Quick Start Guide for TWR-K60N512 TWR-K60N512 Low-power MCU with USB, Ethernet and security TOWER SYSTEM TOWER SYSTEM Get to Know the TWR-K60N512 SW1 Primary Connector SW2 Infra-red Touch TWRPI Socket General Purpose Tower Plug-In (TWRPI) Socket LED/Touch Buttons E1–E4 SW3 (Reset) Power/OSJTAG Mini-B USB Connector MK60N512 VMD100 Microcontroller Secondary Connector MMA7660 Accelerometer Figure 1: Front Side of TWR-K60N512 Module Not Including TWRPI. TWR-K60N512 The TWR-K60N512 microcontroller module is part of the Freescale Tower System, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. Take your design to the next level and begin constructing your Tower System today by visiting freescale.com/tower for additional Tower System microcontroller modules and compatible peripherals. Quick Start Guide for TWR-K60N512 TOWER SYSTEM SD Card Socket Potentiometer VBAT (RTC) Battery Holder Figure 2: Back Side of TWR-K60N512 Module. TOWER SYSTEM Step-by-Step Installation Instructions In this Quick Start Guide, you will learn how to set up the TWR-K60N512 module and run the default demonstration. STEP 1 Install the Software and Tools Install the P&E Micro Kinetis Tower Toolkit to install the OSJTAG and USB-to-Serial drivers. These can be found on the DVD under Software. STEP 3 Tilt the board side to side to see the LEDs on E1–E4 light up as it is tilted. While the board is held flat, touch the pads on E1–E4 to toggle the LEDs. STEP STEP 2 Configure the Hardware Install the included battery into the VBAT (RTC) battery holder. Then, connect one end of the USB cable to the PC and the other end to the Power/ OSJTAG mini-B connector on the TWRK60N512 module. Allow the PC to automatically configure the USB drivers if needed. Tilt the Board 4 Play the Memory Game Press SW2 to play a memory recall game using the touch pads E1–E4. A sequence will light up, and then press the touch pads in the order flashed. If an incorrect sequence is touched or you take too long, all the lights will blink rapidly and the game will reset. Press SW1 to go back to the accelerometer demo. Quick Start Guide for TWR-K60N512 STEP Explore Further by Conducting Lab 1: TWR-K60N512 Quick Start Demo 5 Explore all the features and capabilities of the pre-programmed demo by reviewing the lab document located at freescale. com/TWR-K60N512. STEP Learn More About the Kinetis K60 Microcontrollers 6 Find more MQX and bare-metal labs and software for the Kinetis K60 microcontrollers at freescale.com/TWR-K60N512. TOWER SYSTEM TOWER SYSTEM Jumper Options The following is a list of all the jumper options. The default installed jumper settings are shown in bold. Jumper Option Setting Description J8 MCU Power Connection ON Connect on-board 3.3V supply to MCU OFF Isolate MCU from power (connect an ammeter to measure current) VBAT Power Selection 1-2 Connect VBAT to on-board 3.3V supply 2-3 Connect VBAT to the higher voltage between on-board 3.3V supply or coin-cell supply Clock Input Source Selection 1-2 Connect main EXTAL to on-board 50 MHz clock 2-3 Connect EXTAL to the CLKIN0 signal on the elevator connector ON OSJTAG bootloader mode (OSJTAG firmware reprogramming) OFF Debugger mode J9 J6 J10 OSJTAG Bootloader Selection Quick Start Guide for TWR-K60N512 TOWER SYSTEM Jumper Option Setting Description J12 JTAG Board Power Connection ON Connect on-board 5V supply to JTAG port (supports powering board from JTAG pod supporting 5V supply output) OFF Disconnect on-board 5V supply to JTAG port ON Connect PTD7/CMT_IRO to IR Transmitter (D507) OFF Disconnect PTD7/CMT_IRO from IR Transmitter (D507) ON Connect USB0_VBUS from Elevator to VREGIN OFF Disconnect USB0_VBUS from Elevator to VREGIN J2 J1 IR Transmitter Connection VREGIN Power Connection TOWER SYSTEM To learn more about the TWR-K60N512 and other Freescale Kinetis microcontroller products, please visit freescale.com/TWR-K60N512, freescale.com/Kinetis and freescale.com/Tower. Freescale, the Freescale logo and CodeWarrior are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Flexis, Kinetis and Processor Expert are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © 2010 Freescale Semiconductor, Inc. Doc Number: TWRK60QSG / REV 0 Agile Number: 926-78535 / REV A