
D2_
MA
[2]
D2_
MA
[7]
D2_
MA
[12]
D2_
MCK
[1]
D2_
MCK
[1]
D2_
MDQ
[19]
D2_
MDQS
[2]
D2_
MDQ
[17]
K
AVDD_
QE
GND
GVDD
GVDD
GND
GVDD
GND
D2_
MCKE
[1]
GVDD
GVDD
GVDD
GND
D2_
MDQ
[18]
D2_
MDQS
[2]
L
AVDD_
CORE
D2_
MDIC
[1]
QE_PC
[3]
QE_PA
[22]
QE_PA
[18]
QE_PA
[15]
QE_PC
[16]
GND
GND
QE_PB
[18]
QE_PB
[12]
GND
VDD
GND
M
GND
GND
LVDD2
QE_PA
[23]
QE_PA
[20]
QE_PA
[16]
LVDD2
QE_PC
[17]
QE_PB
[19]
LVDD2
QE_PB
[13]
VDD
GND
VDD
N
QE_PA
[24]
QE_PA
[28]
QE_PC
[2]
QE_PA
[26]
QE_PA
[21]
QE_PA
[17]
GND
QE_PC
[24]
QE_PB
[20]
GND
QE_PB
[14]
GND
VDD
GND
P
QE_PA
[19]
QE_PB
[17]
QE_PC
[25]
QE_PB
[9]
QE_PB
[1]
QE_PA
[29]
QE_PA
[14]
QE_PB
[24]
QE_PB
[21]
QE_PB
[16]
QE_PB
[15]
VDD
GND
SENSEVDD
DETAIL A
Figure 3. MPC8569E Detail A Ball Map
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
5
Ball Layout Diagrams
The following figure provides detailed view B of the MPC8569E 783-pin BGA ball map diagram.
15
16
17
18
19
20
21
22
23
24
25
26
27
28
D1_
MA
[13]
D1_
MCKE
[3]
D1_
MDIC
[1]
D1_
MA
[1]
D1_
MA
[11]
D1_
MDIC
[0]
D1_
MDQ
[31]
D1_
MDQ
[30]
D1_
MDM
[3]
D1_
MDQ
[29]
D1_
MDQ
[7]
D1_
MDQ
[6]
D1_
MDM
[0]
D1_
MDQ
[5]
A
D2_
MDQ
[4]
GVDD
GND
D1_
MA
[4]
GVDD
GND
D1_
MDQ
[27]
GVDD
GND
D1_
MDQ
[28]
D1_
MDQ
[3]
GVDD
GND
D1_
MDQ
[4]
B
D1_
MA
[15]
D1_
MODT
[0]
D1_
MCKE
[2]
D1_
MA
[6]
D1_
MCK
[2]
D1_
MCK
[2]
D1_
MDQ
[26]
D1_
MDQ
[25]
D1_
MDQS
[3]
D1_
MDQ
[24]
D1_
MDQ
[2]
D1_
MDQS
[0]
D1_
MDQ
[1]
D1_
MDQ
[0]
C
GVDD
GND
D1_
MCS
[0]
GVDD
GND
D1_
MA
[14]
D1_
MECC
[7]
D1_
MECC
[5]
D1_
MDQS
[3]
GVDD
GND
D1_
MDQS
[0]
GVDD
GND
D
D1_
MAPAR_
OUT
D1_
MODT
[3]
D1_
MWE
D1_
MA
[0]
D1_
MA
[8]
D1_
MBA
[2]
D1_
MECC
[6]
D1_
MDM
[8]
D1_
MCK
[0]
D1_
MCK
[0]
D1_
MDQ
[15]
D1_
MDQ
[14]
D1_
MDM
[1]
D1_
MDQ
[13]
E
D1_
MAPAR_
ERR
GVDD
GND
D1_
MBA
[1]
GVDD
GND
D1_
MECC
[3]
GVDD
GND
D1_
MECC
[4]
D1_
MDQ
[11]
GVDD
GND
D1_
MDQ
[12]
F
D2_
MDQ
[21]
D1_
MCS
[3]
D1_
MODT
[2]
D1_
MRAS
D1_
MA
[9]
D1_
MA
[3]
D1_
MCKE
[0]
D1_
MECC
[2]
D1_
MDQS
[8]
D1_
MECC
[0]
D1_
MDQ
[10]
D1_
MDQS
[1]
D1_
MDQ
[9]
D1_
MDQ
[8]
G
D2_
MDQ
[20]
GVDD
GND
D1_
MA
[5]
D1_
MA
[2]
GVDD
GND
D1_
MECC
[1]
D1_
MDQS
[8]
GVDD
GND
D1_
MDQS
[1]
GVDD
GND
H
D2_
MDQ
[16]
D1_
MODT
[1]
D1_
MCAS
D1_
MA
[10]
GVDD
D1_
MCKE
[1]
D1_
MA
[7]
D1_
MA
[12]
D1_
MCK
[1]
D1_
MCK
[1]
D1_
MDQ
[23]
D1_
MDQ
[22]
D1_
MDM
[2]
D1_
MDQ
[21]
J
GND
D1_
MCS
[1]
D1_
MBA
[0]
GVDD
GND
D1_
MCS
[2]
GND
GVDD
D1_
MDQ
[18]
D1_
MDQS
[2]
D1_
MDQ
[19]
GVDD
GND
D1_
MDQ
[20]
K
GVDD
GND
VDD
GND
VDD
GND
GVDD
GND
GVDD
GND
D1_
MDQS
[2]
D1_
MDQ
[17]
D1_
MDQ
[16]
GND
L
GND
VDD
GND
VDD
GND
IRQ_
OUT
UDE
MCP
ASLEEP
CLK_
OUT
RTC
OVDD
GND
AVDD_
DDR
M
VDD
GND
VDD
GND
VDD
IRQ4_
MSRCID
[3]
TCK
TMS
OVDD
GND
TRIG_IN
BVDD_
VSEL
[0]
D1_
MVREF
AVDD_
PLAT
N
SENSEVSS
VDD
GND
VDD
GND
BVDD_
VSEL
[1]
TDI
TRST
TDO
TRIG_OUT_
_READY__ SYSCLK
QUIESCE
LVDD_
VSEL
[1]
GND
GND
P
DETAIL B
Figure 4. MPC8569E Detail B Ball Map
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
6
Freescale Semiconductor
Ball Layout Diagrams
The following figure provides detailed view C of the MPC8569E 783-pin BGA ball map diagram.
DETAIL C
R
QE_PA
[25]
QE_PB
[23]
QE_PC
[9]
LVDD1
QE_PB
[0]
LVDD1
QE_PC
[11]
QE_PA
[12]
QE_PA
[6]
QE_PA
[4]
QE_PA
[2]
GND
VDD
GND
T
QE_PA
[27]
QE_PB
[22]
QE_PB
[3]
GND
QE_PA
[31]
GND
QE_PC
[8]
QE_PA
[8]
GND
LVDD1
QE_PA
[0]
VDD
GND
VDD
U
QE_PE
[22]
QE_PB
[25]
QE_PB
[4]
QE_PB
[5]
QE_PB
[6]
QE_PA
[30]
QE_PC
[20]
QE_PA
[9]
QE_PA
[7]
QE_PA
[3]
QE_PA
[1]
GND
VDD
GND
V
QE_PE
[14]
QE_PE
[17]
QE_PB
[7]
QE_PB
[8]
QE_PB
[10]
QE_PB
[2]
QE_PC
[29]
QE_PA
[13]
QE_PA
[11]
QE_PA
[10]
QE_PA
[5]
VDD
GND
VDD
W
QE_PE
[16]
QE_PC
[5]
QE_PC
[0]
QE_PC
[1]
QE_PC
[6]
OVDD
QE_PC
[7]
QE_PC
[26]
QE_PC
[27]
OVDD
QE_PB
[11]
GND
VDD
GND
Y
QE_PE
[11]
OVDD
QE_PC
[22]
QE_PC
[23]
QE_PC
[19]
GND
QE_PC
[4]
QE_PD
[18]
QE_PD
[26]
GND
QE_PD
[21]
VDD
GND
VDD
AA
QE_PE
[10]
GND
QE_PC
[13]
QE_PC
[15]
QE_PC
[14]
QE_PC
[12]
QE_PD
[24]
QE_PD
[19]
QE_PD
[17]
QE_PD
[27]
QE_PD
[22]
QE_PD
[20]
QE_PC
[31]
QE_PC
[30]
AB
QE_PC
[21]
QE_PC
[10]
QE_PC
[18]
QE_PE
[15]
QE_PD
[10]
QE_PD
[6]
QE_PD
[15]
QE_PD
[16]
OVDD
QE_PD
[25]
QE_PD
[23]
QE_PE
[25]
QE_PE
[26]
LDP
[0]
AC
QE_PE
[12]
QE_PE
[13]
QE_PE
[18]
QE_PD
[11]
OVDD
QE_PD
[8]
QE_PD
[14]
QE_PB
[28]
GND
QE_PF
[10]
QE_PF
[11]
QE_PE
[24]
QE_PF
[4]
LCS
[3]
AD
QE_PE
[21]
QE_PE
[19]
QE_PE
[20]
QE_PD
[5]
GND
QE_PD
[9]
QE_PD
[7]
QE_PB
[29]
QE_PB
[30]
QE_PB
[31]
QE_PF
[12]
QE_PF
[9]
QE_PF
[5]
LCS4_
IRQ
[8]
AE
QE_PE
[23]
OVDD
QE_PE
[5]
QE_PD
[4]
QE_PD
[12]
QE_PD
[13]
QE_PE
[31]
QE_PF
[2]
QE_PF
[16]
QE_PF
[15]
OVDD
QE_PF
[7]
QE_PF
[3]
LA
[18]
AF
QE_PD
[28]
GND
QE_PE
[4]
QE_PE
[2]
QE_PD
[3]
QE_PD
[1]
OVDD
QE_PF
[0]
QE_PF
[17]
QE_PF
[18]
GND
QE_PF
[6]
QE_PC
[28]
LAD
[1]
AG
QE_PD
[29]
QE_PD
[30]
QE_PE
[6]
QE_PE
[3]
QE_PE
[9]
QE_PD
[2]
GND
QE_PF
[1]
QE_PF
[21]
QE_PE
[28]
QE_PE
[30]
QE_PF
[8]
QE_PB
[26]
LAD
[0]
AH
QE_PD
[31]
QE_PE
[0]
QE_PE
[1]
QE_PE
[8]
QE_PE
[7]
QE_PD
[0]
QE_PF
[20]
QE_PF
[19]
QE_PF
[22]
QE_PE
[29]
QE_PE
[27]
QE_PF
[13]
QE_PF
[14]
QE_PB
[27]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Figure 5. MPC8569E Detail C Ball Map
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
7
Ball Layout Diagrams
The following figure provides detailed view D of the MPC8569E 783-pin BGA ball map diagram.
DETAIL D
VDD
GND
VDD
GND
VDD
IRQ
[0]
IRQ5_
MSRCID
[4]
IRQ6_
DVAL
XVDD
XGND
IRQ
[3]
IRQ
[2]
SCOREVDD
SCOREGND
R
GND
VDD
GND
VDD
GND
GND
IRQ
[1]
Rsvd
SD_TX
[0]
SD_TX
[0]
SCOREVDD
SCOREGND
SD_RX
[0]
SD_RX
[0]
T
VDD
GND
VDD
GND
VDD
Rsvd
Rsvd
GND
XVDD
XGND
AGND_
SRDS
AVDD_
SRDS
SCOREGND
SCOREVDD
U
GND
VDD
GND
VDD
GND
GND
XVDD
XGND
SD_TX
[1]
SD_TX
[1]
SCOREGND
SCOREVDD
SD_RX
[1]
SD_RX
[1]
V
VDD
GND
VDD
GND
VDD
GND
XGND
XVDD
SD_REF_ SD_REF_ SCOREVDD
CLK
CLK
SCOREGND
W
GND
GND
GND
VDD
GND
LDP
[1]
LGPL
[5]
GND
LCS
[2]
BVDD
LCS
[1]
BVDD
LCS
[0]
LA
[16]
LA
[17]
LA
[19]
LBCTL
LA
[20]
BVDD
XGND
XVDD
SD_TX
[2]
SD_TX
[2]
SCOREVDD
SD_RX
[2]
SD_RX
[2]
Y
LGPL3_
LFWP
SD_TX_
CLK
SD_TX_
CLK
XVDD
XGND
SD_IMP_ SD_PLL_ SCORECAL_TX
TPA
GND
SCOREVDD
AA
LWE0_
LBS0_
LFWE
XVDD
XGND
SD_TX
[3]
SD_TX
[3]
XGND
SD_RX
[3]
SD_RX
[3]
AB
BVDD
LA
[25]
BVDD
LCS7_
IRQ
[11]
XGND
XVDD
SRESET
HRESET_ SCOREVDD
REQ
SCOREGND
AC
LA
[21]
LA
[23]
LGPL2_
LOE_
LFRE
LAD
[15]
LCS6_
IRQ
[10]
HRESET
DMA_
DACK2_
SD_CMD
LVDD_
VSEL
[0]
AD
LA
[22]
LA
[24]
LA
[26]
LAD
[13]
LAD
[12]
LA
[27]
LCS5_
IRQ
[9]
CKSTP_
IN
AE
LCLK
[1]
BVDD
LCLK
[0]
BVDD
LAD
[7]
BVDD
LAD
[14]
DMA_
DACK_
[0]
GND
LAD
[2]
GND
LAD
[6]
GND
LAD
[8]
GND
LAD
[11]
DMA_
DREQ_
[0]
LSYNC_
OUT
LSYNC_
IN
LAD
[3]
LAD
[4]
LAD
[5]
LALE
LAD
[9]
LAD
[10]
GND
15
16
17
18
19
20
21
22
23
LGPL4_
LGPL1_ LUPWAIT_ LGPL0_
LFALE LBPBSE_ LFCLE
LFRB
LWE1_
GND
GND
LBS
[1]
GND
SD_PLL_ SD_IMP_
TPD
CAL_RX
SCOREGND
SCOREGND
DMA_
DMA_
DMA_
DDONE_ DREQ2_ DACK1_
SD_DAT0 MSRCID1
[0]
DMA_
DMA_
DDONE1_ DREQ1_
MSRCID2 MSRCID0
GND
OVDD
UART_
DMA_
IIC2_ SIN0_DMA
DDONE2_ SCL_SD_ _DACK3_ CKSTP_
OUT
SD_WP
CD
SD_DAT2
UART_
UART_
IIC2_
IIC1_ CTS0_DMA SOUT0_DMA
GND SDA_SD_
SCL _DDONE3_ _DREQ3_
CLK
SD_DAT3 SD_DAT1
UART_
LSSD_
AVDD_
IIC1_
GND
RTS
LBIU
SDA
MODE
[0]
OVDD
24
25
26
27
AF
AG
AH
28
Figure 6. MPC8569E Detail D Ball Map
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
8
Freescale Semiconductor
Pinout List
1.2
Pinout List
The following table provides the pinout listing for the MPC8569E 783 FC-PBGA package.
Table 1. MPC8569E Pinout Listing
Signal1
Package Pin Number
Pin Type
Power Supply
Note
Clocks
RTC
M25
I
OVDD
—
SYSCLK
P25
I
OVDD
—
DDR SDRAM Memory Interface
D1_MA0
E18
O
GVDD
—
D1_MA1
A18
O
GVDD
—
D1_MA2
H19
O
GVDD
—
D1_MA3
G20
O
GVDD
—
D1_MA4
B18
O
GVDD
—
D1_MA5
H18
O
GVDD
—
D1_MA6
C18
O
GVDD
—
D1_MA7
J21
O
GVDD
—
D1_MA8
E19
O
GVDD
—
D1_MA9
G19
O
GVDD
—
D1_MA10
J18
O
GVDD
—
D1_MA11
A19
O
GVDD
—
D1_MA12
J22
O
GVDD
—
D1_MA13
A15
O
GVDD
—
D1_MA14
D20
O
GVDD
—
D1_MA15
C15
O
GVDD
—
D1_MBA0
K17
O
GVDD
—
D1_MBA1
F18
O
GVDD
—
D1_MBA2
E20
O
GVDD
—
D1_MCAS
J17
O
GVDD
—
D1_MCK0
E24
O
GVDD
—
D1_MCK0
E23
O
GVDD
—
D1_MCK1
J24
O
GVDD
—
D1_MCK1
J23
O
GVDD
—
D1_MCK2
C20
O
GVDD
—
D1_MCK2
C19
O
GVDD
—
D1_MCKE0
G21
O
GVDD
—
D1_MCKE1
J20
O
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
9
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
D1_MCKE2
C17
O
GVDD
—
D1_MCKE3
A16
O
GVDD
—
D1_MCS0
D17
O
GVDD
—
D1_MCS1
K16
O
GVDD
—
D1_MCS2
K20
O
GVDD
—
D1_MCS3
G16
O
GVDD
—
D1_MDIC0
A20
I/O
GVDD
27
D1_MDIC1
A17
I/O
GVDD
27
D1_MDM0
A27
I/O
GVDD
—
D1_MDM1
E27
I/O
GVDD
—
D1_MDM2
J27
I/O
GVDD
—
D1_MDM3
A23
I/O
GVDD
—
D1_MDM8
E22
I/O
GVDD
—
D1_MDQ0
C28
I/O
GVDD
—
D1_MDQ1
C27
I/O
GVDD
—
D1_MDQ2
C25
I/O
GVDD
—
D1_MDQ3
B25
I/O
GVDD
—
D1_MDQ4
B28
I/O
GVDD
—
D1_MDQ5
A28
I/O
GVDD
—
D1_MDQ6
A26
I/O
GVDD
—
D1_MDQ7
A25
I/O
GVDD
—
D1_MDQ8
G28
I/O
GVDD
—
D1_MDQ9
G27
I/O
GVDD
—
D1_MDQ10
G25
I/O
GVDD
—
D1_MDQ11
F25
I/O
GVDD
—
D1_MDQ12
F28
I/O
GVDD
—
D1_MDQ13
E28
I/O
GVDD
—
D1_MDQ14
E26
I/O
GVDD
—
D1_MDQ15
E25
I/O
GVDD
—
D1_MDQ16
L27
I/O
GVDD
—
D1_MDQ17
L26
I/O
GVDD
—
D1_MDQ18
K23
I/O
GVDD
—
D1_MDQ19
K25
I/O
GVDD
—
D1_MDQ20
K28
I/O
GVDD
—
D1_MDQ21
J28
I/O
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
10
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
D1_MDQ22
J26
I/O
GVDD
—
D1_MDQ23
J25
I/O
GVDD
—
D1_MDQ24
C24
I/O
GVDD
—
D1_MDQ25
C22
I/O
GVDD
—
D1_MDQ26
C21
I/O
GVDD
—
D1_MDQ27
B21
I/O
GVDD
—
D1_MDQ28
B24
I/O
GVDD
—
D1_MDQ29
A24
I/O
GVDD
—
D1_MDQ30
A22
I/O
GVDD
—
D1_MDQ31
A21
I/O
GVDD
—
D1_MDQS0
D26
I/O
GVDD
—
D1_MDQS0
C26
I/O
GVDD
—
D1_MDQS1
H26
I/O
GVDD
—
D1_MDQS1
G26
I/O
GVDD
—
D1_MDQS2
K24
I/O
GVDD
—
D1_MDQS2
L25
I/O
GVDD
—
D1_MDQS3
D23
I/O
GVDD
—
D1_MDQS3
C23
I/O
GVDD
—
D1_MDQS8
H23
I/O
GVDD
—
D1_MDQS8
G23
I/O
GVDD
—
D1_MECC0
G24
I/O
GVDD
—
D1_MECC1
H22
I/O
GVDD
—
D1_MECC2
G22
I/O
GVDD
—
D1_MECC3
F21
I/O
GVDD
—
D1_MECC4
F24
I/O
GVDD
—
D1_MECC5
D22
I/O
GVDD
—
D1_MECC6
E21
I/O
GVDD
—
D1_MECC7
D21
I/O
GVDD
—
D1_MODT0
C16
O
GVDD
—
D1_MODT1
J16
O
GVDD
—
D1_MODT2
G17
O
GVDD
—
D1_MODT3
E16
O
GVDD
—
D1_MAPAR_OUT
E15
O
GVDD
—
D1_MAPAR_ERR
F15
I
GVDD
—
D1_MRAS
G18
O
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
11
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
D1_MWE
E17
O
GVDD
—
D2_MA0
E4
O
GVDD
—
D2_MA1
A4
O
GVDD
—
D2_MA2
J7
O
GVDD
—
D2_MA3
G6
O
GVDD
—
D2_MA4
B4
O
GVDD
—
D2_MA5
H4
O
GVDD
—
D2_MA6
G3
O
GVDD
—
D2_MA7
J8
O
GVDD
—
D2_MA8
E5
O
GVDD
—
D2_MA9
G5
O
GVDD
—
D2_MA10
J6
O
GVDD
—
D2_MA11
A5
O
GVDD
—
D2_MA12
J9
O
GVDD
—
D2_MA13
D3
O
GVDD
—
D2_MA14
D6
O
GVDD
—
D2_MA15
B1
O
GVDD
—
D2_MBA0
J5
O
GVDD
—
D2_MBA1
F4
O
GVDD
—
D2_MBA2
E6
O
GVDD
—
D2_MCAS
J4
O
GVDD
—
D2_MCK0
E10
O
GVDD
—
D2_MCK0
E9
O
GVDD
—
D2_MCK1
J11
O
GVDD
—
D2_MCK1
J10
O
GVDD
—
D2_MCK2
C6
O
GVDD
—
D2_MCK2
C5
O
GVDD
—
D2_MCKE0
G7
O
GVDD
—
D2_MCKE1
K8
O
GVDD
—
D2_MCKE2
C2
O
GVDD
—
D2_MCKE3
A2
O
GVDD
—
D2_MCS0
E3
O
GVDD
—
D2_MCS1
A6
O
GVDD
—
D2_MCS2
H7
O
GVDD
—
D2_MCS3
G2
O
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
12
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
D2_MDIC0
J2
I/O
GVDD
27
D2_MDIC1
L2
I/O
GVDD
27
D2_MDM0/D1_MDM4
A13
I/O
GVDD
—
D2_MDM1/D1_MDM5
D13
I/O
GVDD
—
D2_MDM2/D1_MDM6
G14
I/O
GVDD
—
D2_MDM3/D1_MDM7
A9
I/O
GVDD
—
D2_MDM8
E8
I/O
GVDD
—
D2_MDQ0/D1_MDQ32
B14
I/O
GVDD
—
D2_MDQ1/D1_MDQ33
C14
I/O
GVDD
—
D2_MDQ2/D1_MDQ34
C11
I/O
GVDD
—
D2_MDQ3/D1_MDQ35
B11
I/O
GVDD
—
D2_MDQ4/D1_MDQ36
B15
I/O
GVDD
—
D2_MDQ5/D1_MDQ37
A14
I/O
GVDD
—
D2_MDQ6/D1_MDQ38
A12
I/O
GVDD
—
D2_MDQ7/D1_MDQ39
A11
I/O
GVDD
—
D2_MDQ8/D1_MDQ40
F14
I/O
GVDD
—
D2_MDQ9/D1_MDQ41
F13
I/O
GVDD
—
D2_MDQ10/D1_MDQ42
G11
I/O
GVDD
—
D2_MDQ11/D1_MDQ43
F11
I/O
GVDD
—
D2_MDQ12/D1_MDQ44
E14
I/O
GVDD
—
D2_MDQ13/D1_MDQ45
D14
I/O
GVDD
—
D2_MDQ14/D1_MDQ46
D12
I/O
GVDD
—
D2_MDQ15/D1_MDQ47
E11
I/O
GVDD
—
D2_MDQ16/D1_MDQ48
J15
I/O
GVDD
—
D2_MDQ17/D1_MDQ49
J14
I/O
GVDD
—
D2_MDQ18/D1_MDQ50
K13
I/O
GVDD
—
D2_MDQ19/D1_MDQ51
J12
I/O
GVDD
—
D2_MDQ20/D1_MDQ52
H15
I/O
GVDD
—
D2_MDQ21/D1_MDQ53
G15
I/O
GVDD
—
D2_MDQ22/D1_MDQ54
G13
I/O
GVDD
—
D2_MDQ23/D1_MDQ55
H12
I/O
GVDD
—
D2_MDQ24/D1_MDQ56
C10
I/O
GVDD
—
D2_MDQ25/D1_MDQ57
C8
I/O
GVDD
—
D2_MDQ26/D1_MDQ58
C7
I/O
GVDD
—
D2_MDQ27/D1_MDQ59
B7
I/O
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
13
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
D2_MDQ28/D1_MDQ60
B10
I/O
GVDD
—
D2_MDQ29/D1_MDQ61
A10
I/O
GVDD
—
D2_MDQ30/D1_MDQ62
A8
I/O
GVDD
—
D2_MDQ31/D1_MDQ63
A7
I/O
GVDD
—
D2_MDQS0/D1_MDQS4
C12
I/O
GVDD
—
D2_MDQS0/D1_MDQS4
C13
I/O
GVDD
—
D2_MDQS1/D1_MDQS5
G12
I/O
GVDD
—
D2_MDQS1/D1_MDQS5
F12
I/O
GVDD
—
D2_MDQS2/D1_MDQS6
J13
I/O
GVDD
—
D2_MDQS2/D1_MDQS6
K14
I/O
GVDD
—
D2_MDQS3/D1_MDQS7
D9
I/O
GVDD
—
D2_MDQS3/D1_MDQS7
C9
I/O
GVDD
—
D2_MDQS8
H9
I/O
GVDD
—
D2_MDQS8
G9
I/O
GVDD
—
D2_MECC0
G10
I/O
GVDD
—
D2_MECC1
H8
I/O
GVDD
—
D2_MECC2
G8
I/O
GVDD
—
D2_MECC3
F7
I/O
GVDD
—
D2_MECC4
F10
I/O
GVDD
—
D2_MECC5
D8
I/O
GVDD
—
D2_MECC6
E7
I/O
GVDD
—
D2_MECC7
D7
I/O
GVDD
—
D2_MODT0
C1
O
GVDD
—
D2_MODT1
A3
O
GVDD
—
D2_MODT2
H3
O
GVDD
—
D2_MODT3
E1
O
GVDD
—
D2_MAPAR_OUT
F1
O
GVDD
—
D2_MAPAR_ERR
G1
I
GVDD
—
D2_MRAS
G4
O
GVDD
—
D2_MWE
E2
O
GVDD
—
DMA
DMA_DACK0
AF23
O
OVDD
2
DMA_DACK1/MSRCID1
AD27
O
OVDD
11
DMA_DACK2/SD_CMD
AD24
O
OVDD
—
DMA_DDONE0
AD25
O
OVDD
2
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
14
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
DMA_DDONE1/MSRCID2
AE24
O
OVDD
2
DMA_DDONE2/SD_WP
AF25
O
OVDD
—
DMA_DREQ0
AG23
I
OVDD
—
DMA_DREQ1/MSRCID0
AE25
I
OVDD
—
DMA_DREQ2/SD_DAT0
AD26
I
OVDD
—
DUART
UART_SOUT0/DMA_DREQ3/SD_DAT1
AG28
O
OVDD
2
UART_SIN0/DMA_DACK3/SD_DAT2
AF27
I
OVDD
—
UART_CTS0/DMA_DDONE3/SD_DAT3
AG27
I
OVDD
—
UART_RTS0
AH28
O
OVDD
—
Enhanced Local Bus Controller Interface
LA16
AD15
O
BVDD
2
LA17
AD16
O
BVDD
2
LA18
AE14
O
BVDD
2
LA19
AD17
O
BVDD
2
LA20
AE16
O
BVDD
2
LA21
AD18
O
BVDD
2
LA22
AE17
O
BVDD
11
LA23
AD19
O
BVDD
2
LA24
AE18
O
BVDD
18
LA25
AC20
O
BVDD
18
LA26
AE19
O
BVDD
18
LA27
AE22
O
BVDD
18
LAD0
AG14
I/O
BVDD
23
LAD1
AF14
I/O
BVDD
23
LAD2
AG16
I/O
BVDD
23
LAD3
AH17
I/O
BVDD
23
LAD4
AH18
I/O
BVDD
23
LAD5
AH19
I/O
BVDD
23
LAD6
AG18
I/O
BVDD
23
LAD7
AF20
I/O
BVDD
23
LAD8
AG20
I/O
BVDD
23
LAD9
AH21
I/O
BVDD
23
LAD10
AH22
I/O
BVDD
23
LAD11
AG22
I/O
BVDD
23
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
15
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
LAD12
AE21
I/O
BVDD
23
LAD13
AE20
I/O
BVDD
23
LAD14
AF22
I/O
BVDD
23
LAD15
AD21
I/O
BVDD
23
LALE
AH20
O
BVDD
20
LBCTL
AE15
O
BVDD
20
LCLK0
AF18
O
BVDD
11
LCLK1
AF16
O
BVDD
11
LCS0
AC18
O
BVDD
2
LCS1
AC16
O
BVDD
2
LCS2
AB16
O
BVDD
2
LCS3
AC14
O
BVDD
21
LCS4/IRQ8
AD14
I/O
BVDD
21
LCS5/IRQ9
AE23
I/O
BVDD
21
LCS6/IRQ10
AD22
I/O
BVDD
21
LCS7/IRQ11
AC22
I/O
BVDD
21
LDP0
AB14
I/O
BVDD
—
LDP1
AA15
I/O
BVDD
—
LGPL0/LFCLE
AA19
O
BVDD
2
LGPL1/LFALE
AA17
O
BVDD
2
LGPL2/LOE/LFRE
AD20
O
BVDD
20
LGPL3/LFWP
AA20
O
BVDD
2
LGPL4/LUPWAIT/LBPBSE/LFRB
AA18
I/O
BVDD
29
LGPL5
AA16
O
BVDD
2
LSYNC_IN
AH16
I
BVDD
—
LSYNC_OUT
AH15
O
BVDD
—
LWE0/LBS0LFWE
AB20
O
BVDD
11
LWE1/LBS1
AB18
O
BVDD
24
2C
I
IIC1_SDA
AH26
I/O
OVDD
5, 28
IIC1_SCL
AG26
I/O
OVDD
5, 28
IIC2_SDA/SD_CLK
AG25
I/O
OVDD
3
IIC2_SCL/SD_CD
AF26
I/O
OVDD
3
I
OVDD
—
JTAG
TCK
N21
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
16
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
TDI
P21
I
OVDD
26
TDO
P23
O
OVDD
25
TMS
N22
I
OVDD
26
TRST
P22
I
OVDD
26
Programmable Interrupt Controller
IRQ0
R20
I
OVDD
—
IRQ1
T21
I
OVDD
—
IRQ2
R26
I
OVDD
—
IRQ3
R25
I
OVDD
—
IRQ4/MSRCID3
N20
I
OVDD
—
IRQ5/MSRCID4
R21
I
OVDD
—
IRQ6/MDVAL
R22
I
OVDD
—
IRQ_OUT
M20
O
OVDD
5, 6, 11
MCP
M22
I
OVDD
6
UDE
M21
I
OVDD
6
QUICC Engine Block
QE_PA0
T11
I/O
LVDD1
—
QE_PA1
U11
I/O
LVDD1
—
QE_PA2
R11
I/O
LVDD1
—
QE_PA3
U10
I/O
LVDD1
—
QE_PA4
R10
I/O
LVDD1
—
QE_PA5
V11
I/O
OVDD
—
QE_PA6
R9
I/O
LVDD1
—
QE_PA7
U9
I/O
LVDD1
—
QE_PA8
T8
I/O
LVDD1
—
QE_PA9
U8
I/O
LVDD1
—
QE_PA10
V10
I/O
OVDD
—
QE_PA11
V9
I/O
OVDD
—
QE_PA12
R8
I/O
LVDD1
—
QE_PA13
V8
I/O
OVDD
—
QE_PA14
P7
I/O
LVDD2
—
QE_PA15
L6
I/O
LVDD2
—
QE_PA16
M6
I/O
LVDD2
—
QE_PA17
N6
I/O
LVDD2
—
QE_PA18
L5
I/O
LVDD2
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
17
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
QE_PA19
P1
I/O
OVDD
—
QE_PA20
M5
I/O
LVDD2
—
QE_PA21
N5
I/O
LVDD2
—
QE_PA22
L4
I/O
LVDD2
—
QE_PA23
M4
I/O
LVDD2
—
QE_PA24
N1
I/O
OVDD
—
QE_PA25
R1
I/O
OVDD
—
QE_PA26
N4
I/O
LVDD2
—
QE_PA27
T1
I/O
OVDD
—
QE_PA28
N2
I/O
OVDD
—
QE_PA29
P6
I/O
LVDD1
—
QE_PA30
U6
I/O
LVDD1
—
QE_PA31
T5
I/O
LVDD1
—
QE_PB0
R5
I/O
LVDD1
—
QE_PB1
P5
I/O
LVDD1
—
QE_PB2
V6
I/O
OVDD
—
QE_PB3
T3
I/O
LVDD1
—
QE_PB4
U3
I/O
LVDD1
—
QE_PB5
U4
I/O
LVDD1
—
QE_PB6
U5
I/O
LVDD1
—
QE_PB7
V3
I/O
OVDD
11
QE_PB8
V4
I/O
OVDD
—
QE_PB9
P4
I/O
LVDD1
—
QE_PB10
V5
I/O
OVDD
—
QE_PB11
W11
I/O
OVDD
—
QE_PB12
L11
I/O
LVDD2
—
QE_PB13
M11
I/O
LVDD2
—
QE_PB14
N11
I/O
LVDD2
—
QE_PB15
P11
I/O
LVDD2
—
QE_PB16
P10
I/O
LVDD2
—
QE_PB17
P2
I/O
OVDD
—
QE_PB18
L10
I/O
LVDD2
—
QE_PB19
M9
I/O
LVDD2
—
QE_PB20
N9
I/O
LVDD2
—
QE_PB21
P9
I/O
LVDD2
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
18
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
QE_PB22
T2
I/O
OVDD
—
QE_PB23
R2
I/O
OVDD
—
QE_PB24
P8
I/O
LVDD2
—
QE_PB25
U2
I/O
OVDD
—
QE_PB26
AG13
I/O
OVDD
11
QE_PB27
AH14
I/O
OVDD
22
QE_PB28
AC8
I/O
OVDD
22
QE_PB29
AD8
I/O
OVDD
—
QE_PB30
AD9
I/O
OVDD
—
QE_PB31
AD10
I/O
OVDD
11
QE_PC0
W3
I/O
OVDD
—
QE_PC1
W4
I/O
OVDD
—
QE_PC2
N3
I/O
LVDD2
—
QE_PC3
L3
I/O
LVDD2
—
QE_PC4
Y7
I/O
OVDD
22
QE_PC5
W2
I/O
OVDD
—
QE_PC6
W5
I/O
OVDD
—
QE_PC7
W7
I/O
OVDD
—
QE_PC8
T7
I/O
LVDD1
—
QE_PC9
R3
I/O
LVDD1
—
QE_PC10
AB2
I/O
OVDD
—
QE_PC11
R7
I/O
LVDD1
—
QE_PC12
AA6
I/O
OVDD
—
QE_PC13
AA3
I/O
OVDD
—
QE_PC14
AA5
I/O
OVDD
—
QE_PC15
AA4
I/O
OVDD
—
QE_PC16
L7
I/O
LVDD2
—
QE_PC17
M8
I/O
LVDD2
—
QE_PC18
AB3
I/O
OVDD
—
QE_PC19
Y5
I/O
OVDD
—
QE_PC20
U7
I/O
LVDD1
—
QE_PC21
AB1
I/O
OVDD
—
QE_PC22
Y3
I/O
OVDD
—
QE_PC23
Y4
I/O
OVDD
—
QE_PC24
N8
I/O
LVDD2
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
19
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
QE_PC25
P3
I/O
LVDD1
—
QE_PC26
W8
I/O
OVDD
—
QE_PC27
W9
I/O
OVDD
—
QE_PC28
AF13
I/O
OVDD
—
QE_PC29
V7
I/O
OVDD
—
QE_PC30
AA14
I/O
OVDD
—
QE_PC31
AA13
I/O
OVDD
—
QE_PD0
AH6
I/O
OVDD
11
QE_PD1
AF6
I/O
OVDD
—
QE_PD2
AG6
I/O
OVDD
—
QE_PD3
AF5
I/O
OVDD
—
QE_PD4
AE4
I/O
OVDD
22
QE_PD5
AD4
I/O
OVDD
—
QE_PD6
AB6
I/O
OVDD
—
QE_PD7
AD7
I/O
OVDD
—
QE_PD8
AC6
I/O
OVDD
—
QE_PD9
AD6
I/O
OVDD
—
QE_PD10
AB5
I/O
OVDD
—
QE_PD11
AC4
I/O
OVDD
—
QE_PD12
AE5
I/O
OVDD
—
QE_PD13
AE6
I/O
OVDD
—
QE_PD14
AC7
I/O
OVDD
—
QE_PD15
AB7
I/O
OVDD
—
QE_PD16
AB8
I/O
OVDD
—
QE_PD17
AA9
I/O
OVDD
—
QE_PD18
Y8
I/O
OVDD
—
QE_PD19
AA8
I/O
OVDD
—
QE_PD20
AA12
I/O
OVDD
—
QE_PD21
Y11
I/O
OVDD
—
QE_PD22
AA11
I/O
OVDD
—
QE_PD23
AB11
I/O
OVDD
—
QE_PD24
AA7
I/O
OVDD
—
QE_PD25
AB10
I/O
OVDD
—
QE_PD26
Y9
I/O
OVDD
—
QE_PD27
AA10
I/O
OVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
20
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
QE_PD28
AF1
I/O
OVDD
—
QE_PD29
AG1
I/O
OVDD
—
QE_PD30
AG2
I/O
OVDD
—
QE_PD31
AH1
I/O
OVDD
—
QE_PE0
AH2
I/O
OVDD
—
QE_PE1
AH3
I/O
OVDD
—
QE_PE2
AF4
I/O
OVDD
—
QE_PE3
AG4
I/O
OVDD
—
QE_PE4
AF3
I/O
OVDD
—
QE_PE5
AE3
I/O
OVDD
—
QE_PE6
AG3
I/O
OVDD
—
QE_PE7
AH5
I/O
OVDD
—
QE_PE8
AH4
I/O
OVDD
—
QE_PE9
AG5
I/O
OVDD
—
QE_PE10
AA1
I/O
OVDD
—
QE_PE11
Y1
I/O
OVDD
—
QE_PE12
AC1
I/O
OVDD
—
QE_PE13
AC2
I/O
OVDD
—
QE_PE14
V1
I/O
OVDD
—
QE_PE15
AB4
I/O
OVDD
—
QE_PE16
W1
I/O
OVDD
—
QE_PE17
V2
I/O
OVDD
—
QE_PE18
AC3
I/O
OVDD
—
QE_PE19
AD2
I/O
OVDD
—
QE_PE20
AD3
I/O
OVDD
—
QE_PE21
AD1
I/O
OVDD
—
QE_PE22
U1
I/O
OVDD
—
QE_PE23
AE1
I/O
OVDD
—
QE_PE24
AC12
I/O
OVDD
11
QE_PE25
AB12
I/O
OVDD
2
QE_PE26
AB13
I/O
OVDD
11
QE_PE27
AH11
I/O
OVDD
19
QE_PE28
AG10
I/O
OVDD
19
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
21
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
QE_PE29
AH10
I/O
OVDD
19
QE_PE30
AG11
I/O
OVDD
—
QE_PE31
AE7
I/O
OVDD
—
QE_PF0
AF8
I/O
OVDD
—
QE_PF1
AG8
I/O
OVDD
—
QE_PF2
AE8
I/O
OVDD
—
QE_PF3
AE13
I/O
OVDD
—
QE_PF4
AC13
I/O
OVDD
—
QE_PF5
AD13
I/O
OVDD
—
QE_PF6
AF12
I/O
OVDD
—
QE_PF7
AE12
I/O
OVDD
—
QE_PF8
AG12
I/O
OVDD
—
QE_PF9
AD12
I/O
OVDD
2
QE_PF10
AC10
I/O
OVDD
2
QE_PF11
AC11
I/O
OVDD
2
QE_PF12
AD11
I/O
OVDD
—
QE_PF13
AH12
I/O
OVDD
11
QE_PF14
AH13
I/O
OVDD
2
QE_PF15
AE10
I/O
OVDD
—
QE_PF16
AE9
I/O
OVDD
—
QE_PF17
AF9
I/O
OVDD
—
QE_PF18
AF10
I/O
OVDD
—
QE_PF19
AH8
I/O
OVDD
—
QE_PF20
AH7
I/O
OVDD
—
QE_PF21
AG9
I/O
OVDD
—
QE_PF22
AH9
I/O
OVDD
—
SerDes
SD_IMP_CAL_RX
W22
I
—
7
SD_IMP_CAL_TX
AA25
I
—
17
SD_PLL_TPA
AA26
O
AVDD_SRDS
8
SD_PLL_TPD
W21
O
XVDD
8
SD_REF_CLK
W26
I
ScoreVDD
—
SD_REF_CLK
W25
I
ScoreVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
22
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
SD_RX0
T28
I
ScoreVDD
30
SD_RX0
T27
I
ScoreVDD
30
SD_RX1
V28
I
ScoreVDD
30
SD_RX1
V27
I
ScoreVDD
30
SD_RX2
Y28
I
ScoreVDD
30
SD_RX2
Y27
I
ScoreVDD
30
SD_RX3
AB28
I
ScoreVDD
30
SD_RX3
AB27
I
ScoreVDD
30
SD_TX0
T23
O
XVDD
31
SD_TX0
T24
O
XVDD
31
SD_TX1
V23
O
XVDD
31
SD_TX1
V24
O
XVDD
31
SD_TX2
Y23
O
XVDD
31
SD_TX2
Y24
O
XVDD
31
SD_TX3
AB23
O
XVDD
31
SD_TX3
AB24
O
XVDD
31
SD_TX_CLK
AA21
O
XVDD
8
SD_TX_CLK
AA22
O
XVDD
8
System Control
CKSTP_IN
AE28
I
OVDD
4
CKSTP_OUT
AF28
O
OVDD
5, 6, 11
HRESET
AD23
I
OVDD
4
HRESET_REQ
AC26
O
OVDD
11
SRESET
AC25
I
OVDD
4
Debug
TRIG_OUT/READY/QUIESCE
P24
O
OVDD
11
CLK_OUT
M24
O
OVDD
—
TRIG_IN
N25
I
OVDD
—
Voltage Control
LVDD_VSEL0
AD28
I
OVDD
15
LVDD_VSEL1
P26
I
OVDD
16
BVDD_VSEL0
N26
I
OVDD
14
BVDD_VSEL1
P20
I
OVDD
14
I
OVDD
10
Design for Test
LSSD_MODE
AH27
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
23
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
O
OVDD
11
Power Management
ASLEEP
M23
Thermal Management
THERM0
U21
—
Internal
temperature
diode cathode
32
THERM1
U20
—
Internal
temperature
diode anode
32
Reserved
T22
—
—
9
Reference voltage for
DDR
MVREF
—
Analog
D1_MVREF
N27
D2_MVREF
J1
—
Power and Ground
VDD
L13
1.0-V/1.1-V core
power supply
VDD
—
VDD
L17
1.0-V/1.1-V core
power supply
VDD
—
VDD
L19
1.0-V/1.1-V core
power supply
VDD
—
VDD
M12
1.0-V/1.1-V core
power supply
VDD
—
VDD
M14
1.0-V/1.1-V core
power supply
VDD
—
VDD
M16
1.0-V/1.1-V core
power supply
VDD
—
VDD
M18
1.0-V/1.1-V core
power supply
VDD
—
VDD
N13
1.0-V/1.1-V core
power supply
VDD
—
VDD
N15
1.0-V/1.1-V core
power supply
VDD
—
VDD
N17
1.0-V/1.1-V core
power supply
VDD
—
VDD
N19
1.0-V/1.1-V core
power supply
VDD
—
VDD
P12
1.0-V/1.1-V core
power supply
VDD
—
VDD
P16
1.0-V/1.1-V core
power supply
VDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
24
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
VDD
P18
1.0-V/1.1-V core
power supply
VDD
—
VDD
R13
1.0-V/1.1-V core
power supply
VDD
—
VDD
R15
1.0-V/1.1-V core
power supply
VDD
—
VDD
R17
1.0-V/1.1-V core
power supply
VDD
—
VDD
R19
1.0-V/1.1-V core
power supply
VDD
—
VDD
T12
1.0-V/1.1-V core
power supply
VDD
—
VDD
T14
1.0-V/1.1-V core
power supply
VDD
—
VDD
T16
1.0-V/1.1-V core
power supply
VDD
—
VDD
T18
1.0-V/1.1-V core
power supply
VDD
—
VDD
U13
1.0-V/1.1-V core
power supply
VDD
—
VDD
U15
1.0-V/1.1-V core
power supply
VDD
—
VDD
U17
1.0-V/1.1-V core
power supply
VDD
—
VDD
U19
1.0-V/1.1-V core
power supply
VDD
—
VDD
V12
1.0-V/1.1-V core
power supply
VDD
—
VDD
V14
1.0-V/1.1-V core
power supply
VDD
—
VDD
V16
1.0-V/1.1-V core
power supply
VDD
—
VDD
V18
1.0-V/1.1-V core
power supply
VDD
—
VDD
W13
1.0-V/1.1-V core
power supply
VDD
—
VDD
W15
1.0-V/1.1-V core
power supply
VDD
—
VDD
W17
1.0-V/1.1-V core
power supply
VDD
—
VDD
W19
1.0-V/1.1-V core
power supply
VDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
25
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
VDD
Y12
1.0-V/1.1-V core
power supply
VDD
—
VDD
Y14
1.0-V/1.1-V core
power supply
VDD
—
VDD
Y18
1.0-V/1.1-V core
power supply
VDD
—
BVDD
AC15
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
BVDD
AC17
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
BVDD
AC19
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
BVDD
AC21
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
BVDD
AF15
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
BVDD
AF17
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
BVDD
AF19
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
BVDD
AF21
3.3-/2.5-/1.8-V
enhanced local bus
controller (eLBC)
power supply
BVDD
—
GVDD
B12
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
B16
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
B19
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
B2
1.8-/1.5-V DDR power
supply
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
26
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
GVDD
B22
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
B26
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
B5
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
B8
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
C3
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
D1
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
D10
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
D15
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
D18
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
D24
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
D27
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
D4
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
E12
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
F16
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
F19
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
F2
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
F22
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
F26
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
F5
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
F8
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
H10
1.8-/1.5-V DDR power
supply
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
27
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
GVDD
H13
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
H16
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
H2
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
H20
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
H24
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
H27
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
H5
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
J19
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
J3
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K10
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K11
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K18
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K22
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K26
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K3
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K4
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K6
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
K9
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
L15
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
L21
1.8-/1.5-V DDR power
supply
GVDD
—
GVDD
L23
1.8-/1.5-V DDR power
supply
GVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
28
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
LVDD1
R4
3.3-/2.5-V Ethernet
power supply
LVDD1
—
LVDD1
R6
3.3-/2.5-V Ethernet
power supply
LVDD1
—
LVDD1
T10
3.3-/2.5-V Ethernet
power supply
LVDD1
—
LVDD2
M10
3.3-/2.5-V Ethernet
power supply
LVDD2
—
LVDD2
M3
3.3-/2.5-V Ethernet
power supply
LVDD2
—
LVDD2
M7
3.3-/2.5-V Ethernet
power supply
LVDD2
—
OVDD
AB9
3.3-V power supply
OVDD
—
OVDD
AC5
3.3-V power supply
OVDD
—
OVDD
AE11
3.3-V power supply
OVDD
—
OVDD
AE2
3.3-V power supply
OVDD
—
OVDD
AE27
3.3-V power supply
OVDD
—
OVDD
AF24
3.3-V power supply
OVDD
—
OVDD
AF7
3.3-V power supply
OVDD
—
OVDD
M26
3.3-V power supply
OVDD
—
OVDD
N23
3.3-V power supply
OVDD
—
OVDD
W10
3.3-V power supply
OVDD
—
OVDD
W6
3.3-V power supply
OVDD
—
OVDD
Y2
3.3-V power supply
OVDD
—
ScoreVDD
AA28
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
ScoreVDD
AC27
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
ScoreVDD
R27
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
ScoreVDD
T25
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
ScoreVDD
U28
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
ScoreVDD
V26
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
ScoreVDD
W27
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
ScoreVDD
Y25
1.0-V/1.1-V SerDes
power supply
ScoreVDD
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
29
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
SENSEVDD
P14
Core supply sense
VDD
13
XVDD
AA23
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
XVDD
AB21
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
XVDD
AC24
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
XVDD
R23
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
XVDD
U23
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
XVDD
V21
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
XVDD
W24
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
XVDD
Y22
1.0-V/1.1-V SerDes
I/O power supply
XVDD
—
AVDD_CORE
L1
1.0-V/1.1-V AVDD
supply for the core
PLL
—
12
AVDD_DDR
M28
1.0-V/1.1-V AVDD
supply for the DDR
PLL
—
12
AVDD_LBIU
AH24
1.0-V/1.1-V AVDD
supply for the eLBC
PLL
—
12
AVDD_PLAT
N28
1.0-V/1.1-V AVDD
supply for the platform
PLL
—
12
AVDD_QE
K1
1.0-V/1.1-V AVDD
supply for the QUICC
Engine block PLL
—
12
AVDD_SRDS
U26
1.0-V/1.1-V AVDD
supply for the SerDes
PLL
—
12
GND
AA2
—
—
—
GND
AB15
—
—
—
GND
AB17
—
—
—
GND
AB19
—
—
—
GND
AC9
—
—
—
GND
AD5
—
—
—
GND
AE26
—
—
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
30
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
GND
AF11
—
—
—
GND
AF2
—
—
—
GND
AG15
—
—
—
GND
AG17
—
—
—
GND
AG19
—
—
—
GND
AG21
—
—
—
GND
AG24
—
—
—
GND
AG7
—
—
—
GND
AH23
—
—
—
GND
AH25
—
—
—
GND
B13
—
—
—
GND
B17
—
—
—
GND
B20
—
—
—
GND
B23
—
—
—
GND
B27
—
—
—
GND
B3
—
—
—
GND
B6
—
—
—
GND
B9
—
—
—
GND
C4
—
—
—
GND
D11
—
—
—
GND
D16
—
—
—
GND
D19
—
—
—
GND
D2
—
—
—
GND
D25
—
—
—
GND
D28
—
—
—
GND
D5
—
—
—
GND
E13
—
—
—
GND
F17
—
—
—
GND
F20
—
—
—
GND
F23
—
—
—
GND
F27
—
—
—
GND
F3
—
—
—
GND
F6
—
—
—
GND
F9
—
—
—
GND
H1
—
—
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
31
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
GND
H11
—
—
—
GND
H14
—
—
—
GND
H17
—
—
—
GND
H21
—
—
—
GND
H25
—
—
—
GND
H28
—
—
—
GND
H6
—
—
—
GND
K12
—
—
—
GND
K15
—
—
—
GND
K19
—
—
—
GND
K2
—
—
—
GND
K21
—
—
—
GND
K27
—
—
—
GND
K5
—
—
—
GND
K7
—
—
—
GND
L12
—
—
—
GND
L14
—
—
—
GND
L16
—
—
—
GND
L18
—
—
—
GND
L20
—
—
—
GND
L22
—
—
—
GND
L24
—
—
—
GND
L28
—
—
—
GND
L8
—
—
—
GND
L9
—
—
—
GND
M1
—
—
—
GND
M13
—
—
—
GND
M15
—
—
—
GND
M17
—
—
—
GND
M19
—
—
—
GND
M2
—
—
—
GND
M27
—
—
—
GND
N10
—
—
—
GND
N12
—
—
—
GND
N14
—
—
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
32
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
GND
N16
—
—
—
GND
N18
—
—
—
GND
N24
—
—
—
GND
N7
—
—
—
GND
P13
—
—
—
GND
P17
—
—
—
GND
P19
—
—
—
GND
P27
—
—
—
GND
P28
—
—
—
GND
R12
—
—
—
GND
R14
—
—
—
GND
R16
—
—
—
GND
R18
—
—
—
GND
T13
—
—
—
GND
T15
—
—
—
GND
T17
—
—
—
GND
T19
—
—
—
GND
T4
—
—
—
GND
T6
—
—
—
GND
T9
—
—
—
GND
U12
—
—
—
GND
U14
—
—
—
GND
U16
—
—
—
GND
U18
—
—
—
GND
U22
—
—
—
GND
V13
—
—
—
GND
V15
—
—
—
GND
V17
—
—
—
GND
V19
—
—
—
GND
W12
—
—
—
GND
W14
—
—
—
GND
W16
—
—
—
GND
W18
—
—
—
GND
Y6
—
—
—
GND
Y10
—
—
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
33
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
GND
Y13
—
—
—
GND
Y15
—
—
—
GND
Y16
—
—
—
GND
Y17
—
—
—
GND
Y19
—
—
—
GND
V20
—
—
—
GND
T20
—
—
—
GND
W20
—
—
—
GND
Y20
—
—
—
SENSEVSS
P15
Ground sense
—
13
SCOREGND
AA27
SerDes Core Logic
GND
—
—
SCOREGND
AB26
SerDes Core Logic
GND
—
—
SCOREGND
AC28
SerDes Core Logic
GND
—
—
SCOREGND
R28
SerDes Core Logic
GND
—
—
SCOREGND
T26
SerDes Core Logic
GND
—
—
SCOREGND
U27
SerDes Core Logic
GND
—
—
SCOREGND
V25
SerDes Core Logic
GND
—
—
SCOREGND
W28
SerDes Core Logic
GND
—
—
SCOREGND
Y26
SerDes Core Logic
GND
—
—
XGND
AA24
SerDes Transceiver
Pad GND
—
—
XGND
AB22
SerDes Transceiver
Pad GND
—
—
XGND
AB25
SerDes Transceiver
Pad GND
—
—
XGND
AC23
SerDes Transceiver
Pad GND
—
—
XGND
R24
SerDes Transceiver
Pad GND
—
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
34
Freescale Semiconductor
Pinout List
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
XGND
U24
SerDes Transceiver
Pad GND
—
—
XGND
V22
SerDes Transceiver
Pad GND
—
—
XGND
W23
SerDes Transceiver
Pad GND
—
—
XGND
Y21
SerDes Transceiver
Pad GND
—
—
AGND_SRDS
U25
SerDes PLL GND
—
—
Notes:
1. All multiplexed signals are listed only once and do not reoccur.
2. This pin is a reset configuration pin. It has a weak internal pull-up P-FET which is enabled only when the processor is in the
reset state. This pull-up is designed such that it can be overpowered by an external 4.7-kΩ pull-down resistor. However, if the
signal is intended to be high after reset, and if there is any device on the net which might pull down the value of the net at
reset, then a pull-up or active driver is needed.
3. When configured as I2C, this pin is an open drain signal and recommend a pull-up resistor (1 kΩ) be placed on this pin to
OVDD. When configured as SD, this pin is not open drain and does not require a pull-up.
4. This pin has a weak internal pull-up resistor (~20 kΩ).
5. This pin is an open drain signal.
6. Recommend a weak pull-up resistor (2–10 kΩ) be placed on this pin to OVDD.
7. This pin requires a 200-Ω pull-down to ground.
8. Do not connect.
9. Recommend a weak pull-down resistor (2–10 kΩ) be placed on this pin to GND.
10. These are test signals for factory use only and must be pulled up (100 Ω–1 kΩ) to OVDD for normal machine operation.
11. These pins must not be pulled down during power-on reset.
12. See AN4232 MPC8569E PowerQUICC III Design Checklist for the required PLL filters to be attached to the AVDD pin.
13. These pins are connected to the VDD/GND planes internally and may be used by the core power supply to improve tracking
and regulation.
14. This pin selects the voltage of eLBC interface (BVDD). This pin has internal weak pull down.
15. This pin selects the voltage of UCC1 and UCC3 interfaces (LVDD1). This pin has internal weak pull down.
16. This pin selects the voltage of UCC2 and UCC4 interfaces (LVDD2). This pin has internal weak pull down.
17. This pin requires a 100-Ω pull down to ground.
18. The value of LA[24:27] during reset sets the CCB clock to SYSCLK PLL ratio. These pins require 4.7-kΩ pull-up or pull-down
resistors. See AN4232 MPC8569E PowerQUICC III Design Checklist for more details.
19. The value of QE_PE[27:29] during reset sets the DDR clock PLL settings. These pins require 4.7-kΩ pull up or pull down
resistors. See AN4232 MPC8569E PowerQUICC III Design Checklist for more details.
20. The value of LALE, LGPL2/LOE/LFRE and LBCTL at reset set the e500 core clock to CCB Clock PLL ratio. These pins
require 4.7-kΩ pull-up or pull-down resistors. See the AN4232 MPC8569E PowerQUICC III Design Checklist for more details.
21. The value of LCS[3:7] at reset sets the QE PLL settings. These pins require 4.7-kΩ pull up or pull down resistors. See
AN4232 MPC8569E PowerQUICC III Design Checklist for more details.
22. The value of QE_PB[27:28], QE_PC4 and QE_PD4 at reset sets the Boot ROM location. These pins require 4.7-kΩ pull up
or pull down resistors. See the MPC8569E PowerQUICC III Integrated Host Processor Family Reference Manual for details
23. These pins are sampled at reset for general-purpose configuration use by software. The value of LAD[0:15] at reset sets the
upper 16 bits of the GPPORCR
24. These pins must not be pulled up during power-on reset.
25. This output is actively driven during reset rather than being three-stated during reset.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
35
Overall DC Electrical Characteristics
Table 1. MPC8569E Pinout Listing (continued)
Signal1
Package Pin Number
Pin Type
Power Supply
Note
26. These JTAG pins have weak internal pull-up P-FETs that are always enabled.
27. When operating in DDR2 mode, connect Dn_MDIC[0] to ground through an 18.2-Ω (full-strength mode) or 36.4-Ω
(half-strength mode) precision 1% resistor and connect Dn_MDIC[1] to GVDD through an 18.2-Ω (full-strength mode) or
36.4-Ω (half-strength mode) precision 1% resistor. When operating in DDR3 mode, connect Dn_MDIC[0] to ground through
a 20-Ω (full-strength mode) or 40.2-Ω (half-strength mode) precision 1% resistor and connect Dn_MDIC[1] to GVDD through
a 20-Ω (full-strength mode) or 40.2-Ω (half-strength mode) precision 1% resistor. These pins are used for automatic
calibration of the DDR IOs.
28. Recommend a pull-up resistor (1 kΩ) to be placed on this pin to OVDD.
29. For systems which boot from local bus (GPCM)-controlled NOR flash or (FCM)-controlled NAND flash, a pull up on LGPL4
is required.
30. If unused, these pins must be connected to GND.
31. If unused, these pins must be left unconnected.
32. These pins may be connected to a temperature diode monitoring device such as the On Semiconductor, NCT1008™. If a
temperature diode monitoring device is not connected, these pins may be connected to test point or left as a no connect.
2
Electrical Characteristics
This section provides the AC and DC electrical specifications for the MPC8569E. This device is currently targeted to these
specifications, some of which are independent of the I/O cell, but are included for a more complete reference. These are not
purely I/O buffer design specifications.
2.1
Overall DC Electrical Characteristics
This section covers the DC ratings, conditions, and other characteristics.
2.1.1
Absolute Maximum Ratings
The following table provides the absolute maximum ratings.
Table 2. Absolute Maximum Ratings1
Characteristic
Symbol
Range
Unit
Notes
Core supply voltage
VDD
–0.3 to 1.21
V
—
PLL supply voltage
AVDD_CORE
AVDD_DDR,
AVDD_LBIU,
AVDD_PLAT,
AVDD_QE,
AVDD_SRDS
–0.3 to 1.21
V
—
Core power supply for SerDes transceiver
ScoreVDD
–0.3 to 1.21
V
—
Pad power supply for SerDes transceiver
XVDD
–0.3 to 1.21
V
—
DDR2 and DDR3 DRAM I/O voltage
GVDD
–0.3 to 1.98
–0.3 to 1.65
V
2
QUICC Engine block Ethernet interface I/O voltage
LVDD1
–0.3 to 3.63
–0.3 to 2.75
V
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
36
Freescale Semiconductor
Overall DC Electrical Characteristics
Table 2. Absolute Maximum Ratings1 (continued)
Characteristic
Symbol
Range
Unit
Notes
QUICC Engine block Ethernet interface I/O voltage
LVDD2
–0.3 to 3.63
–0.3 to 2.75
V
—
Debug, DMA, DUART, PIC, I2C, JTAG, power management,
QUICC Engine block, eSDHC, GPIO, clocking, SPI, I/O
voltage select and system control I/O voltage
OVDD
–0.3 to 3.63
V
—
Enhanced local bus I/O voltage
BVDD
–0.3 to 3.63
–0.3 to 2.75
–0.3 to 1.98
V
—
Input voltage
MVIN
–0.3 to (GVDD + 0.3)
V
2, 3
MVREF
–0.3 to (GVDD + 0.3)
V
—
LVIN
–0.3 to (LVDDn + 0.3)
V
3
BVIN
–0.3 to (BVDD + 0.3)
—
3
Debug, DMA, DUART, PIC, I
JTAG, power management,
QUICC Engine block, eSDHC,
GPIO, clocking, SPI, I/O voltage
select and system control I/O
voltage
OVIN
–0.3 to (OVDD + 0.3)
V
3
SerDes signals
XVIN
–0.3 to (XVDD + 0.3)
V
—
TSTG
–55 to 150
°C
—
DDR2/DDR3 DRAM signals
DDR2/DDR3 DRAM reference
Ethernet signals
Enhanced local bus signals
2C,
Storage junction temperature range
Notes:
1. Functional and tested operating conditions are given in Table 3. Absolute maximum ratings are stress ratings only, and
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
2. The –0.3 to 1.98 V range is for DDR2, and the –0.3 to 1.65 V range is for DDR3.
3. Caution: (B,M,L,O,X)VIN must not exceed (B,G,L,O,X)VDD by more than 0.3 V. This limit may be exceeded for a maximum of
20 ms during power-on reset and power-down sequences.
2.1.1.1
Recommended Operating Conditions
The following table provides the recommended operating conditions for this device. Proper device operation outside these
conditions is not guaranteed.
Table 3. Recommended Operating Conditions
Characteristic
Symbol
Recommended
Value
Unit
Notes
Core supply voltage
VDD
1.0 V ± 30 mV
1.1 V ± 33 mV
V
1
PLL supply voltage
AVDD_CORE,
AVDD_DDR,
AVDD_LBIU,
AVDD_PLAT,
AVDD_QE,
AVDD_SRDS
1.0 V ± 30 mV
1.1 V ± 33 mV
V
2
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
37
Overall DC Electrical Characteristics
Table 3. Recommended Operating Conditions (continued)
Characteristic
Symbol
Recommended
Value
Unit
Notes
Core power supply for SerDes transceiver
ScoreVDD
1.0 V ± 30 mV
1.1 V ± 33 mV
V
1
Pad power supply for SerDes transceiver
XVDD
1.0 V ± 30 mV
1.1 V ± 33 mV
V
1
DDR2 and DDR3 DRAM I/O voltage
GVDD
1.8 V ± 90 mV
1.5 V ± 75 mV
V
4
QUICC Engine block Ethernet interface I/O voltage
LVDD1
3.3 V ± 165 mV
2.5 V ± 125 mV
V
—
QUICC Engine block Ethernet interface I/O voltage
LVDD2
3.3 V ± 165 mV
2.5 V ± 125 mV
V
—
Debug, DMA, DUART, PIC, I2C, JTAG, power management, QUICC
Engine block, eSDHC, GPIO, clocking, SPI, I/O voltage select and
system control I/O voltage
OVDD
3.3 V ± 165 mV
V
—
Enhanced local bus I/O voltage
BVDD
3.3 V ± 165 mV
2.5 V ± 125 mV
1.8 V ± 90 mV
V
—
Input voltage
MVIN
GND to GVDD
V
3
DDR2 DRAM reference
MVREF
GVDD/2 ± 2%
V
3
DDR3 DRAM reference
MVREF
GVDD/2 ± 1%
V
3
LVIN
GND to LVDDn
V
3
BVIN
GND to BVDD
V
3
Debug, DMA, DUART, PIC,
JTAG, power
management, QUICC Engine, eSDHC, GPIO,
clocking, SPI, I/O voltage select and system
control I/O voltage
OVIN
GND to OVDD
V
3
SerDes signals
XVIN
GND to XVDD
V
—
TA = 0 (min) to
TJ = 105 (max)
oC
—
DDR2 and DDR3 DRAM signals
Ethernet signals
Enhanced local bus signals
I2C,
Operating
Temperature
range
Commercial
TA,
TJ
Notes:
1. A nominal voltage of 1.1 V is recommended for CPU speeds of 1.33 GHz and QUICC Engine block speeds of 667 MHz.
2. This voltage is the input to the filter and not the voltage at the AVDD pin, which may be reduced from VDD by the filter.
3. Caution: (B,M,L,O,X)VIN must not exceed (B,G,L,O,X)VDD by more than 0.3 V. This limit may be exceeded for a maximum of
20 ms during power-on reset and power-down sequences.
4. The 1.8 V ± 90 mV range is for DDR2, and the 1.5 V ± 75 mV range is for DDR3.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
38
Freescale Semiconductor
Overall DC Electrical Characteristics
The following figure shows the undershoot and overshoot voltages at the interfaces of the MPC8569E.
Nominal (B,G,L,O,X)VDD + 20%
(B,G,L,O,X)VDD + 5%
VIH
(B,G,L,O,X)VDD
GND
GND – 0.3 V
VIL
GND – 0.7 V
Not to Exceed 10%
of tCLOCK1
Note:
1. Note that tCLOCK refers to the clock period associated with the respective interface:
For I2C and JTAG, tCLOCK references SYSCLK.
For DDR, tCLOCK references Dn_MCK.
For eLBC, tCLOCK references LCLKn
.For eLBC, tCLOCK references LCLKn
For SerDEs XVDD, tCLOCK references SD_REF_CLK.
Figure 7. Overshoot/Undershoot Voltage for BVDD/GVDD/LVDD/OVDD/XVDD
The core voltage must always be provided at nominal 1.0 or 1.1 V. See Table 3 for actual recommended core voltage. Voltage
to the processor interface I/Os is provided through separate sets of supply pins and must be provided at the voltages shown in
Table 3. The input voltage threshold scales with respect to the associated I/O supply voltage. (B,M,L,O)VDD based receivers
are simple CMOS I/O circuits and satisfy appropriate LVCMOS type specifications. The DDR2 and DDR3 SDRAM interface
uses differential receivers referenced by the externally supplied Dn_MVREF signal (nominally set to GVDD/2) as is appropriate
for the SSTL_1.8 electrical signaling standard for DDR2 or 1.5-V electrical signaling for DDR3. The DDR DQS receivers
cannot be operated in single-ended fashion. The complement signal must be properly driven and cannot be grounded.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
39
Overall DC Electrical Characteristics
2.1.1.2
Output Driver Characteristics
The following table provides information on the characteristics of the output driver strengths. The values are preliminary
estimates.
Table 4. Output Drive Capability
Driver Type
Programmable Output Impedance (Ω)
Supply Voltage
Notes
45
45
45
BVDD = 3.3 V
BVDD = 2.5 V
BVDD = 1.8 V
—
DDR2 signal
18 (full strength mode)
35 (half strength mode)
GVDD = 1.8 V
1
DDR3 signal
20 (full strength mode)
40 (half strength mode)
GVDD = 1.5 V
1
45
OVDD = 3.3 V
—
Enhanced local bus interface utilities signals
DUART, EPIC, I2C, JTAG, system control
Note:
1. The drive strength of the DDR2 or DDR3 interface in half-strength mode is at TJ = 105°C and at GVDD (min). Refer to the
MPC8569 reference manual for the DDR impedance programming procedure through the DDR control driver register 1
(DDRCDR_1).
2.1.2
Power Sequencing
The MPC8569E requires its power rails to be applied in a specific sequence to ensure proper device operation. These
requirements are as follows for power up:
1.
2.
VDD, AVDD_n, BVDD, LVDDn, OVDD, ScoreVDD, XVDD
GVDD
All supplies must be at their stable values within 50 ms.
Items on the same line have no ordering requirement with respect to one another. Items on separate lines must be ordered
sequentially such that voltage rails on a previous step must reach 90% of their value before the voltage rails on the current step
reach 10% of theirs.
NOTE
While VDD is ramping, current may be supplied from VDD through the MPC8569E to
GVDD. Nevertheless, GVDD from an external supply should follow the sequencing
described above.
From a system standpoint, if any of the I/O power supplies ramp prior to the VDD core supply, the I/Os associated with that I/O
supply may drive a logic one or zero during power up, and extra current may be drawn by the device.
2.1.3
RESET Initialization
This section describes the AC electrical specifications for the RESET timing requirements of the MPC8569E. The following
table describes the specifications for the RESET initialization timing.
Table 5. RESET Initialization Timing Specifications
Parameter
Min
Max
Unit
Notes
Required assertion time of HRESET
10
—
SYSCLK
1, 2
Minimum assertion time of TRESET simultaneous to HRESET assertion
25
—
ns
3
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
40
Freescale Semiconductor
Overall DC Electrical Characteristics
Table 5. RESET Initialization Timing Specifications (continued)
Parameter
Min
Max
Unit
Notes
Maximum rise/fall time of HRESET
—
1
SYSCLK
5
Minimum assertion time for SRESET
3
—
SYSCLK
4
PLL input setup time with stable SYSCLK before HRESET negation
2
—
SYSCLK
—
Input setup time for POR configurations (other than PLL configuration)
with respect to negation of HRESET
4
—
SYSCLK
4
Input hold time for all POR configurations (including PLL configuration)
with respect to negation of HRESET
8
—
SYSCLK
4
Maximum valid-to-high impedance time for actively driven POR
configurations with respect to negation of HRESET
—
5
SYSCLK
4
Note:
1. There may be some extra current leakage when driving signals high during this time.
2. Reset assertion timing requirements for DDR3 DRAMs may differ.
3. TRST is an asynchronous level sensitive signal. For guidance on how this requirement can be met, refer to the JTAG signal
termination guidelines in AN4232 MPC8569E PowerQUICC III Design Checklist.
4. SYSCLK is the primary clock input for the MPC8569E.
5. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
The following table provides the PLL lock times.
Table 6. PLL Lock Times
Parameter
Min
Max
Unit
Core PLL lock time
—
100
μs
Platform PLL lock time
—
100
μs
QUICC Engine block PLL lock time
—
100
μs
DDR PLL lock times
—
100
μs
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
41
Power Characteristics
2.1.4
Power-on Ramp Rate
This section describes the AC electrical specifications for the power-on ramp rate requirements. Controlling the maximum
Power-On Ramp Rate is required to avoid falsely triggering the ESD circuitry. The following table provides the power supply
ramp rate specifications.
Table 7. Power Supply Ramp Rate
Parameter
Min
Max
Unit
Notes
Required ramp rate for all voltage supplies (including OVDD/CVDD/
GVDD/BVDD/SVDD/LVDD, All VDD supplies, MVREF and all AVDD supplies.)
—
36000
V/s
1, 2
Note:
1. Ramp rate is specified as a linear ramp from 10 to 90%. If non-linear (for example, exponential), the maximum rate of change
from 200 to 500 mV is the most critical as this range may falsely trigger the ESD circuitry.
2. Over full recommended operating temperature range (see Table 3).
2.2
Power Characteristics
The following table shows the power dissipations of the VDD supply for various operating core complex bus clock (CCB_clk)
frequencies versus the core, DDR data rate, and QUICC Engine block frequencies. Note that these numbers are based on design
estimates only and are preliminary. More accurate power numbers are available after the measurement on the silicon is
complete.
Table 8. MPC8569E Power Dissipation
Power Mode
Typical
DDR Data
Core
Platform
Rate
Frequency Frequency
Frequency
(MHz)
(MHz)
(MHz)
800
400
600
QUICC
Engine
Block
Frequency
(MHz)
VDD
Core
(V)
Junction
Temperature
(°C)
Power5
Notes
400
1.0
65
3.4 W
1, 2
105
4.9 W
1, 3
5.4 W
1, 4
65
3.9 W
1, 2
105
5.4 W
1, 3
6.0 W
1, 4
Thermal
Maximum
Typical
Thermal
Maximum
1067
533
667
533
1.0
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
42
Freescale Semiconductor
Input Clocks
Table 8. MPC8569E Power Dissipation (continued)
DDR Data
Core
Platform
Rate
Frequency Frequency
Frequency
(MHz)
(MHz)
(MHz)
Power Mode
Typical
1333
533
QUICC
Engine
Block
Frequency
(MHz)
VDD
Core
(V)
Junction
Temperature
(°C)
Power5
Notes
667
1.1
65
5.7 W
1, 2
105
7.9 W
1, 3
8.6 W
1, 4
800
Thermal
Maximum
Note:
1. These values do not include power dissipation for I/O supplies.
2. Typical power is an average value measured while running the Dhrystone benchmark, using the nominal process and
recommended core voltage (VDD) at 65 °C junction temperature (see Table 3).
3. Thermal power is the maximum power measured while running the Dhrystone benchmark, using the worst case process and
recommended core voltage (VDD) at maximum operating junction temperature (see Table 3).
4. Maximum power is the maximum power measured while running a test which includes an entirely L1-cache-resident,
contrived sequence of instructions that keeps the execution unit maximally busy and a typical workload on platform interfaces,
using the worst case process and nominal core voltage (VDD) at maximum operating junction temperature (see Table 3).
5. This table includes power numbers for the VDD, AVDD_n, and ScoreVDD rails.
2.3
Input Clocks
The following table provides the system clock (SYSCLK) DC specifications.
Table 9. SYSCLK DC Electrical Characteristics
At recommended operating conditions with OVDD = 3.3 V ± 165 mV
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Input high voltage
VIH
2.0
—
—
V
1
Input low voltage
VIL
—
—
0.8
V
1
Input capacitance
CIN
—
10.5
11.5
pf
—
Input current (VIN= 0 V or VIN = VDD)
IIN
—
—
±50
μA
2
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol VIN, in this case, represents the OVIN symbol referenced in Table 3.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
43
Input Clocks
The following table provides the system clock (SYSCLK) AC timing specifications.
Table 10. SYSCLK AC Timing Specifications
At recommended operating conditions with OVDD = 3.3 V ± 165 mV
Parameter/Condition
Symbol
Min
Typ
Max
Unit
Notes
SYSCLK frequency
fSYSCLK
66
—
133
MHz
1, 2
SYSCLK cycle time
tSYSCLK
7.5
—
15.15
ns
1, 2
SYSCLK duty cycle
tKHK/
tSYSCLK/DDRCLK
40
—
60
%
2
SYSCLK slew rate
—
1
—
4
V/ns
3
SYSCLK peak period jitter
—
—
—
± 150
ps
—
SYSCLK jitter phase noise at –56 dBc
—
—
—
500
KHz
4
AC Input Swing Limits at 3.3 V OVDD
ΔVAC
1.9
—
—
V
—
Notes:
1. Caution: The relevant clock ratio settings must be chosen such that the resulting SYSCLK frequency do not exceed their
respective maximum or minimum operating frequencies.
2. Measured at the rising edge and/or the falling edge at OVDD/2.
3. Slew rate as measured from ±0.3 ΔVAC at the center of peak to peak voltage at clock input.
4. Phase noise is calculated as FFT of TIE jitter.
2.3.1
Spread Spectrum Sources
Spread spectrum clock sources are an increasingly popular way to control electromagnetic interference emissions (EMI) by
spreading the emitted noise to a wider spectrum and reducing the peak noise magnitude in order to meet industry and
government requirements. These clock sources intentionally add long-term jitter to diffuse the EMI spectral content. The jitter
specification given in below table considers short-term (cycle-to-cycle) jitter only. The clock generator’s cycle-to-cycle output
jitter should meet the MPC8569E input cycle-to-cycle jitter requirement. Frequency modulation and spread are separate
concerns; the MPC8569E is compatible with spread spectrum sources if the recommendations listed in the following table are
observed.
Table 11. Spread Spectrum Clock Source Recommendations
At recommended operating conditions with OVDD = 3.3 V ± 165 mV.
Parameter
Min
Max
Unit
Notes
Frequency modulation
—
60
kHz
—
Frequency spread
—
1.0
%
1, 2
Notes:
1. SYSCLK frequencies that result from frequency spreading and the resulting core frequency must meet the minimum and
maximum specifications given in Table 10.
2. Maximum spread spectrum frequency may not result in exceeding any maximum operating frequency of the device.
CAUTION
The processor’s minimum and maximum SYSCLK and core frequencies must not be
exceeded regardless of the type of clock source. Therefore, systems in which the processor
is operated at its maximum rated e500 core frequency should avoid violating the stated
limits by using down-spreading only.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
44
Freescale Semiconductor
DDR2 and DDR3 SDRAM Controller
2.3.2
Real Time Clock Timing
The real time clock timing (RTC) input is sampled by the core complex bus clock (CCB_clk). The output of the sampling latch
is then used as an input to the counters of the PIC and the time base unit of the e500; there is no need for jitter specification.
The minimum pulse width of the RTC signal must be greater than 2x the period of the CCB_clk. That is, minimum clock high
time is 2 × tCCB_clk, and minimum clock low time is 2 × tCCB_clk. There is no minimum RTC frequency; RTC may be grounded
if not needed.
2.3.3
Gigabit Ethernet Reference Clock Timing
The following table provides the gigabit Ethernet reference clock (TX_CLK) AC timing specifications.
Table 12. TX_CLK3,4 AC Timing Specifications
At recommended operating conditions with LVDD = 2.5 V ± 125 mV / 3.3 V ± 165 mV.
Parameter/Condition
Symbol
Min
Typical
Max
Unit
Notes
TX_CLK frequency
tG125
—
125
—
MHz
—
TX_CLK cycle time
tG125
—
8
—
ns
—
tG125R/tG125F
—
—
ns
1, 5
%
2, 5
ps
2, 5
TX_CLK rise and fall time
LVDD = 2.5 V
LVDD = 3.3 V
TX_CLK duty cycle
0.75
1.0
—
tG125H/tG125
45
47
GMII, TBI
1000Base-T for RGMII, RTBI
TX_CLK jitter
—
—
55
53
—
± 150
Notes:
1. Rise and fall times for TX_CLK are measured from 0.5 and 2.0 V for LVDD = 2.5 V, and from 0.6 and 2.7 V for LVDD = 3.3 V.
2. TX_CLK is used to generate the GTX clock for the UEC transmitter with 2% degradation. The TX_CLK duty cycle can be
loosened from 47%/53% as long as the PHY device can tolerate the duty cycle generated by the UEC GTX_CLK. See
Section 2.6.3.7, “RGMII and RTBI AC Timing Specifications,” for duty cycle for 10Base-T and 100Base-T reference clock.
3. Gigabit transmit 125-MHz source. This signal must be generated externally with a crystal or oscillator, or is sometimes
provided by the PHY. TX_CLK is a 125-MHz input into the UCC Ethernet Controller and is used to generate all 125-MHz
related signals and clocks in the following modes: GMII, TBI, RTBI, RGMII.
4. For GMII and TBI modes, TX_CLK is provided to UCC1 through QE_PC[8:11,14,15] (CLK9-12,15,16) and to UCC2 through
QE_PC[2,3,6,7,15:17](CLK3,4,7,8,16:18). For RGMII and RTBI modes, TX_CLK is provided to UCC1 and UCC3 through
QE_PC11(CLK12) and to UCC2 and UCC4 through QE_PC16 (CLK17).
5. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing
2.3.4
Other Input Clocks
A description of the overall clocking of this device is available in the MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual in the form of a clock subsystem block diagram. For information about the input clock requirements
of other functional blocks such as SerDes, Ethernet Management, eSDHC, and Enhanced Local Bus see the specific interface
section.
2.4
DDR2 and DDR3 SDRAM Controller
This section describes the DC and AC electrical specifications for the DDR2 and DDR3 SDRAM controller interface of the
MPC8569E. Note that the required GVDD(typ) is 1.8 V for DDR2 SDRAM and GVDD(typ) is 1.5 V for DDR3 SDRAM.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
45
DDR2 and DDR3 SDRAM Controller
2.4.1
DDR2 and DDR3 SDRAM Interface DC Electrical Characteristics
The following table provides the recommended operating conditions for the DDR SDRAM controller when interfacing to
DDR2 SDRAM.
Table 13. DDR2 SDRAM Interface DC Electrical Characteristics
At recommended operating condition with GVDD = 1.8 V1
Parameter
Symbol
Min
Max
Unit
Notes
MVREFn
0.49 × GVDD
0.51 × GVDD
V
2, 3, 4
Input high voltage
VIH
MVREFn + 0.125
—
V
5
Input low voltage
VIL
—
MVREFn – 0.125
V
5
Output high current (VOUT = 1.320 V)
IOH
—
–13.4
mA
6, 7
Output low current (VOUT = 0.380 V)
IOL
13.4
—
mA
6, 7
I/O leakage current
IOZ
–50
50
μA
8
I/O reference voltage
Notes:
1. GVDD is expected to be within 50 mV of the DRAM’s voltage supply at all times. The DRAM’s and memory controller’s voltage
supply may or may not be from the same source.
2. MVREFn is expected to be equal to 0.5 × GVDD and to track GVDD DC variations as measured at the receiver. Peak-to-peak
noise on MVREFn may not exceed the MVREFn DC level by more than ±2% of GVDD (that is, ± 36 mV).
3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made, and it is expected to be
equal to MVREFn with a min value of MVREFn – 0.04 and a max value of MVREFn + 0.04. VTT should track variations in the
DC level of MVREFn.
4. The voltage regulator for MVREFn must meet the specifications stated in Table 16.
5. Input capacitance load for DQ, DQS, and DQS are available in the IBIS models.
6. IOH and IOL are measured at GVDD = 1.7 V.
7. Refer to the IBIS model for the complete output IV curve characteristics.
8. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD.
The following table provides the recommended operating conditions for the DDR SDRAM controller when interfacing to
DDR3 SDRAM.
Table 14. DDR3 SDRAM Interface DC Electrical Characteristics
At recommended operating condition with GVDD = 1.5 V1
Parameter
I/O reference voltage
Symbol
Min
Max
Unit
Note
MVREFn
0.49 × GVDD
0.51 × GVDD
V
2, 3, 4
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
46
Freescale Semiconductor
DDR2 and DDR3 SDRAM Controller
Table 14. DDR3 SDRAM Interface DC Electrical Characteristics (continued)
At recommended operating condition with GVDD = 1.5 V1
Parameter
Symbol
Min
Max
Unit
Note
Input high voltage
VIH
MVREFn + 0.100
GVDD
V
5
Input low voltage
VIL
GND
MVREFn – 0.100
V
5
I/O leakage current
IOZ
–50
50
μA
6
Notes:
1. GVDD is expected to be within 50 mV of the DRAM’s voltage supply at all times. The DRAM’s and memory controller’s voltage
supply may or may not be from the same source.
2. MVREFn is expected to be equal to 0.5 × GVDD and to track GVDD DC variations as measured at the receiver. Peak-to-peak
noise on MVREFn may not exceed the MVREFn DC level by more than ±1% of GVDD (that is, ± 15 mV).
3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made, and it is expected to be
equal to MVREFn with a min value of MVREFn – 0.04 and a max value of MVREFn + 0.04. VTT should track variations in the
DC level of MVREFn.
4. The voltage regulator for MVREFn must meet the specifications stated in Table 16.
5. Input capacitance load for DQ, DQS, and DQS are available in the IBIS models.
6. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD.
The following table provides the DDR controller interface capacitance for DDR2 and DDR3.
Table 15. DDR2 and DDR3 SDRAM Capacitance
At recommended operating conditions with GVDD of 1.8 V ± 5% for DDR2 or 1.5 V ± 5% for DDR3
Parameter
Symbol
Min
Max
Unit
Notes
Input/output capacitance: DQ, DQS, DQS
CIO
6
8
pF
1, 2
Delta input/output capacitance: DQ, DQS,
DQS
CDIO
—
0.5
pF
1, 2
Note:
1. This parameter is sampled. GVDD = 1.8 V ± 0.1 V (for DDR2), f = 1 MHz, TA = 25 °C, VOUT = GVDD/2, VOUT
(peak-to-peak) = 0.2 V.
2. This parameter is sampled. GVDD = 1.5 V ± 0.075 V (for DDR3), f = 1 MHz, TA = 25 °C, VOUT = GVDD/2, VOUT
(peak-to-peak) = 0.175 V.
The following table provides the current draw characteristics for MVREFn.
Table 16. Current Draw Characteristics for MVREFn
For recommended operating conditions, see Table 3.
Parameter
Symbol
Min
Max
Unit
Notes
Current draw for DDR2 SDRAM for MVREFn
IMVREFn
—
300
μA
—
Current draw for DDR3 SDRAM for MVREFn
IMVREFn
—
250
μA
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
47
DDR2 and DDR3 SDRAM Controller
2.4.2
DDR2 and DDR3 SDRAM Interface AC Timing Specifications
This section provides the AC timing specifications for the DDR SDRAM controller interface. The DDR controller supports both
DDR2 and DDR3 memories. Note that the required GVDD(typ) voltage is 1.8 V or 1.5 V when interfacing to DDR2 or DDR3
SDRAM respectively.
2.4.2.1
DDR2 and DDR3 SDRAM Interface Input AC Timing Specifications
The following table provides the input AC timing specifications for the DDR controller when interfacing to DDR2 SDRAM.
Table 17. DDR2 SDRAM Interface Input AC Timing Specifications
At recommended operating conditions with GVDD of 1.8 V ± 5%
Parameter
AC input low voltage
> 533 MHz data rate
Symbol
Min
Max
Unit
Notes
VILAC
—
MVREFn – 0.20
V
—
—
MVREFn – 0.25
MVREFn + 0.20
—
V
—
MVREFn + 0.25
—
≤ 533 MHz data rate
AC input high voltage
> 533 MHz data rate
VIHAC
≤ 533 MHz data rate
The following table provides the input AC timing specifications for the DDR controller when interfacing to DDR3 SDRAM.
Table 18. DDR3 SDRAM Interface Input AC Timing Specifications
At recommended operating conditions with GVDD of 1.5 V ± 5%
Parameter
Symbol
Min
Max
Unit
Notes
AC input low voltage
VILAC
—
MVREFn – 0.175
V
—
AC input high voltage
VIHAC
MVREFn + 0.175
—
V
—
The following table provides the input AC timing specifications for the DDR controller when interfacing to DDR2 and DDR3
SDRAM.
Table 19. DDR2 and DDR3 SDRAM Interface Input AC Timing Specifications3
At recommended operating conditions with GVDD of 1.8 V ± 5% for DDR2 or 1.5 V ± 5% for DDR3
Parameter
Symbol
Min
Max
Unit
Note
tCISKEW
—
—
ps
1
800 MHz data rate
–200
200
1
667 MHz data rate
–240
240
1
533 MHz data rate
–300
300
1
400 MHz data rate
–365
365
1
Controller Skew for MDQS—MDQ/MECC
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
48
Freescale Semiconductor
DDR2 and DDR3 SDRAM Controller
Table 19. DDR2 and DDR3 SDRAM Interface Input AC Timing Specifications3 (continued)
At recommended operating conditions with GVDD of 1.8 V ± 5% for DDR2 or 1.5 V ± 5% for DDR3
Parameter
Symbol
Min
Max
Unit
Note
tDISKEW
—
—
ps
2
800 MHz data rate
–425
425
2
667 MHz data rate
–510
510
2
533 MHz data rate
–635
635
2
400 MHz data rate
–885
885
2
Tolerated Skew for MDQS—MDQ/MECC
Note:
1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any corresponding bit that is
captured with MDQS[n]. This must be subtracted from the total timing budget.
2. The amount of skew that can be tolerated from MDQS to a corresponding MDQ signal is called tDISKEW.This can be
determined by the following equation: tDISKEW = ±(T ÷ 4 – abs(tCISKEW)) where T is the clock period and abs(tCISKEW) is the
absolute value of tCISKEW.
3. Parameters tested in DDR2 mode are to 400, 533, 667, and 800 MHz data rates and in DDR3 mode to 667 and 800 MHz data
rates.
The following figure shows the DDR2 and DDR3 SDRAM interface input timing diagram.
MCK[n]
MCK[n]
tMCK
MDQS[n]
tDISKEW
MDQ[x]
D0
D1
tDISKEW
tDISKEW
Figure 8. DDR2 and DDR3 SDRAM Interface Input Timing Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
49
DDR2 and DDR3 SDRAM Controller
2.4.2.2
DDR2 and DDR3 SDRAM Interface Output AC Timing Specifications
The following table contains the output AC timing targets for the DDR2 and DDR3 SDRAM interface.
Table 20. DDR2 and DDR3 SDRAM Interface Output AC Timing Specifications6
At recommended operating conditions with GVDD of 1.8 V ± 5% for DDR2 or 1.5 V ± 5% for DDR3.
Parameter
MCK[n] cycle time
ADDR/CMD output setup with respect to
MCK
Symbol1
Min
Max
Unit
Notes
tMCK
2.5
5
ns
2
ns
3
ns
3
ns
3
ns
3
ns
4
tDDKHAS
0.9177
0.888
1.10
1.48
1.95
800 MHz
667 MHz
533 MHz
400 MHz
ADDR/CMD output hold with respect to
MCK
667 MHz
533 MHz
400 MHz
—
0.917
1.10
1.48
1.95
—
—
—
—
—
—
—
tDDKHCX
800 MHz
667 MHz
533 MHz
400 MHz
MCK to MDQS skew
0.9177
0.888
1.10
1.48
1.95
tDDKHCS
800 MHz
667 MHz
533 MHz
400 MHz
MCS[n] output hold with respect to MCK
—
—
—
tDDKHAX
800 MHz
MCS[n] output setup with respect to MCK
—
0.917
1.10
1.48
1.95
—
—
—
—
–0.375
–0.6
0.375
0.6
tDDKHMH
800 MHz
≤ 667 MHz
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
50
Freescale Semiconductor
DDR2 and DDR3 SDRAM Controller
Table 20. DDR2 and DDR3 SDRAM Interface Output AC Timing Specifications6
At recommended operating conditions with GVDD of 1.8 V ± 5% for DDR2 or 1.5 V ± 5% for DDR3.
Symbol1
Parameter
MDQ/MECC/MDM output setup with
respect to MDQS
2807
3208
4007
4508
538
700
667 MHz
533 MHz
400 MHz
667 MHz
533 MHz
400 MHz
Max
tDDKHDS,
tDDKLDS
800 MHz
MDQ/MECC/MDM output hold with
respect to MDQS
800 MHz
Min
tDDKHDX,
tDDKLDX
2807
3208
4007
4508
538
700
Unit
Notes
ps
5
ps
5
—
—
—
—
—
—
—
—
Notes:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing
(DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example,
tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs
(A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference
(K) goes low (L) until data outputs (D) are invalid (X) or data output hold time.
2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.
3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MECC/MDM/MDQS.
4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD)
from the rising edge of the MCK[n] clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control
of the MDQS override bits (called WR_DATA_DELAY) in the TIMING_CFG_2 register. This will typically be set to the same
delay as in DDR_SDRAM_CLK_CNTL[CLK_ADJUST]. The timing parameters listed in the table assume that these 2
parameters have been set to the same adjustment value. See the MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual for a description and understanding of the timing modifications enabled by use of these bits.
5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC
(MECC), or data mask (MDM). The data strobe must be centered inside of the data eye at the pins of the microprocessor.
6. Parameters tested in DDR2 mode are to 400, 533, 667, and 800 MHz data rate and in DDR3 mode to 667 and 800 MHz data
rate.
7. DDR3 only
8. DDR2 only
NOTE
For the ADDR/CMD setup and hold specifications in Table 20, it is assumed that the clock
control register is set to adjust the memory clocks by ½ applied cycle.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
51
DDR2 and DDR3 SDRAM Controller
The following figure shows the DDR2 and DDR3 SDRAM interface output timing for the MCK to MDQS skew measurement
(tDDKHMH).
MCK[n]
MCK[n]
tMCK
tDDKHMHmax) = 0.6 ns or 0.375 ns
MDQS
tDDKHMH(min) = –0.6 ns or –0.375 ns
MDQS
Figure 9. Timing Diagram for tDDKHMH
The following figure shows the DDR2 and DDR3 SDRAM output timing diagram.
MCK
MCK
tMCK
tDDKHAS, tDDKHCS
tDDKHAX, tDDKHCX
ADDR/CMD
Write A0
NOOP
tDDKHMP
tDDKHMH
MDQS[n]
tDDKHME
tDDKHDS
tDDKLDS
MDQ[x]
D0
D1
tDDKLDX
tDDKHDX
Figure 10. DDR2 and DDR3 Output Timing Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
52
Freescale Semiconductor
DUART
The following figure provides the AC test load for the DDR2 and DDR3 controller bus.
Z0 = 50 Ω
Output
RL = 50 Ω
GVDD/2
Figure 11. DDR2 and DDR3 Controller Bus AC Test Load
2.5
DUART
This section describes the DC and AC electrical specifications for the DUART interface of the MPC8569E.
2.5.1
DUART DC Electrical Characteristics
The following table provides the DC electrical characteristics for the DUART interface.
Table 21. DUART DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = mn, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the min and max OVIN respective values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
2.5.2
DUART AC Electrical Specifications
The following table provides the AC timing parameters for the DUART interface.
Table 22. DUART AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Value
Unit
Notes
Minimum baud rate
fCCB/1,048,576
baud
1
Maximum baud rate
fCCB/16
baud
1, 2
16
—
3
Oversample rate
Notes:
1. fCCB refers to the internal platform clock.
2. The actual attainable baud rate is limited by the latency of interrupt processing.
3. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are
sampled each 16th sample.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
53
Ethernet Interface
2.6
Ethernet Interface
This section provides the AC and DC electrical characteristics for the Ethernet interfaces inside the QUICC Engine block.
2.6.1
GMII/SGMII/MII/SMII/RMII/TBI/RGMII/RTBI Electrical Characteristics
The electrical characteristics specified here apply to all gigabit media independent interface (GMII), serial gigabit media
independent interface (SGMII), media independent interface (MII), ten-bit interface (TBI), reduced gigabit media independent
interface (RGMII), reduced ten-bit interface (RTBI), and reduced media independent interface (RMII) signals except
management data input/output (MDIO) and management data clock (MDC). The RGMII and RTBI interfaces are defined for
2.5 V, while the GMII and TBI interfaces are defined for 3.3 V. The GMII, MII, and TBI interface timing is compatible with
IEEE Std 802.3™. The RGMII and RTBI interfaces follow the Reduced Gigabit Media-Independent Interface (RGMII)
Specification Version 1.3 (12/10/2000). The RMII interface follows the RMII Consortium RMII Specification Version 1.2
(3/20/1998). The electrical characteristics for the SGMII is specified in Section 2.6.4, “SGMII Interface Electrical
Characteristics.” The electrical characteristics for MDIO and MDC are specified in Section 2.7, “Ethernet Management
Interface.”
2.6.2
GMII, MII, RMII, SMII, TBI, RGMII and RTBI DC Electrical
Characteristics
The following table shows the GMII, MII, RMII, SMII, and TBI DC electrical characteristics when operating from a 3.3 V
supply.
Table 23. GMII, MII, RMII, SMII, and TBI DC Electrical Characteristics
At recommended operating conditions with LVDD = 3.3 V
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2.0
—
V
1
Input low voltage
VIL
—
0.90
V
—
Input high current (VIN = LVDD)
IIH
—
40
μA
2
Input low current (VIN = GND)
IIL
–600
—
μA
2
Output high voltage (LVDD = min, IOH = –4.0 mA)
VOH
2.1
LVDD + 0.3
V
—
Output low voltage (LVDD = min, IOL = 4.0 mA)
VOL
GND
0.50
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max LVIN values found in Table 3.
2. The symbol VIN, in this case, represents the LVIN symbols referenced in Table 2 and Table 3.
The following table shows the RGMII, and RTBI DC electrical characteristics when operating from a 2.5 V supply.
Table 24. RGMII and RTBI DC Electrical Characteristics
At recommended operating conditions with LVDD = 2.5 V
Parameter
Symbol
Min
Max
Unit
Note
Input high voltage
VIH
1.70
—
V
—
Input low voltage
VIL
—
0.70
V
—
Input high current (VIN = LVDD)
IIH
—
10
μA
1
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
54
Freescale Semiconductor
Ethernet Interface
Table 24. RGMII and RTBI DC Electrical Characteristics (continued)
At recommended operating conditions with LVDD = 2.5 V
Parameter
Symbol
Min
Max
Unit
Note
IIL
–15
—
μA
1, 2
Output high voltage (LVDD = min, IOH = –1.0 mA)
VOH
2.00
LVDD + 0.3
V
—
Output low voltage (LVDD = min, IOL = 1.0 mA)
VOL
GND – 0.3
0.40
V
—
Input low current (VIN = GND)
Note:
1. The symbol VIN, in this case, represents the LVIN symbols referenced in Table 2 and Table 3.
2. The min VILand max VIH values are based on the respective min and max LVIN values found in Table 3.
2.6.3
GMII, MII, RMII, SMII, TBI, RGMII, and RTBI AC Timing Specifications
This section describes the AC timing specifications for GMII, MII, RMII, SMII, TBI, RGMII, and RTBI.
2.6.3.1
GMII Timing Specifications
This section describe the GMII transmit and receive AC timing specifications.
2.6.3.1.1
GMII Transmit AC Timing Specifications
The following table provides the GMII transmit AC timing specifications.
Table 25. GMII Transmit AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
tGTX
7.5
—
8.5
ns
—
GMII data TXD[7:0], TX_ER, TX_EN setup time
tGTKHDV
2.5
—
—
ns
—
GTX_CLK to GMII data TXD[7:0], TX_ER, TX_EN delay
tGTKHDX
0.5
—
—
ns
—
GTX_CLK data clock rise time (20%–80%)
tGTXR
—
1.0
—
ns
—
GTX_CLK data clock fall time (80%–20%)
tGTXF
—
1.0
—
ns
—
GTX_CLK clock period
The following figure shows the GMII transmit AC timing diagram.
tGTXR
tGTX
GTX_CLK
tGTXH
tGTXF
TXD[7:0]
TX_EN
TX_ER
tGTKHDX
tGTKHDV
Figure 12. GMII Transmit AC Timing Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
55
Ethernet Interface
2.6.3.1.2
GMII Receive AC Timing Specifications
The following table provides the GMII receive AC timing specifications.
Table 26. GMII Receive AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
tGRX
7.5
—
—
ns
1
tGRXH/tGRX
35
—
65
%
2
RXD[7:0], RX_DV, RX_ER setup time to RX_CLK
tGRDVKH
2.0
—
—
ns
—
RXD[7:0], RX_DV, RX_ER hold time to RX_CLK
tGRDXKH
0.2
—
—
ns
—
RX_CLK clock rise time (20%–80%)
tGRXR
—
—
1.0
ns
2
RX_CLK clock fall time (80%–20%)
tGRXF
—
—
1.0
ns
2
RX_CLK clock period
RX_CLK duty cycle
Note:
1. The frequency of RX_CLK should not exceed frequency of gigabit Ethernet reference clock by more than 300 ppm
2. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing
The following figure provides the GMII AC test load.
Z0 = 50 Ω
Output
RL = 50 Ω
LVDD/2
Figure 13. GMII AC Test Load
The following figure shows the GMII receive AC timing diagram.
tGRXR
tGRX
RX_CLK
tGRXH
tGRXF
RXD[7:0]
RX_DV
RX_ER
tGRDXKH
tGRDVKH
Figure 14. GMII Receive AC Timing Diagram
2.6.3.2
MII AC Timing Specifications
This section describes the MII transmit and receive AC timing specifications.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
56
Freescale Semiconductor
Ethernet Interface
2.6.3.2.1
MII Transmit AC Timing Specifications
The following table provides the MII transmit AC timing specifications.
Table 27. MII Transmit AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
TX_CLK clock period 10 Mbps
tMTX
399.96
400
400.04
ns
—
TX_CLK clock period 100 Mbps
tMTX
39.996
40
40.004
ns
—
tMTXH/tMTX
35
—
65
%
—
tMTKHDX
0
—
25
ns
—
TX_CLK data clock rise (20%–80%)
tMTXR
1.0
—
4.0
ns
—
TX_CLK data clock fall (80%–20%)
tMTXF
1.0
—
4.0
ns
—
TX_CLK duty cycle
TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay
The following figure shows the MII transmit AC timing diagram.
tMTXR
tMTX
TX_CLK
tMTXH
tMTXF
TXD[3:0]
TX_EN
TX_ER
tMTKHDX
Figure 15. MII Transmit AC Timing Diagram
2.6.3.2.2
MII Receive AC Timing Specifications
The following table provides the MII receive AC timing specifications.
Table 28. MII Receive AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
RX_CLK clock period 10 Mbps
tMRX
399.96
400
400.04
ns
1
RX_CLK clock period 100 Mbps
tMRX
39.996
40
40.004
ns
1
tMRXH/tMRX
35
—
65
%
2
RXD[3:0], RX_DV, RX_ER setup time to RX_CLK
tMRDVKH
10.0
—
—
ns
RXD[3:0], RX_DV, RX_ER hold time to RX_CLK
tMRDXKH
10.0
—
—
ns
RX_CLK clock rise (20%–80%)
tMRXR
1.0
—
4.0
ns
2
RX_CLK clock fall time (80%–20%)
tMRXF
1.0
—
4.0
ns
2
RX_CLK duty cycle
Note:
1. The frequency of RX_CLK should not exceed the frequency of TX_CLK by more than 300 ppm.
2. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
57
Ethernet Interface
The following figure provides the MII AC test load.
Z0 = 50 Ω
Output
RL = 50 Ω
LVDD/2
Figure 16. MII AC Test Load
The following figure shows the MII receive AC timing diagram.
tMRXR
tMRX
RX_CLK
tMRXF
tMRXH
RXD[3:0]
RX_DV
RX_ER
Valid Data
tMRDVKH
tMRDXKL
Figure 17. MII Receive AC Timing Diagram
2.6.3.3
SMII AC Timing Specification
The following table shows the SMII timing specifications.
Table 29. SMII Mode Signal Timing
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Note
ETHSYNC_IN, ETHRXD to ETHCLOCK rising edge setup time
tSMDVKH
1.5
—
ns
—
ETHCLOCK rising edge to ETHSYNC_IN, ETHRXD hold time
tSMDXKH
1.0
—
ns
—
ETHCLOCK rising edge to ETHSYNC, ETHTXD output delay
tSMXR
1.5
5.5
ns
—
The following figure shows the SMII mode signal timing.
ETHCLOCK
tSMDVKH
tSMDXKH
ETHSYNC_IN
ETHRXD
Valid
tSMXR
ETHSYNC
ETHTXD
Valid
Valid
Figure 18. SMII Mode Signal Timing
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
58
Freescale Semiconductor
Ethernet Interface
2.6.3.4
RMII AC Timing Specifications
This section describes the RMII transmit and receive AC timing specifications.
2.6.3.4.1
RMII Transmit AC Timing Specifications
The following table shows the RMII transmit AC timing specifications.
Table 30. RMII Transmit AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
REF_CLK clock period
tRMT
—
20.0
—
ns
—
REF_CLK duty cycle
tRMTH
35
—
65
%
—
REF_CLK peak-to-peak jitter
tRMTJ
—
—
250
ps
—
Rise time REF_CLK (20%–80%)
tRMTR
1.0
—
4.0
ns
—
Fall time REF_CLK (80%–20%)
tRMTF
1.0
—
4.0
ns
—
tRMTDX
2.0
—
10.0
ns
—
REF_CLK to RMII data TXD[1:0], TX_EN delay
The following figure shows the RMII transmit AC timing diagram.
tRMTR
tRMT
REF_CLK
tRMTH
tRMTF
TXD[1:0]
TX_EN
TX_ER
tRMTDX
Figure 19. RMII Transmit AC Timing Diagram
2.6.3.4.2
RMII Receive AC Timing Specifications
The following table provides the RMII receive AC timing specifications.
Table 31. RMII Receive AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
REF_CLK clock period
tRMR
—
20.0
—
ns
—
REF_CLK duty cycle
tRMRH
35
—
65
%
1
REF_CLK peak-to-peak jitter
tRMRJ
—
—
250
ps
1
Rise time REF_CLK (20%–80%)
tRMRR
1.0
—
4.0
ns
1
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
59
Ethernet Interface
Table 31. RMII Receive AC Timing Specifications (continued)
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
Fall time REF_CLK (80%–20%)
tRMRF
1.0
—
4.0
ns
1
RXD[1:0], CRS_DV, RX_ER setup time to REF_CLK rising
edge
tRMRDV
4.0
—
—
ns
—
RXD[1:0], CRS_DV, RX_ER hold time to REF_CLK rising edge
tRMRDX
2.0
—
—
ns
—
Note:
1. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
The following figure provides the AC test load.
Z0 = 50 Ω
Output
RL = 50 Ω
LVDD/2
Figure 20. AC Test Load
The following figure shows the RMII receive AC timing diagram.
tRMRR
tRMR
REF_CLK
tRMRF
tRMRH
RXD[1:0]
CRS_DV
RX_ER
Valid Data
tRMRDVKH
tRMRKHDX
Figure 21. RMII Receive AC Timing Diagram
2.6.3.5
TBI AC Timing Specifications
This section describes the TBI transmit and receive AC timing specifications.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
60
Freescale Semiconductor
Ethernet Interface
2.6.3.5.1
TBI Transmit AC Timing Specifications
The following table provides the TBI transmit AC timing specifications.
Table 32. TBI Transmit AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
tGTX
—
8.0
—
ns
—
TCG[9:0] setup time GTX_CLK going high
tTTKHDV
2.0
—
—
ns
—
GTX_CLK to TCG[9:0] delay time
tTTKHDX
1.0
—
—
ns
1
GTX_CLK rise (20%–80%)
tTTXZ
0.7
—
—
ns
—
GTX_CLK fall time (80%–20%)
tTTXF
0.7
—
—
ns
—
GTX_CLK clock period
Note:
1. Data valid tTTKHDV to GTX_CLK minimum setup time is a function of clock and maximum hold time
(min setup = cycle time – max delay).
The following figure shows the TBI transmit AC timing diagram.
tTTXR
tTTX
GTX_CLK
tTTXH
tTTXF
TCG[9:0]
tTTKHDV
tTTKHDX
Figure 22. TBI Transmit AC Timing Diagram
2.6.3.5.2
TBI Receive AC Timing Specifications
The following table provides the TBI receive AC timing specifications.
Table 33. TBI Receive AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
PMA_RX_CLK[0:1] clock period
PMA_RX_CLK[0:1] skew
PMA_RX_CLK[0:1] duty cycle
RCG[9:0] setup time to rising PMA_RX_CLK
Symbol
Min
Typ
Max
Unit
Note
tTRX
—
16.0
—
ns
1
tSKTRX
7.5
—
8.5
ns
—
tTRXH/tTRX
40
—
60
%
2
tTRDVKH
2.5
—
—
ns
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
61
Ethernet Interface
Table 33. TBI Receive AC Timing Specifications (continued)
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
tTRDXKH
1.5
—
—
ns
—
PMA_RX_CLK[0:1] clock rise time (20%–80%)
tTRXR
0.7
—
2.4
ns
2
PMA_RX_CLK[0:1] clock fall time (80%–20%)
tTRXF
0.7
—
2.4
ns
2
RCG[9:0] hold time to rising PMA_RX_CLK
Note:
1. The frequency of RX_CLK should not exceed the frequency of gigabit Ethernet reference clock by more than 300 ppm.
2. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
The following figure provides the AC test load.
Z0 = 50 Ω
Output
RL = 50 Ω
LVDD/2
Figure 23. AC Test Load
The following figure shows the TBI receive AC timing diagram.
tTRXR
tTRX
PMA_RX_CLK1
tTRXH
RCG[9:0]
tTRXF
Valid Data
Valid Data
tTRDVKH
tSKTRX
tTRDXKH
PMA_RX_CLK0
tTRDXKH
tTRXH
tTRDVKH
Figure 24. TBI Receive AC Timing Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
62
Freescale Semiconductor
Ethernet Interface
2.6.3.6
TBI Single-Clock Mode AC Specifications
The following table shows the TBI single-clock mode receive AC timing specifications.
Table 34. TBI Single-Clock Mode Receive AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Typ
Max
Unit
Note
RX_CLK clock period
tTRR
7.5
8.0
8.5
ns
1
RX_CLK duty cycle
tTRRH
40
50
60
%
2
RX_CLK peak-to-peak jitter
tTRRJ
—
—
250
ps
2
Rise time RX_CLK (20%–80%)
tTRRR
—
—
—
ns
2
Fall time RX_CLK (80%–20%)
tTRRF
—
—
—
ns
2
RCG[9:0] setup time to RX_CLK rising edge
tTRRDV
2.0
—
—
ns
—
RCG[9:0] hold time to RX_CLK rising edge
tTRRDX
1.0
—
—
ns
—
Note:
1. The frequency of RX_CLK should not exceed the frequency of gigabit Ethernet reference clock by more than 300 ppm.
2. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
The following figure shows the TBI single-clock mode receive AC timing diagram.
tTRRR
tTRR
RX_CLK
tTRRF
tTRRH
Valid Data
RCG[9:0]
tTRRDV
tTRRDX
Figure 25. TBI Single-Clock Mode Receive AC Timing Diagram
2.6.3.7
RGMII and RTBI AC Timing Specifications
The following table presents the RGMII and RTBI AC timing specifications.
Table 35. RGMII and RTBI AC Timing Specifications
For recommended operating conditions, see Table 3
Symbol1
Min
Typ
Max
Unit
Notes
Data to clock output skew (at transmitter)
tSKRGT_TX
–500
0
500
ps
5
Data to clock input skew (at receiver)
tSKRGT_RX
1.2
—
2.6
ns
2
tRGT
7.2
8.0
8.8
ns
3
tRGTH/tRGT
40
50
60
%
3, 4, 6
Parameter
Clock period duration
Duty cycle for 10BASE-T and 100BASE-TX
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
63
Ethernet Interface
Table 35. RGMII and RTBI AC Timing Specifications (continued)
For recommended operating conditions, see Table 3
Symbol1
Min
Typ
Max
Unit
Notes
Duty cycle for Gigabit
tRGTH/tRGT
45
50
55
%
6
Rise time (20%–80%)
tRGTR
—
—
1.75
ns
6
Fall time (20%–80%)
tRGTF
—
—
1.75
ns
6
Parameter
Notes:
1. In general, the clock reference symbol representation for this section is based on the symbols RGT to represent RGMII and
RTBI timing. For example, the subscript of tRGT represents the TBI (T) receive (RX) clock. Note also that the notation for rise
(R) and fall (F) times follows the clock symbol that is being represented. For symbols representing skews, the subscript is
skew (SK) followed by the clock that is being skewed (RGT).
2. This implies that PC board design will require clocks to be routed such that an additional trace delay of greater than 1.5 ns is
added to the associated clock signal. Many PHY vendors already incorporate the necessary delay inside their chip. If so,
additional PCB delay is probably not needed.
3. For 10 and 100 Mbps, tRGT scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively.
4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long
as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned
between.
5. The frequency of RX_CLK should not exceed the frequency of gigabit ethernet reference clock by more than 300 ppm.
6. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
64
Freescale Semiconductor
Ethernet Interface
The following figure shows the RGMII and RTBI AC timing and multiplexing diagrams.
tRGT
tRGTH
GTX_CLK
(At Transmitter)
tSKRGT_TX
TXD[8:5][3:0]
TXD[7:4][3:0]
TX_CTL
TXD[3:0]
TXD[8:5]
TXD[7:4]
TXD[4]
TXEN
TXD[9]
TXERR
tSKRGT_RX
TX_CLK
(At PHY)
tRGTH
tRGT
GTX_CLK
(At Receiver)
RXD[8:5][3:0]
RXD[7:4][3:0]
RXD[8:5]
RXD[3:0] RXD[7:4]
RX_CTL
RXD[9]
RXERR
tSKRGT_TX
RXD[4]
RXDV
tSKRGT_RX
RX_CLK
(At PHY)
Figure 26. RGMII and RTBI AC Timing and Multiplexing Diagrams
2.6.4
SGMII Interface Electrical Characteristics
Each SGMII port features a 4-wire AC-coupled serial link from the SerDes interface of MPC8569E as shown in Figure 27,
where CTX is the external (on board) AC-coupled capacitor. Each output pin of the SerDes transmitter differential pair features
50-Ω output impedance. Each input of the SerDes receiver differential pair features 50-Ω on-die termination to GND. The
reference circuit of the SerDes transmitter and receiver is shown in Figure 45.
2.6.4.1
SGMII DC Electrical Characteristics
This section discusses the electrical characteristics for the SGMII interface.
2.6.4.1.1
DC Requirements for SGMII SD_REF_CLK and SD_REF_CLK
The characteristics and DC requirements of the separate SerDes reference clock are described in Section 2.9.2.3, “DC Level
Requirement for SerDes Reference Clocks.”
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
65
Ethernet Interface
2.6.4.1.2
SGMII Transmit DC Timing Specifications
Table 36 and Table 37 describe the SGMII SerDes transmitter and receiver AC-coupled DC electrical characteristics.
Transmitter DC characteristics are measured at the transmitter outputs, SD_TX[n] and SD_TX[n], as shown in Figure 28.
Table 36. SGMII DC Transmitter Electrical Characteristics
At recommended operating conditions with XVDD = 1.0 V ± 3% and 1.1 V ± 3%.
Parameter
Symbol
Min
Typ
Max
Unit
Notes
Output high voltage
VOH
—
—
XVDD-Typ/2 +
|VOD|-max/2
mV
1
Output low voltage
VOL
XVDD-Typ/2 –
|VOD|-max/2
—
—
mV
1
|VOD|
320.0
500.0
725.0
mV
Equalization
setting: 1.0×
293.8
459.0
665.6
Equalization
setting: 1.09×
266.9
417.0
604.7
Equalization
setting: 1.2×
240.6
376.0
545.2
Equalization
setting: 1.33×
213.1
333.0
482.9
Equalization
setting: 1.5×
186.9
292.0
423.4
Equalization
setting: 1.71×
160.0
250.0
362.5
Equalization
setting: 2.0×
Output differential voltage2, 3, 4
(XVDD-Typ at 1.0 V)
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
66
Freescale Semiconductor
Ethernet Interface
Table 36. SGMII DC Transmitter Electrical Characteristics (continued)
At recommended operating conditions with XVDD = 1.0 V ± 3% and 1.1 V ± 3%.
Parameter
voltage2, 3, 4
Output differential
(XVDD-Typ at 1.1 V)
Output impedance (single-ended)
Symbol
Min
Typ
Max
Unit
Notes
|VOD|
352.0
550.0
797.5
mV
Equalization
setting: 1.0×
323.1
504.9
732.1
Equalization
setting: 1.09×
293.6
458.7
665.1
Equalization
setting: 1.2×
264.7
413.6
599.7
Equalization
setting: 1.33×
234.4
366.3
531.1
Equalization
setting: 1.5×
205.6
321.2
465.7
Equalization
setting: 1.71×
176.0
275.0
398.8
Equalization
setting: 2.0×
40
50
60
RO
Ω
—
Notes:
1. This does l not align to DC-coupled SGMII.
2. |VOD| = |VSD_TXn – VSD_TXn|. |VOD| is also referred as output differential peak voltage. VTX-DIFFp-p = 2 × |VOD|.
3. The |VOD| value shown in the table assumes the following transmit equalization setting in the XMITEQAB (for SerDes lanes
0 & 1) or XMITEQEF (for SerDes lanes 2 & 3) bit field of the MPC8569E SerDes control register:
• The MSB (bit 0) of the above bit field is set to zero (selecting the full VDD-DIFF-p-p amplitude—power up default);
• The LSB (bit [1:3]) of the above bit field is set based on the equalization setting shown in table.
4. The |VOD| value shown in the Typ column is based on the condition of XVDD-Typ = 1.0V and 1.1 V, no common mode offset
variation, SerDes transmitter is terminated with 100-Ω differential load between SD_TX[n] and SD_TX[n].
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
67
Ethernet Interface
The following figure shows an example of a 4-wire AC-coupled SGMII serial link connection.
50 Ω
SD_TXn
CTX
SD_RXm
50 Ω
Transmitter
Receiver
50 Ω
SD_TXn
MPC8569E SGMII
SerDes Interface
Receiver
SD_RXn
CTX
SD_RXm
SD_TXm
CTX
50 Ω
50 Ω
50 Ω
Transmitter
50 Ω
50 Ω
SD_RXn
CTX
SD_TXm
Figure 27. 4-Wire AC-Coupled SGMII Serial Link Connection Example
The following figure shows the SGMII transmitter DC measurement circuit.
MPC8569E SGMII
SerDes Interface
50 Ω SD_TXn
50 Ω
Transmitter
VOD
50 Ω
SD_TXn
50 Ω
Figure 28. SGMII Transmitter DC Measurement Circuit
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
68
Freescale Semiconductor
Ethernet Interface
2.6.4.1.3
SGMII DC Receiver Electrical Characteristics
The following table lists the SGMII DC receiver electrical characteristics. Source synchronous clocking is not supported. Clock
is recovered from the data.
s
Table 37. SGMII DC Receiver Electrical Characteristics
At recommended operating conditions with XVDD = 1.0 V ± 3% and 1.1 V ± 3%.
Parameter
Symbol
DC Input voltage range
Input differential voltage
—
LSTS = 001
VRX_DIFFp-p
LSTS = 100
Loss of signal threshold
Min
LSTS = 001
VLOS
LSTS = 100
Receiver differential input impedance
ZRX_DIFF
Typ
Max
Unit
Notes
—
1
1200
mV
2, 4
mV
3, 4
Ω
—
N/A
100
—
175
—
30
—
100
65
—
175
80
—
120
Notes:
1. Input must be externally AC-coupled.
2. VRX_DIFFp-p is also referred to as peak-to-peak input differential voltage.
3. The concept of this parameter is equivalent to the electrical idle detect threshold parameter in PCI Express. See
Section 2.10.2, “PCI Express DC Physical Layer Specifications,” and Section 2.10.3, “PCI Express AC Physical Layer
Specifications,” for further explanation.
4. The LSTS shown in this table refers to the LSTS2 or LSTS3 bit field of the MPC8569E‘s SerDes control register SRDSCR4.
2.6.4.2
SGMII AC Timing Specifications
This section discusses the AC timing specifications for the SGMII interface.
2.6.4.2.1
AC Requirements for SGMII SD_REF_CLK and SD_REF_CLK
Note that the SGMII clock requirements for SD_REF_CLK and SD_REF_CLK are intended to be used within the clocking
guidelines specified by Section 2.9.2.4, “AC Requirements for SerDes Reference Clocks.”
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
69
Ethernet Interface
2.6.4.2.2
SGMII Transmit AC Timing Specifications
The following table provides the SGMII transmit AC timing specifications. A source synchronous clock is not supported. The
AC timing specifications do not include RefClk jitter.
Table 38. SGMII Transmit AC Timing Specifications
At recommended operating conditions with XVDD = 1.0 V ± 3% and 1.1 V ± 3%.
Parameter
Symbol
Min
Typ
Max
Unit
Notes
Deterministic jitter
JD
—
—
0.17
UI p-p
—
Total jitter
JT
—
—
0.35
UI p-p
2
Unit interval
UI
799.92
800
800.08
ps
1
CTX
10
—
200
nF
3
AC coupling capacitor
Notes:
1. Each UI is 800 ps ± 100 ppm.
2. See Figure 30 for single frequency sinusoidal jitter limits.
3. The external AC coupling capacitor is required. It is recommended that it be placed near the device transmitter outputs.
2.6.4.2.3
SGMII AC Measurement Details
Transmitter and receiver AC characteristics are measured at the transmitter outputs (SD_TXn and SD_TXn) or at the receiver
inputs (SD_RXn and SD_RXn), as depicted in the following figure, respectively.
D+ Package
Pin
C = CTX
TX
Silicon
+ Package
D– Package
Pin
C = CTX
R = 50 Ω
R = 50 Ω
Figure 29. SGMII AC Test/Measurement Load
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
70
Freescale Semiconductor
Ethernet Interface
2.6.4.2.4
SGMII Receiver AC Timing Specifications
The following table provides the SGMII receive AC timing specifications. The AC timing specifications do not include RefClk
jitter. Source synchronous clocking is not supported. Clock is recovered from the data.
Table 39. SGMII Receive AC Timing Specifications
At recommended operating conditions with XVDD = 1.0 V ± 3%. and 1.1 V ± 3%.
Parameter
Deterministic Jitter Tolerance
Combined Deterministic and Random Jitter Tolerance
Total Jitter Tolerance
Bit Error Ratio
Unit Interval
Symbol
Min
Typ
Max
Unit
Notes
JD
0.37
—
—
UI p-p
1, 2, 4
JDR
0.55
—
—
UI p-p
1, 2, 4
JT
0.65
—
—
UI p-p
1, 2, 4
BER
—
—
10-12
—
—
UI
799.92
800.00
800.08
ps
3
Notes:
1. Measured at receiver.
2. See RapidIO 1x/4x LP Serial Physical Layer Specification for interpretation of jitter specifications.
3. Each UI is 800 ps ± 100 ppm.
4. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
The sinusoidal jitter in the total jitter tolerance may have any amplitude and frequency in the unshaded region of the following
figure.
Sinusoidal Jitter Amplitude
8.5 UI p-p
0.10 UI p-p
22.1 kHz
Frequency
1.875 MHz
20 MHz
Figure 30. Single Frequency Sinusoidal Jitter Limits
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
71
Ethernet Interface
2.6.5
2.6.5.1
QUICC Engine Block IEEE 1588 Electrical Characteristics
QUICC Engine Block IEEE 1588 DC Specifications
The following table shows the QUICC Engine block IEEE 1588 DC specifications when operating from a 3.3 V supply.
Table 40. QUICC Engine Block IEEE 1588 DC Electrical Characteristics
At recommended operating conditions with OVDD = 3.3 V
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2.0
—
V
1
Input low voltage
VIL
—
0.90
V
—
Input high current (VIN = OVDD)
IIH
—
40
μA
2
Input low current (VIN = GND)
IIL
–600
—
μA
2
Output high voltage (OVDD = min, IOH = –4.0 mA)
VOH
2.1
OVDD + 0.3
V
—
Output low voltage (OVDD = min, IOL = 4.0 mA)
VOL
GND
0.50
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol VIN, in this case, represents the OVIN symbols referenced in Table 2 and Table 3.
2.6.5.2
QUICC Engine Block IEEE 1588 AC Specifications
The following table provides the QUICC Engine block IEEE 1588 AC timing specifications.
Table 41. QUICC Engine Block IEEE 1588 AC Timing Specifications
Parameter
Symbol
Min
Typ
Max
Unit
Notes
tT1588CLK
3.8
—
TRX_CLK × 7
ns
1, 3
QE_1588_CLK duty cycle
tT1588CLKH/
tT1588CLK
40
50
60
%
5
QE_1588_CLK peak-to-peak jitter
tT1588CLKINJ
—
—
250
ps
5
Rise time QE_1588_CLK (20%–80%)
tT1588CLKINR
1.0
—
2.0
ns
5
Fall time QE_1588_CLK (80%–20%)
tT1588CLKINF
1.0
—
2.0
ns
5
QE_1588_CLK_OUT clock period
tT1588CLKOUT
2 × tT1588CLK
—
—
ns
—
QE_1588_CLK_OUT duty cycle
tT1588CLKOTH/
tT1588CLKOUT
30
50
70
%
—
tT1588OV
0.5
—
4.0
ns
—
QE_1588_CLK clock period
QE_1588_PPS_OUT
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
72
Freescale Semiconductor
Ethernet Interface
Table 41. QUICC Engine Block IEEE 1588 AC Timing Specifications (continued)
Parameter
QE_1588_TRIG_IN pulse width
Symbol
Min
Typ
Max
Unit
Notes
tT1588TRIGH
2 × tT1588CLK_
—
—
ns
2
MAX
QE_PTP_SOF_TX_IN pulse width
tT1588TRIGH
TTX_CLK × 2
—
—
ns
4
QE_PTP_SOF_RX_IN pulse width
tT1588TRIGH
TRX_CLK × 2
—
—
ns
4
Notes:
1. TRX_CLK is the max clock period of the QUICC Engine block’s receiving clock selected by TMR_CTRL[CKSEL]. See the
QUICC Engine Block with Protocol Interworking Reference Manual, for a description of TMR_CTRL registers.
2. It needs to be at least two times the clock period of the clock selected by TMR_CTRL[CKSEL]. See the QUICC Engine Block
with Protocol Interworking Reference Manual, for a description of TMR_CTRL registers.
3. The maximum value of tT1588CLK is not only defined by the value of tRX_CLK, but also defined by the recovered clock. For
example, for 10/100/1000 Mbps modes, the maximum value of tT1588CLK are 2800, 280, and 56 ns, respectively.
4. The minimum value of tTX/RXCLK is defined by the recovered clock. For example, for 10/100/1000 Mbps modes, the value of
tTX/RXCLK are 800, 80, and 16 ns, respectively.
5. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
The following figure shows the data and command output AC timing diagram.
tT1588CLKOUT
tT1588CLKOUTH
QE_1588_CLK_OUT
tT1588OV
QE_1588_PPS_OUT
1QUICC
Engine block IEEE 1588 Output AC timing: The output delay is counted starting at the rising
edge if tT11588CLKOUT is non-inverting. Otherwise, it is counted starting at the falling edge.
Figure 31. QUICC Engine Block IEEE 1588 Output AC Timing
The following figure shows the data and command input AC timing diagram.
tT1588CLK
tT1588CLKH
QE_1588_CLK
QE_1588_TRIG_IN
tT1588TRIGH
Figure 32. QUICC Engine Block IEEE 1588 Input AC Timing
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
73
Ethernet Management Interface
The following figure shows the data and command input AC timing diagram.
tTTX/RXCLK
tT1588CLKH
TX_CLK/RX_CLK
QE_PTP_SOF_TX_IN/
QE_PTP_SOF_RX_IN
tT1588TRIGH
Figure 33. QUICC Engine Block IEEE 1588 Input AC Timing (SOF TRIG)
2.7
Ethernet Management Interface
The electrical characteristics specified in this section apply to the MII management interface signals management data
input/output (MDIO) and management data clock (MDC). The electrical characteristics for GMII, RGMII, TBI, and RTBI are
specified in Section 2.6, “Ethernet Interface.”
2.7.1
MII Management DC Electrical Characteristics
The MDC and MDIO are defined to operate at a supply voltage of 3.3 V. The following table provides the DC electrical
characteristics for MDIO and MDC.
Table 42. MII Management DC Electrical Characteristics
At recommended operating conditions with LVDD = 3.3 V
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2.0
—
V
—
Input low voltage
VIL
—
0.90
V
—
Input high current (LVDD = Max, VIN = 2.1 V)
IIH
—
40
μA
1
Input low current (LVDD = Max, VIN = 0.5 V)
IIL
–600
—
μA
1
Output high voltage (LVDD = Min, IOH = –4.0 mA)
VOH
2.4
—
V
—
Output low voltage (LVDD = Min, IOL = 4.0 mA)
VOL
—
0.4
V
—
Note:
1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 2 and Table 3.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
74
Freescale Semiconductor
Ethernet Management Interface
2.7.1.1
MII Management AC Electrical Specifications
The following table provides the MII management AC timing specifications.
Table 43. MII Management AC Timing Specifications
At recommended operating conditions with LVDD = 3.3 V ± 5%.
Symbol1
Min
Typ
Max
Unit
Notes
MDC frequency
fMDC
—
2.5
—
MHz
2
MDC period
tMDC
—
400
—
ns
—
MDC clock pulse width high
tMDCH
32
—
—
ns
—
MDC to MDIO valid
tMDKHDV
2×(tplb_clk*8)
—
—
ns
4
MDC to MDIO delay
tMDKHDX
(16 × tplb_clk) – 3
—
(16 × tplb_clk) + 3
ns
3, 4, 5
MDIO to MDC setup time
tMDDVKH
10
—
—
ns
—
MDIO to MDC hold time
tMDDXKH
0
—
—
ns
—
MDC rise time
tMDCR
—
—
10
ns
—
MDC fall time
tMDCF
—
—
10
ns
—
Parameter
Notes:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management
data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time.
Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reaching the valid
state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter
convention is used with the appropriate letter: R (rise) or F (fall).
2. This parameter is dependent on the platform clock frequency (MIIMCFG [MgmtClk] field determines the clock frequency of
the Mgmt Clock CE_MDC).
3. This parameter is dependent on the platform clock frequency. The delay is equal to 16 platform clock periods ±3 ns. For
example, with a platform clock of 400 MHz, the min/max delay is 40 ns ± 3 ns.
4. tplb_clk is the QUICC Engine block clock/2.
5. MDC to MDIO Data valid tMDKHDV is a function of clock period and max delay time (tMDKHDX).
(Min setup = cycle time – max delay
The following figure shows the MII management AC timing diagram.
tMDCR
tMDC
MDC
tMDCH
tMDCF
MDIO
(Input)
tMDDVKH
tMDDXKH
MDIO
(Output)
tMDKHDX
Figure 34. MII Management Interface Timing Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
75
HDLC, BISYNC, Transparent, and Synchronous UART Interfaces
2.8
HDLC, BISYNC, Transparent, and Synchronous UART Interfaces
This section describes the DC and AC electrical specifications for the high level data link control (HDLC), BISYNC,
transparent, and synchronous UART interfaces of the MPC8569E.
2.8.1
HDLC, BISYNC, Transparent, and Synchronous UART DC Electrical
Characteristics
The following table provides the DC electrical characteristics for the HDLC, BISYNC, Transparent, and synchronous UART
interfaces.
Table 44. HDLC, BISYNC, and Transparent DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
2.8.2
HDLC, BISYNC, Transparent, and Synchronous UART AC Timing
Specifications
The following table provides the input and output AC timing specifications for the HDLC, BISYNC, and Transparent protocols.
Table 45. HDLC, BISYNC, and Transparent AC Timing Specifications
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Notes
Outputs—Internal clock delay
tHIKHOV
0
5.5
ns
2
Outputs—External clock delay
tHEKHOV
1
8.4
ns
2
Outputs—Internal clock high Impedance
tHIKHOX
0
5.5
ns
2
Outputs—External clock high Impedance
tHEKHOX
1
8
ns
2
tHIIVKH
6
—
ns
—
Characteristic
Inputs—Internal clock input setup time
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
76
Freescale Semiconductor
HDLC, BISYNC, Transparent, and Synchronous UART Interfaces
Table 45. HDLC, BISYNC, and Transparent AC Timing Specifications (continued)
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Notes
Inputs—External clock input setup time
tHEIVKH
4
—
ns
—
Inputs—Internal clock input hold time
tHIIXKH
0
—
ns
—
Inputs—External clock input hold time
tHEIXKH
1.3
—
ns
—
Characteristic
Notes:
1. The symbols used for timing specifications follow the pattern t(first two letters of functional block)(signal)(state)(reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tHIKHOX symbolizes the outputs internal
timing (HI) for the time tserial memory clock reference (K) goes from the high state (H) until outputs (O) are invalid (X).
2. Output specifications are measured from the 50% level of the rising edge of CLKIN to the 50% level of the signal. Timings
are measured at the pin.
The following table provides the input and output AC timing specifications for the synchronous UART protocols.
Table 46. Synchronous UART AC Timing Specifications
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Notes
Outputs—Internal clock delay
tHIKHOV
0
11
ns
2
Outputs—External clock delay
tHEKHOV
1
14
ns
2
Outputs—Internal clock high Impedance
tHIKHOX
0
11
ns
2
Outputs—External clock high Impedance
tHEKHOX
1
14
ns
2
Inputs—Internal clock input setup time
tHIIVKH
10
—
ns
—
Inputs—External clock input setup time
tHEIVKH
8
—
ns
—
Inputs—Internal clock input hold time
tHIIXKH
0
—
ns
—
Inputs—External clock input hold time
tHEIXKH
1
—
ns
—
Characteristic
Notes:
1. The symbols used for timing specifications follow the pattern t(first two letters of functional block)(signal)(state)(reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tHIKHOX symbolizes the outputs internal
timing (HI) for the time tserial memory clock reference (K) goes from the high state (H) until outputs (O) are invalid (X).
2. Output specifications are measured from the 50% level of the rising edge of CLKIN to the 50% level of the signal. Timings
are measured at the pin.
The following figure provides the AC test load.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 35. AC Test Load
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
77
High-Speed SerDes Interfaces (HSSI)
Figure 36 and Figure 37 represent the AC timing from Table 45 and Table 46. Note that although the specifications generally
refer to the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge. Also note
that the clock edge is selectable.
The following figure shows the timing with external clock.
Serial CLK (Input)
tHEIXKH
tHEIVKH
Input Signals:
(See Note)
tHEKHOV
Output Signals:
(See Note)
tHEKHOX
Note: The clock edge is selectable.
Figure 36. AC Timing (External Clock) Diagram
The following figure shows the timing with internal clock.
Serial CLK (Output)
tHIIVKH
tHIIXKH
Input Signals:
tHIKHOV
Output Signals:
tHIKHOX
Figure 37. AC Timing (Internal Clock) Diagram
2.9
High-Speed SerDes Interfaces (HSSI)
The MPC859E features a serializer/deserializer (SerDes) interface to be used for high-speed serial interconnect
applications.The SerDes interface can be used for PCI Express and/or Serial RapidIO and/or SGMII data transfers.
This section describes the common portion of SerDes DC electrical specifications, which is the DC requirement for SerDes
reference clocks. The SerDes data lane’s transmitter (Tx) and receiver (Rx) reference circuits are also shown.
2.9.1
Signal Terms Definition
The SerDes utilizes differential signaling to transfer data across the serial link. This section defines terms used in the description
and specification of differential signals.
The below figure shows how the signals are defined. For illustration purposes only, one SerDes lane is used in the description.
The following figure shows the waveform for either a transmitter output (SDn_TX and SDn_TX) or a receiver input (SDn_RX
and SDn_RX). Each signal swings between A volts and B volts where A > B.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
78
Freescale Semiconductor
High-Speed SerDes Interfaces (HSSI)
SDn_TX or
SDn_RX
A Volts
Vcm = (A + B)/2
SDn_TX or
SDn_RX
B Volts
Differential Swing, VID or VOD = A – B
Differential Peak Voltage, VDIFFp = |A – B|
Differential Peak-Peak Voltage, VDIFFpp = 2 * VDIFFp (not shown)
Figure 38. Differential Voltage Definitions for Transmitter or Receiver
Using this waveform, the definitions are as shown in the following list. To simplify the illustration, the definitions assume that
the SerDes transmitter and receiver operate in a fully symmetrical differential signaling environment:
Single-Ended Swing
The transmitter output signals and the receiver input signals SD_TX, SD_TX, SD_RX and SD_RX
each have a peak-to-peak swing of A – B volts. This is also referred as each signal wire’s
single-ended swing.
Differential Output Voltage, VOD (or Differential Output Swing):
The differential output voltage (or swing) of the transmitter, VOD, is defined as the difference of
the two complimentary output voltages: VSD_TX – VSD_TX. The VOD value can be either positive
or negative.
Differential Input Voltage, VID (or Differential Input Swing):
The differential input voltage (or swing) of the receiver, VID, is defined as the difference of the two
complimentary input voltages: VSD_RX – VSD_RX. The VID value can be either positive or
negative.
Differential Peak Voltage, VDIFFp
The peak value of the differential transmitter output signal or the differential receiver input signal
is defined as the differential peak voltage, VDIFFp = |A – B| volts.
Differential Peak-to-Peak, VDIFFp-p
Since the differential output signal of the transmitter and the differential input signal of the receiver
each range from A – B to –(A – B) volts, the peak-to-peak value of the differential transmitter
output signal or the differential receiver input signal is defined as differential peak-to-peak voltage,
VDIFFp-p = 2 × VDIFFp = 2 × |(A – B)| volts, which is twice the differential swing in amplitude, or
twice of the differential peak. For example, the output differential peak-peak voltage can also be
calculated as VTX-DIFFp-p = 2 × |VOD|.
Differential Waveform
The differential waveform is constructed by subtracting the inverting signal (SD_TX, for example)
from the non-inverting signal (SD_TX, for example) within a differential pair. There is only one
signal trace curve in a differential waveform. The voltage represented in the differential waveform
is not referenced to ground. See Figure 43 as an example for differential waveform.
Common Mode Voltage, Vcm
The common mode voltage is equal to half of the sum of the voltages between each conductor of
a balanced interchange circuit and ground. In this example, for SerDes output,
Vcm_out = (VSD_TX + VSD_TX) ÷ 2 = (A + B) ÷ 2, which is the arithmetic mean of the two
complimentary output voltages within a differential pair. In a system, the common mode voltage
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
79
High-Speed SerDes Interfaces (HSSI)
may often differ from one component’s output to the other’s input. It may be different between the
receiver input and driver output circuits within the same component. It is also referred to as the DC
offset on some occasions.
To illustrate these definitions using real values, consider the example of a current mode logic (CML) transmitter that has a
common mode voltage of 2.25 V and outputs, TD and TD. If these outputs have a swing from 2.0 V to 2.5 V, the peak-to-peak
voltage swing of each signal (TD or TD) is 500 mV p-p, which is referred to as the single-ended swing for each signal. Because
the differential signaling environment is fully symmetrical in this example, the transmitter output’s differential swing (VOD) has
the same amplitude as each signal’s single-ended swing. The differential output signal ranges between 500 mV and –500 mV.
In other words, VOD is 500 mV in one phase and –500 mV in the other phase. The peak differential voltage (VDIFFp) is 500 mV.
The peak-to-peak differential voltage (VDIFFp-p) is 1000 mV p-p.
2.9.2
SerDes Reference Clocks
The SerDes reference clock inputs are applied to an internal PLL whose output creates the clock used by the corresponding
SerDes lanes.The SerDes reference clock inputs are SD_REF_CLK and SD_REF_CLK for PCI Express, Serial RapidIO, and
SGMII interface, respectively.
The following sections describe the SerDes reference clock requirements and provide application information.
2.9.2.1
SerDes Spread Spectrum Clock Source Recommendations
SD_REF_CLK/SD_REF_CLK are designed to work with spread spectrum clock for PCI Express protocol only with the
spreading specification defined in Table 47. When using spread spectrum clocking for PCI Express, both ends of the link
partners should use the same reference clock. For best results, a source without significant unintended modulation must be used.
The spread spectrum clocking cannot be used if the same SerDes reference clock is shared with other non-spread spectrum
supported protocols. For example, if the spread spectrum clocking is desired on a SerDes reference clock for PCI Express and
the same reference clock is used for any other protocol such as SGMII/SRIO due to the SerDes lane usage mapping option,
spread spectrum clocking cannot be used at all.
Table 47. SerDes Spread Spectrum Clock Source Recommendations
At recommended operating conditions. See Table 3.
Parameter
Min
Max
Unit
Notes
Frequency modulation
30
33
kHz
—
Frequency spread
+0
–0.5
%
1
Note:
1. Only down spreading is allowed.
2.9.2.2
SerDes Reference Clock Receiver Characteristics
The following figure shows a receiver reference diagram of the SerDes reference clocks.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
80
Freescale Semiconductor
High-Speed SerDes Interfaces (HSSI)
50 Ω
SD_REF_CLK
Input
Amp
SD_REF_CLK
50 Ω
Figure 39. Receiver of SerDes Reference Clocks
The characteristics of the clock signals are as follows:
•
•
•
•
The supply voltage requirements for XVDD are as specified in Table 3.
The SerDes reference clock receiver reference circuit structure is as follows:
— The SD_REF_CLK and SD_REF_CLK are internally AC-coupled differential inputs as shown in Figure 39. Each
differential clock input (SD_REF_CLK or SD_REF_CLK) has a 50-Ω termination to SCOREGND followed by
on-chip AC-coupling.
— The external reference clock driver must be able to drive this termination.
— The SerDes reference clock input can be either differential or single-ended. See the differential mode and
single-ended mode description below for further detailed requirements.
The maximum average current requirement that also determines the common mode voltage range
— When the SerDes reference clock differential inputs are DC-coupled externally with the clock driver chip, the
maximum average current allowed for each input pin is 8 mA. In this case, the exact common mode input voltage
is not critical as long as it is within the range allowed by the maximum average current of 8 mA because the input
is AC-coupled on-chip.
— This current limitation sets the maximum common mode input voltage to be less than 0.4 V (0.4 V ÷ 50 = 8 mA)
while the minimum common mode input level is 0.1 V above SCOREGND. For example, a clock with a 50/50
duty cycle can be produced by a clock driver with output driven by its current source from 0 to 16 mA (0–0.8 V),
such that each phase of the differential input has a single-ended swing from 0 V to 800 mV with the common mode
voltage at 400 mV.
— If the device driving the SD_REF_CLK and SD_REF_CLK inputs cannot drive 50 Ω to SCOREGND DC, or it
exceeds the maximum input current limitations, then it must be AC-coupled off-chip.
The input amplitude requirement
— This requirement is described in detail in the following sections.
2.9.2.3
DC Level Requirement for SerDes Reference Clocks
The DC level requirement for the SerDes reference clock inputs is different depending on the signaling mode used to connect
the clock driver chip and SerDes reference clock inputs as described below.
•
Differential mode
— The input amplitude of the differential clock must be between 400 and 1600 mV differential peak-peak (or
between 200 and 800 mV differential peak). In other words, each signal wire of the differential pair must have a
single-ended swing less than 800 mV and greater than 200 mV. This requirement is the same for both external DCor AC-coupled connections.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
81
High-Speed SerDes Interfaces (HSSI)
— For external DC-coupled connection, as described in Section 2.9.2.2, “SerDes Reference Clock Receiver
Characteristics,” the maximum average current requirements sets the requirement for average voltage (common
mode voltage) to be between 100 and 400 mV. The following figure shows the SerDes reference clock input
requirement for DC-coupled connection scheme.
200 mV < Input Amplitude or Differential Peak < 800 mV
SD_REF_CLK
Vmax < 800 mV
100 mV < Vcm < 400 mV
SD_REF_CLK
Vmin > 0 V
Figure 40. Differential Reference Clock Input DC Requirements (External DC-Coupled)
— For external AC-coupled connection, there is no common mode voltage requirement for the clock driver. Since
the external AC-coupling capacitor blocks the DC level, the clock driver and the SerDes reference clock receiver
operate in different command mode voltages. The SerDes reference clock receiver in this connection scheme has
its common mode voltage set to SCOREGND. Each signal wire of the differential inputs is allowed to swing
below and above the command mode voltage (SCOREGND). The following figure shows the SerDes reference
clock input requirement for AC-coupled connection scheme.
200 mV < Input Amplitude or Differential Peak < 800 mV
SD_REF_CLK
Vmax < Vcm + 400 mV
Vcm
SD_REF_CLK
Vmin
> Vcm – 400 mV
Figure 41. Differential Reference Clock Input DC Requirements (External AC-Coupled)
•
Single-ended mode
— The reference clock can also be single-ended. The SD_REF_CLK input amplitude (single-ended swing) must be
between 400 and 800 mV peak-peak (from Vmin to Vmax) with SD_REF_CLK either left unconnected or tied to
ground.
— The SD_REF_CLK input average voltage must be between 200 and 400 mV. Figure 42 shows the SerDes
reference clock input requirement for single-ended signaling mode.
— To meet the input amplitude requirement, the reference clock inputs might need to be DC- or AC-coupled
externally. For the best noise performance, the reference of the clock could be DC- or AC-coupled into the unused
phase (SD_REF_CLK) through the same source impedance as the clock input (SD_REF_CLK) in use.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
82
Freescale Semiconductor
High-Speed SerDes Interfaces (HSSI)
400 mV < SD_REF_CLK Input Amplitude < 800 mV
SD_REF_CLK
0V
SD_REF_CLK
Figure 42. Single-Ended Reference Clock Input DC Requirements
2.9.2.4
AC Requirements for SerDes Reference Clocks
The following table lists AC requirements for the PCI Express, SGMII, and Serial RapidIO SerDes reference clocks to be
guaranteed by the customer’s application design.
Table 48. SD_REF_CLK and SD_REF_CLK Input Clock Requirements
At recommended operating conditions with ScoreVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typ
Max
Unit
Notes
SD_REF_CLK/SD_REF_CLK frequency range
tCLK_REF
—
100/125
—
MHz
1
SD_REF_CLK/SD_REF_CLK clock frequency
tolerance
tCLK_TOL
–350
—
350
ppm
—
tCLK_DUTY
40
50
60
%
7
SD_REF_CLK/SD_REF_CLK max deterministic
peak-peak jitter at 10-6 BER
tCLK_DJ
—
—
42
ps
7
SD_REF_CLK/SD_REF_CLK total reference clock
jitter at 10-6 BER (peak-to-peak jitter at refClk input)
tCLK_TJ
—
—
86
ps
2, 7
SD_REF_CLK/SD_REF_CLK rising/falling edge rate
tCLKRR/tCLKFR
1
—
4
V/ns
3, 7
SD_REF_CLK/SD_REF_CLK reference clock duty
cycle
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
83
High-Speed SerDes Interfaces (HSSI)
Table 48. SD_REF_CLK and SD_REF_CLK Input Clock Requirements (continued)
At recommended operating conditions with ScoreVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typ
Max
Unit
Notes
Differential input high voltage
VIH
200
—
—
mV
4
Differential input low voltage
VIL
—
—
–200
mV
4
Rise-Fall
Matching
—
—
20
%
5, 6, 7
Rising edge rate (SDn_REF_CLK) to falling edge rate
(SDn_REF_CLK) matching
Notes:
1. Caution: Only 100 and 125 have been tested. In-between values will not work correctly with the rest of the system.
2. Limits from PCI Express CEM Rev 2.0
3. Measured from –200 mV to +200 mV on the differential waveform (derived from SD_REF_CLK minus SD_REF_CLK). The
signal must be monotonic through the measurement region for rise and fall time. The 400 mV measurement window is
centered on the differential zero crossing. See Figure 43.
4. Measurement taken from differential waveform
5. Measurement taken from single-ended waveform
6. Matching applies to rising edge for SD_REF_CLK and falling edge rate for SD_REF_CLK. It is measured using a 200 mV
window centered on the median cross point where SD_REF_CLK rising meets SD_REF_CLK falling. The median cross point
is used to calculate the voltage thresholds that the oscilloscope uses for the edge rate calculations. The rise edge rate of
SD_REF_CLK must be compared to the fall edge rate of SD_REF_CLK, the maximum allowed difference should not exceed
20% of the slowest edge rate. See Figure 44.
7. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing
Rise Edge Rate
Fall Edge Rate
VIH = +200 mV
0.0 V
VIL = –200 mV
SD_REF_CLK –
SD_REF_CLK
Figure 43. Differential Measurement Points for Rise and Fall Time
Figure 44. Single-Ended Measurement Points for Rise and Fall Time Matching
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
84
Freescale Semiconductor
PCI Express
2.9.2.5
SerDes Transmitter and Receiver Reference Circuits
The following figure shows the reference circuits for SerDes data lane’s transmitter and receiver.
50 Ω
SD_TXn
SD_RXn
50 Ω
Receiver
Transmitter
50 Ω
SD_TXn
SD_RXn
50 Ω
Figure 45. SerDes Transmitter and Receiver Reference Circuits
The DC and AC specification of SerDes data lanes are defined in each interface protocol section (SGMII, PCI Express, or Serial
Rapid IO) in this document based on the application usage
•
•
•
Section 2.6.4, “SGMII Interface Electrical Characteristics”
Section 2.10, “PCI Express”
Section 2.11, “Serial RapidIO (SRIO)”
Note that external AC-coupling capacitor is required for the above three serial transmission protocols with the capacitor value
defined in the specification of each protocol section.
2.9.2.6
Clocking Dependencies
The ports on the two ends of a link must transmit data at a rate that is within 600 parts per million (ppm) of each other at all
times. This is specified to allow bit rate clock sources with a ±300 ppm tolerance.
2.10
PCI Express
This section describes the DC and AC electrical specifications for the PCI Express bus of the MPC8569E.
2.10.1
PCI Express DC Requirements for SD_REF_CLK and SD_REF_CLK
For more information, see Section 2.9.2.3, “DC Level Requirement for SerDes Reference Clocks.”
2.10.2
PCI Express DC Physical Layer Specifications
This section contains the DC specifications for the physical layer of PCI Express on this device.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
85
PCI Express
2.10.2.1
PCI Express DC Physical Layer Transmitter Specifications
This section discusses the PCI Express DC physical layer transmitter specifications for 2.5 Gb/s.
The following table defines the PCI Express (2.5 Gb/s) DC specifications for the differential output at all transmitters. The
parameters are specified at the component pins.
Table 49. PCI Express (2.5Gb/s) Differential Transmitter (TX) Output DC Specifications
At recommended operating conditions with XVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typ
Max
Unit
Comments
Differential peak-to-peak
output voltage
VTX-DIFFp-p
800
10002 /
11003
1200
mV
VTX-DIFFp-p = 2 × |VTX-D+ – VTX-D–| See note 1.
De-emphasized differential
output voltage (ratio)
VTX-DE-RATIO
3.0
3.5
4.0
dB
Ratio of the VTX-DIFFp-p of the second and
following bits after a transition divided by the
VTX-DIFFp-p of the first bit after a transition. See
Note 1.
DC differential TX impedance ZTX-DIFF-DC
80
100
120
Ω
TX DC Differential mode Low Impedance
Transmitter DC impedance
40
50
60
Ω
Required TX D+ as well as D– DC Impedance
during all states
ZTX-DC
Note:
1. Specified at the measurement point into a timing and voltage compliance test load as shown in Figure 46 and measured over
any 250 consecutive TX UIs.
2. Typ-VTX-DIFFp-p with XVDD = 1.0 V
3. Typ-VTX-DIFFp-p with XVDD = 1.1 V
2.10.2.2
PCI Express DC Physical Layer Receiver Specifications
This section discusses the PCI Express DC physical layer receiver specifications for 2.5 Gb/s
The following table defines the DC specifications for the PCI Express (2.5 Gb/s) differential input at all receivers (RXs). The
parameters are specified at the component pins.
Table 50. PCI Express (2.5 Gb/s) Differential Receiver (RX) Input DC Specifications
At recommended operating conditions with ScoreVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typ
Max
Unit
Differential input VRX-DIFFp-p
peak-to-peak
voltage
175
—
1200
mV
DC differential
ZRX-DIFF-DC
input impedance
80
100
120
Ω
Comments
VRX-DIFFp-p = 2 × |VRX-D+ – VRX-D–|. See note 1.
RX DC Differential mode impedance. See Note 2.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
86
Freescale Semiconductor
PCI Express
Table 50. PCI Express (2.5 Gb/s) Differential Receiver (RX) Input DC Specifications (continued)
At recommended operating conditions with ScoreVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typ
Max
Unit
Comments
DC input
impedance
ZRX-DC
40
50
60
Ω
Powered down
DC input
impedance
ZRX-HIGH-IMP-DC
50
—
—
ΚΩ
Required RX D+ as well as D– DC Impedance when
the receiver terminations do not have power. See Note
3.
65
—
175
mV
VRX-IDLE-DET-DIFFp-p = 2 × |VRX-D+ – VRX-D–|.
Measured at the package pins of the receiver.
Electrical idle
VRX-IDLE-DETdetect threshold DIFFp-p
Required RX D+ as well as D– DC impedance
(50 ± 20% tolerance). See Notes 1 and 2.
Notes:
1. Specified at the measurement point and measured over any 250 consecutive UIs. The test load in Figure 46 must be used
as the RX device when taking measurements. If the clocks to the RX and TX are not derived from the same reference clock,
the TX UI recovered from 3500 consecutive UI must be used as a reference for the eye diagram.
2. Impedance during all LTSSM states. When transitioning from a fundamental reset to detect (the initial state of the LTSSM)
there is a 5 ms transition time before receiver termination values must be met on all unconfigured lanes of a port.
3. The RX DC common mode impedance that exists when no power is present or fundamental reset is asserted. This helps
ensure that the receiver detect circuit will not falsely assume a receiver is powered on when it is not. This term must be
measured at 300 mV above the RX ground.
2.10.3
PCI Express AC Physical Layer Specifications
This section contains the DC specifications for the physical layer of PCI Express on this device.
2.10.3.1
PCI Express AC Physical Layer Transmitter Specifications
This section discusses the PCI Express AC physical layer transmitter specifications for 2.5 Gb/s.
The following table defines the PCI Express (2.5Gb/s) AC specifications for the differential output at all transmitters (TXs).
The parameters are specified at the component pins. The AC timing specifications do not include RefClk jitter.
Table 51. PCI Express (2.5Gb/s) Differential Transmitter (TX) Output AC Specifications
At recommended operating conditions with XVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Unit Interval
UI
Minimum TX eye
width
TTX-EYE
Maximum time
TTX-EYE-MEDIANbetween the jitter to-MAX-JITTER
median and
maximum
deviation from the
median
Min
Typ
Max
399.88 400.00 400.12
Unit
Comments
ps
Each UI is 400 ps ± 300 ppm. UI does not account
for spread spectrum clock dictated variations. See
Note 1.
0.70
—
—
UI
The maximum transmitter jitter can be derived as
TTX-MAX-JITTER = 1 – TTX-EYE = 0.3 UI.
See Notes 2 and 3.
—
—
0.15
UI
Jitter is defined as the measurement variation of the
crossing points (VTX-DIFFp-p = 0 V) in relation to a
recovered TX UI. A recovered TX UI is calculated
over 3500 consecutive unit intervals of sample data.
Jitter is measured using all edges of the 250
consecutive UI in the center of the 3500 UI used for
calculating the TX UI. See Notes 2 and 3.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
87
PCI Express
Table 51. PCI Express (2.5Gb/s) Differential Transmitter (TX) Output AC Specifications (continued)
At recommended operating conditions with XVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
AC-coupling
capacitor
Symbol
CTX
Min
Typ
Max
Unit
Comments
75
—
200
nF
All transmitters are AC-coupled. The
AC-coupling is required either within the media or
within the transmitting component itself. See Note 4.
Notes:
1. No test load is necessarily associated with this value.
2. Specified at the measurement point into a timing and voltage compliance test load as shown in Figure 46 and measured over
any 250 consecutive TX UIs.
3. A TTX-EYE = 0.70 UI provides for a total sum of deterministic and random jitter budget of TTX-JITTER-MAX = 0.30 UI for the
transmitter collected over any 250 consecutive TX UIs. The TTX-EYE-MEDIAN-to-MAX-JITTER median is less than half of the total
TX jitter budget collected over any 250 consecutive TX UIs. It must be noted that the median is not the same as the mean.
The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed
to the averaged time value.
4. The MPC8569E SerDes transmitter does not have CTX built-in. An external AC-coupling capacitor is required.
2.10.3.2
PCI Express AC Physical Layer Receiver Specifications
This section discusses the PCI Express AC physical layer receiver specifications for 2.5 Gb/s.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
88
Freescale Semiconductor
PCI Express
The following table defines the AC specifications for the PCI Express (2.5 Gb/s) differential input at all receivers (RXs). The
parameters are specified at the component pins. The AC timing specifications do not include RefClk jitter.
Table 52. PCI Express (2.5 Gb/s) Differential Receiver (RX) Input AC Specifications
At recommended operating conditions with ScoreVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Unit interval
UI
Minimum
receiver eye
width
TRX-EYE
Min
Typ
Max
399.88 400.00 400.12
Maximum time TRX-EYE-MEDIA
between the
N-to-MAX-JITTER
jitter median
and maximum
deviation from
the median.
Unit
Comments
ps
Each UI is 400 ps ± 300 ppm. UI does not account for
spread spectrum clock dictated variations. See Note 1.
0.4
—
—
UI
The maximum interconnect media and transmitter jitter
that can be tolerated by the receiver can be derived as
TRX-MAX-JITTER = 1 – TRX-EYE = 0.6 UI. See Notes 2 and 3.
—
—
0.3
UI
Jitter is defined as the measurement variation of the
crossing points (VRX-DIFFp-p = 0 V) in relation to a
recovered TX UI. A recovered TX UI is calculated over
3500 consecutive unit intervals of sample data. Jitter is
measured using all edges of the 250 consecutive UI in the
center of the 3500 UI used for calculating the TX UI.
See Notes 2, 3, and 4.
Notes:
1. No test load is necessarily associated with this value.
2. Specified at the measurement point and measured over any 250 consecutive UIs. The test load in Figure 46 must be used as
the RX device when taking measurements. If the clocks to the RX and TX are not derived from the same reference clock, the
TX UI recovered from 3500 consecutive UI must be used as a reference for the eye diagram.
3. A TRX-EYE = 0.40 UI provides for a total sum of 0.60 UI deterministic and random jitter budget for the transmitter and
interconnect collected any 250 consecutive UIs. The TRX-EYE-MEDIAN-to-MAX-JITTER specification ensures a jitter distribution in
which the median and the maximum deviation from the median is less than half of the total. UI jitter budget collected over any
250 consecutive TX UIs. It must be noted that the median is not the same as the mean. The jitter median describes the point
in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. If the
clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must
be used as the reference for the eye diagram.
4. It is recommended that the recovered TX UI is calculated using all edges in the 3500 consecutive UI interval with a fit algorithm
using a minimization merit function. Least squares and median deviation fits have worked well with experimental and
simulated data.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
89
Serial RapidIO (SRIO)
2.10.4
Compliance Test and Measurement Load
The AC timing and voltage parameters must be verified at the measurement point. The package pins of the device must be
connected to the test/measurement load within 0.2 inches of that load, as shown in the following figure.
NOTE
The allowance of the measurement point to be within 0.2 inches of the package pins is
meant to acknowledge that package/board routing may benefit from D+ and D– not being
exactly matched in length at the package pin boundary. If the vendor does not explicitly
state where the measurement point is located, the measurement point is assumed to be the
D+ and D– package pins.
D+ Package
Pin
C = CTX
TX
Silicon
+ Package
D– Package
Pin
C = CTX
R = 50 Ω
R = 50 Ω
Figure 46. Compliance Test/Measurement Load
2.11
Serial RapidIO (SRIO)
This section describes the DC and AC electrical specifications for the Serial RapidIO interface of the MPC8569E, for the
LP-serial physical layer. The electrical specifications cover both single- and multiple-lane links. Two transmitters (short and
long run) and a single receiver are specified for each of three baud rates, 1.25, 2.50, and 3.125 GBaud.
Two transmitter specifications allow for solutions ranging from simple board-to-board interconnect to driving two connectors
across a backplane. A single receiver specification is given that will accept signals from both the short- and long-run transmitter
specifications.
The short-run transmitter must be used mainly for chip-to-chip connections on either the same printed-circuit board or across a
single connector. This covers the case where connections are made to a mezzanine (daughter) card. The minimum swings of the
short-run specification reduce the overall power used by the transceivers.
The long-run transmitter specifications use larger voltage swings that are capable of driving signals across backplanes. This
allows a user to drive signals across two connectors and a backplane. The specifications allow a distance of at least 50 cm at all
baud rates.
All unit intervals are specified with a tolerance of ±100 ppm. The worst case frequency difference between any transmit and
receive clock is 200 ppm.
To ensure interoperability between drivers and receivers of different vendors and technologies, AC-coupling at the receiver
input must be used.Signal Definitions
2.11.1
Signal Definitions
This section defines terms used in the description and specification of differential signals used by the LP-Serial links. Figure 47
shows how the signals are defined. The figures show waveforms for either a transmitter output (TD and TD) or a receiver input
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
90
Freescale Semiconductor
Serial RapidIO (SRIO)
(RD and RD). Each signal swings between A volts and B volts where A > B. Using these waveforms, the definitions are as
follows:
1.
2.
3.
4.
5.
6.
The transmitter output signals and the receiver input signals TD, TD, RD, and RD each have a peak-to-peak swing of
A – B volts
The differential output signal of the transmitter, VOD, is defined as VTD – VTD
The differential input signal of the receiver, VID, is defined as VRD – VRD
The differential output signal of the transmitter and the differential input signal of the receiver each range from A – B
to –(A – B) volts
The peak value of the differential transmitter output signal and the differential receiver input signal is A – B volts
The peak-to-peak value of the differential transmitter output signal and the differential receiver input signal is
2 × (A – B) volts
TD or RD
A Volts
TD or RD
B Volts
Differential Peak-to-Peak = 2 × (A – B)
Figure 47. Differential Peak-Peak Voltage of Transmitter or Receiver
To illustrate these definitions using real values, consider the case of a CML (current mode logic) transmitter that has a common
mode voltage of 2.25 V and each of its outputs, TD and TD, has a swing that goes between 2.5 and 2.0 V. Using these values,
the peak-to-peak voltage swing of the signals TD and TD is 500 mV p-p. The differential output signal ranges between 500 and
–500 mV. The peak differential voltage is 500 mV. The peak-to-peak differential voltage is 1000 mV p-p.
2.11.2
Equalization
With the use of high speed serial links, the interconnect media will cause degradation of the signal at the receiver. Effects such
as inter-symbol interference (ISI) or data dependent jitter are produced. This loss can be large enough to degrade the eye opening
at the receiver beyond what is allowed in the specification. To negate a portion of these effects, equalization can be used. The
most common equalization techniques that can be used are:
•
•
•
Pre-emphasis on the transmitter
A passive high pass filter network placed at the receiver. This is often referred to as passive equalization.
The use of active circuits in the receiver. This is often referred to as adaptive equalization.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
91
Serial RapidIO (SRIO)
2.11.3
DC Requirements for Serial RapidIO
This section explains the DC requirements for the Serial RapidIO interface.
2.11.3.1
DC Requirements for Serial RapidIO SD_REF_CLK and SD_REF_CLK
The characteristics and DC requirements of the separate SerDes reference clocks of the SRIO interface are described in
Section 2.9.2.3, “DC Level Requirement for SerDes Reference Clocks.”
2.11.3.2
DC Serial RapidIO Timing Transmitter Specifications
The LP-serial transmitter electrical and timing specifications are given in the following sections.
The differential return loss, S11, of the transmitter in each case are better than the following:
•
•
–10 dB for (Baud Frequency) ÷ 10 < Freq(f) < 625 MHz
–10 dB + 10log(f ÷ 625 MHz) dB for 625 MHz ≤ Freq(f) ≤ Baud Frequency
The reference impedance for the differential return loss measurements is 100-Ω resistive. Differential return loss includes
contributions from on-chip circuitry, chip packaging, and any off-chip components related to the driver. The output impedance
requirement applies to all valid output levels.
It is recommended that the 20%–80% rise/fall time of the transmitter, as measured at the transmitter output, in each case have
a minimum value 60 ps.
It is recommended that the timing skew at the output of an LP-serial transmitter between the two signals that comprise a
differential pair not exceed 25 ps at 1.25 GB, 20 ps at 2.50 GB, and 15 ps at 3.125 GB.
The following table defines the serial RapidIO transmitter DC specifications.
Table 53. SRIO Transmitter DC Timing Specifications—1.25, 2.5, and 3.125 GBauds
At recommended operating conditions with XVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typ
Max
Unit
Notes
VO
–0.40
—
2.30
V
1
Long-run differential output voltage
VDIFFPP
800
—
1600
mV p-p
—
Short-run differential output voltage
VDIFFPP
500
—
1000
mV p-p
—
Output voltage
Note:
1. Voltage relative to COMMON of either signal comprising a differential pair.
2.11.3.3
DC Serial RapidIO Receiver Specifications
The LP-serial receiver electrical and timing specifications are given in the following sections.
Receiver input impedance shall result in a differential return loss better that 10 dB and a common mode return loss better than
6 dB from 100 MHz to (0.8) × (baud frequency). This includes contributions from on-chip circuitry, the chip package, and any
off-chip components related to the receiver. AC coupling components are included in this requirement. The reference
impedance for return loss measurements is 100-Ω resistive for differential return loss and 25-Ω resistive for common mode.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
92
Freescale Semiconductor
Serial RapidIO (SRIO)
The following table defines the serial RapidIO receiver DC specifications.
Table 54. SRIO Receiver DC Timing Specifications—1.25 GBaud, 2.5 GBaud, 3.125 GBaud
At recommended operating conditions with ScoreVDD = 1.0 V ± 3%. and 1.1 V ± 3%.
Parameter
Differential input voltage
Symbol
Min
Typ
Max
Unit
Notes
VIN
200
—
1600
mV p-p
1
Note:
1. Measured at receiver
2.11.4
AC Requirements for Serial RapidIO
This section explains the AC requirements for the Serial RapidIO interface.
2.11.4.1
AC Requirements for Serial RapidIO SD_REF_CLK and SD_REF_CLK
Note that the Serial RapidIO clock requirements for SDn_REF_CLK and SDn_REF_CLK are intended to be used within the
clocking guidelines specified by Section 2.9.2.4, “AC Requirements for SerDes Reference Clocks.”
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
93
Serial RapidIO (SRIO)
2.11.4.2
AC Requirements for Serial RapidIO Transmitter
The following table defines the transmitter AC specifications for the Serial RapidIO. The AC timing specifications do not
include RefClk jitter
Table 55. SRIO Transmitter AC Timing Specifications
At recommended operating conditions with XVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Deterministic jitter
JD
—
—
0.17
UI p-p
—
Total jitter
JT
—
—
0.35
UI p-p
—
Unit Interval: 1.25 GBaud
UI
800 – 100ppm
800
800 + 100ppm
ps
—
Unit Interval: 2.5 GBaud
UI
400 – 100ppm
400
400 + 100ppm
ps
—
Unit Interval: 3.125 GBaud
UI
320 – 100ppm
320
320 + 100ppm
ps
—
The following table defines the receiver AC specifications for Serial RapidIO. The AC timing specifications do not include
RefClk jitter.
Table 56. SRIO Receiver AC Timing Specifications
At recommended operating conditions with ScoreVDD = 1.0 V ± 3%. and 1.1 V ± 3%.
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Deterministic jitter tolerance
JD
0.37
—
—
UI p-p
1, 3
Combined deterministic and random jitter
tolerance
JDR
0.55
—
—
UI p-p
1, 3
JT
0.65
—
—
UI p-p
1, 3
BER
—
—
10–12
—
—
Unit Interval: 1.25 GBaud
UI
800 – 100ppm
800
800 + 100ppm
ps
—
Unit Interval: 2.5 GBaud
UI
400 – 100ppm
400
400 + 100ppm
ps
—
Unit Interval: 3.125 GBaud
UI
320 – 100ppm
320
320 + 100ppm
ps
—
Total jitter tolerance2
Bit error rate
Notes:
1. Measured at receiver
2. Total jitter is composed of three components: deterministic jitter, random jitter and single frequency sinusoidal jitter. The
sinusoidal jitter may have any amplitude and frequency in the unshaded region of Figure 48. The sinusoidal jitter component
is included to ensure margin for low-frequency jitter, wander, noise, crosstalk, and other variable system effects.
3. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
94
Freescale Semiconductor
I2C
Sinusoidal Jitter Amplitude
8.5 UI p-p
0.10 UI p-p
22.1 kHz
Frequency
1.875 MHz
20 MHz
Figure 48. Single Frequency Sinusoidal Jitter Limits
2.12
I2C
This section describes the DC and AC electrical characteristics for the I2C interfaces of the MPC8569E.
2.12.1
I2C DC Electrical Characteristics
The following table provides the DC electrical characteristics for the I2C interface.
Table 57. I2C DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
0
0.4
V
2
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
95
I2C
Table 57. I2C DC Electrical Characteristics (continued)
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
tI2KHKL
0
50
ns
3
Input current each I/O pin (input voltage is between
0.1 × OVDD and 0.9 × OVDD (max) )
II
–10
10
μA
4
Capacitance for each I/O pin
CI
—
10
pF
—
Pulse width of spikes that must be suppressed by the
input filter
Notes:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. Output voltage (open drain or open collector) condition = 3 mA sink current.
3. See the MPC8569E PowerQUICC III Integrated Processor Family Reference Manual for information about the digital filter
used.
4. I/O pins obstruct the SDA and SCL lines if OVDD is switched off.
2.12.2
I2C AC Electrical Specifications
The following table provides the AC timing parameters for the I2C interface.
Table 58. I2C AC Timing Specifications
At recommended operating conditions with OVDD of 3.3 V ± 5%
Symbol1
Min
Max
Unit
Notes
SCL clock frequency
fI2C
0
400
kHz
2
Low period of the SCL clock
tI2CL
1.3
—
μs
—
High period of the SCL clock
tI2CH
0.6
—
μs
—
Setup time for a repeated START condition
tI2SVKH
0.6
—
μs
—
Hold time (repeated) START condition (after this period,
the first clock pulse is generated)
tI2SXKL
0.6
—
μs
—
Data setup time
tI2DVKH
100
—
ns
—
μs
3
—
0
—
—
Parameter
tI2DXKL
Data input hold time:
CBUS compatible masters
I2C bus devices
Data output delay time
tI2OVKL
—
0.9
μs
4
Setup time for STOP condition
tI2PVKH
0.6
—
μs
—
Bus free time between a STOP and START condition
tI2KHDX
1.3
—
μs
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
96
Freescale Semiconductor
I2C
Table 58. I2C AC Timing Specifications (continued)
At recommended operating conditions with OVDD of 3.3 V ± 5%
Symbol1
Min
Max
Unit
Notes
Noise margin at the LOW level for each connected
device (including hysteresis)
VNL
0.1 × OVDD
—
V
—
Noise margin at the HIGH level for each connected
device (including hysteresis)
VNH
0.2 × OVDD
—
V
—
Capacitive load for each bus line
Cb
—
400
pF
—
Parameter
Notes:
1. The symbols used for timing specifications herein follow the pattern t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2)
with respect to the time data input signals (D) reaching the valid state (V) relative to the tI2C clock reference (K) going to the
high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the START
condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH
symbolizes I2C timing (I2) for the time that the data with respect to the STOP condition (P) reaches the valid state (V) relative
to the tI2C clock reference (K) going to the high (H) state or setup time.
2. The requirements for I2C frequency calculation must be followed. See Freescale application note AN2919, “Determining the
I2C Frequency Divider Ratio for SCL.”
3. As a transmitter, the MPC8659E provides a delay time of at least 300 ns for the SDA signal (referred to as the VIHmin of the
SCL signal) to bridge the undefined region of the falling edge of SCL to avoid unintended generation of a START or STOP
condition. When the MPC8569E acts as the I2C bus master while transmitting, it drives both SCL and SDA. As long as the
load on SCL and SDA are balanced, the MPC8569E does not generate an unintended START or STOP condition. Therefore,
the 300 ns SDA output delay time is not a concern. If under some rare condition, the 300 ns SDA output delay time is required
for the MPC8569E as transmitter, application note AN2919, referred to in note 4 below, is recommended.
4. The maximum tI2OVKL must be met only if the device does not stretch the LOW period (tI2CL) of the SCL signal.
The following figure provides the AC test load for the I2C.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 49. I2C AC Test Load
The following figure shows the AC timing diagram for the I2C bus.
SDA
tI2DVKH
tI2KHKL
tI2KHDX
tI2SXKL
tI2CL
SCL
tI2SXKL
S
tI2CH
tI2DXKL,tI2OVKL
tI2SVKH
Sr
tI2PVKH
P
S
2
Figure 50. I C Bus AC Timing Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
97
GPIO
2.13
GPIO
This section describes the DC and AC electrical characteristics for the GPIO interface.
2.13.1
GPIO DC Electrical Characteristics
The following table provides the DC electrical characteristics for the GPIO interface when operating from a 3.3 V supply
Table 59. GPIO DC Electrical Characteristics (3.3 V)
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the min and max OVIN respective values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
2.13.2
GPIO AC Timing Specifications
The following table provides the GPIO input and output AC timing specifications.
Table 60. GPIO Input AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Unit
Notes
tPIWID
20
ns
1
GPIO inputs—minimum pulse width
Notes:
1. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs must be synchronized before use by any
external synchronous logic. GPIO inputs are required to be valid for at least tPIWID to ensure proper operation.
The following figure provides the AC test load for the GPIO.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 51. GPIO AC Test Load
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
98
Freescale Semiconductor
JTAG Controller
2.14
JTAG Controller
This section describes the DC and AC electrical specifications for the IEEE 1149.1 (JTAG) interface.
2.14.1
JTAG DC Electrical Characteristics
The following table provides the JTAG DC electrical characteristics.
Table 61. JTAG DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
2.14.2
JTAG AC Timing Specifications
The following table provides the JTAG AC timing specifications as defined in Figure 52 through Figure 55.
Table 62. JTAG AC Timing Specifications
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Notes
JTAG external clock frequency of operation
fJTG
0
33.3
MHz
—
JTAG external clock cycle time
tJTG
30
—
ns
—
tJTKHKL
15
—
ns
—
tJTGR/tJTGF
0
2
ns
4
TRST assert time
tTRST
25
—
ns
2
Input setup times
tJTDVKH
4
—
ns
—
Parameter
JTAG external clock pulse width measured at 1.4 V
JTAG external clock rise and fall times
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
99
JTAG Controller
Table 62. JTAG AC Timing Specifications (continued)
For recommended operating conditions, see Table 3
Parameter
Input hold times
Symbol1
Min
Max
Unit
Notes
tJTDXKH
10
—
ns
—
ns
3
tJTKLDV
—
—
15
10
tJTKLDX
0
—
ns
3
Output valid times:
Boundary-scan data
TDO
Output hold times
Notes:
1. The symbols used for timing specifications follow the pattern t(first two letters of functional block)(signal)(state)(reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing
(JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going to
the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D)
reaching the invalid state (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that in general, the clock
reference symbol representation is based on three letters representing the clock of a particular functional. For rise and fall
times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
2. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.
3. All outputs are measured from the midpoint voltage of the falling edge of tTCLK to the midpoint of the signal in question. The
output timings are measured at the pins. All output timings assume a purely resistive 50-Ω load. Time-of-flight delays must
be added for trace lengths, vias, and connectors in the system.
4. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing
The following figure provides the AC test load for TDO and the boundary-scan outputs of the device.
Z0 = 50 Ω
Output
RL = 50 Ω
OVDD/2
Figure 52. AC Test Load for the JTAG Interface
The following figure provides the JTAG clock input timing diagram.
JTAG
External Clock
VM
VM
VM
tJTGR
tJTKHKL
tJTGF
tJTG
VM = Midpoint Voltage (OVDD/2)
Figure 53. JTAG Clock Input Timing Diagram
The following figure provides the TRST timing diagram.
TRST
VM
VM
tTRST
VM = Midpoint Voltage (OVDD/2)
Figure 54. TRST Timing Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
100
Freescale Semiconductor
Enhanced Local Bus Controller
The following figure provides the boundary-scan timing diagram.
JTAG
External Clock
VM
VM
tJTDVKH
tJTDXKH
Boundary
Data Inputs
Input
Data Valid
tJTKLDV
tJTKLDX
Boundary
Data Outputs
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
Figure 55. Boundary-Scan Timing Diagram
2.15
Enhanced Local Bus Controller
This section describes the DC and AC electrical specifications for the enhanced local bus interface of the MPC8569E.
2.15.1 Enhanced Local Bus DC Electrical Characteristics
The following table provides the DC electrical characteristics for the enhanced local bus interface when operating at BVDD =
3.3 V DC.
Table 63. Enhanced Local Bus DC Electrical Characteristics (3.3 V DC)
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (VIN = 0 V or VIN = BVDD)
IIN
—
±40
μA
2
Output high voltage (BVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (BVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max BVIN values found in Table 3
2. The symbol VIN, in this case, represents the BVIN symbol referenced in Section 2.1.1.1, “Recommended Operating
Conditions.”
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
101
Enhanced Local Bus Controller
The following table provides the DC electrical characteristics for the enhanced local bus interface when operating at BVDD =
2.5 V DC.
Table 64. Enhanced Local Bus DC Electrical Characteristics (2.5 V DC)
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
1.70
—
V
1
Input low voltage
VIL
—
0.7
V
1
Input current (VIN = 0 V or VIN = BVDD)
IIN
—
±40
μA
2
Output high voltage (BVDD = min, IOH = –1 mA)
VOH
2.0
—
V
—
Output low voltage (BVDD = min, IOL = 1 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max BVIN values found in Table 3
2. The symbol VIN, in this case, represents the BVIN symbol referenced in Section 2.1.1.1, “Recommended Operating
Conditions.”
The following table provides the DC electrical characteristics for the enhanced local bus interface when operating at BVDD =
1.8 V DC.
Table 65. Enhanced Local Bus DC Electrical Characteristics (1.8 V DC)
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
1.25
—
V
1
Input low voltage
VIL
—
0.6
V
1
Input current (VIN = 0 V or VIN = BVDD)
IIN
—
±40
μA
2
Output high voltage (BVDD = min, IOH = –0.5 mA)
VOH
1.35
—
V
—
Output low voltage (BVDD = min, IOL = 0.5 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max BVIN values found in Table 3
2. The symbol VIN, in this case, represents the BVIN symbol referenced in Section 2.1.1.1, “Recommended Operating
Conditions.”
2.15.2
Enhanced Local Bus AC Electrical Specifications
This section describes the AC timing specifications for the enhanced local bus interface.
2.15.2.1
Test Condition
The following figure provides the AC test load for the enhanced local bus.
Output
Z0 = 50 Ω
RL = 50 Ω
BVDD/2
Figure 56. Enhanced Local Bus AC Test Load
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
102
Freescale Semiconductor
Enhanced Local Bus Controller
2.15.2.2
Enhanced Local Bus AC Timing Specifications for PLL Enable Mode
For PLL enable mode, all timings are relative to the rising edge of LSYNC_IN.
The following table describes the timing specifications of the enhanced local bus interface at BVDD = 3.3 V, 2.5 V and 1.8 V
for PLL enable mode.
Table 66. Enhanced Local Bus Timing Specifications (BVDD = 3.3 V 2.5 V and 1.8 V) —PLL Enabled Mode
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Notes
Enhanced local bus cycle time
tLBK
7.5
12
ns
—
Enhanced local bus duty cycle
tLBKH/tLBK
45
55
%
5
LCLK[n] skew to LCLK[m] or LSYNC_OUT
tLBKSKEW
—
680
ps
2
Input setup
tLBIVKH
2
—
ns
—
Input hold
tLBIXKH
1.0
—
ns
—
Output delay
(Except LALE)
tLBKHOV
—
3.8
ns
—
Output hold
(Except LALE)
tLBKHOX
0.6
—
ns
—
Enhanced local bus clock to output high
impedance for LAD/LDP
tLBKHOZ
—
3.8
ns
3
LALE output negation to LAD/LDP output
transition (LATCH hold time)
tLBONOT
1 – 0.475 ns
(LBCR[AHD]=0)
—
eLBC controller
clock cycle
(= 1 platform
clock cycle in
ns)
4
Parameter
½ – 0.475 ns
(LBCR[AHD] = 1)
Notes:
1. All signals are measured from BVDD/2 of the rising edge of LSYNC_IN to BVDD/2 of the signal in question.
2. Skew measured between different LCLK signals at BVDD/2.
3. For purposes of active/float timing measurements, the high impedance or off state is defined to be when the total current
delivered through the component pin is less than or equal to the leakage current specification.
4. tLBONOT is a measurement of the minimum time between the negation of LALE and any change in LAD. tLBONOT is determined
by LBCR[AHD]. The unit is the eLBC controller clock cycle. The eLBC controller clock refers to the internal clock that runs the
local bus controller, not the external LCLK. LCLK cycle = eLBC controller clock cycle × LCRR[CLKDIV]. After power on reset,
LBCR[AHD] defaults to 0 and eLBC runs at maximum hold time.
5. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
103
Enhanced Local Bus Controller
The following figure shows the AC timing diagram for PLL-enabled mode.
LSYNC_IN
tLBIXKH1
tLBIVKH1
Input Signals
tLBKHOV
tLBKHOX
Output Signal
(Except LALE)
LAD
(address phase)
tLBONOT
LALE
tLBKHOZ
LAD/LDP
(data phase)
Figure 57. Local Bus AC Timing Diagram (PLL Enabled)
The above figure applies to all three controllers that eLBC supports: GPCM, UPM and FCM.
For input signals, the AC timing data is used directly for all three controllers.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
104
Freescale Semiconductor
Enhanced Local Bus Controller
For output signals, each type of controller provides its own unique method to control the signal timing. The final signal delay
value for output signals is the programmed delay plus the AC timing delay. For example, for GPCM, LCS can be programmed
to delay by tacs (0, ¼, ½, 1, 1 + ¼, 1 + ½, 2, 3 cycles), so the final delay is tacs + tLBKHOV.
The following figure shows how the AC timing diagram applies to GPCM. The same principle applies to UPM and FCM.
LSYNC_IN
taddr
LAD[0:31]
address
taddr
read data
address
tLBONOT
write data
tLBONOT
LALE
LCS_B
tarcs + tLBKHOV
tawcs + tLBKHOV
tLBKHOX
LGPL2/LOE_B
taoe + tLBKHOV
tawe+ tLBKHOV
trc
LWE_B
twen
toen
twc
LBCTL
read
write
taddr is programmable and determined by LCRR[EADC] and ORx[EAD].
2 t
arcs, tawcs, taoe , trc, toen, tawe, twc, twen are determined by ORx. Refer to reference manual.
1
Figure 58. GPCM Output Timing Diagram (PLL Enabled)
2.15.2.3
Enhanced Local Bus AC Timing Specifications for PLL Bypass Mode
All output signal timings are relative to the falling edge of any LCLKs for PLL bypass mode. The external circuit must use the
rising edge of the LCLKs to latch the data.
All input timings except LUPWAIT/LFRB are relative to the rising edge of LCLKs. LUPWAIT/LFRB are relative to the falling
edge of LCLKs.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
105
Enhanced Local Bus Controller
The following table describes the timing specifications of the enhanced local bus interface at BVDD = 3.3, 2.5, and 1.8 V DC
with PLL disabled.
Table 67. Enhanced Local Bus Timing Specifications (BVDD = 3.3 V, 2.5 V, and 1.8 V)—PLL Bypassed
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Notes
Enhanced local bus cycle time
tLBK
12
—
ns
—
Enhanced local bus duty cycle
tLBKH/tLBK
45
55
%
6
LCLK[n] skew to LCLK[m] or LSYNC_OUT
tLBKSKEW
—
150
ps
2
Input setup
(except LUPWAIT/LFRB)
tLBIVKH
6.5
—
ns
—
Input hold
(except LUPWAIT/LFRB)
tLBIXKH
1
—
ns
—
Input setup
(for LUPWAIT/LFRB)
tLBIVKL
6.5
—
ns
—
Input hold
(for LUPWAIT/LFRB)
tLBIXKL
1
—
ns
—
Output delay
(Except LALE)
tLBKLOV
—
1.5
ns
—
Output hold
(Except LALE)
tLBKLOX
–3.5
—
ns
5
Enhanced local bus clock to output high
impedance for LAD/LDP
tLBKLOZ
—
2
ns
3
LALE output negation to LAD/LDP output
transition (LATCH hold time)
tLBONOT
1 – 1 ns
(LBCR[AHD] = 0)
—
eLBC
controller
clock
cycle
(=1
platform
clock
cycle in
ns)
4
Parameter
1/2 – 1 ns
(LBCR[AHD] = 1)
Notes:
1. All signals are measured from BVDD/2 of rising/falling edge of LCLK to BVDD/2 of the signal in question.
2. Skew measured between different LCLK signals at BVDD/2.
3. For purposes of active/float timing measurements, the high impedance or off state is defined to be when the total current
delivered through the component pin is less than or equal to the leakage current specification.
4. tLBONOT is a measurement of the minimum time between the negation of LALE and any change in LAD. tLBONOT is determined
by LBCR[AHD]. The unit is the eLBC controller clock cycle, which is the internal clock that runs the local bus controller, not
the external LCLK. LCLK cycle = eLBC controller clock cycle × LCRR[CLKDIV]. After power on reset, LBCR[AHD] defaults to
0 and eLBC runs at maximum hold time.
5. Output hold is negative. This means that output transition happens earlier than the falling edge of LCLK.
6. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
106
Freescale Semiconductor
Enhanced Local Bus Controller
The following figure shows the AC timing diagram for PLL bypass mode.
LCLK[m]
tLBIVKH
tLBIXKH
Input Signals
(Except LUPWAIT/LFRB)
tLBIVKL
Input Signal
(LUPWAIT/LFRB)
tLBIXKL
tLBKLOV
tLBKLOX
Output Signals
(Except LALE)
LAD
(address phase)
tLBONOT
LALE
tLBKLOZ
LAD/LDP
(data phase)
Figure 59. Enhanced Local Bus Signals (PLL Bypass Mode)
The above figure applies to all three controllers that eLBC supports: GPCM, UPM, and FCM.
For input signals, the AC timing data is used directly for all three controllers.
For output signals, each type of controller provides its own unique method to control the signal timing. The final signal delay
value for output signals is the programmed delay plus the AC timing delay. For example, for GPCM, LCS can be programmed
to delay by tacs (0, ¼, ½, 1, 1 + ¼, 1 + ½, 2, 3 cycles), so the final delay is tacs + tLBKHOV.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
107
Enhanced Secure Digital Host Controller (eSDHC)
The following figure shows how the AC timing diagram applies to GPCM in PLL bypass mode. The same principle applies to
UPM and FCM.
LCLK
taddr
LAD[0:31]
taddr
address
read data
write data
address
tLBONOT
tLBONOT
LALE
LCS_B
tarcs + tLBKHOV
tawcs + tLBKHOV
tLBKHOX
LGPL2/LOE_B
taoe + tLBKHOV
LWE_B
twen
tawe + tLBKHOV
trc
toen
twc
LBCTL
read
1
2
write
taddr is programmable and determined by LCRR[EADC] and ORx[EAD].
tarcs, tawcs, taoe, trc, toen, tawe, twc, twen are determined by ORx. Refer to the MPC8569E reference manual.
Figure 60. GPCM Output Timing Diagram (PLL Bypass Mode)
2.16
Enhanced Secure Digital Host Controller (eSDHC)
This section describes the DC and AC electrical specifications for the eSDHC interface of the MPC8569E.
2.16.1
eSDHC DC Electrical Characteristics
The following table provides the DC electrical characteristics for the eSDHC interface of the MPC8569E.
Table 68. eSDHC Interface DC Electrical Characteristics
At recommended operating conditions with OVDD = 3.3 V
Characteristic
Symbol
Condition
Min
Max
Unit
Notes
Input high voltage
VIH
—
0.625 × OVDD
—
V
1
Input low voltage
VIL
—
—
0.25 × OVDD
V
1
Output high voltage
VOH
IOH = –100 μA at
OVDD min
0.75 × OVDD
—
V
—
Output low voltage
VOL
IOL = 100 μA at
OVDD min
—
0.125 × OVDD
V
—
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
108
Freescale Semiconductor
Enhanced Secure Digital Host Controller (eSDHC)
Table 68. eSDHC Interface DC Electrical Characteristics (continued)
At recommended operating conditions with OVDD = 3.3 V
Characteristic
Symbol
Condition
Min
Max
Unit
Notes
Output high voltage
VOH
IOH = –100 μA
OVDD – 0.2
—
V
2
Output low voltage
VOL
IOL = 2 mA
—
0.3
V
2
IIN/IOZ
—
–10
10
μA
—
Unit
Notes
MHz
2, 4
Input/output leakage current
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. Open drain mode for MMC cards only.
2.16.2
eSDHC AC Timing Specifications
The following table provides the eSDHC AC timing specifications as defined in Figure 61 and Figure 62.
Table 69. eSDHC AC Timing Specifications
At recommended operating conditions with OVDD = 3.3 V
Parameter
Symbol1
SD_CLK clock frequency:
SD/SDIO full speed/high speed mode
MMC full speed/high speed mode
fSHSCK
SD_CLK clock low time—High speed/Full speed mode
Min
Max
0
25/50
20/52
tSHSCKL
7/10
—
ns
4
SD_CLK clock high time—High speed/Full speed mode
tSHSCKH
7/10
—
ns
4
SD_CLK clock rise and fall times
tSHSCKR/
tSHSCKF
—
3
ns
4, 5
Input setup times: SD_CMD, SD_DATx, SD_CD to SD_CLK
tSHSIVKH
3.7
—
ns
3, 4, 6
Input hold times: SD_CMD, SD_DATx, SD_CD to SD_CLK
tSHSIXKH
2.5
—
ns
4, 6
Output delay time: SD_CLK to SD_CMD, SD_DATx valid
tSHSKHOV
–3
3
ns
4, 6
Notes:
1. The symbols used for timing specifications follow the pattern t(first three letters of functional block)(signal)(state)(reference)(state) for inputs
and t(first three letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tFHSKHOV symbolizes eSDHC high
speed mode device timing (SHS) clock reference (K) going to the high (H) state, with respect to the output (O) reaching the
invalid state (X) or output hold time. Note that in general, the clock reference symbol representation is based on five letters
representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter:
R (rise) or F (fall).
2. In full speed mode, clock frequency value can be 0–25 MHz for a SD/SDIO card and 0–20 MHz for a MMC card. In high speed
mode, clock frequency value can be 0–50 MHz for a SD/SDIO card and 0–52 MHz for a MMC card.
3. To satisfy setup timing, one way board routing delay between Host and Card, on SD_CLK, SD_CMD and SD_DATx should
not exceed 0.65ns.
4. Ccard ≤10 pF, (1 card) and CL = CBUS + CHOST + CCARD ≤ 40 pF.
5. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing.
6. The parameter values apply to both full speed and high speed modes.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
109
Timers
The following figure provides the eSDHC clock input timing diagram.
eSDCH
External Clock
Operational Mode
VM
VM
VM
tSHSCKH
tSHSCKL
tSHSCK
tSHSCKR
tSHSCKF
VM = Midpoint Voltage (OVDD/2)
Figure 61. eSDHC Clock Input Timing Diagram
The following figure provides the data and command input/output timing diagram.
SD_CK VM
External Clock
VM
VM
VM
tSHSIVKH
tSHSIXKH
SD_DAT/CMD
Inputs
SD_DAT/CMD
Outputs
tSHSKHOV
VM = Midpoint Voltage (OVDD/2)
Figure 62. eSDHC Data and Command Input/Output Timing Diagram Referenced to Clock
2.17
Timers
This section describes the DC and AC electrical specifications for the timers of the MPC8569E.
2.17.1
Timers DC Electrical Characteristics
The following table provides the timers DC electrical characteristics.
Table 70. Timers DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
110
Freescale Semiconductor
Programmable Interrupt Controller (PIC)
2.17.2
Timers AC Timing Specifications
The following table provides the timers input and output AC timing specifications.
Table 71. Timers Input AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
Timers inputs—minimum pulse width
Symbol
Typ
Unit
Notes
tTIWID
20
ns
1, 2
Notes:
1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of CLKIN. Timings are
measured at the pin.
2. Timers inputs and outputs are asynchronous to any visible clock. Timers outputs must be synchronized before use by any
external synchronous logic. Timers inputs are required to be valid for at least tTIWID ns to ensure proper operation.
The following figure provides the AC test load for the timers.
Z0 = 50 Ω
Output
OVDD/2
RL = 50 Ω
Figure 63. Timers AC Test Load
2.18
Programmable Interrupt Controller (PIC)
This section describes the DC and AC electrical specifications for the PIC of the MPC8569E.
2.18.1
PIC DC Electrical Characteristics
The following table provides the DC electrical characteristics for the external interrupt pins IRQ[0:6], IRQ[8:11] and IRQ_OUT
of the PIC, as well as the port interrupts of the QUICC Engine block.
Table 72. PIC DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
111
SPI Interface
2.18.2
PIC AC Timing Specifications
The following table provides the PIC input and output AC timing specifications.
Table 73. PIC Input AC Timing Specifications
For recommended operating conditions, see Table 3
Parameter
PIC inputs—minimum pulse width
Symbol
Min
Max
Unit
Notes
tPIWID
3
—
SYSCLK
1
Note:
1. PIC inputs and outputs are asynchronous to any visible clock. PIC outputs must be synchronized before use by any external
synchronous logic. PIC inputs are required to be valid for at least tPIWID ns to ensure proper operation when working in
edge-triggered mode.
2.19
SPI Interface
This section describes the SPI DC and AC electrical specifications of the MPC8569E.
2.19.1
SPI DC Electrical Characteristics
The following table provides the SPI DC electrical characteristics.
Table 74. SPI DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2.0
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOH = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
2.19.2
SPI AC Timing Specifications
The following table and provide the SPI input and output AC timing specifications.
Table 75. SPI AC Timing Specifications
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Note
SPI outputs valid—Master mode (internal clock) delay
tNIKHOV
—
6
ns
2
SPI outputs hold—Master mode (internal clock) delay
tNIKHOX
0.5
—
ns
2
SPI outputs valid—Slave mode (external clock) delay
tNEKHOV
—
9
ns
2
SPI outputs hold—Slave mode (external clock) delay
tNEKHOX
2
—
ns
2
Parameter
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
112
Freescale Semiconductor
SPI Interface
Table 75. SPI AC Timing Specifications (continued)
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Note
SPI inputs—Master mode (internal clock) input setup time
tNIIVKH
4
—
ns
—
SPI inputs—Master mode (internal clock) input hold time
tNIIXKH
0
—
ns
—
SPI inputs—Slave mode (external clock) input setup time
tNEIVKH
4
—
ns
—
SPI inputs—Slave mode (external clock) input hold time
tNEIXKH
2
—
ns
—
Parameter
Note:
The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOX symbolizes the internal
timing (NI) for the time SPICLK clock reference (K) goes to the high state (H) until outputs (O) are invalid (X).
2. Output specifications are measured from the 50% level of the rising edge of CLKIN to the 50% level of the signal. Timings are
measured at the pin.
1
The following figure provides the AC test load for the SPI.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 64. SPI AC Test Load
Figure 65 and Figure 66 represent the AC timing from Table 75. Note that although the specifications generally reference the
rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge.
The following figure shows the SPI timing in slave mode (external clock).
SPICLK (output)
tNEIVKH
Input Signals:
SPIMISO
(See Note)
tNEIXKH
tNEKHOX
tNEKHOV
Output Signals:
SPIMOSI
(See Note)
Note: The clock edge is selectable on SPI.
Figure 65. SPI AC Timing in Slave Mode (External Clock) Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
113
TDM/SI
The following figure shows the SPI timing in master mode (internal clock).
SPICLK (output)
tNIIVKH
Input Signals:
SPIMISO
(See Note)
tNIIXKH
tNIKHOX
tNIKHOV
Output Signals:
SPIMOSI
(See Note)
Note: The clock edge is selectable on SPI.
Figure 66. SPI AC Timing in Master Mode (Internal Clock) Diagram
2.20
TDM/SI
This section describes the DC and AC electrical specifications for the time-division-multiplexed and serial interface of the
MPC8569E.
2.20.1
TDM/SI DC Electrical Characteristics
The following table provides the DC electrical characteristics for the MPC8569E TDM/SI.
Table 76. TDM/SI DC Electrical Characteristics
Characteristic
Symbol
Min
Max
Unit
Notes
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOH = 2 mA)
VOL
—
0.4
V
—
Input high voltage
VIH
2.0
OVDD + 0.3
V
—
Input low voltage
VIL
–0.3
0.8
V
—
Input current (0 V ≤ VIN ≤ OVDD)
IIN
—
±40
μA
1
Note:
1. The symbol VIN, in this case, represents the OVIN referenced in Table 2 and Table 3.
2.20.2
TDM/SI AC Timing Specifications
The following table provides the TDM/SI input and output AC timing specifications.
NOTE: Rise/Fall Time on QE Input Pins
The rise / fall time on QE input pins should not exceed 5ns. This must be enforced
especially on clock signals. Rise time refers to signal transitions from 10% to 90% of Vcc;
fall time refers to transitions from 90% to 10% of Vcc.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
114
Freescale Semiconductor
TDM/SI
Table 77. TDM/SI AC Timing Specifications1
Characteristic
Symbol2
Min
Max
Unit
TDM/SI outputs—External clock delay
tSEKHOV
2
11
ns
TDM/SI outputs—External clock High Impedance
tSEKHOX
2
10
ns
TDM/SI inputs—External clock input setup time
tSEIVKH
5
—
ns
TDM/SI inputs—External clock input hold time
tSEIXKH
2
—
ns
Notes:
1. Output specifications are measured from the 50% level of the rising edge of CLKIN to the 50% level of the signal. Timings are
measured at the pin.
2. The symbols used for timing specifications follow the pattern t(first two letters of functional block)(signal)(state)(reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tSEKHOX symbolizes the TDM/SI outputs
external timing (SE) for the time tTDM/SI memory clock reference (K) goes from the high state (H) until outputs (O) are invalid
(X).
The following figure provides the AC test load for the TDM/SI.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 67. TDM/SI AC Test Load
The below figure represents the AC timing from Table 77. Note that although the specifications generally reference the rising
edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge. The following figure shows
the TDM/SI timing with external clock.
TDM/SICLK (Input)
Input Signals:
TDM/SI
(See Note)
tSEIVKH
tSEIXKH
tSEKHOV
Output Signals:
TDM/SI
(See Note)
tSEKHOX
Note: The clock edge is selectable on TDM/SI.
Figure 68. TDM/SI AC Timing (External Clock) Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
115
USB Interface
2.21
USB Interface
This section provides the AC and DC electrical specifications for the USB interface of the MPC8569E.
2.21.1
USB DC Electrical Characteristics
The following table provides the USB DC electrical characteristics.
Table 78. USB DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.8
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.3
V
—
Differential input sensitivity
VDI
0.2
—
V
3
Differential common mode range
VCM
0.8
2.5
V
3
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
3. Applies to low/full speed
2.21.2
USB AC Electrical Specifications
The following table describes the general USB timing specifications.
Table 79. USB General Timing Parameters
For recommended operating conditions, see Table 3
Symbol1
Min
Max
Unit
Notes
USB clock cycle time
tUSCK
20.83
—
ns
Full speed 48 MHz
USB clock cycle time
tUSCK
166.67
—
ns
Low speed 6 MHz
tUSTSPN
—
5
ns
2
Skew among RXP, RXN, and RXD
tUSRSPND
—
10
ns
Full-speed transitions,
2
Skew among RXP, RXN, and RXD
tUSRPND
—
100
ns
Low-speed transitions,
2
Parameter
Skew between TXP and TXN
Notes:
1. The symbols used for timing specifications follow the pattern t(first two letters of functional block)(state)(signal) for receive signals and
t(first two letters of functional block)(state)(signal) for transmit signals. For example, tUSRSPND symbolizes USB timing (US) for the USB
receive signals skew (RS) among RXP, RXN, and RXD (PND). Also, tUSTSPN symbolizes USB timing (US) for the USB
transmit signals skew (TS) between TXP and TXN (PN).
2. Skew measurements are done at OVDD/2 of the rising or falling edge of the signals.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
116
Freescale Semiconductor
UTOPIA/POS Interface
The following figure provide the AC test load for the USB.
Z0 = 50 Ω
Output
OVDD/2
RL = 50 Ω
Figure 69. USB AC Test Load
2.22
UTOPIA/POS Interface
This section describes the DC and AC electrical specifications for the UTOPIA interface.
2.22.1
UTOPIA/POS DC Electrical Characteristics
The following table provides the DC electrical characteristics.
Table 80. UTOPIA/POS DC Electrical Characteristics
For recommended operating conditions, see Table 3
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage
VIH
2
—
V
1
Input low voltage
VIL
—
0.8
V
1
Input current (OVIN = 0 V or OVIN = OVDD)
IIN
—
±40
μA
2
Output high voltage (OVDD = min, IOH = –2 mA)
VOH
2.4
—
V
—
Output low voltage (OVDD = min, IOL = 2 mA)
VOL
—
0.4
V
—
Note:
1. The min VILand max VIH values are based on the respective min and max OVIN values found in Table 3.
2. The symbol OVIN represents the input voltage of the supply. It is referenced in Table 3.
2.22.2
UTOPIA/POS AC Timing Specifications
The following table provides the UTOPIA/POS input and output AC timing specifications.
Table 81. UTOPIA/POS AC Timing Specifications1
Symbol2
Min
Max
Unit
UTOPIA/POS outputs—Internal clock delay
tUIKHOV
0
8.0
ns
UTOPIA/POS outputs—External clock delay
tUEKHOV
1.0
10.0
ns
UTOPIA/POS outputs—Internal clock high Impedance
tUIKHOX
0
8.0
ns
UTOPIA/POS outputs—External clock high impedance
tUEKHOX
1.0
10.0
ns
tUIIVKH
6.4
—
ns
Characteristic
UTOPIA/POS inputs—Internal clock input setup time
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
117
UTOPIA/POS Interface
Table 81. UTOPIA/POS AC Timing Specifications1 (continued)
Symbol2
Min
Max
Unit
UTOPIA/POS inputs—External clock input setup time
tUEIVKH
4.0
—
ns
UTOPIA/POS inputs—Internal clock input hold time
tUIIXKH
0
—
ns
UTOPIA/POS inputs—External clock input hold time
tUEIXKH
1.2
—
ns
Characteristic
Notes:
1. Output specifications are measured from the 50% level of the rising edge of CLKIN to the 50% level of the signal. Timings are
measured at the pin.
2. The symbols used for timing specifications follow the pattern t(first two letters of functional block)(signal)(state)(reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUIKHOX symbolizes the UTOPIA/POS
outputs internal timing (UI) for the time tUtopia memory clock reference (K) goes from the high state (H) until outputs (O) are
invalid (X).
The following figure provides the AC test load for the UTOPIA/POS.
Z0 = 50 Ω
Output
RL = 50 Ω
OVDD/2
Figure 70. UTOPIA/POS AC Test Load
Figure 71 and Figure 72 represent the AC timing from Table 81. Note that although the specifications generally reference the
rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge.
The following figure shows the UTOPIA/POS timing with external clock.
UTOPIACLK (Input)
tUEIVKH
tUEIXKH
Input Signals:
UTOPIA
tUEKHOV
Output Signals:
UTOPIA
tUEKHOX
Figure 71. UTOPIA/POS AC Timing (External Clock) Diagram
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
118
Freescale Semiconductor
Thermal Characteristics
The following figure shows the UTOPIA/POS timing with internal clock.
UTOPIACLK (Output)
tUIIVKH
tUIIXKH
Input Signals:
UTOPIA
tUIKHOV
Output Signals:
UTOPIA
tUIKHOX
Figure 72. UTOPIA/POS AC Timing (Internal Clock) Diagram
3
Thermal
This section describes the thermal specifications of the MPC8569E.
3.1
Thermal Characteristics
The following table provides the package thermal characteristics of the MPC8569E.
Table 82. Package Thermal Characteristics
Characteristic
JEDEC Board
Symbol
Value
Unit
Notes
Junction-to-ambient Natural Convection
Single layer board (1s)
RθJA
16
°C/W
1, 2
Junction-to-ambient Natural Convection
Four layer board (2s2p)
RθJA
12
°C/W
1, 2
Junction-to-ambient (at 200 ft/min)
Single layer board (1s)
RθJA
12
°C/W
1, 2
Junction-to-ambient (at 200 ft/min)
Four layer board (2s2p)
RθJA
9
°C/W
1, 2
Junction-to-board thermal
—
RθJB
5
°C/W
3
Junction-to-case thermal
—
RθJC
1.0
°C/W
4
Notes:
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
2. Per JEDEC JESD51-2 and JESD51-6 with the board (JESD51-9) horizontal.
3. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
4. Junction-to-case at the top of the package determined using MIL-STD 883 Method 1012.1. The cold plate temperature is used
for the case temperature. Reported value includes the thermal resistance of the interface layer.
3.2
Recommended Thermal Model
Information about Flotherm models of the package or thermal data not available in this document can be obtained from your
local Freescale sales office.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
119
Thermal Management Information
3.3
Thermal Management Information
This section provides thermal management information for the flip chip plastic ball grid array (FC-PBGA) package for
air-cooled applications. Proper thermal control design is primarily dependent on the system-level design—the heat sink, airflow,
and thermal interface material.
The recommended attachment method to the heat sink is illustrated in the following figure. The heat sink must be attached to
the printed-circuit board with the spring force centered over the package. This spring force should not exceed 10 pounds force
(45 Newtons).
Heat Sink
FC-PBGA Package
Heat Sink
Clip
Adhesive or
Thermal Interface Material
Die Lid
Die
Printed-Circuit Board
Figure 73. Package Exploded Cross-Sectional View
The system board designer can choose among several types of commercially-available heat sinks to determine the appropriate
one to place on the device. Ultimately, the final selection of an appropriate heat sink depends on factors such as thermal
performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost.
3.3.1
Internal Package Conduction Resistance
For the package, the intrinsic internal conduction thermal resistance paths are as follows:
•
•
The die junction-to-case thermal resistance
The die junction-to-board thermal resistance
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
120
Freescale Semiconductor
Thermal Management Information
The following figure depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit
board.
Radiation
External Resistance
Convection
Heat Sink
Thermal Interface Material
Die/Package
Die Junction
Package/Leads
Internal Resistance
Printed-Circuit Board
External Resistance
Radiation
Convection
(Note the internal versus external package resistance.)
Figure 74. Package with Heat Sink Mounted to a Printed-Circuit Board
The heat sink removes most of the heat from the device. Heat generated on the active side of the chip is conducted through the
silicon and the heat sink attach material (or thermal interface material), and to the heat sink. The junction-to-case thermal
resistance is low enough that the heat sink attach material and heat sink thermal resistance are the dominant terms.
3.3.2
Thermal Interface Materials
A thermal interface material is required at the package-to-heat sink interface to minimize the thermal contact resistance. The
performance of thermal interface materials improves with increased contact pressure; this performance characteristic chart is
generally provided by the thermal interface vendor. The recommended method of mounting heat sinks on the package is by
means of a spring clip attachment to the printed-circuit board (see Figure 73).
The system board designer can choose among several types of commercially-available thermal interface materials.
3.3.3
Temperature Diode
The device has a temperature diode on the microprocessor that can be used in conjunction with other system temperature
monitoring devices (such as On Semiconductor, NCT1008™). These devices use the negative temperature coefficient of a diode
operated at a constant current to determine the temperature of the microprocessor and its environment.
The following are the specifications of the MPC8569E on-board temperature diode:
Operating range: 10 – 230 μA
Ideality factor over 13.5 – 220 μA; n = 1.006 +/- 0.008
4
Package Description
The following section describes the detailed content and mechanical description of the package.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
121
Package Parameters for the MPC8569E
4.1
Package Parameters for the MPC8569E
The following table provides the package parameters for the FC-PBGA. The package type is 29 mm × 29 mm, 783 plastic ball
grid array (FC-PBGA).
Table 83. Package Parameters
Parameter
Package outline
Interconnects
Ball pitch
PBGA
29 mm × 29 mm
783
1 mm
Ball diameter (typical)
0.6 mm
Solder ball (lead-free)
96.5% Sn
3% Ag
0.5% Cu
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
122
Freescale Semiconductor
Mechanical Dimensions of the FC-PBGA with Full Lid
4.2
Mechanical Dimensions of the FC-PBGA with Full Lid
The following figure shows the mechanical dimensions and bottom surface nomenclature for the MPC8569E FC-PBGA
package with full lid.
Notes:
1All dimensions are in millimeters.
2Dimensions and tolerances per ASME Y14.5M-1994.
3
Maximum solder ball diameter measured parallel to datum A.
4Datum A, the seating plane, is determined by the spherical crowns of the solder balls.
5Parallelism measurement shall exclude any effect of mark on top surface of package.
6
All dimensions are symmetric across the package center lines unless dimensioned otherwise.
729.2 mm maximum package assembly (lid and laminate) x and y.
Figure 75. MPC8569E FC-PBGA Package with Full Lid
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
123
Part Numbers Fully Addressed by This Document
5
Ordering Information
Contact your local Freescale sales office or regional marketing team for ordering information.
Ordering information for the parts fully covered by this specification document is provided in Section 5.1, “Part Numbers Fully
Addressed by This Document.”
5.1
Part Numbers Fully Addressed by This Document
The following table shows the device nomenclature.
Table 84. Device Nomenclature
MPC
nnnn
E
Product
Code1
Part
Identifier
Security
Engine
MPC
PPC
8569
C
VT
Temperature
Package 2
Range
Blank = 0° to
105°C
E = included C = –40° to
105°C
AA
X
G
R
Processor
Frequency 3
DDR
Frequency4
QE
Frequency
Revision Level
VT = Pb
AN = 800 MHz K = 600 MHz G = 400 MHz Blank = Rev. 1.0 (SVR
free,
AQ = 1067 MHz L = 667 MHz J = 533 MHz
= 0x8088_0010
FC-PBGA AU = 1333 MHz N = 800 MHz L = 667 MHz
A = Rev. 2.0 (SVR
= 0x8088_0020
B = Rev. 2.1 (SVR
= 0x8088_0021
Blank = not
included
A = Rev. 2.0 (SVR
= 0x8080_0020
B = Rev. 2.1 (SVR
= 0x8080_0021
Notes:
1. MPC stands for “qualified.” PPC stands for pre-production samples.
2. See Section 4, “Package Description,” for more information on available package types.
3. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this specification
support all core frequencies. Additionally, parts addressed by part number specifications may support other maximum core
frequencies.
4. See Table 85 for the corresponding maximum platform frequency.
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
124
Freescale Semiconductor
Part Marking
5.2
Part Marking
Parts are marked as the example shown in the following figure.
MPC8569xxxxxx
MMMMM CCCCC
ATWLYYWW
FC-PBGA
Notes:
MPC8569xxxxxx is the orderable part number.
MMMMM is the mask number.
CCCCC is the country of assembly. This space is left blank if
parts are assembled in the United States.
ATWLYYWW is the traceability code.
Figure 76. Part Marking for FC-PBGA Device
5.3
Part Numbering
The following table list all part numbers that are offered for MPC8569E.
Table 85. MPC8569 Part Numbers
Core / DDR / QE /
Platform (MHz)
Standard Temp
Without Security
Standard Temp
With Security
Extended Temp
Without Security
Extended Temp
With Security
800 / 600 / 400 / 400
MPC8569VTANKG
MPC8569EVTANKG MPC8569CVTANKG MPC8569ECVTANKG
1, 2
1067 / 667/ 533 / 533
MPC8569VTAQLJ
MPC8569EVTAQLJ
MPC8569CVTAQLJ
MPC8569ECVTAQLJ
1, 2
1333 / 800 / 667 / 533
MPC8569VTAUNL
MPC8569EVTAUNL
—
—
1, 2
Note
Notes:
1. Standard Temperature and Extended Temperature with Security parts are available for Pre-production samples. The prefix is
PPC instead of MPC.
2. Part numbers that end with a “blank” indicate rev 1.0 silicon; part numbers that end with an “A” are rev 2.0 silicon; part numbers
that end with a “B” are rev 2.1 silicon.
6
Product Documentation
The following documents are required for a complete description of the device and are needed to design properly with the part.
•
•
•
MPC8569E PowerQUICC III Integrated Processor Reference Manual (document number: MPC8569ERM)
e500 PowerPC Core Reference Manual (document number: E500CORERM)
QUICC Engine Block Reference Manual with Protocol Interworking (document number: QEIWRM)
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
Freescale Semiconductor
125
Part Numbering
7
Document Revision History
The following table provides a revision history for this document.
.
Table 86. Document Revision History
Revision
Date
Substantive Change(s)
1
02/2012
• In Table 1, “MPC8569E Pinout Listing,” updated pin U20 from Reserved to THERM1 (internal
thermal diode anode) and pin U21 from Reserved to THERM0 (internal thermal diode cathode).
Removed note 9 and added note 32 to pins U20 and U21.
• In Table 38, “SGMII Transmit AC Timing Specifications,” updated min and typical values for the AC
coupling capacitor parameter.
• In Table 48, “SD_REF_CLK and SD_REF_CLK Input Clock Requirements,” removed the condition
that the reference clock duty cycle should be measured at 1.6 V.
• Added Section 2.6.5.1, “QUICC Engine Block IEEE 1588 DC Specifications.”
• Added Section 3.3.3, “Temperature Diode.”
0
06/2011
Initial public release
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1
126
Freescale Semiconductor
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
[email protected]
Document Number: MPC8569EEC
Rev. 1
02/2012
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale, the Freescale logo, and PowerQUICC are trademarks of
Freescale Semiconductor, Inc. Reg., U.S. Pat. & Tm. Off. QUICC Engine is a
trademark of Freescale Semiconductor, Inc. All other product or service
names are the property of their respective owners. The Power Architecture
and Power.org word marks and the Power and Power.org logos and related
marks are trademarks and service marks licensed by Power.org.
© 2008–2012 Freescale Semiconductor, Inc.